Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Development of a Business Model that Supports Mobile Value-Added Services Market Creation in Emerging Countries

Tutkielman tavoitteena on luoda liiketoimintamalli, joka tukee langattomien matkaviestintäpalveluiden markkinoiden luomista kehittyvillä markkinoilla. Teoreettinen osa tarkastelee langattomien matkaviestintäpalveluiden liiketoimintamallin kehittämisen tärkeimpiä elementtejä CIS maissa. Teoreettisen kappaleen tuloksena saadaan puitteet, jonka avulla liiketoimintamalli matkaviestintäpalveluille voidaan kehittää. Tutkielman empiirinen osa on toteutettu case tutkimuksena, jonka tavoitteena on ollut langattomien matkaviestintäpalvelujen markkinoiden luominen CIS maissa. Pääasiallinen empiirisen tiedon lähde on ollut teemahaastattelut. Tuloksena saatuja empiirisen osan tietoja verrataan teoriakappaleen vastaaviin tuloksiin Tulokset osoittavat, että radikaalin korkean teknologian innovaation markkinoiden luominen on hidas prosessi, joka vaatii kärsivällisyyttä yritykseltä. Markkinoiden, teknologian ja strategian epävarmuustekijät tuovat epävarmuutta kehittyvälle toimialalle ja markkinoille, joka vaikeuttaa liiketoimintamallin kehittämistä. Tärkein tekijä on palvelujen markkinointi ennemmin kuin teknologian. Avain kyvykkyys markkinoiden luomisessa on oppiminen, ei tietäminen.

Brown algal phlorotannins: Improving and applying chemical methods

Phlorotannins are the least studied group of tannins and are found only in brown algae. Hitherto the roles of phlorotannins, e.g. in plant-herbivore interactions, have been studied by quantifying the total contents of the soluble phlorotannins with a variety of methods. Little attention has been given to either quantitative variation in cell-wall-bound and exuded phlorotannins or to qualitative variation in individual compounds. A quantification procedure was developed to measure the amount of cell-wall-bound phlorotannins. The quantification of soluble phlorotannins was adjusted for both large- and small-scale samples and used to estimate the amounts of exuded phlorotannins using bladder wrack (Fucus vesiculosus) as a model species. In addition, separation of individual soluble phlorotannins to produce a phlorotannin profile from the phenolic crude extract was achieved by high-performance liquid chromatography (HPLC). Along with these methodological studies, attention was focused on the factors in the procedure which generated variation in the yield of phlorotannins. The objective was to enhance the efficiency of the sample preparation procedure. To resolve the problem of rapid oxidation of phlorotannins in HPLC analyses, ascorbic acid was added to the extractant. The widely used colourimetric method was found to produce a variation in the yield that was dependent upon the pH and concentration of the sample. Using these developed, adjusted and modified methods, the phenotypic plasticity of phlorotannins was studied with respect to nutrient availability and herbivory. An increase in nutrients decreased the total amount of soluble phlorotannins but did not affect the cell-wall-bound phlorotannins, the exudation of phlorotannins or the phlorotannin profile achieved with HPLC. The presence of the snail Thedoxus fluviatilis on the thallus induced production of soluble phlorotannins, and grazing by the herbivorous isopod Idotea baltica increased the exudation of phlorotannins. To study whether the among-population variations in phlorotannin contents arise from the genetic divergence or from the plastic response of algae, or both, algae from separate populations were reared in a common garden. Genetic variation among local populations was found in both the phlorotannin profile and the content of total phlorotannins. Phlorotannins were also genetically variable within populations. This suggests that local algal populations have diverged in their contents of phlorotannins, and that they may respond to natural selection and evolve both quantitatively and qualitatively.

