Ultrafiltration of pulp mill bleaching effluents

Main objective of this research was to find suitable polymeric ultrafiltration membranes with high retentions, good capacities and low fouling tendencies for the E2- and EP-effluent ultrafiltration. Purpose was to treat alkaline bleaching effluents with ultrafiltration in a way that permeates of the filtrations could be recycled back to process and the consumption of fresh water in the pulp mill could be reduced significantly. In the theoretical part of this work the challenges set by the pulp and paper indus-try processes for membranes were examined. An overview of the membrane tech-nology in the pulp industry was also provided. In addition process conditions in the chemical pulp bleaching and properties of bleaching effluents were discussed in literature study. In experimental part the E2- and EP-stage bleaching effluents from Stora Enso Imatra kraft pulp mill were ultrafiltered with CR250- and CR200-filters. Suitable membranes for ultrafiltration were chosen after screening experiments. Concentra-tion experiment was made for the E2-effluent in order to estimate water saving potential. The E2-effluent was finally ultrafiltered in the pulp mill in order to test the feasibility of ultrafiltration in a real industrial environment. Good membrane for the EP-effluent ultrafiltration based on the EP-screening ex-periments was polyethersulfone membrane UP020 with cut-off value of 20 000 Da. Polysulfone membrane UFX05 with cut-off value of 5 000 Da was promising membrane for the ultrafiltration of the E2-effluent. Based on the concentration filtration of the E2-effluent with UFX05 membrane the water saving potential could be 2.2 m3/Adt for the industrial scale ultrafiltration process. Retention re-sults, such as average COD retention of 60 %, from the trial filtration at the pulp mill with UFX05 membrane were modest compared to the screening experiments, where average COD retention was 75 %. Therefore tighter ultrafiltration mem-branes should be tested for the ultrafiltration of the E2-effluent. The UP020 mem-brane seemed to be suitable for the ultrafiltration of the EP-effluent however con-centration and pilot scale ultrafiltration experiments are needed to verify this.

Puuperäisten biomassahydrolysaattien likaamien membraanien pesu

Tässä diplomityössä tutkittiin biomassahydrolysaatilla liattujen ultrasuodatusmembraanien pesua. Työn kirjallisuusosassa käsitellään membraanien likaantumista ja pesua, puuperäistä biomassahydrolysaattia sekä biomassahydrolysaatin suodatusta membraaneilla ja membraanien karakterisointia. Kokeellisessa osassa tutkittiin pesuaineiden vaikutusta koivuhydrolysaatilla liattujen membraanien peseytyvyyteen. Käytetyt ultrasuodatusmembraanit olivat Alfa Lavalin UFX5 ja ETNA01PP. Membraanien pesussa käytettiin Ecolabin entsymaattisia P3-ultrasil 53 ja P3-ultrasil 67 pesuaineita yhdessä emäksisen P3-ultrasil 69 pesuaineen kanssa sekä hapanta P3-ultrasil 75 pesuainetta. Lisäksi emäksisiä P3-ultrasil 110, P3-ultrasil 112 ja P3-ultrasil 115 pesuaineita. Emäksisten pesujen tehokkuutta vertailtiin pelkällä natriumhydroksidilla tehtyyn pesuun. Membraanien likaantumista arvioitiin mittaamalla puhtaan veden vuota ennen ja jälkeen likaantumissuodatuksen ja laskemalla niiden vuoarvojen erotus. Samalla tavalla arvioitiin pesuaineiden vaikutusta membraanin peseytyvyyteen. Lisäksi peseytyvyyttä arvioitiin FTIR–analyyseillä, kontaktikulmamittauksilla ja membraanin sisältämän ligniinin värjäyksellä. Tutkimuksissa havaittiin, että koivuhydrolysaatilla liatuille UFX5 membraaneille vesivuon sekä FTIR–spektrin muuttumisen perusteella sopii parhaiten emäksisen ja happaman pesuaineen kaksivaiheinen pesu. Kontaktikulman palautumisen perusteella parhaiten sopi pelkällä emäksisellä P3-Ultrasil 115 tehty pesu. Ligniiniä parhaiten, mikroskooppiin liitetyllä kameralla otettujen kuvien perusteella, poisti entsymaattinen P3-ultrasil 67, mutta tämä samalla modifioi membraanin pintaa. Tässä tutkimuksessa havaittiin, että emäksinen ja entsymaattinen pesuaine pesevät melko hyvin koivuhydrolysaatilla liattuja membraaneja. Lisäksi havaittiin, että ligniini tunkeutuu suodatuksissa membraanin sisään, joten pelkkä pesuaineen kierrättäminen laitteistossa ei riitä vaan tarvitaan paineellista pesua.

