Fiber Laser Cutting of Mild Steel

Fiber laser for materials processing have undergone a rapid development in the pastseveral years. As fiber laser provides a combination of high beam quality and awavelength that is easily absorbed by metal surfaces, the named future laser isexpected to challenge the CO2 and Nd:YAG lasers in the area of metal cutting. This thesis studied the performance of fiber laser cutting mild steel. In the literature review part, it introduced the laser cutting principle and the principle of fiber laser including the newest development of fiber laser cuttingtechnology. Because the fiber laser cutting mild steel is a very young technology, a preliminary test was made in order to investigate effect of the cutting parameters on cut quality. Then the formal fiber laser cutting experiment was madeby using 3 mm thickness S355 steel with oxygen as assistant gas. The experimentwas focused on the cut quality with maximum cutting speed and minimum oxygen gas pressure. And the cut quality is mainly decided by the kerf width, perpendicularity tolerance, surface roughness and striation patterns. After analysis the cutting result, several conclusions were made. Although the best result got in the experiment is not perfect as predicted, the whole result of the test can be accepted. Compared with CO2 laser, a higher cutting speed was achieved by fiber laser with very low oxygen gas pressure. A further improvement about the cutting quality might be possible by proper selection of process parameters. And in order to investigate the cutting performance more clearly, a future study about cutting different thickness mild steel and different shape was recommended.

Development of Paperboard Forming Tools with a Focus on Intelligent Manufacturing

Tämä diplomityö käsittelee kartonginmuovaukseen käytettävien puristintyökalujen kehittämistä. Työntavoitteina oli kehittää työkalutekniikan suunnittelua ja valmistusta edullisemmaksi, nopeammaksi ja työkaluja toiminnoiltaan tehokkaammiksi. Työn tuli sisältää myös ohjeet työkalujen suunnittelemiseksi ja valmistamiseksi jatkoa ajatellen. Työn aikana selvitettiin mahdollisia työkalurakennevaihtoehtoja, valmistusmateriaaleja sekä niiden käsittelymenetelmiä ja lastuamista sekä sen tarjoamia mahdollisuuksia valmistusmenetelmänä. Työkalupari suunniteltiin modulaariseksi siten, että uusia työkaluja varten vain osa komponenteista täytyy valmistaa uudelleen, samalla työkalun osien lukumäärää pienennettiin merkittävästi. Valmistusmateriaaliksi valittiin hyvin lastuttava työkaluteräs ja sen koneistaminen tapahtui vaakakaraisessa koneistuskeskuksessa. Työn loppuvaiheessa työkalukokonaisuudelle tehtiin kustannuslaskelma jaoteltuna eri työvaiheille sekä komponenteittain. Työkalu asennettiin puristimeen ja sille suoritettiin käyttötestaus. Työn aikana karttuneen kokemuksen sekä koekäytön perusteella tehtiin jatkokehitysehdotuksia.

Koneinvestoinnin suunnittelu valmistavaan teollisuuteen

Tämän diplomityön tavoitteena oli tutustua ohutlevyjen nykyaikaisiin koneellisiin leikkausmenetelmiin ja tutkia niiden soveltuvuutta yrityksen tarpeisiin. Kohdeyrityksessä investoinnin tarve jakautui tuottavuusinvestoinnin, korvausinvestoinnin ja strategisen investoinnin kesken. Tavoitteena oli luoda investointipolku, jonka avulla poissuljettiin menetelmät, jotka eivät soveltuneet yrityksen tuotantoon. Työn kirjallisuusosuudessa tarkastellaan teoriatietoja, jotka liittyvät yleisesti nykyaikaisiin ohutlevyjen leikkausmenetelmiin sekä investointiprojektin suunnitteluun ja toteutuksen teoriaan. Lisäksi käsitellään investointeihin liittyviä kannattavuus- ja kustannuslaskennan perusperiaatteita. Työn empiirisessä osassa selvitettiin yrityksen ohutlevyosien valmistuksen periaatteita nykytila-analyysin avulla. Tämän perusteella määritettiin nykyaikaisista markkinoilla olevista menetelmistä yritykselle soveltuvin. Tutkimuksen perusteella laserleikkaus oli menetelmistä soveltuvin. Perusinvestoinniltaan laser oli vaihtoehtoisista menetelmistä kallein, mutta se soveltui käytettävyyden, tehokkuuden, joustavuuden ja muiden ominaisuuksiensa perusteella parhaiten tuotannon tarpeisiin. Työn merkittävimmät tulokset osoittivat, että investoinnin kannattavuus riippui koneelle saatavasta käyttösuhteesta. Uusien koneiden tehokkuus lyhentäisi tuotannon läpimenoaikoja, mutta ilman riittävää kapasiteetin käyttöastetta kappaleiden omakustannusarvo nousisi. Lopputulokset ja suositukset on esitetty työn lopussa.

