Error Modeling and Accuracy Analysis of a Novel Mobile Hybrid Parallel Robot

Over the last decades, calibration techniques have been widely used to improve the accuracy of robots and machine tools since they only involve software modification instead of changing the design and manufacture of the hardware. Traditionally, there are four steps are required for a calibration, i.e. error modeling, measurement, parameter identification and compensation. The objective of this thesis is to propose a method for the kinematics analysis and error modeling of a newly developed hybrid redundant robot IWR (Intersector Welding Robot), which possesses ten degrees of freedom (DOF) where 6-DOF in parallel and additional 4-DOF in serial. In this article, the problem of kinematics modeling and error modeling of the proposed IWR robot are discussed. Based on the vector arithmetic method, the kinematics model and the sensitivity model of the end-effector subject to the structure parameters is derived and analyzed. The relations between the pose (position and orientation) accuracy and manufacturing tolerances, actuation errors, and connection errors are formulated. Computer simulation is performed to examine the validity and effectiveness of the proposed method.

Modeling and Analysis of Noise and Interconnects for On-Chip Communication Link Design

This thesis considers modeling and analysis of noise and interconnects in onchip communication. Besides transistor count and speed, the capabilities of a modern design are often limited by on-chip communication links. These links typically consist of multiple interconnects that run parallel to each other for long distances between functional or memory blocks. Due to the scaling of technology, the interconnects have considerable electrical parasitics that affect their performance, power dissipation and signal integrity. Furthermore, because of electromagnetic coupling, the interconnects in the link need to be considered as an interacting group instead of as isolated signal paths. There is a need for accurate and computationally effective models in the early stages of the chip design process to assess or optimize issues affecting these interconnects. For this purpose, a set of analytical models is developed for on-chip data links in this thesis. First, a model is proposed for modeling crosstalk and intersymbol interference. The model takes into account the effects of inductance, initial states and bit sequences. Intersymbol interference is shown to affect crosstalk voltage and propagation delay depending on bus throughput and the amount of inductance. Next, a model is proposed for the switching current of a coupled bus. The model is combined with an existing model to evaluate power supply noise. The model is then applied to reduce both functional crosstalk and power supply noise caused by a bus as a trade-off with time. The proposed reduction method is shown to be effective in reducing long-range crosstalk noise. The effects of process variation on encoded signaling are then modeled. In encoded signaling, the input signals to a bus are encoded using additional signaling circuitry. The proposed model includes variation in both the signaling circuitry and in the wires to calculate the total delay variation of a bus. The model is applied to study level-encoded dual-rail and 1-of-4 signaling. In addition to regular voltage-mode and encoded voltage-mode signaling, current-mode signaling is a promising technique for global communication. A model for energy dissipation in RLC current-mode signaling is proposed in the thesis. The energy is derived separately for the driver, wire and receiver termination.

Modeling and Simulation ofReal-Time System as a Tool to Improve Capacity Management - Case Fenix

Tämän tutkimustyön kohteena on TietoEnator Oy:n kehittämän Fenix-tietojärjestelmän kapasiteettitarpeen ennustaminen. Työn tavoitteena on tutustua Fenix-järjestelmän eri osa-alueisiin, löytää tapa eritellä ja mallintaa eri osa-alueiden vaikutus järjestelmän kuormitukseen ja selvittää alustavasti mitkä parametrit vaikuttavat kyseisten osa-alueiden luomaan kuormitukseen. Osa tätä työtä on tutkia eri vaihtoehtoja simuloinnille ja selvittää eri vaihtoehtojen soveltuvuus monimutkaisten järjestelmien mallintamiseen. Kerätyn tiedon pohjaltaluodaan järjestelmäntietovaraston kuormitusta kuvaava simulaatiomalli. Hyödyntämällä mallista saatua tietoa ja tuotantojärjestelmästä mitattua tietoa mallia kehitetään vastaamaan yhä lähemmin todellisen järjestelmän toimintaa. Mallista tarkastellaan esimerkiksi simuloitua järjestelmäkuormaa ja jonojen käyttäytymistä. Tuotantojärjestelmästä mitataan eri kuormalähteiden käytösmuutoksia esimerkiksi käyttäjämäärän ja kellonajan suhteessa. Tämän työn tulosten on tarkoitus toimia pohjana myöhemmin tehtävälle jatkotutkimukselle, jossa osa-alueiden parametrisointia tarkennetaan lisää, mallin kykyä kuvata todellista järjestelmää tehostetaanja mallin laajuutta kasvatetaan.

