Supplier process development

Tämän diplomityön tarkoituksena on parantaa Timberjackin ja Timberjackin toimittajien välistä yhteistyötä ja saattaa Timberjackin toimintatavat toimittajien tietoisuuteen. Aiheen laajuuden vuoksi yksittäisten aihepiirien syvällinen tutkiminen jäi vähäiseksi. Monet globaalit yhtiöt ovat nykyisin ottaneet selkeäksi strategiakseen toimintojensa ulkoistamisen ja tällöin yhtiölle itselleen jää ainoastaan lopputuotteiden kokoonpanon työvaiheet. Tämä tarkoittaa, että ulkoisilta toimittajilta ostetaan entistä enemmän komponentteja ja tuotekokonaisuuksia. Toisaalta taas harvalla toimittajalla on vielä tarvittavaa tieto-taitoa tai resursseja vastata päämiehen lisääntyviin tarpeisiin. Tämä on syy miksi suuret maailmanluokan yhtiöt panostavat nykyisin huomattavia voimavaroja toimittajaketjun kehittämiseen. Diplomityön ensimmäisessä osiossa paneudutaan teoria-asioihin, jotka tulee olla tiedossa kehitettäessä yhteistyötä toimittajien kanssa. Toisessa osassa tutkitaan Timberjackin toimintatapoja, tuotantomallia ja nykyisiä toimittajia. Nämä tiedot ovat välttämättömiä, kun luodaan kokonaiskuvaa toimittajaprosessista ja kun kehitetään uusia työkaluja helpottamaan toimittajien ja Timberjackin välistä yhteistyötä. Työn tuloksena Timberjackilla on nyt toimittajakäsikirja, joka sisältää tietoja, jotka toimittajien tulee huomioida toimiessaan Timberjackin kanssa ja myös ohjeita siitä, kuinka toimittajat voivat kehittää omia prosessejaan.

Power quality improving with virtual flux-based voltage source line converter

Line converters have become an attractive AC/DC power conversion solution in industrial applications. Line converters are based on controllable semiconductor switches, typically insulated gate bipolar transistors. Compared to the traditional diode bridge-based power converters line converters have many advantageous characteristics, including bidirectional power flow, controllable de-link voltage and power factor and sinusoidal line current. This thesis considers the control of the lineconverter and its application to power quality improving. The line converter control system studied is based on the virtual flux linkage orientation and the direct torque control (DTC) principle. A new DTC-based current control scheme is introduced and analyzed. The overmodulation characteristics of the DTC converter are considered and an analytical equation for the maximum modulation index is derived. The integration of the active filtering features to the line converter isconsidered. Three different active filtering methods are implemented. A frequency-domain method, which is based on selective harmonic sequence elimination, anda time-domain method, which is effective in a wider frequency band, are used inharmonic current compensation. Also, a voltage feedback active filtering method, which mitigates harmonic sequences of the grid voltage, is implemented. The frequency-domain and the voltage feedback active filtering control systems are analyzed and controllers are designed. The designs are verified with practical measurements. The performance and the characteristics of the implemented active filtering methods are compared and the effect of the L- and the LCL-type line filteris discussed. The importance of the correct grid impedance estimate in the voltage feedback active filter control system is discussed and a new measurement-based method to obtain it is proposed. Also, a power conditioning system (PCS) application of the line converter is considered. A new method for correcting the voltage unbalance of the PCS-fed island network is proposed and experimentally validated.

