Phase voltage control and filtering in a converter-fed single-phase customer-end system of the LVDC distribution network

In recent years, the network vulnerability to natural hazards has been noticed. Moreover, operating on the limits of the network transmission capabilities have resulted in major outages during the past decade. One of the reasons for operating on these limits is that the network has become outdated. Therefore, new technical solutions are studied that could provide more reliable and more energy efficient power distributionand also a better profitability for the network owner. It is the development and price of power electronics that have made the DC distribution an attractive alternative again. In this doctoral thesis, one type of a low-voltage DC distribution system is investigated. Morespecifically, it is studied which current technological solutions, used at the customer-end, could provide better power quality for the customer when compared with the current system. To study the effect of a DC network on the customer-end power quality, a bipolar DC network model is derived. The model can also be used to identify the supply parameters when the V/kW ratio is approximately known. Although the model provides knowledge of the average behavior, it is shown that the instantaneous DC voltage ripple should be limited. The guidelines to choose an appropriate capacitance value for the capacitor located at the input DC terminals of the customer-end are given. Also the structure of the customer-end is considered. A comparison between the most common solutions is made based on their cost, energy efficiency, and reliability. In the comparison, special attention is paid to the passive filtering solutions since the filter is considered a crucial element when the lifetime expenses are determined. It is found out that the filter topology most commonly used today, namely the LC filter, does not provide economical advantage over the hybrid filter structure. Finally, some of the typical control system solutions are introduced and their shortcomings are presented. As a solution to the customer-end voltage regulation problem, an observer-based control scheme is proposed. It is shown how different control system structures affect the performance. The performance meeting the requirements is achieved by using only one output measurement, when operating in a rigid network. Similar performance can be achieved in a weak grid by DC voltage measurement. An additional improvement can be achieved when an adaptive gain scheduling-based control is introduced. As a conclusion, the final power quality is determined by a sum of various factors, and the thesis provides the guidelines for designing the system that improves the power quality experienced by the customer.

The electricity distribution network in Saint-Petersburg area and benchmark between Saint-Petersburg and City of Stockholm related distribution companies' performance

The main objective of the Thesis is the description of the electricity distribution networks in Saint-Petersburg area and Stockholm as well. Main similarity and differences in the construction and technicalperformance are presented in the study. Present and future development and investment into the electricity distribution network of OJSC Lenenergo are viewed. The Thesis presents the overview of the power industry reform in Russia. The current state of the electricity distribution sector is described. The study views the participation of the foreign investor "Fortum Power and Heat Oy" inthe development and management of the OJSC Lenenergo. Benchmark comparison of the prices and tangible assets of the main electricity distribution companies in Saint-Petersburg and Stockholm areas is done.

Logistics in Pump Manufacturer's Spare Part Distribution Network

Tässä diplomityössä käsitellään pumppujen maailmanlaajuista varaosa-jakelua. Työn pääpaino on varaosien moniportaisen jakeluverkon toimitusketjun logistiikassa. Asiakaspalvelussa varaosien nopea saatavuus on ratkaisevassa asemassa, jotta asiakkaiden tehtaiden käynnissäpito voidaan turvata. Työn tavoitteena oli kehittää Ahlström Pumpuille uusi globaali toimintamalli varaosien jakeluun. Tämä uusi varaosien jakelumalli on kehitetty pääasiassa sopimusasiakkaille, jotka ovat halukkaita ulkoistamaan varaosatoimintonsa. Mallia sovelletaan käytäntöön varaosien jakelussa ensiksi Suomessa ja Ruotsissa. Myöhemmin on tarkoitus kopioida mallia myös muualle. Malli on pyritty rakentamaan siten, että siihen voidaan helposti liittää muita Ahlström Pumppujen tarjoamia palveluita. Työssä koottu materiaali perustuu pääasiassa haastatteluihin, palavereihin, erilaisiin sisäisiin raportteihin, kirjallisuuteen ja itsenäiseen selvitystyöhön. Työssä on myös tutustuttu kolmen eri yrityksen after-sales- ja varaosatoimintaan.