Modeling and measuring organizational renewal capability

Globalization and new information technologies mean that organizations have to face world-wide competition in rapidly transforming, unpredictable environments, and thus the ability to constantly generate novel and improved products, services and processes has become quintessential for organizational success. Performance in turbulent environments is, above all, influenced by the organization's capability for renewal. Renewal capability consists of the ability of the organization to replicate, adapt, develop and change its assets, capabilities and strategies. An organization with a high renewal capability can sustain its current success factors while at the same time building new strengths for the future. This capability does not only mean that the organization is able to respond to today's challenges and to keep up with the changes in its environment, but also that it can actas a forerunner by creating innovations, both at the tactical and strategic levels of operation and thereby change the rules of the market. However, even though it is widely agreed that the dynamic capability for continuous learning, development and renewal is a major source of competitive advantage, there is no widely shared view on how organizational renewal capability should be defined, and the field is characterized by a plethora of concepts and definitions. Furthermore,there is a lack of methods for systematically assessing organizational renewal capability. The dissertation aims to bridge these gaps in the existing research by constructing an integrative theoretical framework for organizational renewal capability and by presenting a method for modeling and measuring this capability. The viability of the measurement tool is demonstrated in several contexts, andthe framework is also applied to assess renewal in inter-organizational networks. In this dissertation, organizational renewal capability is examined by drawing on three complimentary theoretical perspectives: knowledge management, strategic management and intellectual capital. The knowledge management perspective considers knowledge as inherently social and activity-based, and focuses on the organizational processes associated with its application and development. Within this framework, organizational renewal capability is understood as the capacity for flexible knowledge integration and creation. The strategic management perspective, on the other hand, approaches knowledge in organizations from the standpoint of its implications for the creation of competitive advantage. In this approach, organizational renewal is framed as the dynamic capability of firms. The intellectual capital perspective is focused on exploring how intangible assets can be measured, reported and communicated. From this vantage point, renewal capability is comprehended as the dynamic dimension of intellectual capital, which consists of the capability to maintain, modify and create knowledge assets. Each of the perspectives significantly contributes to the understanding of organizationalrenewal capability, and the integrative approach presented in this dissertationcontributes to the individual perspectives as well as to the understanding of organizational renewal capability as a whole.

Emancipating and developing learning activity: Systemic intervention and re-instrumentation in higher education.

