Development of Craniofacial Bone Defect Reconstruction Implant Based on Fibre-Reinforced Composite with Photopolymerisable Resin Systems. Experimental studies in vitro and in vivo.

Reconstruction of defects in the craniomaxillofacial (CMF) area has mainly been based on bone grafts or metallic fixing plates and screws. Particularly in the case of large calvarial and/or craniofacial defects caused by trauma, tumours or congenital malformations, there is a need for reliable reconstruction biomaterials, because bone grafts or metallic fixing systems do not completely fulfill the criteria for the best possible reconstruction methods in these complicated cases. In this series of studies, the usability of fibre-reinforced composite (FRC) was studied as a biostable, nonmetallic alternative material for reconstructing artificially created bone defects in frontal and calvarial areas of rabbits. The experimental part of this work describes the different stages of the product development process from the first in vitro tests with resin-impregnated fibrereinforced composites to the in vivo animal studies, in which this FRC was tested as an implant material for reconstructing different size bone defects in rabbit frontal and calvarial areas. In the first in vitro study, the FRC was polymerised in contact with bone or blood in the laboratory. The polymerised FRC samples were then incubated in water, which was analysed for residual monomer content by using high performance liquid chromatography (HPLC). It was found that this in vitro polymerisation in contact with bone and blood did not markedly increase the residual monomer leaching from the FRC. In the second in vitro study, different adhesive systems were tested in fixing the implant to bone surface. This was done to find an alternative implant fixing system to screws and pins. On the basis of this study, it was found that the surface of the calvarial bone needed both mechanical and chemical treatments before the resinimpregnated FRC could be properly fixed onto it. In three animal studies performed with rabbit frontal bone defects and critical size calvarial bone defect models, biological responses to the FRC implants were evaluated. On the basis of theseevaluations, it can be concluded that the FRC, based on E-glass (electrical glass) fibres forming a porous fibre veil enables the ingrowth of connective tissues to the inner structures of the material, as well as the bone formation and mineralization inside the fibre veil. Bone formation could be enhanced by using bioactive glass granules fixed to the FRC implants. FRC-implanted bone defects healed partly; no total healing of defects was achieved. Biological responses during the follow-up time, at a maximum of 12 weeks, to resin-impregnated composite implant seemed to depend on the polymerization time of the resin matrix of the FRC. Both of the studied resin systems used in the FRC were photopolymerised and the heat-induced postpolymerisation was used additionally.

Resource-based approach to new product development at the intersection of industries. Two case studies in telecommunications

Työn tavoitteena on selvittää mitkä ovat tärkeimmät aineettomat resurssit, joita tarvitaan teollisuuksien risteyskohdassa tapahtuvassa tuotekehityksessä. Teollisuuksien risteyskohdissa syntyvät tuotteet ovat usein radikaaleja, mikä tekee tuotteista mielenkiintoisia, paljon liiketoimintapotentiaalia tarjoavia. Tämä tutkimus lähestyy tuotekehitystä resurssipohjaisesta näkökulmasta. Myös tietämyspohjaista ja suhdepohjaista näkemystä hyödynnetään korostamaan keskittymistä aineettomiin resursseihin. Tutkimuksessa rakennetaan viitekehys, jossa tutkitaan eri resurssikategorioita. Valitut kategoriat ovat teknologiset, markkinointi-, johtamiseen ja hallinnointiin liittyvät ja suhdepohjaiset resurssit. Empiirisessä osassa tutkitaan kahta uutta tuotekonseptia, jotka ovat syntyneet teollisuuksien risteyskohdissa. Empiirisen osan tavoitteena on määritellä tutkimuksen kohteena olevia alustavia tuotekonsepteja tarkemmin ja selvittää millaisia resursseja näiden toteuttamiseen tarvitaan. Myös tarvittavien resurssien nykytila selvitetään ja pohditaan tulisiko puuttuvia resursseja kehittää yrityksen sisällä vai hankkia ne ulkopuolelta. Tutkimus toteutettiin asiantuntijahaastatteluin. Kahden tapaustutkimuksen perusteella näyttäisi siltä, että suhdepohjaiset resurssit ovat erittäin tärkeitä teollisuuksien risteyskohdissa tapahtuvassa tuotekehityksessä. Myös teknologiset resurssit ovat tärkeitä. Markkinointiresurssien tärkeys riippuu lopullisesta tuotekonseptista, kun taas johtamiseen ja kehittämiseen liittyvät resurssit ovat tärkeitänäiden konseptien luomisessa.