Selecting, testing and modifying a model for identifying potential key customers

Tämä työ tehtiin globaaliin elektroniikka-alan yritykseen. Diplomityö liittyy haasteeseen, jonka lisääntynyt globalisaatio ja kiristyvä kilpailu ovat luoneet: case yrityksen on selvitettävä kuinka se voi saavuttaa kasvutavoitteet myös tulevaisuudessa hankkimalla uusia asiakkaita ja olemalla yhä enenevissä määrin maailmanlaajuisesti läsnä. Tutkimuksen tavoite oli löytää sopiva malli potentiaalisten avainasiakkaiden identifiointiin ja valintaan, sekä testata ja modifioida valittua mallia case yrityksen tarpeiden mukaisesti. Erityisesti raakadatan kerääminen, asiakkaiden houkuttelevuuskriteerit ja kohdemarkkinarako olivat asioita, jotka tarvitsivat tutkimuksessa huomiota. Kirjallisuuskatsauksessa keskityttiin yritysmarkkinoihin, eri asiakassuhteenhallinnan lähestymistapoihin ja avainasiakkaiden määrittämiseen. CRM:n, KAM:n ja Customer Insight-ajattelun perusteet esiteltiin yhdessä eri avainasiakkaiden identifiointimallien kanssa. Valittua Chevertonin mallia testattiin ja muokattiin työn empiirisessä osassa. Tutkimuksen empiirinen kontribuutio on modifioitu malli potentiaalisten avainasiakkaiden identifiointiin. Se auttaa päätöksentekijöitä etenemään systemaattisesti ja organisoidusti askel askeleelta kohti potentiaalisten asiakkaiden listaa tietyltä markkina-alueelta. Työ tarjoaa työkalun tähän prosessiin sekä luo pohjaa tulevaisuuden tutkimukselle ja toimenpiteille.

Nutrient enrichment and water depth modify consumer control in rocky shore macroalgal communities

The objective of my thesis is to assess mechanisms of ecological community control in macroalgal communities in the Baltic Sea. In the top-down model, predatory fish feed on invertebrate mesograzers, releasing algae partly from grazing pressure. Such a reciprocal relationship is called trophic cascade. In the bottom-up model, nutrients increase biomass in the food chain. The nutrients are first assimilated by algae and, via food chain, increase also abundance of grazers and predators. Previous studies on oceanic shores have described these two regulative mechanisms in the grazer - alga link, but how they interact in the trophic cascades from fish to algae is still inadequately known. Because the top-down and bottom-up mechanisms are predicted to depend on environmental disturbances, such as wave stress and light, I have studied these models at two distinct water depths. There are five factorial field experiments behind the thesis, which were all conducted in the Finnish Archipelago Sea. In all the experiments, I studied macroalgal colonization - either density, filament length or biomass - on submerged colonization substrates. By excluding predatory fish and mesograzers from the algal communities, the studies compared the strength of the top-down control to natural algal communities. A part of the experimental units were, in addition, exposed to enriched nitrogen and phosphorus concentrations, which enabled testing of bottom-up control. These two models of community control were further investigated in shallow (<1 m) and deep (ca. 3 m) water. Moreover, the control mechanisms were also expected to depend on grazer species. Therefore different grazer species were enclosed into experimental units and their impacts on macroalgal communities were followed specifically. The community control in the Baltic rocky shores was found to follow theoretical predictions, which have not been confirmed by field studies before. Predatory fish limited grazing impact, which was seen as denser algal communities and longer algal filaments. Nutrient enrichment increased density and filament length of annual algae and, thus, changed the species composition of the algal community. The perennial alga Fucus vesiculosusA and the red alga Ceramium tenuicorne suffered from the increased nutrient availabilities. The enriched nutrient conditions led to denser grazer fauna, thereby causing strong top-down control over both the annual and perennial macroalgae. The strength of the top-down control seemed to depend on the density and diversity of grazers and predators as well as on the species composition of macroalgal assemblages. The nutrient enrichment led to, however, weaker limiting impact of predatory fish on grazer fauna, because fish stocks did not respond as quickly to enhanced resources in the environment as the invertebrate fauna. According to environmental stress model, environmental disturbances weaken the top-down control. For example, on a wave-exposed shore, wave stress causes more stress to animals close to the surface than deeper on the shore. Mesograzers were efficient consumers at both the depths, while predation by fish was weaker in shallow water. Thus, the results supported the environmental stress model, which predicts that environmental disturbance affects stronger the higher a species is in the food chain. This thesis assessed the mechanisms of community control in three-level food chains and did not take into account higher predators. Such predators in the Baltic Sea are, for example, cormorant, seals, white-tailed sea eagle, cod and salmon. All these predatory species were recently or are currently under intensive fishing, hunting and persecution, and their stocks have only recently increased in the region. Therefore, it is possible that future densities of top predators may yet alter the strengths of the controlling mechanisms in the Baltic littoral zone.

