Dynamic Model of a Small Once-Through Boiler

In this study, a model for the unsteady dynamic behaviour of a once-through counter flow boiler that uses an organic working fluid is presented. The boiler is a compact waste-heat boiler without a furnace and it has a preheater, a vaporiser and a superheater. The relative lengths of the boiler parts vary with the operating conditions since they are all parts of a single tube. The present research is a part of a study on the unsteady dynamics of an organic Rankine cycle power plant and it will be a part of a dynamic process model. The boiler model is presented using a selected example case that uses toluene as the process fluid and flue gas from natural gas combustion as the heat source. The dynamic behaviour of the boiler means transition from the steady initial state towards another steady state that corresponds to the changed process conditions. The solution method chosen was to find such a pressure of the process fluid that the mass of the process fluid in the boiler equals the mass calculated using the mass flows into and out of the boiler during a time step, using the finite difference method. A special method of fast calculation of the thermal properties has been used, because most of the calculation time is spent in calculating the fluid properties. The boiler was divided into elements. The values of the thermodynamic properties and mass flows were calculated in the nodes that connect the elements. Dynamic behaviour was limited to the process fluid and tube wall, and the heat source was regarded as to be steady. The elements that connect the preheater to thevaporiser and the vaporiser to the superheater were treated in a special way that takes into account a flexible change from one part to the other. The model consists of the calculation of the steady state initial distribution of the variables in the nodes, and the calculation of these nodal values in a dynamic state. The initial state of the boiler was received from a steady process model that isnot a part of the boiler model. The known boundary values that may vary during the dynamic calculation were the inlet temperature and mass flow rates of both the heat source and the process fluid. A brief examination of the oscillation around a steady state, the so-called Ledinegg instability, was done. This examination showed that the pressure drop in the boiler is a third degree polynomial of the mass flow rate, and the stability criterion is a second degree polynomial of the enthalpy change in the preheater. The numerical examination showed that oscillations did not exist in the example case. The dynamic boiler model was analysed for linear and step changes of the entering fluid temperatures and flow rates.The problem for verifying the correctness of the achieved results was that there was no possibility o compare them with measurements. This is why the only way was to determine whether the obtained results were intuitively reasonable and the results changed logically when the boundary conditions were changed. The numerical stability was checked in a test run in which there was no change in input values. The differences compared with the initial values were so small that the effects of numerical oscillations were negligible. The heat source side tests showed that the model gives results that are logical in the directions of the changes, and the order of magnitude of the timescale of changes is also as expected. The results of the tests on the process fluid side showed that the model gives reasonable results both on the temperature changes that cause small alterations in the process state and on mass flow rate changes causing very great alterations. The test runs showed that the dynamic model has no problems in calculating cases in which temperature of the entering heat source suddenly goes below that of the tube wall or the process fluid.

Non-Linear Journal Bearing Model for Analysis of Superharmonic Vibrations of Rotor Systems

A rotating machine usually consists of a rotor and bearings that supports it. The nonidealities in these components may excite vibration of the rotating system. The uncontrolled vibrations may lead to excessive wearing of the components of the rotating machine or reduce the process quality. Vibrations may be harmful even when amplitudes are seemingly low, as is usually the case in superharmonic vibration that takes place below the first critical speed of the rotating machine. Superharmonic vibration is excited when the rotational velocity of the machine is a fraction of the natural frequency of the system. In such a situation, a part of the machine’s rotational energy is transformed into vibration energy. The amount of vibration energy should be minimised in the design of rotating machines. The superharmonic vibration phenomena can be studied by analysing the coupled rotor-bearing system employing a multibody simulation approach. This research is focused on the modelling of hydrodynamic journal bearings and rotorbearing systems supported by journal bearings. In particular, the non-idealities affecting the rotor-bearing system and their effect on the superharmonic vibration of the rotating system are analysed. A comparison of computationally efficient journal bearing models is carried out in order to validate one model for further development. The selected bearing model is improved in order to take the waviness of the shaft journal into account. The improved model is implemented and analyzed in a multibody simulation code. A rotor-bearing system that consists of a flexible tube roll, two journal bearings and a supporting structure is analysed employing the multibody simulation technique. The modelled non-idealities are the shell thickness variation in the tube roll and the waviness of the shaft journal in the bearing assembly. Both modelled non-idealities may cause subharmonic resonance in the system. In multibody simulation, the coupled effect of the non-idealities can be captured in the analysis. Additionally one non-ideality is presented that does not excite the vibrations itself but affects the response of the rotorbearing system, namely the waviness of the bearing bushing which is the non-rotating part of the bearing system. The modelled system is verified with measurements performed on a test rig. In the measurements the waviness of bearing bushing was not measured and therefore it’s affect on the response was not verified. In conclusion, the selected modelling approach is an appropriate method when analysing the response of the rotor-bearing system. When comparing the simulated results to the measured ones, the overall agreement between the results is concluded to be good.

