Gas-liquid mass transfer in bubbly flow: Estimation of mass transfer, bubble size and reactor performance in various applications

Gas-liquid mass transfer is an important issue in the design and operation of many chemical unit operations. Despite its importance, the evaluation of gas-liquid mass transfer is not straightforward due to the complex nature of the phenomena involved. In this thesis gas-liquid mass transfer was evaluated in three different gas-liquid reactors in a traditional way by measuring the volumetric mass transfer coefficient (kLa). The studied reactors were a bubble column with a T-junction two-phase nozzle for gas dispersion, an industrial scale bubble column reactor for the oxidation of tetrahydroanthrahydroquinone and a concurrent downflow structured bed.The main drawback of this approach is that the obtained correlations give only the average volumetric mass transfer coefficient, which is dependent on average conditions. Moreover, the obtained correlations are valid only for the studied geometry and for the chemical system used in the measurements. In principle, a more fundamental approach is to estimate the interfacial area available for mass transfer from bubble size distributions obtained by solution of population balance equations. This approach has been used in this thesis by developing a population balance model for a bubble column together with phenomenological models for bubble breakage and coalescence. The parameters of the bubble breakage rate and coalescence rate models were estimated by comparing the measured and calculated bubble sizes. The coalescence models always have at least one experimental parameter. This is because the bubble coalescence depends on liquid composition in a way which is difficult to evaluate using known physical properties. The coalescence properties of some model solutions were evaluated by measuring the time that a bubble rests at the free liquid-gas interface before coalescing (the so-calledpersistence time or rest time). The measured persistence times range from 10 msup to 15 s depending on the solution. The coalescence was never found to be instantaneous. The bubble oscillates up and down at the interface at least a coupleof times before coalescence takes place. The measured persistence times were compared to coalescence times obtained by parameter fitting using measured bubble size distributions in a bubble column and a bubble column population balance model. For short persistence times, the persistence and coalescence times are in good agreement. For longer persistence times, however, the persistence times are at least an order of magnitude longer than the corresponding coalescence times from parameter fitting. This discrepancy may be attributed to the uncertainties concerning the estimation of energy dissipation rates, collision rates and mechanisms and contact times of the bubbles.

Development of filter media treatments for liquid filtration

Woven monofilament, multifilament, and spun yarn filter media have long been the standard media in liquid filtration equipment. While the energy for a solid-liquid separation process is determined by the engineering work, it is the interface between the slurry and the equipment - the filter media - that greatly affects the performance characteristics of the unit operation. Those skilled in the art are well aware that a poorly designed filter medium may endanger the whole operation, whereas well-performing filter media can make the operation smooth and economical. As the mineral and pulp producers seek to produce ever finer and more refined fractions of their products, it is becoming increasingly important to be able to dewater slurries with average particle sizes around 1 ¿m using conventional, high-capacity filtration equipment. Furthermore, the surface properties of the media must not allow sticky and adhesive particles to adhere to the media. The aim of this thesis was to test how the dirt-repellency, electrical resistance and highpressure filtration performance of selected woven filter media can be improved by modifying the fabric or yarn with coating, chemical treatment and calendering. The results achieved by chemical surface treatments clearly show that the woven media surface properties can be modified to achieve lower electrical resistance and improved dirt-repellency. The main challenge with the chemical treatments is the abrasion resistance and, while the experimental results indicate that the treatment is sufficiently permanent to resist standard weathering conditions, they may still prove to be inadequately strong in terms of actual use.From the pressure filtration studies in this work, it seems obvious that the conventional woven multifilament fabrics still perform surprisingly well against the coated media in terms of filtrate clarity and cake build-up. Especially in cases where the feed slurry concentration was low and the pressures moderate, the conventional media seemed to outperform the coated media. In the cases where thefeed slurry concentration was high, the tightly woven media performed well against the monofilament reference fabrics, but seemed to do worse than some of the coated media. This result is somewhat surprising in that the high initial specific resistance of the coated media would suggest that the media will blind more easily than the plain woven media. The results indicate, however, that it is actually the woven media that gradually clogs during the coarse of filtration. In conclusion, it seems obvious that there is a pressure limit above which the woven media looses its capacity to keep the solid particles from penetrating the structure. This finding suggests that for extreme pressures the only foreseeable solution is the coated fabrics supported by a strong enough woven fabric to hold thestructure together. Having said that, the high pressure filtration process seems to follow somewhat different laws than the more conventional processes. Based on the results, it may well be that the role of the cloth is most of all to support the cake, and the main performance-determining factor is a long life time. Measuring the pore size distribution with a commercially available porometer gives a fairly accurate picture of the pore size distribution of a fabric, but failsto give insight into which of the pore sizes is the most important in determining the flow through the fabric. Historically air, and sometimes water, permeability measures have been the standard in evaluating media filtration performance including particle retention. Permeability, however, is a function of a multitudeof variables and does not directly allow the estimation of the effective pore size. In this study a new method for estimating the effective pore size and open pore area in a densely woven multifilament fabric was developed. The method combines a simplified equation of the electrical resistance of fabric with the Hagen-Poiseuille flow equation to estimate the effective pore size of a fabric and the total open area of pores. The results are validated by comparison to the measured values of the largest pore size (Bubble point) and the average pore size. The results show good correlation with measured values. However, the measured and estimated values tend to diverge in high weft density fabrics. This phenomenon is thought to be a result of a more tortuous flow path of denser fabrics, and could most probably be cured by using another value for the tortuosity factor.