Non-Linear Journal Bearing Model for Analysis of Superharmonic Vibrations of Rotor Systems

A rotating machine usually consists of a rotor and bearings that supports it. The nonidealities in these components may excite vibration of the rotating system. The uncontrolled vibrations may lead to excessive wearing of the components of the rotating machine or reduce the process quality. Vibrations may be harmful even when amplitudes are seemingly low, as is usually the case in superharmonic vibration that takes place below the first critical speed of the rotating machine. Superharmonic vibration is excited when the rotational velocity of the machine is a fraction of the natural frequency of the system. In such a situation, a part of the machine’s rotational energy is transformed into vibration energy. The amount of vibration energy should be minimised in the design of rotating machines. The superharmonic vibration phenomena can be studied by analysing the coupled rotor-bearing system employing a multibody simulation approach. This research is focused on the modelling of hydrodynamic journal bearings and rotorbearing systems supported by journal bearings. In particular, the non-idealities affecting the rotor-bearing system and their effect on the superharmonic vibration of the rotating system are analysed. A comparison of computationally efficient journal bearing models is carried out in order to validate one model for further development. The selected bearing model is improved in order to take the waviness of the shaft journal into account. The improved model is implemented and analyzed in a multibody simulation code. A rotor-bearing system that consists of a flexible tube roll, two journal bearings and a supporting structure is analysed employing the multibody simulation technique. The modelled non-idealities are the shell thickness variation in the tube roll and the waviness of the shaft journal in the bearing assembly. Both modelled non-idealities may cause subharmonic resonance in the system. In multibody simulation, the coupled effect of the non-idealities can be captured in the analysis. Additionally one non-ideality is presented that does not excite the vibrations itself but affects the response of the rotorbearing system, namely the waviness of the bearing bushing which is the non-rotating part of the bearing system. The modelled system is verified with measurements performed on a test rig. In the measurements the waviness of bearing bushing was not measured and therefore it’s affect on the response was not verified. In conclusion, the selected modelling approach is an appropriate method when analysing the response of the rotor-bearing system. When comparing the simulated results to the measured ones, the overall agreement between the results is concluded to be good.

Non-resorbable glass fibre-reinforced composite with porous surface as bone substitute material: Experimental studies in vitro and in vivo focused on bone-implant interface

The development of load-bearing osseous implant with desired mechanical and surface properties in order to promote incorporation with bone and to eliminate risk of bone resorption and implant failure is a very challenging task. Bone formation and resoption processes depend on the mechanical environment. Certain stress/strain conditions are required to promote new bone growth and to prevent bone mass loss. Conventional metallic implants with high stiffness carry most of the load and the surrounding bone becomes virtually unloaded and inactive. Fibre-reinforced composites offer an interesting alternative to metallic implants, because their mechanical properties can be tailored to be equal to those of bone, by the careful selection of matrix polymer, type of fibres, fibre volume fraction, orientation and length. Successful load transfer at bone-implant interface requires proper fixation between the bone and implant. One promising method to promote fixation is to prepare implants with porous surface. Bone ingrowth into porous surface structure stabilises the system and improves clinical success of the implant. The experimental part of this work was focused on polymethyl methacrylate (PMMA) -based composites with dense load-bearing core and porous surface. Three-dimensionally randomly orientated chopped glass fibres were used to reinforce the composite. A method to fabricate those composites was developed by a solvent treatment technique and some characterisations concerning the functionality of the surface structure were made in vitro and in vivo. Scanning electron microscope observations revealed that the pore size and interconnective porous architecture of the surface layer of the fibre-reinforced composite (FRC) could be optimal for bone ingrowth. Microhardness measurements showed that the solvent treatment did not have an effect on the mechanical properties of the load-bearing core. A push-out test, using dental stone as a bone model material, revealed that short glass fibre-reinforced porous surface layer is strong enough to carry load. Unreacted monomers can cause the chemical necrosis of the tissue, but the levels of leachable resisidual monomers were considerably lower than those found in chemically cured fibre-reinforced dentures and in modified acrylic bone cements. Animal experiments proved that surface porous FRC implant can enhance fixation between bone and FRC. New bone ingrowth into the pores was detected and strong interlocking between bone and the implant was achieved.