The central theme of this thesis is the emancipation and further development of learning activity in higher education in the context of the ongoing digital transformation of our societies. It was developed in response to the highly problematic mainstream approach to digital re-instrumentation of teaching and studying practises in contemporary higher education. The mainstream approach is largely based on centralisation, standardisation, commoditisation, and commercialisation, while re-producing the general patterns of control, responsibility, and dependence that are characteristic for activity systems of schooling. Whereas much of educational research and development focuses on the optimisation and fine-tuning of schooling, the overall inquiry that is underlying this thesis has been carried out from an explicitly critical position and within a framework of action science. It thus conceptualises learning activity in higher education not only as an object of inquiry but also as an object to engage with and to intervene into from a perspective of intentional change. The knowledge-constituting interest of this type of inquiry can be tentatively described as a combination of heuristic-instrumental (guidelines for contextualised action and intervention), practical-phronetic (deliberation of value-rational aspects of means and ends), and developmental-emancipatory (deliberation of issues of power, self-determination, and growth) aspects. Its goal is the production of orientation knowledge for educational practise. The thesis provides an analysis, argumentation, and normative claim on why the development of learning activity should be turned into an object of individual|collective inquiry and intentional change in higher education, and why the current state of affairs in higher education actually impedes such a development. It argues for a decisive shift of attention to the intentional emancipation and further development of learning activity as an important cultural instrument for human (self-)production within the digital transformation. The thesis also attempts an in-depth exploration of what type of methodological rationale can actually be applied to an object of inquiry (developing learning activity) that is at the same time conceptualised as an object of intentional change within the ongoing digital transformation. The result of this retrospective reflection is the formulation of “optimally incomplete” guidelines for educational R&D practise that shares the practicalphronetic (value related) and developmental-emancipatory (power related) orientations that had been driving the overall inquiry. In addition, the thesis formulates the instrumental-heuristic knowledge claim that the conceptual instruments that were adapted and validated in the context of a series of intervention studies provide means to effectively intervene into existing practise in higher education to support the necessary development of (increasingly emancipated) networked learning activity. It suggests that digital networked instruments (tools and services) generally should be considered and treated as transient elements within critical systemic intervention research in higher education. It further argues for the predominant use of loosely-coupled, digital networked instruments that allow for individual|collective ownership, control, (co-)production, and re-use in other contexts and for other purposes. Since the range of digital instrumentation options is continuously expanding and currently shows no signs of an imminent slow-down or consolidation, individual and collective exploration and experimentation of this realm needs to be systematically incorporated into higher education practise.

Modeling and Parameter Estimation of Double-Star Permanent Magnet Synchronous Machines

The power rating of wind turbines is constantly increasing; however, keeping the voltage rating at the low-voltage level results in high kilo-ampere currents. An alternative for increasing the power levels without raising the voltage level is provided by multiphase machines. Multiphase machines are used for instance in ship propulsion systems, aerospace applications, electric vehicles, and in other high-power applications including wind energy conversion systems. A machine model in an appropriate reference frame is required in order to design an efficient control for the electric drive. Modeling of multiphase machines poses a challenge because of the mutual couplings between the phases. Mutual couplings degrade the drive performance unless they are properly considered. In certain multiphase machines there is also a problem of high current harmonics, which are easily generated because of the small current path impedance of the harmonic components. However, multiphase machines provide special characteristics compared with the three-phase counterparts: Multiphase machines have a better fault tolerance, and are thus more robust. In addition, the controlled power can be divided among more inverter legs by increasing the number of phases. Moreover, the torque pulsation can be decreased and the harmonic frequency of the torque ripple increased by an appropriate multiphase configuration. By increasing the number of phases it is also possible to obtain more torque per RMS ampere for the same volume, and thus, increase the power density. In this doctoral thesis, a decoupled d–q model of double-star permanent-magnet (PM) synchronous machines is derived based on the inductance matrix diagonalization. The double-star machine is a special type of multiphase machines. Its armature consists of two three-phase winding sets, which are commonly displaced by 30 electrical degrees. In this study, the displacement angle between the sets is considered a parameter. The diagonalization of the inductance matrix results in a simplified model structure, in which the mutual couplings between the reference frames are eliminated. Moreover, the current harmonics are mapped into a reference frame, in which they can be easily controlled. The work also presents methods to determine the machine inductances by a finite-element analysis and by voltage-source inverters on-site. The derived model is validated by experimental results obtained with an example double-star interior PM (IPM) synchronous machine having the sets displaced by 30 electrical degrees. The derived transformation, and consequently, the decoupled d–q machine model, are shown to model the behavior of an actual machine with an acceptable accuracy. Thus, the proposed model is suitable to be used for the model-based control design of electric drives consisting of double-star IPM synchronous machines.

