Indoor air quality at a waste incineration plant in Finland

Waste has been incinerated for energy utilization for more than a hundred years, but the harmful emissions emitted from the incineration plants did not begin to cause concern until the 1980s. Many plants were shutdown and the waste incineration plant in Kyläsaari Helsinki was one of them. In later years, new landfill regulations have increased the interest in waste incineration. During the last year, four new plants were taken into operation in Finland, Westenergy in Vaasa among them. The presence of dust has been observed indoors at Westenergy waste incineration plant. Dust is defined as particles with a diameter above 10 μm, while fine particles have a diameter smaller than 2.5 μm, ultrafine under 0.1 μm and nanoparticles under 0.05 μm. In recent years, the focus of particle health research has been changed to investigate smaller particles. Ultrafine particles have been found to be more detrimental to health than larger particles. Limit values regulating the concentrations of ultrafine particles have not been determined yet. The objective of this thesis was to investigate dust and particles present inside the Westenergy waste incineration facility. The task was to investigate the potential pollutant sources and to give recommendations of how to minimize the presence of dust and particles in the power plant. The total particle number concentrations and size distributions where measured at 15 points inside the plant with an Engine Exhaust Particle Sizer (EEPS) Spectrometer. The measured particles were mainly in the ultrafine size range. Dust was only visually investigated, since the main purpose was to follow the dust accumulation. The measurement points inside the incineration plant were chosen according to investigate exposure to visitors and workers. At some points probable leakage of emissions were investigated. The measurements were carried out during approximately one month in March–April 2013. The results of the measurements showed that elevated levels of dust and particles are present in the indoor air at the waste incineration plant. The cleanest air was found in the control room, warehouse and office. The most polluted air was near the sources that were investigated due to possible leakage and in the bottom ash hall. However, the concentrations were near measured background concentrations in European cities and no leakage could be detected. The high concentrations were assumed to be a result of a lot of dust and particles present on surfaces that had not been cleaned in a while. The main source of the dust and particles present inside the waste incineration plant was thought to be particles and dust from the outside air. Other activities in the area around the waste incineration facility are ground work activities, stone crushing and traffic, which probably are sources of particle formation. Filtration of the outside air prior entering the facility would probably save personnel and visitors from nuisance and save in cleaning and maintenance costs.

Wastewater Treatment of Diesel Power Plant

Diplomityön tavoitteena on selvittää Wärtsilän dieselvoimalaitosten jätevedenkäsittelyn vallitseva tila. Tutkimuksessa keskitytään raskaspolttoöljykäyttöisiin voimalaitoksiin. Työssä selvitetään yleisimmät dieselvoimalaitosten jätevesille asetetut vaatimukset. Selvitys tehdään keräämälläja tutkimalla dieselvoimalaitosten jätevesille sovellettuja standardeja. Työssä selvitetään myös dieselvoimalaitokselta ulostulevan jäteveden laatu sekä nykyisen jätevedenkäsittelyjärjestelmän toiminta. Selvitys tehdään keräämällä ja tutkimalla yrityksen sisäisiä tietoja, sekä ottamalla ja analysoimalla jätevesinäytteitä. Näytteiden otto ja analysointi toteutetaan vierailemallakahdessa voimalaitoksessa sekä yhdessä muussa kohteessa. Jäteveden laatu ennen ja jälkeen käsittelyn määritetään. Myös öljynjalostusteollisuuden jätevedenkäsittelyä tarkastellaan kirjallisuuteen pohjautuen. Tarkastelun tavoitteena on hankkia tietoa jätevedenkäsittelystä kohteissa, joissa jäteveden laatu vastaa dieselvoimalaitoksella syntyvää jätevettä. Vertailun vuoksi myös öljynjalostusteollisuudelle asetetuttuja jätevesistandardeja tutkitaan. Lisäksi työssä tutkitaan myös joitakin muita jätevedenkäsittelymenetelmiä. Diplomityön tuloksena määritetään dieselvoimalaitosten jätevedenkäsittelyn tulevaisuuden haasteet ja mahdollisuudet.

