Wood as a model material for medical biomaterials. In vivo and in vitro studies with bone and Betula pubescens Ehrh

Novel biomaterials are needed to fill the demand of tailored bone substitutes required by an ever‐expanding array of surgical procedures and techniques. Wood, a natural fiber composite, modified with heat treatment to alter its composition, may provide a novel approach to the further development of hierarchically structured biomaterials. The suitability of wood as a model biomaterial as well as the effects of heat treatment on the osteoconductivity of wood was studied by placing untreated and heat‐treated (at 220 C , 200 degrees and 140 degrees for 2 h) birch implants (size 4 x 7mm) into drill cavities in the distal femur of rabbits. The follow‐up period was 4, 8 and 20 weeks in all in vivo experiments. The flexural properties of wood as well as dimensional changes and hydroxyl apatite formation on the surface of wood (untreated, 140 degrees C and 200 degrees C heat‐treated wood) were tested using 3‐point bending and compression tests and immersion in simulated body fluid. The effect of premeasurement grinding and the effect of heat treatment on the surface roughness and contour of wood were tested with contact stylus and non‐contact profilometry. The effects of heat treatment of wood on its interactions with biological fluids was assessed using two different test media and real human blood in liquid penetration tests. The results of the in vivo experiments showed implanted wood to be well tolerated, with no implants rejected due to foreign body reactions. Heat treatment had significant effects on the biocompatibility of wood, allowing host bone to grow into tight contact with the implant, with occasional bone ingrowth into the channels of the wood implant. The results of the liquid immersion experiments showed hydroxyl apatite formation only in the most extensively heat‐treated wood specimens, which supported the results of the in vivo experiments. Parallel conclusions could be drawn based on the results of the liquid penetration test where human blood had the most favorable interaction with the most extensively heat‐treated wood of the compared materials (untreated, 140 degrees C and 200 degrees C heat‐treated wood). The increasing biocompatibility was inferred to result mainly from changes in the chemical composition of wood induced by the heat treatment, namely the altered arrangement and concentrations of functional chemical groups. However, the influence of microscopic changes in the cell walls, surface roughness and contour cannot be totally excluded. The heat treatment was hypothesized to produce a functional change in the liquid distribution within wood, which could have biological relevance. It was concluded that the highly evolved hierarchical anatomy of wood could yield information for the future development of bulk bone substitutes according to the ideology of bioinspiration. Furthermore, the results of the biomechanical tests established that heat treatment alters various biologically relevant mechanical properties of wood, thus expanding the possibilities of wood as a model material, which could include e.g. scaffold applications, bulk bone applications and serving as a tool for both mechanical testing and for further development of synthetic fiber reinforced composites.

PET Imaging of Osteomyelitis. Feasibility of 18F-FDG, 68Ga-Chloride and 68Ga-DOTAVAP-P1 Tracers in Staphylococcal Bone Infections