Mathematical modeling and optimal control of malaria

Malaria continues to infect millions and kill hundreds of thousands of people worldwide each year, despite over a century of research and attempts to control and eliminate this infectious disease. Challenges such as the development and spread of drug resistant malaria parasites, insecticide resistance to mosquitoes, climate change, the presence of individuals with subpatent malaria infections which normally are asymptomatic and behavioral plasticity in the mosquito hinder the prospects of malaria control and elimination. In this thesis, mathematical models of malaria transmission and control that address the role of drug resistance, immunity, iron supplementation and anemia, immigration and visitation, and the presence of asymptomatic carriers in malaria transmission are developed. A within-host mathematical model of severe Plasmodium falciparum malaria is also developed. First, a deterministic mathematical model for transmission of antimalarial drug resistance parasites with superinfection is developed and analyzed. The possibility of increase in the risk of superinfection due to iron supplementation and fortification in malaria endemic areas is discussed. The model results calls upon stakeholders to weigh the pros and cons of iron supplementation to individuals living in malaria endemic regions. Second, a deterministic model of transmission of drug resistant malaria parasites, including the inflow of infective immigrants, is presented and analyzed. The optimal control theory is applied to this model to study the impact of various malaria and vector control strategies, such as screening of immigrants, treatment of drug-sensitive infections, treatment of drug-resistant infections, and the use of insecticide-treated bed nets and indoor spraying of mosquitoes. The results of the model emphasize the importance of using a combination of all four controls tools for effective malaria intervention. Next, a two-age-class mathematical model for malaria transmission with asymptomatic carriers is developed and analyzed. In development of this model, four possible control measures are analyzed: the use of long-lasting treated mosquito nets, indoor residual spraying, screening and treatment of symptomatic, and screening and treatment of asymptomatic individuals. The numerical results show that a disease-free equilibrium can be attained if all four control measures are used. A common pitfall for most epidemiological models is the absence of real data; model-based conclusions have to be drawn based on uncertain parameter values. In this thesis, an approach to study the robustness of optimal control solutions under such parameter uncertainty is presented. Numerical analysis of the optimal control problem in the presence of parameter uncertainty demonstrate the robustness of the optimal control approach that: when a comprehensive control strategy is used the main conclusions of the optimal control remain unchanged, even if inevitable variability remains in the control profiles. The results provide a promising framework for the design of cost-effective strategies for disease control with multiple interventions, even under considerable uncertainty of model parameters. Finally, a separate work modeling the within-host Plasmodium falciparum infection in humans is presented. The developed model allows re-infection of already-infected red blood cells. The model hypothesizes that in severe malaria due to parasite quest for survival and rapid multiplication, the Plasmodium falciparum can be absorbed in the already-infected red blood cells which accelerates the rupture rate and consequently cause anemia. Analysis of the model and parameter identifiability using Markov chain Monte Carlo methods is presented.

Spectral Analysis of Symmetric and Anti-Symmetric Pairwise Kernels

This work investigates theoretical properties of symmetric and anti-symmetric kernels. First chapters give an overview of the theory of kernels used in supervised machine learning. Central focus is on the regularized least squares algorithm, which is motivated as a problem of function reconstruction through an abstract inverse problem. Brief review of reproducing kernel Hilbert spaces shows how kernels define an implicit hypothesis space with multiple equivalent characterizations and how this space may be modified by incorporating prior knowledge. Mathematical results of the abstract inverse problem, in particular spectral properties, pseudoinverse and regularization are recollected and then specialized to kernels. Symmetric and anti-symmetric kernels are applied in relation learning problems which incorporate prior knowledge that the relation is symmetric or anti-symmetric, respectively. Theoretical properties of these kernels are proved in a draft this thesis is based on and comprehensively referenced here. These proofs show that these kernels can be guaranteed to learn only symmetric or anti-symmetric relations, and they can learn any relations relative to the original kernel modified to learn only symmetric or anti-symmetric parts. Further results prove spectral properties of these kernels, central result being a simple inequality for the the trace of the estimator, also called the effective dimension. This quantity is used in learning bounds to guarantee smaller variance.