Fouling, prevention of fouling, and clearing in filtration

In this thesis fouling of conventional filter fabrics and membranes was studied. In the beginning of the thesis fouling and how it can be measured and predicted is reviewed. Information on different methods on how fouling canbe decreased or cleaned away is also given. The experimental part is divided into two sections; fabric filtration and membrane filtration. Fouling of the filter fabrics was studied with silica or cupper slurries and fouling of the membranes was studied with pulp and paper mill waters. The fouled filter materials were characterised according to many different methods. The most useful way to observe fouling is to measure the changes in the permeate flux. Fouling can also be seen visually e.g. with scanning electron microscopy. Consequently, also the reason for the fouling in question might be found. Different filtration characteristics affect fouling e.g. as the filtration pressure was increased it did not have much influence on the permeate flux, but the pressure caused the membrane to get fouled faster. Also, an increase of shear rate on the membrane surface decreased fouling. Different pretreatment methods for the effluent were tested in membrane filtration to decrease fouling. The tested methods; biological treatment, ozonation, enzymatic treatment and flocculation, did not have a clear influence on the fouling of the membrane, but e.g. a biological treatment combined with ultrafiltration made the tested groundwood mill circulation water purer than ultrafiltration alone.

Development of a Ceramic Membrane Filtration Equipment and Its Applicability for Different Wastewaters

In this thesis the membrane filtration equipment for plate type ceramic membranes was developed based on filtration results achieved with different kinds of wastewaters. The experiments were mainly made with pulp and board mill wastewaters, but some experiments were also made with a bore well water and a stone cutting mine wastewater. The ceramicmembranes used were alpha-alumina membranes with a pore size of 100 nm. Some ofthe membranes were coated with a gamma-alumina layer to reduce the membrane pore size to 10 nm, and some of them were modified with different metal oxides in order to change the surface properties of the membranes. The effects of operationparameters, such as cross-flow velocity, filtration pressure and backflushing on filtration performance were studied. The measured parameters were the permeateflux, the quality of the permeate, as well as the fouling tendency of the membrane. A dynamic membrane or a cake layer forming on top of the membrane was observed to decrease the flux and increase separa-tion of certain substances, especially at low cross-flow velocities. When the cross-flow velocities were increased the membrane properties became more important. Backflushing could also be used to decrease the thickness of the cake layer and thus it improved the permeate flux. However, backflushing can lead to a reduction of retentions in cases where the cake layer is improving them. The wastewater quality was important for the thickness of the dynamic membrane and the membrane pore size influenced the permeate flux. In general, the optimization of operation conditions is very important for the successful operation of a membrane filtration system. The filtration equipment with a reasonable range of operational conditions is necessary, especiallywhen different kinds of wastewaters are treated. This should be taken into account already in the development stage of a filtration equipment.