Brain imaging studies in severe somatization

Somatization was described 4000 years ago but the pathophysiology of the, phenomenon is unknown. The aim of this investigation was to explore whether central nervous system (CNS) pathology is associated with severe somatization which was operationalized as somatization disorder (SD) and undifferentiated somatoform disorder. The study sample consisted of severely somatizing people who were included into the study after a multi-phase screening procedure in order to exclude psychiatric comorbidities and physical illnesses. Diagnosis of somatization disorder or undifferentiated sofatoform disorder were set according to Diagnostic and Statistical Manual of Mental Disorders 4th ed. (DSM-IV). The first study explored the regional cerebral metabolic rate of glucose (rCMRGlc) in severely somatizing females and found it to be reduced in several regions of the brain compared to healthy controls. The second study observed brain morphology with magnetic resonance imaging (MRI) based on the findings from the first study and showed enlarged caudate nuclei in somatizing women compared to healthy volunteers. The third study investigated temperament factors and brain metabolism, and their association with severe somatization. Low caudate and putamen metabolism, low novelty seeking as well as high harm avoidance were found to be associated with severe somatization in women, reduced caudate metabolism having the strongest association. The last study is a report of man with left-side gradient of multiple symptoms of unknown origin in the body. The examination revealed a hypermetabolic nucleus putamen on the contralateral side. All the main results reported in these four articles are original findings. The results suggest that CNS pathology is involved in the pathophysiology of severe somatization.

Non-resorbable glass fibre-reinforced composite with porous surface as bone substitute material: Experimental studies in vitro and in vivo focused on bone-implant interface

The development of load-bearing osseous implant with desired mechanical and surface properties in order to promote incorporation with bone and to eliminate risk of bone resorption and implant failure is a very challenging task. Bone formation and resoption processes depend on the mechanical environment. Certain stress/strain conditions are required to promote new bone growth and to prevent bone mass loss. Conventional metallic implants with high stiffness carry most of the load and the surrounding bone becomes virtually unloaded and inactive. Fibre-reinforced composites offer an interesting alternative to metallic implants, because their mechanical properties can be tailored to be equal to those of bone, by the careful selection of matrix polymer, type of fibres, fibre volume fraction, orientation and length. Successful load transfer at bone-implant interface requires proper fixation between the bone and implant. One promising method to promote fixation is to prepare implants with porous surface. Bone ingrowth into porous surface structure stabilises the system and improves clinical success of the implant. The experimental part of this work was focused on polymethyl methacrylate (PMMA) -based composites with dense load-bearing core and porous surface. Three-dimensionally randomly orientated chopped glass fibres were used to reinforce the composite. A method to fabricate those composites was developed by a solvent treatment technique and some characterisations concerning the functionality of the surface structure were made in vitro and in vivo. Scanning electron microscope observations revealed that the pore size and interconnective porous architecture of the surface layer of the fibre-reinforced composite (FRC) could be optimal for bone ingrowth. Microhardness measurements showed that the solvent treatment did not have an effect on the mechanical properties of the load-bearing core. A push-out test, using dental stone as a bone model material, revealed that short glass fibre-reinforced porous surface layer is strong enough to carry load. Unreacted monomers can cause the chemical necrosis of the tissue, but the levels of leachable resisidual monomers were considerably lower than those found in chemically cured fibre-reinforced dentures and in modified acrylic bone cements. Animal experiments proved that surface porous FRC implant can enhance fixation between bone and FRC. New bone ingrowth into the pores was detected and strong interlocking between bone and the implant was achieved.

Brain Dopamine and Serotonin Receptors in the Perception of Pain. Positron Emission Tomography Studies in Healthy Subjects

The role of dopamine and serotonin in spinal pain regulation is well established. However, little is known concerning the role of brain dopamine and serotonin in the perception of pain in humans. The aim of this study was to assess the potential role of brain dopamine and serotonin in determining experimental pain sensitivity in humans using positron emission tomography (PET) and psychophysical methods. A total of 39 healthy subjects participated in the study, and PET imaging was performed to assess brain dopamine D2/D3 and serotonin 5-HT_1A receptor availability. In a separate session, sensitivity to pain and touch was assessed with traditional psychophysical methods, allowing the evaluation of potential associations between D2/D3 and 5-HT_1A binding and psychophysical responses. The subjects’ responses were also analyzed according to Signal Detection Theory, which enables separate assessment of the subject’s discriminative capacity (sensory factor) and response criterion (non-sensory factor). The study found that the D2/D3 receptor binding in the right putamen was inversely correlated with pain threshold and response criterion. 5-HT_1A binding in cingulate cortex, inferior temporal gyrus and medial prefrontal cortex was inversely correlated with discriminative capacity for touch. Additionally, the response criterion for pain and intensity rating of suprathreshold pain were inversely correlated with 5-HT_1A binding in multiple brain areas. The results suggest that brain D2/D3 receptors and 5-HT_1A receptors modulate sensitivity to pain and that the pain modulatory effects may, at least partly, be attributed to influences on the response criterion. 5-HT_1A receptors are also involved in the regulation of touch by having an effect on discriminative capacity.

