Ionic liquid mediated biomass deconstruction: from analysis challenges to fermentable sugars

Ionic liquids, ILs, have recently been studied with accelerating interest to be used for a deconstruction/fractionation, dissolution or pretreatment processing method of lignocellulosic biomass. ILs are usually utilized combined with heat. Regarding lignocellulosic recalcitrance toward fractionation and IL utilization, most of the studies concern IL utilization in the biomass fermentation process prior to the enzymatic hydrolysis step. It has been demonstrated that IL-pretreatment gives more efficient hydrolysis of the biomass polysaccharides than enzymatic hydrolysis alone. Both cellulose (especially cellulose) and lignin are very resistant towards fractionation and even dissolution methods. As an example, it can be mentioned that softwood, hardwood and grass-type plant species have different types of lignin structures leading to the fact that softwood lignin (guaiacyl lignin dominates) is the most difficult to solubilize or chemically disrupt. In addition to the known conventional biomass processing methods, several ILs have also been found to efficiently dissolve either cellulose and/or wood samples – different ILs are suitable for different purposes. An IL treatment of wood usually results in non-fibrous pulp, where lignin is not efficiently separated and wood components are selectively precipitated, as cellulose is not soluble or degradable in ionic liquids under mild conditions. Nevertheless, new ILs capable of rather good fractionation performance have recently emerged. The capability of the IL to dissolve or deconstruct wood or cellulose depends on several factors, (e.g. sample origin, the particle size of the biomass, mechanical treatments as pulverization, initial biomassto-IL ratio, water content of the biomass, possible impurities of IL, reaction conditions, temperature etc). The aim of this study was to obtain (fermentable) saccharides and other valuable chemicals from wood by a combined heat and IL-treatment. Thermal treatments alone contribute to the degradation of polysaccharides (e.g. 150 °C alone is said to cause the degradation of polysaccharides), thus temperatures below that should be used, if the research interest lies on the IL effectiveness. On the other hand, the efficiency of the IL-treatment can also be enhanced to combine other treatment methods, (e.g. microwave heating). The samples of spruce, pine and birch sawdust were treated with either 1-Ethyl-3-methylimidazolium chloride, Emim Cl, or 1-Ethyl-3-methylimidazolium acetate, Emim Ac, (or with ionized water for comparison) at various temperatures (where focus was between 80 and 120 °C). The samples were withdrawn at fixed time intervals (the main interest treatment time area lied between 0 and 100 hours). Double experiments were executed. The selected mono- and disaccharides, as well as their known degradation products, 5-hydroxymethylfurfural, 5-HMF, and furfural were analyzed with capillary electrophoresis, CE, and high-performance liquid chromatography, HPLC. Initially, even GC and GC-MS were utilized. Galactose, glucose, mannose and xylose were the main monosaccharides that were present in the wood samples exposed to ILs at elevated temperatures; in addition, furfural and 5-HMF were detected; moreover, the quantitative amount of the two latter ones were naturally increasing in line with the heating time or the IL:wood ratio.

Simulation and optimization of IGCC technique for power generation and hydrogen production by using lignite Thar coal and cotton stalk

The purpose of this study was to simulate and to optimize integrated gasification for combine cycle (IGCC) for power generation and hydrogen (H2) production by using low grade Thar lignite coal and cotton stalk. Lignite coal is abundant of moisture and ash content, the idea of addition of cotton stalk is to increase the mass of combustible material per mass of feed use for the process, to reduce the consumption of coal and to increase the cotton stalk efficiently for IGCC process. Aspen plus software is used to simulate the process with different mass ratios of coal to cotton stalk and for optimization: process efficiencies, net power generation and H2 production etc. are considered while environmental hazard emissions are optimized to acceptance level. With the addition of cotton stalk in feed, process efficiencies started to decline along with the net power production. But for H2 production, it gave positive result at start but after 40% cotton stalk addition, H2 production also started to decline. It also affects negatively on environmental hazard emissions and mass of emissions/ net power production increases linearly with the addition of cotton stalk in feed mixture. In summation with the addition of cotton stalk, overall affects seemed to negative. But the effect is more negative after 40% cotton stalk addition so it is concluded that to get maximum process efficiencies and high production less amount of cotton stalk addition in feed is preferable and the maximum level of addition is estimated to 40%. Gasification temperature should keep lower around 1140 °C and prefer technique for studied feed in IGCC is fluidized bed (ash in dry form) rather than ash slagging gasifier