Critical flux and fouling in ultrafiltration of proteins

In this thesis different parameters influencing critical flux in protein ultrafiltration and membrane foul-ing were studied. Short reviews of proteins, cross-flow ultrafiltration, flux decline and criticalflux and the basic theory of Partial Least Square analysis (PLS) are given at the beginning. The experiments were mainly performed using dilute solutions of globular proteins, commercial polymeric membranes and laboratory scale apparatuses. Fouling was studied by flux, streaming potential and FTIR-ATR measurements. Critical flux was evaluated by different kinds of stepwise procedures and by both con-stant pressure and constant flux methods. The critical flux was affected by transmembrane pressure, flow velocity, protein concentration, mem-brane hydrophobicity and protein and membrane charges. Generally, the lowest critical fluxes were obtained at the isoelectric points of the protein and the highest in the presence of electrostatic repulsion between the membrane surface and the protein molecules. In the laminar flow regime the critical flux increased with flow velocity, but not any more above this region. An increase in concentration de-creased the critical flux. Hydrophobic membranes showed fouling in all charge conditionsand, furthermore, especially at the beginning of the experiment even at very low transmembrane pressures. Fouling of these membranes was thought to be due to protein adsorption by hydrophobic interactions. The hydrophilic membranes used suffered more from reversible fouling and concentration polarisation than from irreversible foul-ing. They became fouled at higher transmembrane pressures becauseof pore blocking. In this thesis some new aspects on critical flux are presented that are important for ultrafiltration and fractionation of proteins.

Recovery of Hemicelluloses from Wood Hydrolysates by Membrane Filtration

Hemicelluloses are among the most important natural resources that contain polysaccharides. In this study the separation and purification of hemicelluloses from water extraction liquors containing wood hemicelluloses, lignin compounds and monosaccharide by using membrane filtration was investigated. The isolation of the hemicelluloses from the wood hydrolysates was performed in two steps: concentration of high molar mass hemicelluloses by ultrafiltration and separation of low molar mass hemicelluloses from monomeric sugars using tight ultrafiltration membranes. The purification of the retained hemicelluloses was performed by diafiltration. During the filtration experiments, the permeate flux through ultrafiltration and tight ultrafiltration membranes was relatively high. The fouling ability of the used membranes was relatively low. In our experiments, the retention of hemicelluloses using two filtration steps was almost complete. The separation of monosaccharides from hemicelluloses was relatively high and the purification of hemicelluloses by diafiltration was highly efficient. The separation of lignin from hemicelluloses was partially achieved. Diafiltration showed potential to purify retained hemicelluloses from lignin and other organics. The best separation of lignin from hemicelluloses in the first filtration step was obtained using the UC005 membrane. The GE-5 and ETNA01PP membranes showed potential to purify and separate lignin from hemicelluloses. However, the feed solution of the second filtration stages (from different ultrafiltration membranes) affected the permeate flux and the separation of various extracted compounds from hemicelluloses. The GE-5 and ETNA01PP membranes gave the efficient purification of the hemicelluloses when using diafiltration. Separation of degraded xylan from glucomannan (primary spruce hemicelluloses) was also possible using membrane filtration. The best separation was achieved using the GE-5 membrane. The retention of glucomannan was three times higher than xylan retention.

Fouling management and retention in nanofiltration of integrated paper mill effluents

Nanofiltration performance was studied with effluents from the pulp and paper industry and with model substances. The effect of filtration conditions and membrane properties on nanofiltration flux, retention, and fouling was investigated. Generally, the aim was to determine the parameters that influence nanofiltration efficiency and study how to carry out nanofiltration without fouling by controlling these parameters. The retentions of the nanofiltration membranes studied were considerably higher than those of tight ultrafiltration membranes, and the permeate fluxes obtained were approximately the same as those of tight ultrafiltration membranes. Generally, about 80% retentions of total carbon and conductivity were obtained during the nanofiltration experiments. Depending on the membrane and the filtration conditions, the retentions of monovalent ions (chloride) were between 80 and 95% in the nanofiltrations. An increase in pH improved retentions considerably and also the flux to some degree. An increase in pressure improved retention, whereas an increase in temperature decreased retention if the membrane retained the solute by the solution diffusion mechanism. In this study, more open membranes fouled more than tighter membranes due to higher concentration polarization and plugging of the membrane material. More irreversible fouling was measured for hydrophobic membranes. Electrostatic repulsion between the membrane and the components in the solution reduced fouling but did not completely prevent it with the hydrophobic membranes. Nanofiltration could be carried out without fouling, at least with the laboratory scale apparatus used here when the flux was below the critical flux. Model substances had a strong form of the critical flux, but the effluents had only a weak form of the critical flux. With the effluents, some fouling always occurred immediately when the filtration was started. However, if the flux was below the critical flux, further fouling was not observed. The flow velocity and pH were probably the most important parameters, along with the membrane properties, that influenced the critical flux. Precleaning of the membranes had only a small effect on the critical flux and retentions, but it improved the permeability of the membranes significantly.