Due to technical restrictions of the database system the title of the thesis does not show corretly on this page. Numbers in the title are in superscript. Please see the PDF-file for correct title. ---- Osteomyelitis is a progressive inflammatory disease of bone and bone marrow that results in bone destruction due to an infective microorganism, most frequently Staphylococcus aureus. Orthopaedic concern relates to the need for reconstructive and trauma-related surgical procedures in the fast grow¬ing population of fragile, aged patients, who have an increased susceptibility to surgical site infections. Depending on the type of osteomyelitis, infection may be acute or a slowly progressing, low-grade infection. Peri-implant infections lead to implant loosening. The emerging antibiotic resistance of com¬mon pathogens further complicates the situation. With current imaging methods, significant limitations exist in the diagnosing of osteomyelitis and implant-related infections. Positron emission tomography (PET) with a glucose analogue, 18F-fluoro¬deoxyglucose (18F-FDG), seems to facilitate a more accurate diagnosis of chronic osteomyelitis. The method is based on the increased glucose consumption of activated inflammatory cells. Unfortunately, 18F-FDG accumulates also in sterile inflammation regions and causes false-positive findings, for exam¬ple, due to post-operative healing processes. Therefore, there is a clinical need for new, more infection-specific tracers. In addition, it is still unknown why 18F-FDG PET imaging is less accurate in the detec¬tion of periprosthetic joint infections, most frequently due to Staphylococcus epidermidis. This doctoral thesis focused on testing novel PET tracers (68Ga-chloride and 68Ga-DOTAVAP-P1) for early detections of bone infections and evaluated the role of pathogen-related factors in the appli¬cations of 18F-FDG PET in the diagnostics of bone infections. For preclinical models of S. epidermidis and S. aureus bone/implant infections, the significance of the causative pathogen was studied with respect to 18F-FDG uptake. In a retrospective analysis of patients with confirmed bone infections, the significance of the presence or absence of positive bacterial cultures on 18F-FDG uptake was evalu¬ated. 18F-FDG and 68Ga-chloride resulted in a similar uptake in S. aureus osteomyelitic bones. However, 68Ga-chloride did not show uptake in healing bones, and therefore it may be a more-specific tracer in the early post-operative or post-traumatic phase. 68Ga-DOTAVAP-P1, a novel synthetic peptide bind¬ing to vascular adhesion protein 1 (VAP-1), was able to detect the phase of inflammation in healing bones, but the uptake of the tracer was elevated also in osteomyelitis. Low-grade peri-implant infec¬tions due to S. epidermidis were characterized by a low uptake of 18F-FDG, which reflects the virulence of the causative pathogen and the degree of leukocyte infiltration. In the clinical study, no relationship was found between the level of 18F-FDG uptake and the presence of positive or negative bacterial cul¬tures. Thus 18F-FDG PET may help to confirm metabolically active infection process in patients with culture-negative, histologically confirmed, low-grade osteomyelitis.

Development of Craniofacial Bone Defect Reconstruction Implant Based on Fibre-Reinforced Composite with Photopolymerisable Resin Systems. Experimental studies in vitro and in vivo.

Reconstruction of defects in the craniomaxillofacial (CMF) area has mainly been based on bone grafts or metallic fixing plates and screws. Particularly in the case of large calvarial and/or craniofacial defects caused by trauma, tumours or congenital malformations, there is a need for reliable reconstruction biomaterials, because bone grafts or metallic fixing systems do not completely fulfill the criteria for the best possible reconstruction methods in these complicated cases. In this series of studies, the usability of fibre-reinforced composite (FRC) was studied as a biostable, nonmetallic alternative material for reconstructing artificially created bone defects in frontal and calvarial areas of rabbits. The experimental part of this work describes the different stages of the product development process from the first in vitro tests with resin-impregnated fibrereinforced composites to the in vivo animal studies, in which this FRC was tested as an implant material for reconstructing different size bone defects in rabbit frontal and calvarial areas. In the first in vitro study, the FRC was polymerised in contact with bone or blood in the laboratory. The polymerised FRC samples were then incubated in water, which was analysed for residual monomer content by using high performance liquid chromatography (HPLC). It was found that this in vitro polymerisation in contact with bone and blood did not markedly increase the residual monomer leaching from the FRC. In the second in vitro study, different adhesive systems were tested in fixing the implant to bone surface. This was done to find an alternative implant fixing system to screws and pins. On the basis of this study, it was found that the surface of the calvarial bone needed both mechanical and chemical treatments before the resinimpregnated FRC could be properly fixed onto it. In three animal studies performed with rabbit frontal bone defects and critical size calvarial bone defect models, biological responses to the FRC implants were evaluated. On the basis of theseevaluations, it can be concluded that the FRC, based on E-glass (electrical glass) fibres forming a porous fibre veil enables the ingrowth of connective tissues to the inner structures of the material, as well as the bone formation and mineralization inside the fibre veil. Bone formation could be enhanced by using bioactive glass granules fixed to the FRC implants. FRC-implanted bone defects healed partly; no total healing of defects was achieved. Biological responses during the follow-up time, at a maximum of 12 weeks, to resin-impregnated composite implant seemed to depend on the polymerization time of the resin matrix of the FRC. Both of the studied resin systems used in the FRC were photopolymerised and the heat-induced postpolymerisation was used additionally.