Analysis of electricity distribution network operation business models and capitalization of control room functions with DMS

Electricity distribution network operation (NO) models are challenged as they are expected to continue to undergo changes during the coming decades in the fairly developed and regulated Nordic electricity market. Network asset managers are to adapt to competitive technoeconomical business models regarding the operation of increasingly intelligent distribution networks. Factors driving the changes for new business models within network operation include: increased investments in distributed automation (DA), regulative frameworks for annual profit limits and quality through outage cost, increasing end-customer demands, climatic changes and increasing use of data system tools, such as Distribution Management System (DMS). The doctoral thesis addresses the questions a) whether there exist conditions and qualifications for competitive markets within electricity distribution network operation and b) if so, identification of limitations and required business mechanisms. This doctoral thesis aims to provide an analytical business framework, primarily for electric utilities, for evaluation and development purposes of dedicated network operation models to meet future market dynamics within network operation. In the thesis, the generic build-up of a business model has been addressed through the use of the strategicbusiness hierarchy levels of mission, vision and strategy for definition of the strategic direction of the business followed by the planning, management and process execution levels of enterprisestrategy execution. Research questions within electricity distribution network operation are addressed at the specified hierarchy levels. The results of the research represent interdisciplinary findings in the areas of electrical engineering and production economics. The main scientific contributions include further development of the extended transaction cost economics (TCE) for government decisions within electricity networks and validation of the usability of the methodology for the electricity distribution industry. Moreover, DMS benefit evaluations in the thesis based on the outage cost calculations propose theoretical maximum benefits of DMS applications equalling roughly 25% of the annual outage costs and 10% of the respective operative costs in the case electric utility. Hence, the annual measurable theoretical benefits from the use of DMS applications are considerable. The theoretical results in the thesis are generally validated by surveys and questionnaires.

Power-line-communication-based data transmission concept for an LVDC electricity distribution network – Analysis and implementation

Communications play a key role in modern smart grids. New functionalities that make the grids ‘smart’ require the communication network to function properly. Data transmission between intelligent electric devices (IEDs) in the rectifier and the customer-end inverters (CEIs) used for power conversion is also required in the smart grid concept of the low-voltage direct current (LVDC) distribution network. Smart grid applications, such as smart metering, demand side management (DSM), and grid protection applied with communications are all installed in the LVDC system. Thus, besides remote connection to the databases of the grid operators, a local communication network in the LVDC network is needed. One solution applied to implement the communication medium in power distribution grids is power line communication (PLC). There are power cables in the distribution grids, and hence, they may be applied as a communication channel for the distribution-level data. This doctoral thesis proposes an IP-based high-frequency (HF) band PLC data transmission concept for the LVDC network. A general method to implement the Ethernet-based PLC concept between the public distribution rectifier and the customerend inverters in the LVDC grid is introduced. Low-voltage cables are studied as the communication channel in the frequency band of 100 kHz–30 MHz. The communication channel characteristics and the noise in the channel are described. All individual components in the channel are presented in detail, and a channel model, comprising models for each channel component is developed and verified by measurements. The channel noise is also studied by measurements. Theoretical signalto- noise ratio (SNR) and channel capacity analyses and practical data transmission tests are carried out to evaluate the applicability of the PLC concept against the requirements set by the smart grid applications in the LVDC system. The main results concerning the applicability of the PLC concept and its limitations are presented, and suggestion for future research proposed.

Distribution network design and optimization

The objective of this thesis is to examine distribution network designs and modeling practices and create a framework to identify best possible distribution network structure for the case company. The main research question therefore is: How to optimize case company’s distribution network in terms of customer needs and costs? Theory chapters introduce the basic building blocks of the distribution network design and needed calculation methods and models. Framework for the distribution network projects was created based on the theory and the case study was carried out by following the defined framework. Distribution network calculations were based on the company’s sales plan for the years 2014 - 2020. Main conclusions and recommendations were that the new Asian business strategy requires high investments in logistics and the first step is to open new satellite DC in China as soon as possible to support sales and second possible step is to open regional DC in Asia within 2 - 4 years.