Aqueous-phase reforming of renewables for selective hydrogen production in the presence of supported platinum catalysts

The evolution of our society is impossible without a constant progress in life-important areas such as chemical engineering and technology. Innovation, creativity and technology are three main components driving the progress of chemistry further towards a sustainable society. Biomass, being an attractive renewable feedstock for production of fine chemicals, energy-rich materials and even transportation fuels, captures progressively new positions in the area of chemical technology. Knowledge of heterogeneous catalysis and chemical technology applied to transformation of biomass-derived substances will open doors for a sustainable economy and facilitates the discovery of novel environmentally-benign processes which probably will replace existing technologies in the era of biorefinary. Aqueous-phase reforming (APR) is regarded as a promising technology for production of hydrogen and liquids fuels from biomass-derived substances such as C3-C6 polyols. In the present work, aqueous-phase reforming of glycerol, xylitol and sorbitol was investigated in the presence of supported Pt catalysts. The catalysts were deposited on different support materials, including Al2O3, TiO2 and carbons. Catalytic measurements were performed in a laboratory-scale continuous fixedbed reactor. An advanced analytical approach was developed in order to identify reaction products and reaction intermediates in the APR of polyols. The influence of the substrate structure on the product formation and selectivity in the APR reaction was also investigated, showing that the yields of the desired products varied depending on the substrate chain length. Additionally, the influence of bioethanol additive in the APR of glycerol and sorbitol was studied. A reaction network was advanced explaining the formation of products and key intermediates. The structure sensitivity in the aqueous-phase reforming reaction was demonstrated using a series of platinum catalysts supported on carbon with different Pt cluster sizes in the continuous fixed-bed reactor. Furthermore, a correlation between texture physico-chemical properties of the catalysts and catalytic data was established. The effect of the second metal (Re, Cu) addition to Pt catalysts was investigated in the APR of xylitol showing a superior hydrocarbon formation on PtRe bimetallic catalysts compared to monometallic Pt. On the basis of the experimental data obtained, mathematical modeling of the reaction kinetics was performed. The developed model was proven to successfully describe experimental data on APR of sorbitol with good accuracy.

Catalytic upgrading of biomass extractives to fine chemicals over supported ionic liquid catalysts (SILCAs)