Non-resorbable glass fibre-reinforced composite with porous surface as bone substitute material: Experimental studies in vitro and in vivo focused on bone-implant interface

The development of load-bearing osseous implant with desired mechanical and surface properties in order to promote incorporation with bone and to eliminate risk of bone resorption and implant failure is a very challenging task. Bone formation and resoption processes depend on the mechanical environment. Certain stress/strain conditions are required to promote new bone growth and to prevent bone mass loss. Conventional metallic implants with high stiffness carry most of the load and the surrounding bone becomes virtually unloaded and inactive. Fibre-reinforced composites offer an interesting alternative to metallic implants, because their mechanical properties can be tailored to be equal to those of bone, by the careful selection of matrix polymer, type of fibres, fibre volume fraction, orientation and length. Successful load transfer at bone-implant interface requires proper fixation between the bone and implant. One promising method to promote fixation is to prepare implants with porous surface. Bone ingrowth into porous surface structure stabilises the system and improves clinical success of the implant. The experimental part of this work was focused on polymethyl methacrylate (PMMA) -based composites with dense load-bearing core and porous surface. Three-dimensionally randomly orientated chopped glass fibres were used to reinforce the composite. A method to fabricate those composites was developed by a solvent treatment technique and some characterisations concerning the functionality of the surface structure were made in vitro and in vivo. Scanning electron microscope observations revealed that the pore size and interconnective porous architecture of the surface layer of the fibre-reinforced composite (FRC) could be optimal for bone ingrowth. Microhardness measurements showed that the solvent treatment did not have an effect on the mechanical properties of the load-bearing core. A push-out test, using dental stone as a bone model material, revealed that short glass fibre-reinforced porous surface layer is strong enough to carry load. Unreacted monomers can cause the chemical necrosis of the tissue, but the levels of leachable resisidual monomers were considerably lower than those found in chemically cured fibre-reinforced dentures and in modified acrylic bone cements. Animal experiments proved that surface porous FRC implant can enhance fixation between bone and FRC. New bone ingrowth into the pores was detected and strong interlocking between bone and the implant was achieved.

Acid-base Balance and Oxidative Metabolism in Calcified Tissues

The calcified tissues, comprising bone and cartilage, are metabolically active tissues that bind and release calcium, bicarbonate and other substances according to systemic needs. Understanding the regulation of cellular metabolism in bone and cartilage is an important issue, since a link between the metabolism and diseases of these tissues is clear. An essential element in the function of bone-resorbing osteoclasts, namely regulation of bicarbonate transport, has not yet been thoroughly studied. Another example of an important but at the same time fairly unexplored subject of interest in this field is cartilage degeneration, an important determinant for development of osteoarthritis. The link between this and oxidative metabolism has rarely been studied. In this study, we have investigated the significance of bicarbonate transport in osteoclasts. We found that osteoclasts possess several potential proteins for bicarbonate transport, including carbonic anhydrase IV and XIV, and an electroneutral bicarbonate co-transporter NBCn1. We have also shown that inhibiting the function of these proteins has a significant impact on bone resorption and osteoclast morphology. Furthermore, we have explored oxidative metabolism in chondrocytes and found that carbonic anhydrase III (CA III), a protein linked to the prevention of protein oxidation in muscle cells, is also present in mouse chondrocytes, where its expression correlates with the presence of reactive oxygen species. Thus, our study provides novel information on the regulation of cellular metabolism in calcified tissues.