Managing regulatory risks when outsourcing network-related services in the electricity distribution sector

Deregulation of the electricity sector liberated the electricity sale and production for competitive forces while in the network business, electricity transmission and distribution, natural monopoly positions were recognised. Deregulation was accompanied by efficiencyoriented thinking on the whole electricity supply industry. For electricity distribution this meant a transition from a public service towards profit-driven business guided by economic regulation. Regulation is the primary means to enforce societal and other goals in the regulated monopoly sector. The design of economic regulation is concerned with two main attributes; end-customer price and quality of electricity distribution services. Regulation limits the costs of the regulated company but also defines the desired quality of monopoly services. The characteristics of the regulatory framework and the incentives it provides are therefore decisive for the electricity distribution sector. Regulation is not a static factor; changes in the regulatory practices cause discontinuity points, which in turn generate risks. A variety of social and environmental concerns together with technological advancements have emphasised the relevance of quality regulation, which is expected to lead to the large-scale replacement of overhead lines with underground cables. The electricity network construction activity is therefore currently witnessing revolutionary changes in its competitive landscape. In a business characterised by high statutory involvement and a high level of sunk costs, recognising and understanding the regulatory risks becomes a key success factor. As a response, electricity distribution companies have turned into outsourcing to attain efficiency and quality goals. This doctoral thesis addresses the impacts of regulatory risks on electricity network construction, which is a commonly outsourced activity in the electricity distribution network sector. The chosen research approach is characterised as an action analytical research on account of the fact that regulatory risks are greatly dependent on the individual nature of the regulatory regime applied in the electricity distribution sector. The main contribution of this doctoral thesis is to develop a concept for recognising and managing the business risks stemming from economic regulation. The degree of outsourcing in the sector is expected to increase in years to come. The results of the research provide new knowledge to manage the regulatory risks when outsourcing services.

Aging based maintenance and reinvestment scheduling of electric distribution

The maintenance of electric distribution network is a topical question for distribution system operators because of increasing significance of failure costs. In this dissertation the maintenance practices of the distribution system operators are analyzed and a theory for scheduling maintenance activities and reinvestment of distribution components is created. The scheduling is based on the deterioration of components and the increasing failure rates due to aging. The dynamic programming algorithm is used as a solving method to maintenance problem which is caused by the increasing failure rates of the network. The other impacts of network maintenance like environmental and regulation reasons are not included to the scope of this thesis. Further the tree trimming of the corridors and the major disturbance of the network are not included to the problem optimized in this thesis. For optimizing, four dynamic programming models are presented and the models are tested. Programming is made in VBA-language to the computer. For testing two different kinds of test networks are used. Because electric distribution system operators want to operate with bigger component groups, optimal timing for component groups is also analyzed. A maintenance software package is created to apply the presented theories in practice. An overview of the program is presented.

Maintenance and construction outsourcing in a public-owned electricity network company

Euroopan sähkösektori on ollut viimeisen vuosikymmenen suurten mullistusten kourissa. Sähkömarkkinoiden avautumisen jälkeen monopoliliiketoimintaa harjoittavien sähköyhtiöiden on ollut pakko parantaa tuottavuuttaan. Ratkaisuksi tähän on etsitty apua huolto- ja rakennustoimintojen ulkoistamisella. Ulkoistaminen on kuitenkin uusi menetelmä tällä sektorilla. Tämän tutkielman tavoitteena on selvittää syyt, jotka tanskalaisella sähköverkkoyhtiöllä oli huolto- ja rakennustoimintojen ulkoistamiseen, sekä löytää siitä saatavat hyödyt ja siihen sisältyvät riskit. Tutkimus suoritetaan käyttäen apuna kirjallisuutta, saatavilla olevia due diligence-, sekä muita raportteja ja analyysejä, sekä tapausta koskettavien tahojen haastatteluja.Lisäksi sähköverkkoalan asiantuntijoiden kanssa käytyjä konsultointia käytetäänselvitykseen. Tutkimus osoittaa, että perimmäiset ajurit huolto- ja rakennustoimintojen ulkoistamiseen tulivat lainmuutosten ja vapautuneiden sähkömarkkinoiden asettamista paineista. Kunnallisessa organisaatiossa parantaa tehokkuutta ulkoistamalla jotain toimintoja yksityisomisteiselle palvelun tuottajalle. Muut ulkoistamisesta odotetut hyödyt olivat alentuneet kustannukset, virtaviivaisempi organisaation ja sähköverkkoyhtiön tehottomista osista eroon pääseminen ennen sen myymistä.