Behovet av förnyelsebar energi ökar ständigt eftersom det finns en strävan att minska beroendet av fossila bränslen. Dessutom är tillgångar av fossila bränslen begränsade. Miljövänliga processer för bioraffinaderier erbjuder en stor möjlighet för produktion av energi, bränslen och kemikalier. Den finska och svenska skogsindustrin har en lång tradition i utnyttjandet av skogsbiomassor. Bioraffinaderier som integreras med pappers- och cellulosaindustrin kan frambringa både ekonomiska och ekologiska fördelar i framställning av traditionella och biobaserade produkter. I doktorsarbetet studerades omvandling av extraktivämnen till finkemikalier som kan användas t.ex. av läkemedelsindustrin. Extraktivämnen fås ur biomassa. I forskningsarbetet framställdes biobaserade finkemikalier med hjälp av katalysatorer som baserar sig på joniska vätskor. Biomassan består av cellulosa, hemicellulosa, lignin och extraktivämnen, vilka huvudsakligen är terpener, vaxer och fettsyror. Extraktivämen är vedens komponenter, som kan separeras ur vedmaterialet med hjälp av neutrala lösningsmedel. Joniska vätskekatalysatorer som var immobiliserade på fasta bärare utnyttjades för isomerisering av α,β-pinenoxider samt hydrogenering citral. Inverkan av joniska vätskor på katalysatorns aktivitet och reaktionernas produktfördelning undersöktes under varierande reaktionsbetingelser. Kinetiska modeller för pinenoxidens isomeriseringsreaktioner beskrev väl experimentellt upptäckta skillnader mellan olika katalysatorer. --------------------------------------------------- Uusiutuvan energian tarve on kasvussa, koska riippuvuutta fossiilisista polttoaineista pyritään vähentämään. Tämän lisäksi fossiilisten polttoaineiden varannot ovat rajalliset. Ympäristöystävälliset biojalostusprosessit ovat näin ollen suuri mahdollisuus energian, polttoaineiden ja kemikaalien tuotannossa. Suomen ja Ruotsin metsäteollisuudella on pitkät perinteet metsäbiomassojen hyödyntämisessä. Paperi- ja selluteollisuuden yhteyteen integroiduilla biojalostamoilla voidaan luoda taloudellisia ja ympäristöllisiä etuja sekä perinteisten että biopohjaisten tuotteiden valmistuksessa. Väitöstyössä on tutkittu biomassan uuteaineiden kemiallista muuntamista hienokemikaaleiksi, joita voidaan käyttää esimerkiksi lääkeaineteollisuudessa. Biopohjaisia hienokemikaaleja on valmistettu biomassan uuteaineista ionisiin nesteisiin perustuvilla katalyyteillä. Biomassa koostuu selluloosasta, hemiselluloosasta, ligniinistä sekä uuteaineista, jotka ovat pääosin terpeenejä, vahoja tai rasvahappoja. Uuteaineet ovat puun komponentteja, jotka voidaan erottaa puusta neutraalien liuottimien avulla. Kiinteän kantajan päälle immobilisoituja ionisia nestekatalyyttejä (Supported Ionic Liquid Catalyst) hyödynnettiin α,β-pineenioksidien isomerisointireaktioissa sekä sitraalin vedytysreaktioissa. Ionisten nesteiden vaikutusta katalyyttien aktiivisuuteen sekä reaktioiden tuotejakaumaan tutkittiin erilaisissa reaktio-olosuhteissa. Pineenioksidien isomerisointireaktioiden kineettiset mallit kuvasivat hyvin kokeellisesti todettuja katalyyttien eroavaisuuksia.

Review of water electrolysis technologies and design of renewable hydrogen production systems

An electric system based on renewable energy faces challenges concerning the storage and utilization of energy due to the intermittent and seasonal nature of renewable energy sources. Wind and solar photovoltaic power productions are variable and difficult to predict, and thus electricity storage will be needed in the case of basic power production. Hydrogen’s energetic potential lies in its ability and versatility to store chemical energy, to serve as an energy carrier and as feedstock for various industries. Hydrogen is also used e.g. in the production of biofuels. The amount of energy produced during hydrogen combustion is higher than any other fuel’s on a mass basis with a higher-heating-value of 39.4 kWh/kg. However, even though hydrogen is the most abundant element in the universe, on Earth most hydrogen exists in molecular forms such as water. Therefore, hydrogen must be produced and there are various methods to do so. Today, the majority hydrogen comes from fossil fuels, mainly from steam methane reforming, and only about 4 % of global hydrogen comes from water electrolysis. Combination of electrolytic production of hydrogen from water and supply of renewable energy is attracting more interest due to the sustainability and the increased flexibility of the resulting energy system. The preferred option for intermittent hydrogen storage is pressurization in tanks since at ambient conditions the volumetric energy density of hydrogen is low, and pressurized tanks are efficient and affordable when the cycling rate is high. Pressurized hydrogen enables energy storage in larger capacities compared to battery technologies and additionally the energy can be stored for longer periods of time, on a time scale of months. In this thesis, the thermodynamics and electrochemistry associated with water electrolysis are described. The main water electrolysis technologies are presented with state-of-the-art specifications. Finally, a Power-to-Hydrogen infrastructure design for Lappeenranta University of Technology is presented. Laboratory setup for water electrolysis is specified and factors affecting its commissioning in Finland are presented.