Pretreatment in membrane filtration of wood hydrolysate

Interest in recovery of valuable components from process streams has increased in recent years. Purpose of biorefinery is to utilize components that otherwise would go to waste. Hemicelluloses, for example, could be utilized in production of many valuable products. One possible way to separate and fractionate hemicelluloses is membrane filtration. In the literature part of this work membrane fouling in filtration processes of pulp and paper process- and wastewaters was investigated. Especially purpose was to find out the possible fouling compounds, after which facilities to remove or modify such components less harmful were studied. In the experimental part different pretreatment methods, mainly to remove or degrade lignin from wood hydrolysate, were studied. In addition, concentration of hemicelluloses and separation from lignin were examined with two ultrafiltration membranes; UFX5 and RC70PP. Changes in feed solution, filtration capacity and fouling of membranes were used to evaluate the effects of pretreatment methods. Changes in hydrolysate composition were observed with different analysis methods. Filtration of hydrolysate proved to be challenging, especially with the UFX5 membrane. The more hydrophilic RC70PP membrane did not seem to be fouled as severely as the UFX5 membrane, according to pure water flux measurements. The UFX5 membrane retained hemicelluloses rather well, but problems arose from rapid flux decline resulting from concentration polarization and fouling of membrane. Most effective pretreatment methods in the case with the UFX5 membrane proved to be prefiltration with the RC70PP membrane, activated carbon adsorption and photocatalytic oxidation using titanium dioxide and UV radiation. An additional experiment with PHW extract showed that pulsed corona discharge treatment degraded lignin quite efficiently and thus improved filtration capacity remarkably, even over six times compared to the filtration with untreated extract.

Online Ultrasound Measurements of Membrane Compaction

There are several filtration applications in the pulp and paper industry where the capacity and cost-effectiveness of processes are of importance. Ultrafiltration is used to clean process water. Ultrafiltration is a membrane process that separates a certain component or compound from a liquid stream. The pressure difference across the membrane sieves macromolecules smaller than 0.001-0.02 μm through the membrane. When optimizing the filtration process capacity, online information about the conditions of the membrane is needed. Fouling and compaction of the membrane both affect the capacity of the filtration process. In fouling a “cake” layer starts to build on the surface of the membrane. This layer blocks the molecules from sieving through the membrane thereby decreasing the yield of the process. In compaction of the membrane the structure is flattened out because of the high pressure applied. The higher pressure increases the capacity but may damage the structure of the membrane permanently. Information about the compaction is needed to effectively operate the filters. The objective of this study was to develop an accurate system for online monitoring of the condition of the membrane using ultrasound reflectometry. Measurements of ultrafiltration membrane compaction were made successfully utilizing ultrasound. The results were confirmed by permeate flux decline, measurements of compaction with a micrometer, mechanical compaction using a hydraulic piston and a scanning electron microscope (SEM). The scientific contribution of this thesis is to introduce a secondary ultrasound transducer to determine the speed of sound in the fluid used. The speed of sound is highly dependent on the temperature and pressure used in the filters. When the exact speed of sound is obtained by the reference transducer, the effect of temperature and pressure is eliminated. This speed is then used to calculate the distances with a higher accuracy. As the accuracy or the resolution of the ultrasound measurement is increased, the method can be applied to a higher amount of applications especially for processes where fouling layers are thinner because of smaller macromolecules. With the help of the transducer, membrane compaction of 13 μm was measured in the pressure of 5 bars. The results were verified with the permeate flux decline, which indicated that compaction had taken place. The measurements of compaction with a micrometer showed compaction of 23–26 μm. The results are in the same range and confirm the compaction. Mechanical compaction measurements were made using a hydraulic piston, and the result was the same 13 μm as obtained by applying the ultrasound time domain reflectometry (UTDR). A scanning electron microscope (SEM) was used to study the structure of the samples before and after the compaction.