Defining a framework model to determine total costs of managed desktops using ITIL best practices

In modern day organizations there are an increasing number of IT devices such as computers, mobile phones and printers. These devices can be located and maintained by using specialized IT management applications. Costs related to a single device accumulate from various sources and are normally categorized as direct costs like hardware costs and indirect costs such as labor costs. These costs can be saved in a configuration management database and presented to users using web based development tools such as ASP.NET. The overall costs of IT devices during their lifecycle can be ten times higher than the actual purchase price of the product and ability to define and reduce these costs can save organizations noticeable amount of money. This Master’s Thesis introduces the research field of IT management and defines a custom framework model based on Information Technology Infrastructure Library (ITIL) best practices which is designed to be implemented as part of an existing IT management application for defining and presenting IT costs.

Mobile Subscription Acquisition and Retention Costs - An Actvity-Based Model

The objective of this master’s thesis was to develop a model for mobile subscription acquisition cost, SAC, and mobile subscription retention cost, SRC, by applying activity-based cost accounting principles. The thesis was conducted as a case study for a telecommunication company operating on the Finnish telecommunication market. In addition to activity-based cost accounting there were other theories studied and applied in order to establish a theory framework for this thesis. The concepts of acquisition and retention were explored in a broader context with the concepts of customer satisfaction, loyalty and profitability and eventually customer relationship management to understand the background and meaning of the theme of this thesis. The utilization of SAC and SRC information is discussed through the theories of decision making and activity-based management. Also, the present state and future needs of SAC and SRC information usage at the case company as well as the functions of the company were examined by interviewing some members of the company personnel. With the help of these theories and methods it was aimed at finding out both the theory-based and practical factors which affect the structure of the model. During the thesis study it was confirmed that the existing SAC and SRC model of the case company should be used as the basis in developing the activity-based model. As a result the indirect costs of the old model were transformed into activities and the direct costs were continued to be allocated directly to acquisition of new subscriptions and retention of old subscriptions. The refined model will enable managing the subscription acquisition, retention and the related costs better through the activity information. During the interviews it was found out that the SAC and SRC information is also used in performance measurement and operational and strategic planning. SAC and SRC are not fully absorbed costs and it was concluded that the model serves best as a source of indicative cost information. This thesis does not include calculating costs. Instead, the refined model together with both the theory-based and interview findings concerning the utilization of the information produced by the model will serve as a framework for the possible future development aiming at completing the model.

Developing a Comprehensive Model for Marketing Planning — Combining the Major Approaches

Mix marketing and relationships marketing are two major approaches that often form a basis for organizational marketing planning. The superiority of these approaches has been debated for long without any rational conclusion. Lately there have been studies indicating that both of the major approaches are many times used side by side in marketing planning. There have been also studies suggesting that even combining the mix marketing and relationship marketing approaches might be possible. The aim of this thesis is to provide knowledge about the usage of mix marketing and relationship marketing approaches in organizations and possibilities in combining the approaches. Also a settlement of strengths, weaknesses and risks of combining is intended to provide. The objectives were met through the literature and a case study research. In the case study, interviews were conducted in order to gain a deeper knowledge about marketing planning in various organizations. Based on this study, the combining of the major marketing approaches will be possible and even recommended when keeping in mind few aspects which might cause some troubles in the combining process.

APROS model validation in case of fast transients in a boiling water reactor

This Master´s thesis investigates the performance of the Olkiluoto 1 and 2 APROS model in case of fast transients. The thesis includes a general description of the Olkiluoto 1 and 2 nuclear power plants and of the most important safety systems. The theoretical background of the APROS code as well as the scope and the content of the Olkiluoto 1 and 2 APROS model are also described. The event sequences of the anticipated operation transients considered in the thesis are presented in detail as they will form the basis for the analysis of the APROS calculation results. The calculated fast operational transient situations comprise loss-of-load cases and two cases related to a inadvertent closure of one main steam isolation valve. As part of the thesis work, the inaccurate initial data values found in the original 1-D reactor core model were corrected. The input data needed for the creation of a more accurate 3-D core model were defined. The analysis of the APROS calculation results showed that while the main results were in good accordance with the measured plant data, also differences were detected. These differences were found to be caused by deficiencies and uncertainties related to the calculation model. According to the results the reactor core and the feedwater systems cause most of the differences between the calculated and measured values. Based on these findings, it will be possible to develop the APROS model further to make it a reliable and accurate tool for the analysis of the operational transients and possible plant modifications.