Liquid-phase alcohol promoted methanol synthesis from CO2 and H2

Methanol is an important and versatile compound with various uses as a fuel and a feedstock chemical. Methanol is also a potential chemical energy carrier. Due to the fluctuating nature of renewable energy sources such as wind or solar, storage of energy is required to balance the varying supply and demand. Excess electrical energy generated at peak periods can be stored by using the energy in the production of chemical compounds. The conventional industrial production of methanol is based on the gas-phase synthesis from synthesis gas generated from fossil sources, primarily natural gas. Methanol can also be produced by hydrogenation of CO2. The production of methanol from CO2 captured from emission sources or even directly from the atmosphere would allow sustainable production based on a nearly limitless carbon source, while helping to reduce the increasing CO2 concentration in the atmosphere. Hydrogen for synthesis can be produced by electrolysis of water utilizing renewable electricity. A new liquid-phase methanol synthesis process has been proposed. In this process, a conventional methanol synthesis catalyst is mixed in suspension with a liquid alcohol solvent. The alcohol acts as a catalytic solvent by enabling a new reaction route, potentially allowing the synthesis of methanol at lower temperatures and pressures compared to conventional processes. For this thesis, the alcohol promoted liquid phase methanol synthesis process was tested at laboratory scale. Batch and semibatch reaction experiments were performed in an autoclave reactor, using a conventional Cu/ZnO catalyst and ethanol and 2-butanol as the alcoholic solvents. Experiments were performed at the pressure range of 30-60 bar and at temperatures of 160-200 °C. The productivity of methanol was found to increase with increasing pressure and temperature. In the studied process conditions a maximum volumetric productivity of 1.9 g of methanol per liter of solvent per hour was obtained, while the maximum catalyst specific productivity was found to be 40.2 g of methanol per kg of catalyst per hour. The productivity values are low compared to both industrial synthesis and to gas-phase synthesis from CO2. However, the reaction temperatures and pressures employed were lower compared to gas-phase processes. While the productivity is not high enough for large-scale industrial operation, the milder reaction conditions and simple operation could prove useful for small-scale operations. Finally, a preliminary design for an alcohol promoted, liquid-phase methanol synthesis process was created using the data obtained from the experiments. The demonstration scale process was scaled to an electrolyzer unit producing 1 Nm3 of hydrogen per hour. This Master’s thesis is closely connected to LUT REFLEX-platform.

Optimization of hydrogen plant efficiency

The purpose of this master’s thesis was to study ways to increase the operating cost-efficiency of the hydrogen production process by optimizing the process parameters while, at the same time, maintaining plant reliability and safety. The literature part reviewed other hydrogen production and purification processes as well as raw material alternatives for hydrogen production. The experimental part of the master’s thesis was conducted at Solvay Chemicals Finland Oy’s hydrogen plant in spring 2012. It was performed by changing the process parameters, first, one by one, aiming for a more efficient process with clean product gas and lower natural gas consumption. The values of the process parameters were tested based on the information from the literature, process simulation and experiences of previous similar processes. The studied parameters were reformer outlet temperature, shift converter inlet temperature and steam/carbon ratio. The results show that the optimal process conditions are a lower steam/carbon ratio and reformer outlet temperature than the current values of 3.0 and 798 °C. An increase/decrease in the shift conversion inlet temperature does not affect natural gas consumption, but it has an effect on minimizing the process steam overload.