The Role of Integrins in Enterovirus Infections and in Metastasis of Cancer

Integrins are a family of transmembrane glycoproteins, composed of two different subunits (alpha and beta). Altered expression of integrins in tumor cells contributes to metastasis tendency by influencing on the cells‟ attachment to adjacent cells and their migration. Viral pathogens, including certain enteroviruses, use integrins as receptors. Enteroviruses have also been suggested to be involved in the etiopathogenesis of type 1 diabetes. The study focuses on the role of integrins in the pathogenesis of metastasis to cortical bone and on type 1 diabetes (T1D) and echovirus 1 infection. In the first part of the thesis, the role of different integrins in the initial attachment of MDA-MD-231 breast cancer cells to bovine cortical bone disks was studied. A close correlation between alpha2beta1 and alpha3beta1 integrin receptor expression and the capability of the tumor to attach to bone were observed. In the second part, a possible correlation between susceptibility to enterovirus infections in diabetic children and differences in enterovirus receptor genes, including certain integrins, was investigated. In parallel, virus-specific neutralizing antibodies and diabetic risk alleles were studied. In the diabetic group, an amino acid change was detected in the polio virus receptor and the neutralizing antibody titers against echovirus 30 were lower. However, to obtain statistically sustainable results, a larger number of individuals should be analyzed. Echovirus 1 (EV1) enters cells by attaching to the alpha2I domain of the alpha2beta1 integrin. In the third part EV1 was shown to attach to a chimeric receptor construct of the transferrin receptor and the alpha2I domain and to enter cells through clathrin-mediated endocytosis that is normally not used by the virus. The chimeric receptor was recycled to the plasma membrane, whereas the virus remained in intracellular vesicles. The virus replication cycle was initiated in these cells, suggesting that evolution pressure could possibly cause the virus to evolve to use a different entry mechanism. Moreover, a cDNA microarray analysis of host gene expression during EV1 replication showed that 0.53% of the total genes, including several immediate early genes, were differently expressed.

Markers of Bone Turnover In Preclinical Development of Drugs for Skeletal Diseases

Skeletal tissue is constantly remodeled in a process where osteoclasts resorb old bone and osteoblasts form new bone. Balance in bone remodeling is related to age, gender and genetic factors, but also many skeletal diseases, such as osteoporosis and cancer-induced bone metastasis, cause imbalance in bone turnover and lead to decreased bone mass and increased fracture risk. Biochemical markers of bone turnover are surrogates for bone metabolism and may be used as indicators of the balance between bone resorption and formation. They are released during the remodeling process and can be conveniently and reliably measured from blood or urine by immunoassays. Most commonly used bone formation markers include N-terminal propeptides of type I collagen (PINP) and osteocalcin, whereas tartrate-resistant acid phosphatase isoform 5b (TRACP 5b) and C-terminal cross-linked telopeptide of type I collagen (CTX) are common resorption markers. Of these, PINP has been, until recently, the only marker not commercially available for preclinical use. To date, widespread use of bone markers is still limited due to their unclear biological significance, variability, and insufficient evidence of their prognostic value to reflect long term changes. In this study, the feasibility of bone markers as predictors of drug efficacy in preclinical osteoporosis models was elucidated. A non-radioactive PINP immunoassay for preclinical use was characterized and validated. The levels of PINP, N-terminal mid-fragment of osteocalcin, TRACP 5b and CTX were studied in preclinical osteoporosis models and the results were compared with the results obtained by traditional analysis methods such as histology, densitometry and microscopy. Changes in all bone markers at early timepoints correlated strongly with the changes observed in bone mass and bone quality parameters at the end of the study. TRACP 5b correlated strongly with the osteoclast number and CTX correlated with the osteoclast activity in both in vitro and in vivo studies. The concept “resorption index” was applied to the relation of CTX/TRACP 5b to describe the mean osteoclast activity. The index showed more substantial changes than either of the markers alone in the preclinical osteoporosis models used in this study. PINP was strongly associated with bone formation whereas osteocalcin was associated with both bone formation and resorption. These results provide novel insight into the feasibility of PINP, osteocalcin, TRACP 5b and CTX as predictors of drug efficacy in preclinical osteoporosis models. The results support clinical findings which indicate that short-term changes of these markers reflect long-term responses in bone mass and quality. Furthermore, this information may be useful when considering cost-efficient and clinically predictive drug screening and development assays for mining new drug candidates for skeletal diseases.