Automated User Interface testing in Symbian Operating System

Tässä diplomityössä tutkitaan automatisoitua testausta ja käyttöliittymätestauksen tekemistä helpommaksi Symbian-käyttöjärjestelmässä. Työssä esitellään Symbian ja Symbian-sovelluskehityksessä kohdattavia haasteita. Lisäksi kerrotaan testausstrategioista ja -tavoista sekä automatisoidusta testaamisesta. Lopuksi esitetään työkalu, jolla testitapausten luominen toiminnalisuus- ja järjestelmätestaukseen tehdään helpommaksi. Graafiset käyttöliittymättuovat ainutlaatuisia haasteita ohjelmiston testaamiseen. Ne tehdään usein monimutkaisista komponenteista ja niitä suunnitellaan jatkuvasti uusiksi ohjelmistokehityksen aikana. Graafisten käyttöliittymien testaukseen käytetään usein kaappaus- ja toistotyökaluja. Käyttöliittymätestauksen testitapausten suunnittelu ja toteutus vaatii paljon panostusta. Koska graafiset käyttöliittymät muodostavat suuren osan koodista, voitaisiin säästää paljon resursseja tekemällä testitapausten luomisesta helpompaa. Käytännön osuudessa toteutettu projekti pyrkii tähän tekemällä testiskriptien luomisesta visuaalista. Näin ollen itse testien skriptikieltä ei tarvitse ymmärtää ja testien hahmottaminen on myös helpompaa.

Implementation of population balances in simulation of gas-liquid reactors using a CFD-PBM coupled approach

In bubbly flow simulations, bubble size distribution is an important factor in determination of hydrodynamics. Beside hydrodynamics, it is crucial in the prediction of interfacial area available for mass transfer and in the prediction of reaction rate in gas-liquid reactors such as bubble columns. Solution of population balance equations is a method which can help to model the size distribution by considering continuous bubble coalescence and breakage. Therefore, in Computational Fluid Dynamic simulations it is necessary to couple CFD and Population Balance Model (CFD-PBM) to get reliable distribution. In the current work a CFD-PBM coupled model is implemented as FORTRAN subroutines in ANSYS CFX 10 and it has been tested for bubbly flow. This model uses the idea of Multi Phase Multi Size Group approach which was previously presented by Sha et al. (2006) [18]. The current CFD-PBM coupled method considers inhomogeneous flow field for different bubble size groups in the Eulerian multi-dispersed phase systems. Considering different velocity field for bubbles can give the advantageof more accurate solution of hydrodynamics. It is also an improved method for prediction of bubble size distribution in multiphase flow compared to available commercial packages.

Automating The User Interface Implementation Process by Code Generation

3G-radioverkon asetusten hallinnointi suoritetaan säätämällä radioverkkotietokantaan talletettavia parametreja. Hallinnointiohjelmistossa tuhannetradioverkon parametrit näkyvät käyttöliittymäkomponentteina, joita ohjelmiston kehityskaaressa jatkuvasti lisätään, muutetaan ja poistetaan asiakkaan tarpeidenmukaan. Parametrien lisäämisen toteutusprosessi on ohjelmistokehittäjälle työlästä ja mekaanista. Diplomityön tavoitteeksi asetettiin kehittää koodigeneraattori, joka luo kaiken toteutusprosessissa tuotetun koodin automaattisesti niistä määrittelyistä, jotka ovat nykyäänkin saatavilla. Työssä kehitetty generaattori nopeuttaa ohjelmoijan työtä eliminoimalla yhden aikaa vievän ja mekaanisen työvaiheen. Seurauksena saadaan yhtenäisempää ohjelmistokoodia ja säästetään yrityksen ohjelmistotuotannon kuluissa, kun ohjelmoijan taito voidaan keskittää vaativimpiin tehtäviin.