Towards novel biogas upgrading processes

Biogas production has considerable development possibilities not only in Finland but all over the world since it is the easiest way of creating value out of various waste fractions and represents an alternative source of renewable energy. Development of efficient biogas upgrading technology has become an important issue since it improves the quality of biogas and for example facilitating its injection into the natural gas pipelines. Moreover, such upgrading contributes to resolving the issue of increasing CO2 emissions and addresses the increasing climate change concerns. Together with traditional CO2 capturing technologies a new class of recently emerged sorbents such as ionic liquids is claimed as promising media for gas separations. In this thesis, an extensive comparison of the performance of different solvents in terms of CO2 capture has been performed. The focus of the present study was on aqueous amine solutions and their mixtures, traditional ionic liquids, ‘switchable’ ionic liquids and poly(ionic liquid)s in order to reveal the best option for biogas upgrading. The CO2 capturing efficiency for the most promising solvents achieved values around 50 - 60 L CO2 / L absorbent. These values are superior to currently widely applied water wash biogas upgrading system. Regeneration of the solvent mixtures appeared to be challenging since the loss of initial efficiency upon CO2 release was in excess of 20 - 40 vol %, especially in the case of aqueous amine solutions. In contrast, some of the ionic liquids displayed reversible behavior. Thus, for selected “switchable” ionic and poly(ionic liquid)s the CO2 absorption/regeneration cycles were performed 3 - 4 times without any notable efficiency decrease. The viscosity issue, typical for ionic liquids upon CO2 saturation, was addressed and the information obtained was evaluated and related to the ionic interactions. The occurrence of volatile organic compounds (VOCs) before and after biogas upgrading was studied for biogas produced through anaerobic digestion of waste waters sludge. The ionic liquid [C4mim][OAc] demonstrated its feasibility as a promising scrubbing media and exhibited high efficiency in terms of the removal of VOCs. Upon application of this ionic liquid, the amount of identified VOCs was diminished by around 65 wt %, while the samples treated with the aqueous mixture of 15 wt % N-methyldiethanolamine with addition of 5 wt % piperazine resulted in 32 wt % reduction in the amounts of volatile organic compounds only.

Topochemistry of physical and chemical pretreatments of biomass as investigated by FE-SEM, XPS and ToF-SIMS

Surface chemistry is of great importance in plant biomass engineering and applications. The surface chemical composition of biomass which includes lignin, carbohydrates and extractives influences its interactions with chemical agents, such as pulp processing/papermaking chemicals, or enzymes for different purposes. In this thesis, the changes in the surface chemical composition of lignocellulosic biomass after physical modification for the improvement of resulting paper properties and chemical treatment for the enhancement of enzymatic hydrolysis were investigated. Low consistency (LC) refining was used as physical treatment of bleached softwood and hardwood pulp samples, and the surface chemistry of refined samples was investigated. The refined pulp was analysed as whole pulp while the fines-free fibre samples were characterized separately. The fines produced in LCrefining contributed to an enlarged surface specific area as well as the change of surface coverage by lignin and extractives, as investigated by X-ray photoelectron spectroscopy (XPS). The surface coverage by lignin of the whole pulp decreased after refining while the surface coverage by extractives increased both for pine and eucalyptus. In the case of pine, the removal of fines resulted in reduction of the surface coverage by extractives, while the surface coverage by lignin increased on fibre sample (without fines). In the case of eucalyptus, the surface coverage by lignin of fibre samples decreased after the removal of fines. In addition, the surface distribution of carbohydrates, lignin and extractives of pine and eucalyptus samples was determined by Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). LC-refining increased the amounts of pentose, hexose and extractives on the surface of pine samples. ToF-SIMS also gave clear evidence about xylan deposition and reduction of surface lignin distribution on the fibre of eucalyptus. However, the changes in the surface chemical composition during the physical treatment has led to an increase in the adsorption of fluorescent whitening agents (FWAs) on fibres due to a combination of electro-static forces, specific surface area of fibres and hydrophobic interactions. Various physicochemical pretreatments were conducted on wood and non-wood biomass for enhancing enzymatic hydrolysis of polysaccharides, and the surface chemistry of the pretreated and enzymatically hydrolysed samples was investigated by field emission scanning electron microscopy (FE-SEM), XPS and ToF-SIMS. A hydrotrope was used as a relatively novel pretreatment technology both in the case of wood and non-wood biomass. For comparison, ionic liquid and hydrothermal pretreatments were applied on softwood and hardwood as well. Thus, XPS analysis showed that the surface lignin was more efficiently removed by hydrotropic pretreatment compared to ionic liquid or hydrothermal pretreatments. SEM analysis also found that already at room temperature the ionic liquid pretreatments were more effective in swelling the fibres compared with hydrotropic pretreatment at elevated temperatures. The enzymatic hydrolysis yield of hardwood was enhanced due to the decrease in surface coverage of lignin, which was induced by hydrotropic treatment. However, hydrotropic pretreatment was not appropriate for softwood because of the predominance of guaiacyl lignin structure in this material. In addition, the reduction of surface lignin and xylan during pretreatment and subsequent increase in cellulose hydrolysis by enzyme could be observed from ToF-SIMS results. The characterisation of the non-wood biomass (e.g. sugarcane bagasse and common reed) treated by hydrotropic method, alkaline and alkaline hydrogen peroxide pretreatments were carried out by XPS and ToF-SIMS. According to the results, the action for the removal of the surface lignin of non-wood biomass by hydrotropic pretreatment was more significant compared to alkaline and alkaline hydrogen peroxide pretreatments, although a higher total amount of lignin could be removed by alkaline and alkaline hydrogen peroxide pretreatment. Furthermore, xylan could be remarkably more efficiently removed by hydrotropic method. Therefore, the glucan yield achieved from hydrotropic treated sample was higher than that from samples treated with alkaline or alkaline hydrogen peroxide. Through the use of ToF-SIMS, the distribution and localization of lignin and carbohydrates on the surface of ignocelluloses during pretreatment and enzymatic hydrolysis could be detected, and xylan degradation during enzymatic hydrolysis could also be assessed. Thus, based on the results from XPS and ToF-SIMS, the mechanism of the hydrotropic pretreatment in improving the accessibility of enzymes to fibre and further ameliorating of the enzymatic saccharification could be better elucidated.