Russia's food retail sector from the point of view of Finnish food producers

This research paper focuses on the Russian food retail sector and its structure and development. At the momentit is one of the fastest growing markets today with 12.1% growth last year (2004). The growth originates from high oil price, which has been accumulated to people's wages. They are growing nominally more than 20% annually. But even though the income increases, the share of food of all retailtrade has been fairly stable with only a slight decline. Thus, the consumption is shifting to products with more quality and value. The shareof modern retail outlets is low, as the Russian retail sector is still very dispersed to traditional retail outlets such as kiosks, open markets and small grocery stores. The store chains are, however, becoming more and more significant. The biggest market for retailers is Moscow but nowadays the chains are expanding rapidly into other regions. Even though the markets have not been saturated in Moscow, the best prospects for growth are in the regions. The most important factor restricting the growth in Moscowis the availability of real estate and land plots for stores. The market is moving forward to saturation, and a consolidation process will follow. In fact, it has already started but not many acquisitions have been made so far. To this point the domestic chains have settled to form only alliances. The foreign players will be very strong in the tightening competition in the future. The problem of domestic chains is that the stores are nonstandardized, which is not cost-efficient. The chains are trying to enhance their power in price negotiations by forming purchasing alliances, introducing private label goods and using the regional expansion as a striking weapon. In order to follow the growing chains to other regions the producer must sell its products to the chains at favorable terms. Suppliers are strong in negotiations when they have a functioning distribution network, ability to JIT deliveries, proper documentationpolicies, a strong brand, reliability in deliveries and a fair price. The size of the entry ticket, i.e. the listing fee may define the shelf space a producer gets in the stores.

Change of Electricity Distribution Industry: Drivers and Opening Business Opportunities

As a result of the recent regulatory amendments and other development trends in the electricity distribution business, the sector is currently witnessing radical restructuring that will eventually impact the business logics of the sector. This report represents upcoming changes in the electricity distribution industry and concentrates on the factors that are expected to be the most fundamental ones. Electricity network companies nowadays struggle with legislative and regulatory requirements that focus on both the operational efficiency and the reliability of electricity distribution networks. The forces that have an impact on the distribution network companies can be put into three main categories that define the transformation at a general level. Those are: (1) a requirement for a more functional marketplace for energy, (2) environmental aspects (combating climate change etc.), and (3) a strongly emphasized requirement for the security of energy supply. The first point arises from the legislators’ attempt to increase competition in electricity retail markets, the second one concerns both environmental protection and human safety issues, and the third one indicates societies’ reduced willingness to accept interruptions in electricity supply. In the future, regulation of electricity distribution business may lower the threshold for building more weather-resistant networks, which in turn means increased underground cabling. This development pattern is reinforced by tightening safety and environmental regulations that ultimately make the overhead lines expensive to build and maintain. The changes will require new approaches particularly in network planning, construction, and maintenance. The concept for planning, constructing, and maintaining cable networks is necessary because the interdependencies between network operations are strong, in other words, the nature of the operation requires a linkage to other operations.