Integration of existing military capability models into the Comprehensive Capability Meta-model

Abstract—This paper discusses existing military capability models and proposes a comprehensive capability meta-model (CCMM) which unites the existing capability models into an integrated and hierarchical whole. The Zachman Framework for Enterprise Architecture is used as a structure for the CCMM. The CCMM takes into account the abstraction level, the primary area of application, stakeholders, intrinsic process, and life cycle considerations of each existing capability model, and shows how the models relate to each other. The validity of the CCMM was verified through a survey of subject matter experts. The results suggest that the CCMM is of practical value to various capability stakeholders in many ways, such as helping to improve communication between the different capability communities.

The holistic military capability life cycle model

Abstract - This paper reviews existing military capability models and the capability life cycle. It proposes a holistic capability life-cycle model (HCLCM) that combines capability systems with related capability models. ISO 15288 standard is used as a framework to construct the HCLCM. The HCLCM also shows how capability models and systems relate to each other throughout the capability life cycle. The main contribution of this paper is conceptual in nature. The model complements the existing, but still evolving, understanding of the military capability life cycle in a holistic and systemic way. The model also increases understanding and facilitates communication among various military capability stakeholders.

The Role of Universities in the Triple Helix model of innovation management within the biotechnology industry, Case example: Turku Science Park Network

Biotechnology has been recognized as the key strategic technology for industrial growth. The industry is heavily dependent on basic research. Finland continues to rank in the top 10 of Europe's most innovative countries in terms of tax-policy, education system, infrastructure and the number of patents issued. Regardless of the excellent statistical results, the output of this innovativeness is below acceptable. Research on the issues hindering the output creation has already been done and the identifiable weaknesses in the Finland's National Innovation system are the non-existent growth of entrepreneurship and the missing internationalization. Finland is proven to have all the enablers of the innovation policy tools, but is lacking the incentives and rewards to push the enablers, such as knowledge and human capital, forward. Science Parks are the biggest operator in research institutes in the Finnish Science and Technology system. They exist with the purpose of speeding up the commercialization process of biotechnology innovations which usually include technological uncertainty, technical inexperience, business inexperience and high technology cost. Innovation management only internally is a rather historic approach, current trend drives towards open innovation model with strong triple helix linkages. The evident problems in the innovation management within the biotechnology industry are examined through a case study approach including analysis of the semi-structured interviews which included biotechnology and business expertise from Turku School of Economics. The results from the interviews supported the theoretical implications as well as conclusions derived from the pilot survey, which focused on the companies inside Turku Science Park network. One major issue that the Finland's National innovation system is struggling with is the fact that it is technology driven, not business pulled. Another problem is the university evaluation scale which focuses more on number of graduates and short-term factors, when it should put more emphasis on the cooperation success in the long-term, such as the triple helix connections with interaction and knowledge distribution. The results of this thesis indicated that there is indeed requirement for some structural changes in the Finland's National innovation system and innovation policy in order to generate successful biotechnology companies and innovation output. There is lack of joint output and scales of success, lack of people with experience, lack of language skills, lack of business knowledge and lack of growth companies.

Long-term nutrient load management and lake restoration: Case of Säkylän Pyhäjärvi (SW Finland)

Eutrophication caused by anthropogenic nutrient pollution has become one of the most severe threats to water bodies. Nutrients enter water bodies from atmospheric precipitation, industrial and domestic wastewaters and surface runoff from agricultural and forest areas. As point pollution has been significantly reduced in developed countries in recent decades, agricultural non-point sources have been increasingly identified as the largest source of nutrient loading in water bodies. In this study, Lake Säkylän Pyhäjärvi and its catchment are studied as an example of a long-term, voluntary-based, co-operative model of lake and catchment management. Lake Pyhäjärvi is located in the centre of an intensive agricultural area in southwestern Finland. More than 20 professional fishermen operate in the lake area, and the lake is used as a drinking water source and for various recreational activities. Lake Pyhäjärvi is a good example of a large and shallow lake that suffers from eutrophication and is subject to measures to improve this undesired state under changing conditions. Climate change is one of the most important challenges faced by Lake Pyhäjärvi and other water bodies. The results show that climatic variation affects the amounts of runoff and nutrient loading and their timing during the year. The findings from the study area concerning warm winters and their influences on nutrient loading are in accordance with the IPCC scenarios of future climate change. In addition to nutrient reduction measures, the restoration of food chains (biomanipulation) is a key method in water quality management. The food-web structure in Lake Pyhäjärvi has, however, become disturbed due to mild winters, short ice cover and low fish catch. Ice cover that enables winter seining is extremely important to the water quality and ecosystem of Lake Pyhäjärvi, as the vendace stock is one of the key factors affecting the food web and the state of the lake. New methods for the reduction of nutrient loading and the treatment of runoff waters from agriculture, such as sand filters, were tested in field conditions. The results confirm that the filter technique is an applicable method for nutrient reduction, but further development is needed. The ability of sand filters to absorb nutrients can be improved with nutrient binding compounds, such as lime. Long-term hydrological, chemical and biological research and monitoring data on Lake Pyhäjärvi and its catchment provide a basis for water protection measures and improve our understanding of the complicated physical, chemical and biological interactions between the terrestrial and aquatic realms. In addition to measurements carried out in field conditions, Lake Pyhäjärvi and its catchment were studied using various modelling methods. In the calibration and validation of models, long-term and wide-ranging time series data proved to be valuable. Collaboration between researchers, modellers and local water managers further improves the reliability and usefulness of models. Lake Pyhäjärvi and its catchment can also be regarded as a good research laboratory from the point of view of the Baltic Sea. The main problem in both of them is eutrophication caused by excess nutrients, and nutrient loading has to be reduced – especially from agriculture. Mitigation measures are also similar in both cases.