Uuteaineiden on-line-mittaus koivusulfaattisellutehtaalla

Tämän työn tarkoituksena oli tutkia pihkanhallintaa sulfaattisellutehtaalla ja uuteaineiden analysointimenetelmiä massasta ja suodoksesta. Tavoitteena oli kehittää uuteaineiden on-line mittausmenetelmä sulfaattisellutehtaalle. Kirjallisuusosassa esitettiin sulfaattisellun valmistusprosessi ja uuteaineiden käyttäytyminen prosessissa. Lisäksi työssä käsiteltiin tärkeimpiä pihkanhallintamenetelmiä ja uuteaineiden analysointia. Kokeellisessa osassa määritettiin uuteainepitoisuudet 29:stä massa- ja pesusuodosnäytteestä. Lisäksi suodosnäytteiden sameus ja kemiallinen hapenkulutus määritettiin laboratoriossa. On-line mittaukset tehtiin DD-pesurin paluusuodoksesta, josta mitattiin johtokyky, lämpötila, taitekerroin ja pH. Sameutta yritettiin mitata on-line nefelometrillä, mutta käytössä ollut laite ei soveltunut tumman suodoksen mittaamiseen. Työssä saatujen tulosten perusteella voidaan todeta, että pesusuodoksen ominaisuuksia mittaamalla ei voida arvioida massan uutepitoisuutta luotettavasti. Suodoksen ja massan uutepitoisuuksien välinen selitysaste oli 54%. Saippuoitumattomien uuteaineiden pitoisuuden ollessa erityisen suuri, suodoksen uutepitoisuus ei korreloi massassa olevan uutteen määrän kanssa. Täten kyseinen mittausmenetelmä ei ole sopiva, sillä se ei toimi silloin, kun olisi tärkeintä tietää oikea uuteainepitoisuus pihkanhallintakemikaalien annosten määrittämiseksi. Suodoksen sameus riippui sen uutepitoisuudesta 80% selitysasteella. Sameusmittaus on nopea ja suhteellisen luotettava menetelmä suodosten uutepitoisuuksien arviointiin, mutta se vaatii mittalaitteen joka käyttää usean ilmaisimen tekniikkaa. On-line-mittauksissa laitteisto tulisi varustaa automaattisella pesulaitteella, sillä mittarin linssit likaantuvat helposti prosessivirrassa.

Determining, Balancing and Controlling of Pitch and White Pitch at Stora Enso Kabel Production Line 4

Työn ensimmäisenä tarkoituksena oli kartoittaa kiinteä-neste ja neste-neste uuttomenetelmillä pihkan ja valkopihkan määrä Stora Enso Kabelin tuotantolinja 4:llä. Työn kannalta oli myöstärkeää saada selvyys saostumien koostumuksesta. Lopullinen päämäärä oli automatisoida fiksatiivin annostelu uuden, jatkuvatoimisen märänpäänanalysaattorin avulla. Mäntyosuuden kasvattaminen hiokemassassa lisää hydrofobisten partikkeleiden lukumäärää, minkä uskotaan lisäävän saostumariskiä. Työtä varten kehitetty neste-neste uuttomenetelmä, jota ei ole liiemmin paperiteollisuudessa käytetty, voi olla hyvä menetelmä lipofiilisten komponenttien määrän arviointiin tietyssä määrässä massa- tai prosessivesinäytettä. Virtaussytometri-menetelmän avulla tutkittiin pihka- tai valkopihkapartikkeleiden määrää ja kokojakaumaa eri prosessinäytteissä. Virtaussytometri-menetelmällä mitattujen valkopihkapartikkeleiden lukumäärän ja päällystetyn hylyn saostimen suodoksen sameuden välille löytyiselvä korrelaatio. Fiksatiivimäärän vaikutusta päällystetyn hylyn saostimen suodoksen sameuteen tutkittiin koeajojaksolla, jossa fiksatiivin annostelua säädettiin käsin. Käytetyt annosmäärät eivät riittäneet sameuden pitämiseen tasaisena matalalla tasolla.

Computational Analysis and Optimization of Real Gas Flow In Small Centrifugal Compressors

Small centrifugal compressors are more and more widely used in many industrialsystems because of their higher efficiency and better off-design performance comparing to piston and scroll compressors as while as higher work coefficient perstage than in axial compressors. Higher efficiency is always the aim of the designer of compressors. In the present work, the influence of four partsof a small centrifugal compressor that compresses heavy molecular weight real gas has been investigated in order to achieve higher efficiency. Two parts concern the impeller: tip clearance and the circumferential position of the splitter blade. The other two parts concern the diffuser: the pinch shape and vane shape. Computational fluid dynamics is applied in this study. The Reynolds averaged Navier-Stokes flow solver Finflo is used. The quasi-steady approach is utilized. Chien's k-e turbulence model is used to model the turbulence. A new practical real gas model is presented in this study. The real gas model is easily generated, accuracy controllable and fairly fast. The numerical results and measurements show good agreement. The influence of tip clearance on the performance of a small compressor is obvious. The pressure ratio and efficiency are decreased as the size of tip clearance is increased, while the total enthalpy rise keeps almost constant. The decrement of the pressure ratio and efficiency is larger at higher mass flow rates and smaller at lower mass flow rates. The flow angles at the inlet and outlet of the impeller are increased as the size of tip clearance is increased. The results of the detailed flow field show that leakingflow is the main reason for the performance drop. The secondary flow region becomes larger as the size of tip clearance is increased and the area of the main flow is compressed. The flow uniformity is then decreased. A detailed study shows that the leaking flow rate is higher near the exit of the impeller than that near the inlet of the impeller. Based on this phenomenon, a new partiallyshrouded impeller is used. The impeller is shrouded near the exit of the impeller. The results show that the flow field near the exit of the impeller is greatly changed by the partially shrouded impeller, and better performance is achievedthan with the unshrouded impeller. The loading distribution on the impeller blade and the flow fields in the impeller is changed by moving the splitter of the impeller in circumferential direction. Moving the splitter slightly to the suction side of the long blade can improve the performance of the compressor. The total enthalpy rise is reduced if only the leading edge of the splitter ismoved to the suction side of the long blade. The performance of the compressor is decreased if the blade is bended from the radius direction at the leading edge of the splitter. The total pressure rise and the enthalpy rise of thecompressor are increased if pinch is used at the diffuser inlet. Among the fivedifferent pinch shape configurations, at design and lower mass flow rates the efficiency of a straight line pinch is the highest, while at higher mass flow rate, the efficiency of a concave pinch is the highest. The sharp corner of the pinch is the main reason for the decrease of efficiency and should be avoided. The variation of the flow angles entering the diffuser in spanwise direction is decreased if pinch is applied. A three-dimensional low solidity twisted vaned diffuser is designed to match the flow angles entering the diffuser. The numerical results show that the pressure recovery in the twisted diffuser is higher than in a conventional low solidity vaned diffuser, which also leads to higher efficiency of the twisted diffuser. Investigation of the detailed flow fields shows that the separation at lower mass flow rate in the twisted diffuser is later than in the conventional low solidity vaned diffuser, which leads to a possible wider flow range of the twisted diffuser.