Utilisation of magnetic field in membrane filtration

As it is known, the major problem of membrane filtration is fouling of membrane during the filtration process. There are a lot of methods to prevent or reduce fouling. One very little studied method is applying of magnetic field in membrane filtration. Magnetic field has such advantages as bulk, contact free, nondestructive impact on the sample, thus it can be combined with different types of processes. In addition, the use of magnetic fields has given positive results in various areas of science and life. So, the present thesis is devoted to the research of influence of magnetic field on performances of nanofiltration. In the literature part of the thesis a short description of membrane process and mechanism of reorientation of nanoparticals in magnetic field is presented. The utilization of magnetic field in different spheres of life, in general, and membrane area, in particular, is represented. In the experimental part the influence of magnetic field created by two permanent magnets on filtration of two solutions (citric acid and sodium dodecyl sulfate) was investigated. Factors, which affect on the impact of magnetic field was estimated. The effect of magnetic field was evaluated by measuring a change of pure water permeability after the filtration of model solution. This work demonstrated that direction of magnetic field and the type of molecules of filtered solution has significant effect to the efficiency of nanofiltration. Utilization of magnetic field might increase retention of membrane and flux through membrane and reduce fouling.

Identification of extractives and polysaccharides as foulants in membrane filtration of pulp and paper mill effluents

The search for new renewable materials has intensified in recent years. Pulp and paper mill process streams contain a number of potential compounds which could be used in biofuel production and as raw materials in the chemical, food and pharmaceutical industries. Prior to utilization, these compounds require separation from other compounds present in the process stream. One feasible separation technique is membrane filtration but to some extent, fouling still limits its implementation in pulp and paper mill applications. To mitigate fouling and its effects, foulants and their fouling mechanisms need to be well understood. This thesis evaluates fouling in filtration of pulp and paper mill process streams by means of polysaccharide model substance filtrations and by development of a procedure to analyze and identify potential foulants, i.e. wood extractives and carbohydrates, from fouled membranes. The model solution filtration results demonstrate that each polysaccharide has its own fouling mechanism, which also depends on the membrane characteristics. Polysaccharides may foul the membranes by adsorption and/or by gel/cake layer formation on the membrane surface. Moreover, the polysaccharides interact, which makes fouling evaluation of certain compound groups very challenging. Novel methods to identify wood extractive and polysaccharide foulants are developed in this thesis. The results show that it is possible to extract and identify wood extractives from membranes fouled in filtration of pulp and paper millstreams. The most effective solvent was found to be acetone:water (9:1 v/v) because it extracted both lipophilic extractives and lignans at high amounts from the fouled membranes and it was also non-destructive for the membrane materials. One hour of extraction was enough to extract wood extractives at high amounts for membrane samples with an area of 0.008 m2. If only qualitative knowledge of wood extractives is needed a simplified extraction procedure can be used. Adsorption was the main fouling mechanism in extractives-induced fouling and dissolved fatty and resin acids were mostly the reason for the fouling; colloidal fouling was negligible. Both process water and membrane characteristics affected extractives-induced fouling. In general, the more hydrophilic regenerated cellulose (RC) membrane fouled less that the more hydrophobic polyethersulfone (PES) and polyamide (PA) membranes independent of the process water used. Monosaccharide and uronic acid units could also be identified from the fouled synthetic polymeric membranes. It was impossible to analyze all monosaccharide units from the RC membrane because the analysis result obtained contained degraded membrane material. One of the fouling mechanisms of carbohydrates was adsorption. Carbohydrates were not potential adsorptive foulants to the sameextent as wood extractives because their amount in the fouled membranes was found to be significantly lower than the amount of wood extractives.