Post-transaction brand and model line-up integration in the automotive industry: Case studies of European companies as target of acquisitions by Chinese and Indian multinational corporations

Corporations practice company acquisitions in order to create shareholder’s value. During the last few decades, the companies in emerging markets have become active in the acquisition business. During the last decade, large and significant acquisitions have occurred especially in automotive industry. While domestic markets have become too competitive and companies are lacking required capabilities, they seek possibilities to expand into Western markets by attaining valuable assets through acquisitions of developed country corporations. This study discusses the issues and characteristics of these acquisitions through case studies. The purpose of this study was to identify the acquisition motives and strategies for post-transaction brand and product integration as well as analyze the effect of the motives to the integration strategy. The cases chosen for the research were Chinese Geely acquiring Swedish Volvo in 2010 and Indian Tata Motors buying British Jaguar Land Rover in 2008. The main topics were chosen according to their significance for companies in automotive industry as well as those are most visible parts for consumers. The study is based on qualitative case study methods, analyzing secondary data from academic papers and news articles as well as companies’ own announcements e.g. stock exchange and press releases. The study finds that the companies in the cases mainly possessed asset-seeking and market-seeking motives. In addition, the findings refer to rather minimal post-acquisition brand and product integration strategies. Mainly the parent companies left the target company autonomous to make their own business strategies and decisions. The most noticeable integrations were in the product development and production processes. Through restructuring the product architectures, the companies were able to share components and technology between product families and brands, which results in cutting down costs and in increase of profitability and efficiency. In the Geely- Volvo case, the strategy focused more on component sharing and product development know-how, whereas in Tata Motors-Jaguar Land Rover case, the main actions were to cut down costs through component sharing and combine production and distribution networks especially in Asian markets. However, it was evident that in both cases the integration and technology sharing were executed cautiously to prevent on harming the valuable image of the luxury brand. This study has concluded that the asset-seeking motives have significant influence on the posttransaction brand and model line-up integration strategies. By taking a cautious approach in acquiring assets, such as luxury brand, the companies in the cases have implemented a successful post-acquisition strategy and managed to create value for the shareholders at least in short-term. Yritykset harjoittavat yritysostoja luodakseen osakkeenomistajille lisäarvoa. Viimeisten muutamien vuosikymmenien aikana yritykset kehittyvissä maissa ovat myös aktivoituneet yritysostoissa. Viimeisen vuosikymmenen aikana erityisesti autoteollisuudessa on esiintynyt suuria ja merkittäviä yritysostoja. Koska kilpailu kotimaan markkinoilla on kiristynyt ja yritykset ovat vailla vaadittavia valmiuksia, ne etsivät mahdollisuuksiaan laajentaa länsimaisiin markkinoihin hankkimalla arvokkaita etuja kehittyneiden maiden yrityksistä yritysostojen avulla. Tämä tutkimus pohtii näiden yritysostojen olennaisia kysymyksiä ja ominaisuuksia casetutkimuksien kautta. Tutkimuksen tarkoitus oli tunnistaa sekä yritysostojen motiiveja ja brändi- ja mallisto-integraation strategioita että analysoida kyseisten motiivien vaikutusta integraatiostrategiaan. Tapaus-tutkimuksiksi valittiin kiinalaisen Geelyn yritysosto ruotsalaisesta Volvosta vuonna 2010 ja intialaisen Tata Motorsin yritysosto englantilaisesta Jaguar Land Roverista vuonna 2008. Tutkimus on kvalitatiivinen case-tutkimus ja siinä analysoidaan toissijaista tietoa sekä akateemisten ja uutisartikkeleiden että yritysten omien ilmoitusten, kuten pörssi- ja lehdistötiedotteiden, kautta. Tutkimuksen tulokset osoittavat, että tutkittujen yritysten toiminnat perustuivat motiiveihin, joita ajoivat etujen and uusien markkinoiden tarve. Sen lisäksi tutkimustulokset osoittivat, että yritysoston jälkeinen brändi- ja mallisto-integraatio pidettiin minimaalisena. Pääasiallisesti kohdeyrityksille jätettiin autonomia tehdä omat liikkeenjohdolliset päätökset yritysstrategioihin liittyen. Huomattavimmat integraatiot koskivat tuotekehityksellisiä ja tuotannollisia prosesseja. Kehittämällä uudelleen tuotearkkitehtuureja, yritykset pystyivät jakamaan komponentteja ja teknologiaa tuoteperheiden ja brändien välillä. Tämä mahdollisti kustannusleikkauksia sekä kannattavuuden ja tehokkuuden parantamista. Geely-Volvo –tapauksessa integraatiostrategia keskittyi komponenttien jakamiseen yhteisten tuotearkkitehtuurien avulla ja tuotekehityksen ammattitaitoon, kun taas Tata Motors-JLR –tapauksessa päätoiminnat olivat kustannuksien leikkaus sekä tuotannon ja jakeluverkoston yhdistäminen erityisesti Aasian maissa. Yhteistä yrityskaupoissa oli, että brändi- ja mallisto-integraatio sekä teknologian jakaminen suoritettiin varoen ehkäistäkseen arvokkaiden luksus-brändien tuotekuvan vahingoittamista. Tutkimuksen lopputulokset osoittavat, että yrityskaupan motiiveilla on huomattava vaikutus brändija mallisto-integraation strategiaan. Toteuttamalla varovaista lähestymistapaa luksus-brändin hankinnassa ja integraatiossa, yritykset ovat onnistuneet luomaan lisäarvoa osakkeenomistajille vähintään lyhyellä aikavälillä.