Pain-evoked alterations on gingival blood flow and gingival crevicular fluid (GCF) neuropeptide SP and collagenase-2 (MMP-8) levels

Previous studies have demonstrated that clinical pulpal pain can induce the expression of pro-inflammatory neuropeptides in the adjacent gingival crevice fluid (GCF). Vasoactive agents such as substance P (SP) are known to contribute to the inflammatory type of pain and are associated with increased blood flow. More recent animal studies have shown that application of capsaicin on alveolar mucosa provokes pain and neurogenic vasodilatation in the adjacent gingiva. Pain-associated inflammatory reactions may initiate expression of several pro- and anti-inflammatory mediators. Collagenase-2 (MMP-8) has been considered to be the major destructive protease, especially in the periodontitis-affected gingival crevice fluid (GCF). MMP-8 originates mostly from neutrophil leukocytes, the first line of defence cells that exist abundantly in GCF, especially in inflammation. With this background, we wished to clarify the spatial extensions and differences between tooth-pain stimulation and capsaicin-induced neurogenic vasodilatation in human gingiva. Experiments were carried out to study whether tooth stimulation and capsaicin stimulation of alveolar mucosa would induce changes in GCF MMP-8 levels and whether tooth stimulation would release neuropeptide SP in GCF. The experiments were carried out on healthy human volunteers. During the experiments, moderate and high intensity painful tooth stimulation was performed by a constant current tooth stimulator. Moderate tooth stimulation activates A-delta fibres, while high stimulation also activates C-fibres. Painful stimulation of the gingiva was achieved by topical application of capsaicin-moistened filter paper on the mucosal surface. Capsaicin is known to activate selectively nociceptive C-fibres of stimulated tissue. Pain-evoked vasoactive changes in gingivomucosal tissues were mapped by laser Doppler imaging (LDI), which is a sophisticated and non-invasive method for studying e.g. spatial and temporal characteristics of pain- and inflammation-evoked blood flow changes in gingivomucosal tissues. Pain-evoked release of MMP-8 in GCF samples was studied by immunofluorometric assay (IFMA) and Western immunoblotting. The SP levels in GCF were analysed by Enzyme immunoassay (EIA). During the experiments, subjective stimulus-evoked pain responses were determined by a visual analogue pain scale. Unilateral stimulation of alveolar mucosa and attached gingiva by capsaicin evoked a distinct neurogenic vasodilatation in the ipsilateral gingiva, which attenuated rapidly at the midline. Capsaicin stimulation of alveolar mucosa provoked clear inflammatory reactions. In contrast to capsaicin stimuli, tooth stimulation produced symmetrical vasodilatations bilaterally in the gingiva. The ipsilateral responses were significantly smaller during tooth stimulation than during capsaicin stimuli. The current finding – that tooth stimulation evokes bilateral vasodilatation while capsaicin stimulation of the gingiva mainly produces unilateral vasodilatation – emphasises the usefulness of LDI in clarifying spatial features of neurogenic vasoactive changes in the intra-oral tissues. Capsaicin stimulation of the alveolar mucosa induced significant elevations in MMP-8 levels and activation in GCF of the adjacent teeth. During the experiments, no marked changes occurred in MMP-8 levels in the GCF of distantly located teeth. Painful stimulation of the upper incisor provoked elevations in GCF MMP-8 and SP levels of the stimulated tooth. The GCF MMP-8 and SP levels of the non-stimulated teeth were not changed. These results suggest that capsaicin-induced inflammatory reactions in gingivomucosal tissues do not cross the midline in the anterior maxilla. The enhanced reaction found during stimulation of alveolar mucosa indicates that alveolar mucosa is more sensitive to chemical irritants than the attached gingiva. Analysis of these data suggests that capsaicin-evoked neurogenic inflammation in the gingiva can trigger the expression and activation of MMP-8 in GCF of the adjacent teeth. In this study, it is concluded that experimental tooth pain at C-fibre intensity can induce local elevations in MMP-8 and SP levels in GCF. Depending on the role of MMP-8 in inflammation, in addition to surrogated tissue destruction, the elevated MMP-8 in GCF may also reflect accelerated local defensive and anti-inflammatory reactions.