Multibody Simulation Model of the Roller Test Rig

Multibody simulation model of the roller test rig is presented in this work. The roller test rig consists of a paper machine’s tube roll supported with a hard bearing type balancing machine. The simulation model includes non-idealities that are measured from the physical structure. These non-idealities are the shell thickness variation of the roll and roundness errors of the shafts of the roll. These kinds of non-idealities are harmful since they can cause subharmonic resonances of the rotor system. In this case, the natural vibration mode of the rotor is excited when the rotation speed is a fraction of the natural frequency of the system. With the simulation model, the half critical resonance is studied in detail and a sensitivity analysis is performed by simulating several analyses with slightly different input parameters. The model is verified by comparing the simulation results with those obtained by measuring the real structure. Comparison shows that good accuracy is achieved, since equivalent responses are achieved within the error limit of the input parameters.

Simulation model of wind turbine gearbox and lubrication system

As increasing efficiency of a wind turbine gearbox, more power can be transferred from rotor blades to generator and less power is used to cause wear and heating in the gearbox. By using a simulation model, behavior of the gearbox can be studied before creating expensive prototypes. The objective of the thesis is to model a wind turbine gearbox and its lubrication system to study power losses and heat transfer inside the gearbox and to study the simulation methods of the used software. Software used to create the simulation model is Siemens LMS Imagine.Lab AMESim, which can be used to create one-dimensional mechatronic system simulation models from different fields of engineering. When combining components from different libraries it is possible to create a simulation model, which includes mechanical, thermal and hydraulic models of the gearbox. Results for mechanical, thermal, and hydraulic simulations are presented in the thesis. Due to the large scale of the wind turbine gearbox and the amount of power transmitted, power loss calculations from AMESim software are inaccurate and power losses are modelled as constant efficiency for each gear mesh. Starting values for simulation in thermal and hydraulic simulations were chosen from test measurements and from empirical study as compact and complex design of gearbox prevents accurate test measurements. In further studies to increase the accuracy of the simulation model, components used for power loss calculations needs to be modified and values for unknown variables are needed to be solved through accurate test measurements.

3D Mesh Simplification. A survey of algorithms and CAD model simplification tests

Simplification of highly detailed CAD models is an important step when CAD models are visualized or by other means utilized in augmented reality applications. Without simplification, CAD models may cause severe processing and storage is- sues especially in mobile devices. In addition, simplified models may have other advantages like better visual clarity or improved reliability when used for visual pose tracking. The geometry of CAD models is invariably presented in form of a 3D mesh. In this paper, we survey mesh simplification algorithms in general and focus especially to algorithms that can be used to simplify CAD models. We test some commonly known algorithms with real world CAD data and characterize some new CAD related simplification algorithms that have not been surveyed in previous mesh simplification reviews.

DEVELOPMENT OF A FAIR CHARGING MODEL FOR A PUBLIC DATA CENTER

The purpose of the study was to explore how a public, IT services transferor, organization, comprised of autonomous entities, can effectively develop and organize its data center cost recovery mechanisms in a fair manner. The lack of a well-defined model for charges and a cost recovery scheme could cause various problems. For example one entity may be subsidizing the costs of another entity(s). Transfer pricing is in the best interest of each autonomous entity in a CCA. While transfer pricing plays a pivotal role in the price settings of services and intangible assets, TCE focuses on the arrangement at the boundary between entities. TCE is concerned with the costs, autonomy, and cooperation issues of an organization. The theory is concern with the factors that influence intra-firm transaction costs and attempting to manifest the problems involved in the determination of the charges or prices of the transactions. This study was carried out, as a single case study, in a public organization. The organization intended to transfer the IT services of its own affiliated public entities and was in the process of establishing a municipal-joint data center. Nine semi-structured interviews, including two pilot interviews, were conducted with the experts and managers of the case company and its affiliating entities. The purpose of these interviews was to explore the charging and pricing issues of the intra-firm transactions. In order to process and summarize the findings, this study employed qualitative techniques with the multiple methods of data collection. The study, by reviewing the TCE theory and a sample of transfer pricing literature, created an IT services pricing framework as a conceptual tool for illustrating the structure of transferring costs. Antecedents and consequences of the transfer price based on TCE were developed. An explanatory fair charging model was eventually developed and suggested. The findings of the study suggested that the Chargeback system was inappropriate scheme for an organization with affiliated autonomous entities. The main contribution of the study was the application of TP methodologies in the public sphere with no tax issues consideration.