Laser Cutting of Austenitic Stainless Steel with a High Quality Laser Beam

The thin disk and fiber lasers are new solid-state laser technologies that offer a combinationof high beam quality and a wavelength that is easily absorbed by metal surfacesand are expected to challenge the CO2 and Nd:YAG lasers in cutting of metals ofthick sections (thickness greater than 2mm). This thesis studied the potential of the disk and fiber lasers for cutting applications and the benefits of their better beam quality. The literature review covered the principles of the disk laser, high power fiber laser, CO2 laser and Nd:YAG laser as well as the principle of laser cutting. The cutting experiments were made with thedisk, fiber and CO2 lasers using nitrogen as an assist gas. The test material was austenitic stainless steel of sheet thickness 1.3mm, 2.3mm, 4.3mm and 6.2mm for the disk and fiber laser cutting experiments and sheet thickness of 1.3mm, 1.85mm, 4.4mm and 6.4mm for the CO2 laser cutting experiments. The experiments focused on the maximum cutting speeds with appropriate cut quality. Kerf width, cutedge perpendicularity and surface roughness were the cut characteristics used to analyze the cut quality. Attempts were made to draw conclusions on the influence of high beam quality on the cutting speed and cut quality. The cutting speeds were enormous for the disk and fiber laser cutting experiments with the 1.3mm and 2.3mm sheet thickness and the cut quality was good. The disk and fiber laser cutting speeds were lower at 4.3mm and 6.2mm sheet thickness but there was still a considerable percentage increase in cutting speeds compared to the CO2 laser cutting speeds at similar sheet thickness. However, the cut quality for 6.2mm thickness was not very good for the disk and fiber laser cutting experiments but could probably be improved by proper selection of cutting parameters.

Performance of high power fibre laser cutting of thick-section steel and mediumsection aluminium

Cutting of thick section stainless steel and mild steel, and medium section aluminium using the high power ytterbium fibre laser has been experimentally investigated in this study. Theoretical models of the laser power requirement for cutting of a metal workpiece and the melt removal rate were also developed. The calculated laser power requirement was correlated to the laser power used for the cutting of 10 mm stainless steel workpiece and 15 mm mild steel workpiece using the ytterbium fibre laser and the CO2 laser. Nitrogen assist gas was used for cutting of stainless steel and oxygen was used for mild steel cutting. It was found that the incident laser power required for cutting at a given cutting speed was lower for fibre laser cutting than for CO2 laser cutting indicating a higher absorptivity of the fibre laser beam by the workpiece and higher melting efficiency for the fibre laser beam than for the CO2 laser beam. The difficulty in achieving an efficient melt removal during high speed cutting of the 15 mmmild steel workpiece with oxygen assist gas using the ytterbium fibre laser can be attributed to the high melting efficiency of the ytterbium fibre laser. The calculated melt flow velocity and melt film thickness correlated well with the location of the boundary layer separation point on the 10 mm stainless steel cut edges. An increase in the melt film thickness caused by deceleration of the melt particles in the boundary layer by the viscous shear forces results in the flow separation. The melt flow velocity increases with an increase in assist gas pressure and cut kerf width resulting in a reduction in the melt film thickness and the boundary layer separation point moves closer to the bottom cut edge. The cut edge quality was examined by visual inspection of the cut samples and measurement of the cut kerf width, boundary layer separation point, cut edge squareness (perpendicularity) deviation, and cut edge surface roughness as output quality factors. Different regions of cut edge quality in 10 mm stainless steel and 4 mm aluminium workpieces were defined for different combinations of cutting speed and laserpower.Optimization of processing parameters for a high cut edge quality in 10 mmstainless steel was demonstrated

Investigation of Oxygen Cutting Process in Solid-State Welding

The oxygen cutting is a thermal cutting process, in which metal is heated locally up to its ignition temperature and burnt off by oxygen blast. Oxygen cutting can be used to remove upset metal of a hollow bar occurred due to solid-state welding process. The main goal of this research was to establish a connection between oxygen blasts and mass of metal removed and relate findings to production to suggest improvements to the current process. This master´s thesis describes the designing and building of a test rig for oxygen blowing measurements. It also contains all executed tests and test results, which were carried out. There are different cutting parameters which were studied as well as their effect on cutting process. The oxygen cutting process, used in solid-state welding process, can be improved by the test results.

Arsenic and heavy metal concentrations in agricultural soils in South Savo province

Selostus: Etelä-Savon viljelysmaan arseeni- ja raskasmetallipitoisuudet

Lihahygienialainsäädännön omavalvontasäädökset ja käytäntö Oy Snellman Ab:n teurastamossa ja leikkaamossa, osa I Osa 1 : Owncontrol directions in meat hygiene legislation and their practical implementation in the slaughterhouse and cutting plant of Snellman Ltd, part I

Summary: Owncontrol directions in meat hygiene legislation and their practical implementation in the slaughterhouse and cutting plant of Snellman Ltd, part I

Heavy-metal pollution and remediation of forest soil around the Harjavalta Cu-Ni smelter, in SW Finland

Abstract