Item-level life-cycle model for maintenance network – from cost to additional value

The importance of industrial maintenance has been emphasized during the last decades; it is no longer a mere cost item, but one of the mainstays of business. Market conditions have worsened lately, investments in production assets have decreased, and at the same time competition has changed from taking place between companies to competition between networks. Companies have focused on their core functions and outsourced support services, like maintenance, above all to decrease costs. This new phenomenon has led to increasing formation of business networks. As a result, a growing need for new kinds of tools for managing these networks effectively has arisen. Maintenance costs are usually a notable part of the life-cycle costs of an item, and it is important to be able to plan the future maintenance operations for the strategic period of the company or for the whole life-cycle period of the item. This thesis introduces an itemlevel life-cycle model (LCM) for industrial maintenance networks. The term item is used as a common definition for a part, a component, a piece of equipment etc. The constructed LCM is a working tool for a maintenance network (consisting of customer companies that buy maintenance services and various supplier companies). Each network member is able to input their own cost and profit data related to the maintenance services of one item. As a result, the model calculates the net present values of maintenance costs and profits and presents them from the points of view of all the network members. The thesis indicates that previous LCMs for calculating maintenance costs have often been very case-specific, suitable only for the item in question, and they have also been constructed for the needs of a single company, without the network perspective. The developed LCM is a proper tool for the decision making of maintenance services in the network environment; it enables analysing the past and making scenarios for the future, and offers choices between alternative maintenance operations. The LCM is also suitable for small companies in building active networks to offer outsourcing services for large companies. The research introduces also a five-step constructing process for designing a life-cycle costing model in the network environment. This five-step designing process defines model components and structure throughout the iteration and exploitation of user feedback. The same method can be followed to develop other models. The thesis contributes to the literature of value and value elements of maintenance services. It examines the value of maintenance services from the perspective of different maintenance network members and presents established value element lists for the customer and the service provider. These value element lists enable making value visible in the maintenance operations of a networked business. The LCM added with value thinking promotes the notion of maintenance from a “cost maker” towards a “value creator”.