The intrinsic mechanisms of softwood fiber damage in brown stock fiber line unit operations Lappeenranta 2010

The effects of pulp processing on softwood fiber properties strongly influence the properties of wet and dry paper webs. Pulp strength delivery studies have provided observations that much of the strength potential of long fibered pulp is lost during brown stock fiber line operations where the pulp is merely washed and transferred to the subsequent processing stages. The objective of this work was to study the intrinsic mechanisms which maycause fiber damage in the different unit operations of modern softwood brown stock processing. The work was conducted by studying the effects of industrial machinery on pulp properties with some actions of unit operations simulated in laboratory scale devices under controlled conditions. An optical imaging system was created and used to study the orientation of fibers in the internal flows during pulp fluidization in mixers and the passage of fibers through the screen openings during screening. The qualitative changes in fibers were evaluated with existing and standardized techniques. The results showed that each process stage has its characteristic effects on fiber properties: Pulp washing and mat formation in displacement washers introduced fiber deformations especially if the fibers entering the stage were intact, but it did not decrease the pulp strength properties. However, storage chests and pulp transfer after displacement washers contributed to strength deterioration. Pulp screening proved to be quite gentle, having the potential of slightly evening out fiber deformations from very deformed pulps and vice versa inflicting a marginal increase in the deformation indices if the fibers were previously intact. Pulp mixing in fluidizing industrial mixers did not have detrimental effects on pulp strength and had the potential of slightly evening out the deformations, provided that the intensity of fluidization was high enough to allow fiber orientation with the flow and that the time of mixing was short. The chemical and mechanical actions of oxygen delignification had two distinct effects on pulp properties: chemical treatment clearly reduced pulp strength with and without mechanical treatment, and the mechanical actions of process machinery introduced more conformability to pulp fibers, but did not clearly contribute to a further decrease in pulp strength. The chemical composition of fibers entering the oxygen stage was also found to affect the susceptibility of fibers to damage during oxygen delignification. Fibers with the smallest content of xylan were found to be more prone to irreversibledeformations accompanied with a lower tensile strength of the pulp. Fibers poor in glucomannan exhibited a lower fiber strength while wet after oxygen delignification as compared to the reference pulp. Pulps with the smallest lignin content on the other hand exhibited improved strength properties as compared to the references.

Characterization of the filter media used in the dual media filter

The removal of organics from copper electrolyte solutions after solvent extraction by dual media filtration is one of the most efficient ways to ensure the clean electrolyte flow into the electrowinning. The clean electrolyte will ensure the good quality cathode plate production. Dual media filtration uses two layers of filter media for filtration as anthracite and garnet respectively. The anthracite layer will help the coalescing of the entrained organic droplets which will then float to the top of the filter, and back to the solvent extraction process. The garnet layer will catch any solids left in the electrolyte traveling through the filter media. This thesis will concentrate on characterization of five different anthracites in order to find some differences using specific surface area analysis, particle size analysis, and morphology analysis. These results are compared to the pressure loss values obtained from lab column tests and bed expansion behavior. The goal of the thesis was to find out if there were any differences in the anthracite which would make the one perform better than the other. There were no big differences found on any aspect of the particle characterization, but some found differences should be further studied in order to confirm the meaning of the porosity, surface area, intensity mean and intensity SD (Standard Deviation) on anthracites and their use in dual media filtration. The thesis work analyzed anthracite samples the way that is not found on any public literature sources, and further studies on the issue would bring more knowledge to the electrolyte process.