Recovery of biomass-derived valuable compounds using chromatographic and membrane separations

Utilization of biomass-based raw materials for the production of chemicals and materials is gaining an increasing interest. Due to the complex nature of biomass, a major challenge in its refining is the development of efficient fractionation and purification processes. Preparative chromatography and membrane filtration are selective, energy-efficient separation techniques which offer a great potential for biorefinery applications. Both of these techniques have been widely studied. On the other hand, only few process concepts that combine the two methods have been presented in the literature. The aim of this thesis was to find the possible synergetic effects provided by combining chromatographic and membrane separations, with a particular interest in biorefinery separation processes. Such knowledge could be used in the development of new, more efficient separation processes for isolating valuable compounds from complex feed solutions that are typical for the biorefinery environment. Separation techniques can be combined in various ways, from simple sequential coupling arrangements to fully-integrated hybrid processes. In this work, different types of combined separation processes as well as conventional chromatographic separation processes were studied for separating small molecules such as sugars and acids from biomass hydrolysates and spent pulping liquors. The combination of chromatographic and membrane separation was found capable of recovering high-purity products from complex solutions. For example, hydroxy acids of black liquor were successfully recovered using a novel multistep process based on ultrafiltration and size-exclusion chromatography. Unlike any other separation process earlier suggested for this challenging separation task, the new process concept does not require acidification pretreatment, and thus it could be more readily integrated into a pulp-mill biorefinery. In addition to the combined separation processes, steady-state recycling chromatography, which has earlier been studied for small-scale separations of high-value compounds only, was found a promising process alternative for biorefinery applications. In comparison to conventional batch chromatography, recycling chromatography provided higher product purity, increased the production rate and reduced the chemical consumption in the separation of monosaccharides from biomass hydrolysates. In addition, a significant further improvement in the process performance was obtained when a membrane filtration unit was integrated with recycling chromatography. In the light of the results of this work, separation processes based on combining membrane and chromatographic separations could be effectively applied for different biorefinery applications. The main challenge remains in the development of inexpensive separation materials which are resistant towards harsh process conditions and fouling.

Membrane development for oil contaminated water treatments

The aim of this Master’s thesis study was to develop a membrane for oil contaminated water treatments. Oily wastewaters are a big problem to environment and therefore it is important to find an efficient method for their treatment. There are several treatment methods, but one of the most promising methods is membrane filtration. In the theoretical part of this study the membrane technology and polymeric membrane preparation with phase inversion and membrane modification methods was discussed. It was also told about the most important properties of the membranes. Oily waters, their treatment methods and oily wastewater sources were discussed more specifically. In the experimental part membranes from cellulose acetate were prepared and membranes were modified with two different methods. Modification methods were surface modification and polymer mixing. The modification purpose was to make membranes more hydrophilic and increase surface charge, which can reduce fouling. Membranes were characterized by determining zeta potential, contact angle, oil retention, pure water permeability, pressure-normalized flux and fouling. It were used both synthetic and real spent oil-water emulsion in membrane filtration. Surface modification resulted membranes, which had better properties than unmodified membrane. The amount of substance used in surface modification affected a lot to membrane properties, so it would be necessary to try different amounts of substance to develop the best membrane for oil-water emulsion treatment.

Heran nanosuodatus: raaka-ainekoostumuksen ja prosessiolosuhteiden vaikutus kalvon likaantumiseen