Vaihtokenttämagnetometrin suunnittelu ja rakentaminen

Tämän työn tavoitteena oli suunnitella ja rakentaa vaihtokenttämagnetometri, jolla voidaan tutkia näytteen magneettisia ominaisuuksia eri lämpötiloissa ja eri taajuuksilla. Menetelmänä käytettiin keskinäisinduktiotekniikkaa, joka on hyvin yleinen tapa tutkia aineen magneettista suskeptibiliteettiä. Magnetometriä ohjataan LabVIEW:lla tehdyllä käyttöliittymällä, joka suunniteltiin yksinkertaiseksi ja helpoksi käyttää. Ohjelma sisältää ohjeet, jotka auttavat parametrien ja toimintojen valinnoissa. LabVIEW:lla ohjataan askelmoottoria, näytteen lämmitintä, lämpötilan mittausta ja lukitusvahvistinta, jolta mittaustulokset saadaan. Laitteen testauksessa käytettiin korkean lämpötilan suprajohdetta YBa2Cu3O6+x, koska sillä saadaan aikaan suurisignaali. Mittaukset tehtiin nestemäisen typen lämpötilassa kahdella eri taajuuden arvolla. Laite antoi oikeanlaisen signaalin ulos eli todettiin laitteen toimivan. Laite toimii hyvin korkeammilla taajuuksilla. Mentäessä hyvin matalille taajuuksille, lukitusvahvistin ei pystynyt lukittumaan, eikä siis siten antanut oikeanlaisia tuloksia.

Modelling the Knowledge Interface between Sales and Production Functions of a Company. Case: New Service Development Process.

Yrityksen sisäisten rajapintojen tunteminen mahdollistaa tiedonvaihdon hallinnan läpi organisaation. Idean muokkaaminen kannattavaksi innovaatioksi edellyttää organisaation eri osien läpi kulkevaa saumatonta prosessiketjua sekä tietovirtaa. Tutkielman tavoitteena oli mallintaa organisaation kahden toiminnallisesti erilaisen osan välinen tiedon vaihto. Tiedon vaihto kuvattiin rajapintana, tietoliittymänä. Kolmiulotteinen organisaatiomalli muodosti tutkimuksen pääteorian. Se kytkettiin yrityksen tuotanto- ja myyntiosiin, kuten myös BestServ-projektin kehittämään uuteen palvelujen kehittämisen prosessiin. Uutta palvelujen kehittämisen prosessia laajennettiin ISO/IEC 15288 standardin kuvaamalla prosessimallilla. Yritysarkkitehtuurikehikoita käytettiin mallintamisen perustana. Tietoliittymä nimenä kuvastaa näkemystä siitä, että tieto [tietämys] on olemukseltaan yksilöiden tai ryhmien välistä. Mallinnusmenetelmät eivät kuitenkaan vielä mahdollista tietoon [tietämykseen] liittyvien kaikkien ominaisuuksien mallintamista. Tietoliittymän malli koostuu kolmesta osasta, joista kaksi esitetään graafisessa muodossa ja yksi taulukkona. Mallia voidaan käyttää itsenäisesti tai osana yritysarkkitehtuuria. Teollisessa palveluliiketoiminnassa sekä tietoliittymän mallinnusmenetelmä että sillä luotu malli voivat auttaa konepajateollisuuden yritystä ymmärtämään yrityksen kehittämistarpeet ja -kohteet, kun se haluaa palvelujen tuottamisella suuremman roolin asiakasyrityksen liiketoiminnassa. Tietoliittymän mallia voidaan käyttää apuna organisaation tietovarannon ja tietämyksen mallintamisessa sekä hallinnassa ja näin pyrkiä yhdistämään ne yrityksen strategiaa palvelevaksi kokonaisuudeksi. Tietoliittymän mallinnus tarjoaa tietojohtamisen kauppatieteelliselle tutkimukselle menetelmällisyyden tutkia innovaatioiden hallintaa sekä organisaation uudistumiskykyä. Kumpikin tutkimusalue tarvitsevat tarkempaa tietoa ja mahdollisuuksia hallita tietovirtoja, tiedon vaihtoa sekä organisaation tietovarannon käyttöä.