Anaerobic treatment of deinking pulp plant effluents

Anaerobic treatment as a first biological stage in wastewater treatment is nowadays a well-established technology in recycled paper processing mills using closed water circuits. Today further developed high-rate processes and especially high-tower reactors are also able to handle lower organic loads and become therefore feasible for deinking pulp plant effluents. The interest in the anaerobic method is based on a positive energy balance in form of biogas production and low biomass yield from the process. The anaerobic treatment method was researched and its suitability for the deinking pulp plant effluents was tested experimentally at Stora Enso Maxau mill. In the theory, the deinking pulp process is introduced and the effluents from the deinking process are characterized. The anaerobic treatment is brought up in depth in terms of its use for the deinking effluents, and different kind of reactor types are presented. In addition, other wastewater treatment methods are shortly introduced with the focus on tertiary treatment. Static biodegradability tests were carried out for the wastewaters both anaerobically and aerobically. Based on the results, the deinking effluents can be degraded anaerobically, and inhibition to the methanogenic bacteria was not noticed. In the aerobic static test a good performance of the existing wastewater treatment plant at Maxau mill was proved. Later on pilot trials with sequential anaerobic-aerobic treatment were carried out for the deinking effluents. The anaerobic reactor used was a so called internal circulation reactor. The results confirmed that the combination of the anaerobic treatment and the aerobic activated sludge process is a suitable method for deinking wastewaters with a COD reduction as good as with a two stage aerobic method. When combined with the outstanding quality of the produced biogas and the cost savings acquired from the lower sludge production, the anaerobic treatment was found to be an especially favorable treatment method.

Nitrogen Oxides Reduction Possibilities at Pulp Mill and Power Plant

Tutkimuksen tarkoituksena oli selvittää typenoksidien vähennysmahdollisuudet Stora Enson Varkauden tehtaiden sellutehtaalla ja voimalaitoksella. Tutkimuksessa käsiteltiin tehdasalueen suurimpia typenoksidien päästölähteitä: soodakattilaa, meesauunia, kuorikattilaa, öljykattilaa ja muovi-alumiinijakeen kaasutuslaitosta. Tutkimuksessa selvitettiin typenoksidipäästöjen syntymekanismit ja erilaisiin polttotekniikoihin soveltuvat typenoksidien vähennystekniikat. Varkauden tehtaiden typenoksidien vuosipäästö vuonna 2001 oli 836 tonnia. Kansallinen lainsäädäntö, kansainväliset sopimukset sekä paras käytettävissä oleva tekniikka (BAT) huomioiden selvitettiin kuhunkin kohteeseen parhaiten soveltuvat ratkaisut. Tutkimuksen perusteella laadittiin toimenpideohjelma, joka määrittelee suositeltavan toteutusjärjestyksen typenoksidien vähennystoimenpiteille. Toimenpideohjelman tärkeimpinä kriteereinä pidettiin vuonna 2004 tulevan uuden ympäristöluvan arvioituja luparajoja sekä toimenpiteiden kustannustehokkuutta. Toteutusjärjestyksessä ensimmäiseksi valittiin koeajojakson järjestäminen ajon optimoimiseksi kiertopetikattilalla ja toiseksi meesauunin ajon optimointi jatkuvatoimisen NOx-analysaattorin avulla. Seuraaviksi toimenpiteiksi ehdotettiin vertikaali-ilmajärjestelmän käyttöönottoa soodakattilalla sekä SNCR-järjestelmän asennusta kuorikattilalle. Saavutettava NOx-vähennys tulisi olemaan 10 – 45 % ja hinta 30 – 3573 EUR vähennettyä NOx-tonnia kohti. Tutkimuksen osana Ilmatieteen laitoksella teetetyn typenoksidien leviämisselvityksen mukaan Stora Enson tehtaiden NOx-päästöjen vaikutus Varkauden ilmanlaatuun on hyvin pieni. Suurin osa NOx-päästöistä aiheutuu liikenteestä.

Quality potential of DIP and hardwood CTMP based raw materials in woodcontaining printing paper

The objective of the thesis was to define the quality potential of DIP and hardwood CTMP based raw material furnish for a printing paper production and to define the end product's pulp-based boundary conditions especially when thinking of Chinese markets. Although the Chinese paper industry expands rapidly, the production of some paper grades is still exiguous. Especially the softwood resources are limited in Asia, thus the purpose of the thesis was to find out the possibilities to produce printing paper in China from local raw materials. Bleached CTMP can be produced, for example, from fast-growing hardwood species like eucalyptus and poplar. Therefore in this thesis it was examined if good quality printing paper is possible to produce by using deinked pulp and hardwood CTMP based furnish. In the first section of experimental part, various deinked pulps and chemithermomechanical pulps were compared. The deinked pulps were from China, Central Europe and Finland. Central European was made for magazine papers, and the Chinese as well as the Finnish pulps were made for newsprints. Two of the BCTMPs were from China and those both were made from poplar, whereas one BCTMP was made from eucalyptus in a pilot plant. There were significant differences especially between BCTMPs and their paper properties. In the second section of experimental part, the deinked pulp and eucalyptus BCTMP were blended to produce handsheets. The results show that producing the highest quality printing paper would be difficult from these raw materials. Deinked pulp affected especially the strength and optical properties as well as calender blackening. The BCTMP was found to have effects mostly on the smoothness, strength and optical properties as well as calender blackening.