Työssä tutkittiin kalvon likaantumiseen vaikuttavia tekijöitä juoksuteheran nanosuodatuksessa. Tutkimuksessa käytettiin Desal-5 DK kalvoa. Heran nanosuodatukset suoritettiin yhden spiraalimoduulin käsittävää pilot -mittakaavaista suodatuslaitteistoa käyttäen. Työssä selvitettiin suodatettavan heran iän, pastörointilämpötilan, pH:n, suodatuslämpötilan sekäheran sisältämän juustopölyn, lisätyn kalsiumkloridin määrän ja rasvan laadun vaikutusta permeaattivuohon. Jokaista tekijää testattiin kahta eri muuttujaa käyttäen. Työssä tutkittiin myös kahden samanlaisen kalvon välisiä läpäisevyyseroja. Heran pastörointilämpötila, pH ja suodatuslämpötila osoittautuivat kalvon likaantumisen kannalta tärkeimmiksi tekijöiksi heran nanosuodatuksessa. Permeaattivuo oli korkeampi suodatettaessa 74 ºC lämpötilassa pastöroitua heraa, kuin 78 ºC lämpötilassa pastöroitua. Hera suodattui paremmin silloin, kunsen pH oli säädetty 5,8:aan, kuin heran pH:n ollessa säädettynä 5,2:een. Suodatettaessa 18 ºC suodatuslämpötilaan temperoitua heraa havaittiin korkeampi permeaattivuo kuin 12 ºC lämpötilaan termostoitua heraa suodatettaessa. Heran sisältämä pölyn määrä, rasvan laatu ja heran ikä havaittiin tilastollisesti merkityksettömiksi tekijöiksi sekä heran suodattuvuuden, että kalvon puhdistuvuuden kannalta. Kalsiumkloridin lisääminen heraan ennen suodatusta vaikuttivain kalvon suodatuksen jälkeiseen peseytyvyyteen. Kalvo puhdistui paremmin, kun kalsiumkloridia ei oltu lisätty heraan ennen suodatusta. Desal-5 DK kalvojen läpäisevyyseroja tutkittiin suodattamalla glukoosia ja natriumkloridia sisältävää malliaineliuosta kummankin vertailtavan kalvon läpi. Kokeissa havaittiin, että toista nanosuodatuskalvoa käytettäessä mitatut vesivuot olivat jopa 100 % korkeampia kuin vertailukalvoa käytettäessä mitatut. Myös glukoosin kalvolle pidättymisessä havaittiin eroja kalvojen välillä. Syyksi suuriin läpäisevyyseroihin arveltiin riittämätöntä kalvojen esikäsittelyä ennen malliainekokeen suorittamista, joten ei pystytty arvioimaan, oliko kalvojen läpäisevyyksissävalmistusprosessista johtuvia eroja.

Effect of physico-chemical conditions and operating parameters on flux and retention of different components in ultrafiltration and nanofiltration fractionation of sweet whey

Tässä väitöstutkimuksessa tutkittiin fysikaaliskemiallisten olosuhteiden ja toimintaparametrien vaikutusta juustoheran fraktiointiin. Kirjallisuusosassa on käsitelty heran ympäristövaikutusta, heran hyödyntämistä ja heran käsittelyä kalvotekniikalla. Kokeellinen osa on jaettu kahteen osaan, joista ensimmäinen käsittelee ultrasuodatusta ja toinen nanosuodatusta juustoheran fraktioinnissa. Ultrasuodatuskalvon valinta tehtiin perustuen kalvon cut-off lukuun, joka oli määritetty polyetyleeniglykoliliuoksilla olosuhteissa, joissa konsentraatiopolariosaatioei häiritse mittausta. Kriittisen vuon konseptia käytettiin sopivan proteiinikonsentraation löytämiseksi ultrasuodatuskokeisiin, koska heraproteiinit ovat tunnetusti kalvoa likaavia aineita. Ultrasuodatuskokeissa tutkittiin heran eri komponenttien suodattumista kalvon läpi ja siihen vaikuttavia ominaisuuksia. Herapermeaattien peptidifraktiot analysoitiin kokoekskluusiokromatografialla ja MALDI-TOF massaspektrometrillä. Kokeissa käytettävien nanosuodatuskalvojen keskimääräinen huokoskoko analysoitiin neutraaleilla liukoisilla aineilla ja zeta-potentiaalit virtauspotentiaalimittauksilla. Aminohappoja käytettiin malliaineina tutkittaessa huokoskoon ja varauksen merkitystä erotuksessa. Aminohappojen retentioon vaikuttivat pH ja liuoksen ionivahvuus sekä molekyylien väliset vuorovaikutukset. Heran ultrasuodatuksessa tuotettu permeaatti, joka sisälsi pieniä peptidejä, laktoosia ja suoloja, nanosuodatettiin happamassa ja emäksisessä pH:ssa. Emäksisissä oloissa tehdyssä nanosuodatuksessa foulaantumista tapahtui vähemmän ja permeaattivuo oli parempi. Emäksisissä oloissa myös selektiivisyys laktoosin erotuksessa peptideistä oli parempi verrattuna selektiivisyyteen happamissa oloissa.