Utilization of Knowledge Management in Business Process Modeling and Process Improvements

Tutkimuksen tavoitteena on tutkia telekommunikaatioalalla toimivan kohdeyrityksen ohjelmistojen toimitusprosessia° Tutkimus keskittyy mallintamaan toimitusprosessin, määrittelemään roolit ja vastuualueet, havaitsemaan ongelmakohdat ja ehdottamaan prosessille kehityskohteita. Näitä tavoitteita tarkastellaan teoreettisten prosessimallinnustekniikoiden ja tietojohtamisen SECI-prosessikehyksen läpi. Tärkein tiedonkeruun lähde oli haastatteluihin perustuva tutkimus, johon osallistuvat kaikki kohdeprosessiin kuuluvat yksiköt. Mallinnettu toimitusprosessi antoi kohdeyritykselle paremman käsityksen tarkasteltavasta prosessista ja siinä toimivien yksiköiden rooleistaja vastuualueista. Parannusehdotuksia olivat tiedonjaon kanavoinnin määritteleminen, luottamuksen ja sosiaalisten verkostojen parantaminen, ja tietojohtamisen laajamittainen implementointi.

Modeling and Synthesis of Tracking Control for the Belt Drive System

Usingof belt for high precision applications has become appropriate because of the rapid development in motor and drive technology as well as the implementation of timing belts in servo systems. Belt drive systems provide highspeed and acceleration, accurate and repeatable motion with high efficiency, long stroke lengths and low cost. Modeling of a linear belt-drive system and designing its position control are examined in this work. Friction phenomena and position dependent elasticity of the belt are analyzed. Computer simulated results show that the developed model is adequate. The PID control for accurate tracking control and accurate position control is designed and applied to the real test setup. Both the simulation and the experimental results demonstrate that the designed controller meets the specified performance specifications.

Analysis of torque and speed ripple producing non-idealities of frequency converters in electric drives

Electric motors driven by adjustable-frequency converters may produce periodic excitation forces that can cause torque and speed ripple. Interaction with the driven mechanical system may cause undesirable vibrations that affect the system performance and lifetime. Direct drives in sensitive applications, such as elevators or paper machines, emphasize the importance of smooth torque production. This thesis analyses the non-idealities of frequencyconverters that produce speed and torque ripple in electric drives. The origin of low order harmonics in speed and torque is examined. It is shown how different current measurement error types affect the torque. As the application environment, direct torque control (DTC) method is applied to permanent magnet synchronous machines (PMSM). A simulation model to analyse the effect of the frequency converter non-idealities on the performance of the electric drives is created. Themodel enables to identify potential problems causing torque vibrations and possibly damaging oscillations in electrically driven machine systems. The model is capable of coupling with separate simulation software of complex mechanical loads. Furthermore, the simulation model of the frequency converter's control algorithm can be applied to control a real frequency converter. A commercial frequencyconverter with standard software, a permanent magnet axial flux synchronous motor and a DC motor as the load are used to detect the effect of current measurement errors on load torque. A method to reduce the speed and torque ripple by compensating the current measurement errors is introduced. The method is based on analysing the amplitude of a selected harmonic component of speed as a function oftime and selecting a suitable compensation alternative for the current error. The speed can be either measured or estimated, so the compensation method is applicable also for speed sensorless drives. The proposed compensation method is tested with a laboratory drive, which consists of commercial frequency converter hardware with self-made software and a prototype PMSM. The speed and torque rippleof the test drive are reduced by applying the compensation method. In addition to the direct torque controlled PMSM drives, the compensation method can also beapplied to other motor types and control methods.

Predicting diffusion of innovations with self-organisation and machine learning

The main subject of this master's thesis was predicting diffusion of innovations. The prediction was done in a special case: product has been available in some countries, and based on its diffusion in those countries the prediction is done for other countries. The prediction was based on finding similar countries with Self-Organizing Map~(SOM), using parameters of countries. Parameters included various economical and social key figures. SOM was optimised for different products using two different methods: (a) by adding diffusion information of products to the country parameters, and (b) by weighting the country parameters based on their importance for the diffusion of different products. A novel method using Differential Evolution (DE) was developed to solve the latter, highly non-linear optimisation problem. Results were fairly good. The prediction method seems to be on a solid theoretical foundation. The results based on country data were good. Instead, optimisation for different products did not generally offer clear benefit, but in some cases the improvement was clearly noticeable. The weights found for the parameters of the countries with the developed SOM optimisation method were interesting, and most of them could be explained by properties of the products.