Possibilities and challenges of longitudinal studies in operations management

Longitudinal studies are quite rare in the area of Operations Management. One reason might be the time needed to conduct such studies, and then the lack of experience and real-life examples and results. The aim of the thesis is to examine longitudinal studies in the area of OM and the possible advantages, challenges and pitfalls of such studies. A longitudinal benchmarking study, Made in Finland, was analyzed in terms of the study methodology and its outcomes. The timeline of this longitudinal study is interesting. The first study was made in 1993, the second in 2004 and the third in 2010. Between these studies some major changes occurred in the Finnish business environment. Between the first and second studies, Finland joined the ETA and the EU, and globalization started with the rise of the Internet era, while between the second and third studies financial turmoil started in 2007. The sample and cases used in this study were originally 23 manufacturing sites in Finland. These sites were interviewed in 1993, in 2004 and 2010. One important and interesting aspect is that all the original sites participated in 2004, and 19 sites were still able to participate in 2010. Four sites had been closed and/or moved abroad. All of this gave a good opportunity to study the changes that occurred in the Finnish manufacturing sites and their environment, and how they reacted to these changes, and the effects on their performance. It is very seldom, if ever, that the same manufacturing sites have been studied in a longitudinal setting by using three data points. The results of this study are thus unique, and the experience gained is valuable for practitioners.

Studies in offset ink setting

The offset printing process is complex and involves the meeting of two essentially complex materials, printing ink and paper, upon which the final product is formed. It can therefore be expected that a multitude of chemical and physical interactions and mechanisms take place at the ink-paper interface. Interactions between ink and paper are of interest to both the papermakers and ink producers, as they wish to achieve better quality in the final product. The objective of this work is to clarify the combined influence of paper coating structure, printing ink and fountain solution on ink setting and the problems related to ink setting. A further aim is to identify the mechanisms that influence ink setting problems, and to be able to counteract them by changing properties of the coating layer or by changing the properties of the ink. The work carried out for this thesis included use of many techniques ranging from standard paper and printability tests to advanced optical techniques for detection of ink filaments during ink levelling. Modern imaging methods were applied for assessment of ink filament remain sizes and distribution of ink components inside pigment coating layers. Gravimetric filtration method and assessment of print rub using Ink-Surface-Interaction-Tester (ISIT) were utilized to study the influence of ink properties on ink setting. The chemical interactions were observed with the help of modified thin layer chromatography and contact angle measurements using both conventional and high speed imaging. The results of the papers in this thesis link the press operational parameters to filament sizes and show the influence of these parameters to filament size distribution. The relative importance between the press operation parameters was shown to vary. The size distribution of filaments is important in predicting the ink setting behaviour, which was highlighted by the dynamic gloss and ink setting studies. Prediction of ink setting behaviour was also further improved by use of separate permeability factors for different ink types in connection to filtration equations. The roles of ink components were studied in connection to ink absorption and mechanism of print rub. Total solids content and ratio of linseed oil to mineral oil were found to determine the degree of print rub on coated papers. Wax addition improved print rub resistance, but would not decrease print rub as much as lowering the total solids content in the ink. Linseed oil was shown to absorb into pigment coating pores by mechanism of adsorption to pore walls, which highlights the need for sufficient pore surface area for improved chromatographic separation of ink components. These results should help press operators, suppliers of printing presses, papermakers and suppliers to papermakers, to better understand the material and operating conditions of the press as it relates to various print quality issues. Even though paper is in competition with electronic media, high quality printed products are still in demand. The results should provide useful information for this segment of the industry.

Web-Based Extension Studies in Medical Calculation

Nordic forum for nursing teachers. Wednesday - Friday 9-11 November 2011 Ounasvaara Campus School of Heath Care and Sports Rovaniemi University of Applied Sciences