Carbon sources for Power-to-Gas applications in the Finnish energy system

This thesis is done as a part of the NEOCARBON project. The aim of NEOCARBON project is to study a fully renewable energy system utilizing Power-to-Gas or Power-to-Liquid technology for energy storage. Power-to-Gas consists of two main operations: Hydrogen production via electrolysis and methane production via methanation. Methanation requires carbon dioxide and hydrogen as a raw material. This thesis studies the potential carbon dioxide sources within Finland. The different sources are ranked using the cost and energy penalty of the carbon capture, carbon biogenity and compatibility with Power-to-Gas. It can be concluded that in Finland there exists enough CO2 point sources to provide national PtG system with sufficient amounts of carbon. Pulp and paper industry is single largest producer of biogenic CO2 in Finland. It is possible to obtain single unit capable of grid balancing operations and energy transformations via Power-to-Gas and Gas-to-Power by coupling biogas plants with biomethanation and CHP units.

CLEVER-1 as an immune suppressive molecule

The immune response and immune suppression are equally essential for the immune system to protect the host against an infection and to protect self-molecules in different pathophysiological conditions. Pregnancy is one of the conditions where the maternal immune system remains resistant against microbes and yet attains tolerance to protect the fetus, whose genetic material differs partially from the mother’s. However, if the balance of immune suppression is not precise in the host it can favor conditions which lead to diseases, such as cancer and autoimmune disorders. This study was initiated to investigate the expression and functions of CLEVER-1/Stabilin-1, a multifunctional protein expressed on subsets of endothelial cells and type II macrophages, as an immune suppressive molecule. Firstly, the expression of CLEVER-1/stabilin-1 and its function in human placental macrophages were examined. Secondly, the expression profile and functional significance of stabilin-1 on healthy human monocytes was investigated. The results clarified the expression of CLEVER-1/stabilin-1 on placental macrophages, and verified that CLEVER-1/stabilin-1 functions as an adhesion and scavenging molecule on these cells. The data from normal monocytes revealed that the monocytes with low stabilin-1 expression carried a pro-inflammatory gene signature, and that stabilin-1 can directly or indirectly regulate pro-inflammatory genes in monocytes. Finally, it was shown that monocyte CLEVER-1/stabilin-1 dampens IFN production by T cells. To conclude, CLEVER-1/stabilin-1 is defined as an immune suppressive molecule on monocytes and macrophages. Strikingly, anti-stabilin-1 antibodies may have the potential to promote the Th1 dependent inflammatory response and counteract the tumor induced immune suppression.