Solid and liquid biofuels markets in Finland - a study on international biofuels trade

This study considered the current situation of solid and liquid biofuels markets and international biofuels trade in Finland and identified the challenges ofthe emerging international biofuels markets for Finland. The fact that industryconsumes more than half of the total primary energy, widely applied combined heat and power production (CHP) and a high share of biofuels in the total energy consumption are specific to the Finnish energy system. One third of the electricity is generated in CHP plants. As much as 27% of the total energy consumption ismet by using wood and peat, which makes Finland the leading country in the use of biofuels. Finland has made a commitment to maintain greenhouse gas emissions at the 1990 level at the highest during the period 2008-2012. The Finnish energypolicy aims to achieve the target, and a variety of measures are taken to promote the use of renewable energy sources and especially wood fuels. In this study, the wooden raw material streams of the forest industry were included the international biofuels trade in addition to biomass streams that are traded for energy production. In 2004, as much as 45% of the raw wood importedinto Finland ended up in energy production. The total international trading of biofuels was evaluated at 72 PJ, of which the majority, 58 PJ, was raw wood. About 22% of wood based energy in Finland originated from imported raw wood. Tall oil and wood pellets composed the largest export streams of biofuels. The annual turnover of international biofuels trade was estimated at about ¤ 90 million fordirect trade and at about ¤ 190 million for indirect trade. The forest industryas the biggest user of wood, and the producer and user of wood fuels has a central position in biomass and biofuels markets in Finland. Lately, the international aspects of Finnish biofuels markets have been emphasised as the import of rawwood and the export of wood pellets have increased. Expanding the use of biofuels in the road transportation sector would increase the international streams ofbiofuels in Finland. In coming years, the international trading of biomass for energy purposes can be expected to continue growing.

Comprehensive Study of Crystal Growth from Solution

Crystal growth is an essential phase in crystallization kinetics. The rate of crystal growth provides significant information for the design and control of crystallization processes; nevertheless, obtaining accurate growth rate data is still challenging due to a number of factors that prevail in crystal growth. In industrial crystallization, crystals are generally grown from multi-componentand multi-particle solutions under complicated hydrodynamic conditions; thus, it is crucial to increase the general understanding of the growth kinetics in these systems. The aim of this work is to develop a model of the crystal growth rate from solution. An extensive literature review of crystal growth focuses on themodelling of growth kinetics and thermodynamics, and new measuring techniques that have been introduced in the field of crystallization. The growth of a singlecrystal is investigated in binary and ternary systems. The binary system consists of potassium dihydrogen phosphate (KDP, crystallizing solute) and water (solvent), and the ternary system includes KDP, water and an organic admixture. The studied admixtures, urea, ethanol and 1-propanol, are employed at relatively highconcentrations (of up to 5.0 molal). The influence of the admixtures on the solution thermodynamics is studied using the Pitzer activity coefficient model. Theprediction method of the ternary solubility in the studied systems is introduced and verified. The growth rate of the KDP (101) face in the studied systems aremeasured in the growth cell as a function of supersaturation, the admixture concentration, the solution velocity over a crystal and temperature. In addition, the surface morphology of the KDP (101) face is studied using ex situ atomic force microscopy (AFM). The crystal growth rate in the ternary systems is modelled on the basis of the two-step growth model that contains the Maxwell-Stefan (MS) equations and a surface-reaction model. This model is used together with measuredcrystal growth rate data to develop a new method for the evaluation of the model parameters. The validation of the model is justified with experiments. The crystal growth rate in an imperfectly mixed suspension crystallizer is investigatedusing computational fluid dynamics (CFD). A solid-liquid suspension flow that includes multi-sized particles is described by the multi-fluid model as well as by a standard k-epsilon turbulence model and an interface momentum transfer model. The local crystal growth rate is determined from calculated flow information in a diffusion-controlled crystal growth regime. The calculated results are evaluated experimentally.