Tasasähkönjakeluverkon vaihtosuuntaaja galvaanisella erotuksella

Suomessa sähkönjakeluverkko koostuu pääasiassa 20 kV ja 400 V jännitetasoista. Tällöin sähkö viedään lähelle kuluttajia suuremmalla jännitetasolla ja muunnetaan alhaisemmaksi lähellä asiakkaita. Haittapuolena on se, että haja-asutusalueilla jakelumuuntajien määrä kasvaa suureksi, koska ne täytyy sijoittaa lähelle kuluttajaa. Vaihtoehtona on toteuttaa osa sähkönjakelusta tasajännitteellä, jolloin tehollinen jännite olisi suurempi. Tällöin sähköä voitaisiin siirtää pidempiä matkoja ilman, että asiakaskohtaisia tai muutaman asiakkaan kattavia 20 kV siirtolinjoja tarvitsisi käyttää. Tämä taasen edellyttää asiakaskohtaisien vaihtosuuntaajien käyttöä. Tässä työssä esiteltävällä 1 kVA vaihtosuuntaajalla muodostetaan tasasähköjakeluverkosta saatavasta 750 V tasasähköstä yksivaiheista (230 VRMS, 50 Hz) verkkojännitettä. Laite on suunniteltu toteuttamaan galvaaninen erotus mahdollisimman hyvän hyötysuhteen puitteissa. Vaihtosuuntaaja on toteutettu käyttämällä resonanssikonvertteria, joka vaihtosuuntaa jakelujännitteen korkeataajuiseksi vaihtojännitteeksi. Tämän jälkeen toteutetaan galvaaninen erotus käyttäen suurtaajuusmuuntajaa. Tätä seuraa syklokonvertteri, joka pulssintiheysmodulaatiota soveltaen muodostaa lähtöjännitteen. Tämä suodatetaan lopuksi LC- alipäästösuotimella säröltään standardin mukaiseksi. Laite on jaettu työssä kolmeen osaan, joista jokaisen toiminta on selitetty ja simuloitu itsenäisesti. Lopussa koko järjestelmä on simuloitu yhtenä kokonaisuutena. Hyötysuhteeksi arvioitiin karkeasti 94 % ja lopullisista tuloksista voidaan päätellä, että laitteen toteuttaminen prototyypiksi voisi olla kannattavaa.

Distribution development in global business environment

The purpose of this master’s thesis was to analyze a case company’s distribution and its elements. With different distribution structure options a customer can be served with different ways. However, cost elements and service elements create different trade-offs. In this work the case company’s distribution’s present state was analyzed and conclusions were made. Based on these conclusions different alternatives for distribution were created. These different alternatives were analyzed through simulations and with more traditional calculations to compose the total operative costs of each alternative. Also other aspects were considered, such as required organizational changes and the possible better customer service. With the suggested 3-stock distribution structure shorter delivery times and possibly more punctual deliveries for products kept in stock could be achieved with the same operative costs as in current direct delivery model. Also, similar benefits could be achieved with other products with the 3-stock model.

Galvaanisen erotuksen toteuttaminen tasavirtasähkönjakelun asiakaspäätelaitteessa

Suomessa sähkönjakeluverkon pääasialliset jännitetasot ovat 20 kV ja 400 V. 20 kV jännitetasolla sähkö viedään lähelle kuluttajia ja muunnetaan pienemmäksi lähellä asiakkaita. Haittapuolena on se, että 20 kV avojohtosähkönsiirtoverkko on hyvin vika-altis ja usein yhden haaran vikaantuessa monta muutakin jää ilman sähköä. Lisäksi hintavien ja suurien jakelumuuntajien määrä on suuri. Vaihtoehtona on toteuttaa osa sähkönjakelusta tasajännitteellä, jolloin tehollinen pienjännite olisi 400 V:a suurempi. Tällöin sähköä voitaisiin siirtää pidempiä matkoja ilman, että asiakaskohtaisia tai muutaman asiakkaan kattavia 20 kV siirtolinjoja tarvitsisi käyttää. Tämä edellyttää vaihtosuuntauksen toteuttamista kuluttajan päässä. Tässä työssä esiteltävällä 1 kVA:n tehoisella vaihtosuuntaajalla muodostetaan tasasähköjakeluverkosta saatavasta 750 V tasasähköstä yksivaiheista (230 VRMS, 50 Hz) verkkojännitettä. Laite on suunniteltu toteuttamaan galvaaninen erotus mahdollisimman hyvällä hyötysuhteella. Suurtaajuusmuuntajan mitoitus mahdollisimman hyvälle hyötysuhteelle on haastava tehtävä, koska vaatimuksia sille asettavat sekä syöttävä resonanssikonvertteri että syötettävä syklokonvertteri. Mitoituksessa on pyrittävä löytämään mahdollisimman hyvä hyötysuhde kustannusten ja toteutettavuuden suhteen.