Litiumin talteenotto luonnon suola-altaista ionisilla nesteillä

Uusiutuvan energian käytön lisääntyminen lisää sähkön varastoinnin tarvetta. Litiumioniakku-jen on todettu olevan oivallisia keinoja varastoida sähköä esimerkiksi sähköautojen energian-lähteeksi. Tästä syystä akkujen kysyntä kasvaa nopeaa tahtia, jolloin nykyiset litiumlähteet ei-vät enää riitä tuottamaan tarpeeksi litiumia kasvavaan tarpeeseen. Tämän vuoksi litiumin tal-teenottoon tulee valjastaa uusia litiumin lähteitä, joiden hyödynnettävyys nykyisellä tekniikalla on pienen litiumkonsentraation ja muiden alkali- ja maa-alkalimetallien läsnäolon takia vaikeaa. Tällä hetkellä litiumia otetaan talteen eniten korkean litiumpitoisuuden luonnon suolajärvistä. Nykyisin käytössä oleva litiumin erotusprosessi on hidas ja sen käyttö pienten litiumkonsent-raatioiden suola-altailla on kannattamatonta. Tehokkaampana talteenottomenetelmänä luonnon suolajärvillä nähdään litiumin selektiivinen uutto ionisilla nesteillä. Menetelmä on todettu toi-mivaksi suolajärvillä, joilla on matala litiumkonsentraatio. Uusien suolajärvien käyttöönotto ei ratkaise kaikkia litiumin talteenottoon liittyviä ongelmia, sillä suolajärvet ovat alttiita ilmastonmuutokselle, eikä niiden litiumvarannot ole ehtymättömät. Merien litiumvarantoja sen sijaan pidetään lähes ehtymättöminä. Litiumin talteenotto meristä on mahdollista ionisia nesteitä ja membraaneja hyödyntävällä elektrodialyysilaitteistolla, jolla litiumia voidaan ottaa talteen myös hyvin pienistä pitoisuuksista. Lisäksi on mahdollista, että litiumin talteenottoon yhdistetään juomaveden valmistus. Tällainen vedenpuhdistusprosessi olisi myös hyvä kestävän kehityksen näkökulmasta.

Membraanien kestävyys ionisessa nesteessä

Tämän diplomityön tavoitteena oli etsiä mahdollisimman hyvin ionista nestettä kestävä yleisesti kaupallisesti saatavilla oleva nano- tai ultrasuodatusmembraani. Kirjallisuusosassa on perehdytty yleisesti membraanitekniikan ja ionisten nesteiden historiaan sekä niiden ominaisuuksiin ja käyttösovelluksiin. Membraaniprosesseista on lyhyesti käyty läpi mikro-, ultra- ja nanosuodatus sekä käänteisosmoosi ja pervaporaatio. Kokeellisessa osassa tutkittiin neljäntoista kaupallisesti saatavilla olevien nano- ja ultrasuodatusmembraanien kestävyyttä ionisessa nesteessä. Tutkimuksessa käytettyjen membraanien vesi- ja malliaineliuosvuon arvoja sekä retentioita vertailtiin ennen ja jälkeen ioniselle nesteelle altistusta. Tulokset osoittivat, että polyamidista, polyeetterisulfonista ja sulfonoidusta polyeetterisulfonista valmistettujen membraanien suodatusominaisuudet muuttuivat niiden altistuessa ioniselle nesteelle. Näiden membraanien permeabiliteetit ja retentiot laskivat viikon altistuksen jälkeen merkittävästi. Erityisesti liuottimia kestäviksi suunnitellut membraanit säilyttivät erotusominaisuutensa paremmin.