Optimizing the Testing Process in Module Testing – Functional Testing Interface

Today's business environment has become increasingly unexpected and fast changing because of the global competition. This new environment requires the companies to organize their control differently, e.g. by logistic process thinking. Logistic process thinking in software engineering applies the principles of production process to immaterial products. Processes must be optimized, so that every phase adds value to the customer, and the lead times can be cut shorter to meet the new customer requirements. The purpose of this thesis is to examine and optimize the testing processes of software engineering concentrating on module testing, functional testing and their interface. The concept of logistic process thinking is introduced through production process, value added model and process management. Also theory of testing based on literature is presented, concentrating on module testing and functional testing. The testing processes of the Case Company are presented together with the project models in which they are implemented. The real life practices in module testing and functional testing and their interface are examined through interviews. These practices are analyzed against the processes and the testing theory, through which ideas for optimizing the testing process are introduced. The project world of the Case Company is also introduced together with two example testing projects in different life cycle phases. The examples give a view of how much effort of the project is put in different types of testing.

Liquid Packaging Board Market in China

Tämän diplomityön tavoitteena on määrittää liiketoimintailmapiiri ja markkinapotentiaali Kiinan nestepakkauskartonkimarkkinoilla. Tutkimus tukee nestepakkauskartonkivalmistajan vientitoimintoja. Pääosin käytännön tiedoista koostuva tutkimus suoritettiin keräämällä sekundaääritietoa ja haastattelemalla alan erikoisasiantuntijoita. Suuri ja kasvava väestö sekä nopeasti kehittyvä talous tukee nestepakkauskartonkimarkkinoiden kasvua Kiinassa. Viimeaikainen globalisaatio haittapuolineen saattaa kuitenkin horjuttaa poliittista ja sosiaalista tasapainoa ja tätä kautta ylellisyys hyödykkeiden kuten kartonkipakattujen tuotteiden kysyntää Kiinassa. Tuontirajoitukset Kiinaan ovat laskemassa valtion tämän hetkisen kansainvälistymispolitiikan seurauksena. Kartonki vahvistaa asemaansa kilpailevien pakkausmateriaalien joukossa. Kiinan kokonaisnestepakkauskartonkimarkkinat kasvavat vuosittain 10,7 % ja ovat vuonna 2001 noin 100 000 tonnia.

Portable Application User Interface Development in Symbian OS

Symbian OS on käyttöjärjestelmä edistyneille matkapuhelimille. Symbiania käyttävistä laitteista on monia muunnoksia. Joitakin käytetään näppäimistön avulla ja toisia kynällä. Näytön mittasuhteet ja muut ominaisuudet vaihtelevat huomattavasti älypuhelimista kommunikaattoreihin. Tämän seurauksena Symbianin eri laiteperheiden viitemallien käyttöliittymäosat ovat sovelluskehittäjän kannalta melko erilaisia. Esimerkiksi kaikki käyttöliittymäkomponentit eivät ole saatavilla kaikissa laiteperheissä. Perinteisesti sovellusten käyttöliittymät on kirjoitettu erikseen kullekin laiteperheelle, mikä pidentää kehitysaikaa. Tämä työ esittelee Symbianin käyttöliittymäarkkitehtuurin, siirrettävyyden käsitteen ja tekniikoita sovellusten suunnitteluun ja toteutukseen, joilla saavutetaan parempi siirrettävyys Symbian-ympäristössä. Työssä suunnitellaan ja toteutetaan AppTest-nimisen testaustyökalun käyttöliittymä siten, että sovellus on helposti siirrettävissä eri laiteperheisiin.

Web user interface architecture for advanced planning and scheduling systems Case: Nokia Demand / Supply Planning Applications

In modem hitec industry Advanced Planning and Scheduling (APS) systems provide the basis for e-business solutions towards the suppliers and the customers. One objective of this thesis was to clarify the modem supply chain management with the APS systems and especially concentrate on the area of Collaborative Planning. In order Advanced Planning and Scheduling systems to be complete and usable, user interfaces are needed. Current Visual Basic user interfaces have faced many complaints and arguments from the users as well as from the development team. This thesis is trying to analyze the reasons and causes for the encountered problems and also provide ways to overcome them. The decision has been made to build the new user interfaces to be Web-enabled. Therefore another objective of this thesis was to research and find suitable technologies for building the Web-based user interfaces for Advanced Planning and Scheduling Systems in Nokia Demand/Supply Planning business area. Comparison between the most suitable technologies is made. Usability issues of Web-enabled user interfaces are also covered. The empirical part of the thesis includes design and implementation of a Web-based user interface with the chosen technology for a particular APS module that enables Collaborative Planning with suppliers.