Gammakuvaus eli skintigrafia hevosen ontumatutkimuksessa Osa 2

Summary: Scintigraphy in lameness examination of the horse : part 2 : imaging of bone and muscle injuries

Kokeellisen moodianalyysin hyödyntäminen sääriluun lujuuden määrittämisessä

Diplomityö tehtiin Lappeenrannan teknillisen yliopiston konetekniikan laitokselle. Diplomityö on osa teknillisen yliopiston biomekaanista tutkimusta, jonka tarkoituksena on mallintaa ihmisen tuki- ja liikuntaelimistön toimintaa. Työssä pyrittiin selvittämään, voitaisiinko sääriluuhun kohdistetun mekaanisen herätteen aiheuttamaa värähtelyvastetta analysoimalla saada tietoa luun ominaistaajuuksista ja lujuudesta. Tietoa voitaisiin käyttää esimerkiksi ostoporoosiriskin arvioinnissa sekä ihmiskehon osien toimintaa kuvaavien simulointimallien verifioinnissa. Mittauslaitteistona käytettiin Brüel & Kjær-moodianalyysilaitteistoa. Laitteistokokonaisuuteen kuuluivat herätevasara, elektromagneettinen täristin, voima-anturi, kaksi kiihtyvyysmitta-anturia sekä PulseLab 2.0 –ohjelmistolla varustettu PC-laitteisto. Tulosten jatkoanalyysi suoritettiin MathWorks yhtiön MatLab v 4.0 -ohjelmistolla. Työssä esitellyn mittaustavan ja -laitteiston todettiin soveltuvan sääriluun värähtelyvasteen mittaamiseen. Mittaustulokset eri mittauskertojen välillä samalla henkilöllä ovat yhtenevät. Tutkimuksen tulosten perusteella ei voida osoittaa luun värähtelyvasteen ja lujuuden välistä suoraa korrelaatiota.

MicroRNAs as novel regulators of skeletal homeostasis

The human skeleton is composed of bone and cartilage. The differentiation of bone and cartilage cells from their bone marrow progenitors is regulated by an intrinsic network of intracellular and extracellular signaling molecules. In addition, cells coordinate their differentiation and function through reciprocal cell‐to‐cell interactions. MicroRNAs (miRNAs) are small, single‐stranded RNA molecules that inhibit protein translation by binding to messenger RNAs (mRNAs). Recent evidence demonstrates the involvement of miRNAs in multiple biological processes. However, their role in skeletal development and bone remodeling is still poorly understood. The aim of this thesis was to elucidate miRNA‐mediated gene regulation in bone and cartilage cells, namely in osteoblasts, osteoclasts, chondrocytes and bone marrow adipocytes. Comparison of miRNA expression during osteogenic and chondrogenic differentiation of bone marrow‐derived mesenchymal stem cells (MSCs) revealed several miRNAs with substantial difference between bone and cartilage cells. These miRNAs were predicted to target genes essentially involved in MSC differentiation. Three miRNAs, miR‐96, miR‐124 and miR‐199a, showed marked upregulation upon osteogenic, chondrogenic or adipogenic differentiation. Based on functional studies, these miRNAs regulate gene expression in MSCs and may thereby play a role in the commitment and/or differentiation of MSCs. Characterization of miRNA expression during osteoclastogenesis of mouse bone marrow cells revealed a unique expression pattern for several miRNAs. Potential targets of the differentially expressed miRNAs included many molecules essentially involved in osteoclast differentiation. These results provide novel insights into the expression and function of miRNAs during the differentiation of bone and cartilage cells. This information may be useful for the development of novel stem cell‐based treatments for skeletal defects and diseases.