Öljynjalostamon vetyverkon PINCH-analyysi

Tässä diplomityössä on tarkasteltu Porvoon öljynjalostamon vetyverkkoa ja pohdittu keinoja, joilla vedyn käyttöä jalostamolla voitaisiin tehostaan sekä polttokaasuverkkoon menevän vedyn määrä pienentää. Tarkastelun lähtökohtana toimii vetytaseen pohjalta laadittu vetypinch-analyysi. Kirjallisuusosassa on esitelty jalostamon vetyverkkoon kuuluvat yksiköt sekä käsitelty lyhyesti niiden toimintaa. Lisäksi on käsitelty vetypinch-analyysin periaate, sekä kuinka todelliset prosessirajoitteet voidaan huomioida sitä toteutettaessa. Kirjallisuusosan lopussa on esitetty miten vetyverkon vaiheittainen optimointi etenee. Työn soveltavassa osassa laadittiin vetyverkon virtauskaavio, jolla saatiin luotua kattava käsitys jalostamon vedynjakelusta. Virtauskaaviosta tehtiin yksinkertaistettu versio, jonka perusteella laadittiin vetytase. Vetytaseen pohjalta suoritettiin vetypinch-analyysi, jonka mukaan jalostamolla tuotettiin tasehetkellä ylimäärin vetyä. Vedyn käytön tehostamiseksi jalostamolla tulee rikkivedyn talteenottoyksikkö 2:n polttokaasuvirta pyrkiä minimoimaan tai hyödyntämään. Lisäksi virtausmittareiden mitoituspisteiden molekyylimassat tulisi muuttaa vastaamaan paremmin nykyistä ajotilannetta, sekä seurata niitä jatkossa säännöllisesti. Myös vetypitoisuutta mittaavien online-analysaattoreiden kalibroinnista tulee huolehtia, ja ottaa riittävästi kenttänäytteitä vetyverkosta. On huomattava, että öljynjalostamon vedyn tuotannon minimointi ei ole aina automaattisesti taloudellisin ratkaisu. Joissain tapauksissa vedyn osapaineen nostaminen vetyä kuluttavan yksikön reaktorissa voi lisätä yksikön tuottavuutta niin paljon, että se kompensoi lisääntyneestä vedyn tuotannosta aiheutuvat kustannukset.

Selluloosamembraanien kehittäminen ja testaus

Tämän työn tavoitteena oli selvittää, kuinka selluloosan lisääminen vaikuttaa polysulfonirunkoisiin membraaneihin. Lisäksi työssä selvitettiin selluloosamembraanien modifiointia kitosaanilla ja bentoniitilla. Työssä muodostettiin membraanit faasi-inversiotekniikalla. Selluloosamembraanien valmistuksessa jauhettu selluloosa liuotettiin ioniseen nesteeseen. Sekä polysulfonista että selluloosasta valmistetuille membraaneille määritettiin puhdasvesivuot ja retentiot. Retention määrittämiseen käytettiin malliaineena dekstraanin vesiliuosta. Lisäksi määriteltiin polysulfonipohjaisten membraanien hydrofiilisyys tutkimalla membraanien pintojen ja vesipisaroiden välisiä kontaktikulmia. Polysulfonimembraaneihin lisätyn selluloosan havaittiin pienentävän puhdasvesivuota ja kasvattavan hydrofiilisyyttä mitä enemmän selluloosaa oli membraanimatriisissa. Kaikkien selluloosalla modifioitujen membraanien retentiot olivat suurempia kuin modifioimattoman polysulfonimembraanin. Kitosaanilla modifioitujen selluloosamembraanien valmistus ei onnistunut johtuen luultavasti kitosaanin liian suuresta partikkelikoosta. Bentoniitilla modifioitujen membraanien vuot olivat merkittävästi suuremmat sekä niiden retentiot pienemmät verrattuna modifioimattomaan selluloosamembraaniin. Tämä johtui luultavasti siitä, että bentoniitin lisääminen aiheutti membraanirakenteeseen reikiä.