Numerical Investigation of Flow Past a Circular Cylinder and in a Staggered Tube Bundle Using Various Turbulence Models

Transitional flow past a three-dimensional circular cylinder is a widely studied phenomenon since this problem is of interest with respect to many technical applications. In the present work, the numerical simulation of flow past a circular cylinder, performed by using a commercial CFD code (ANSYS Fluent 12.1) with large eddy simulation (LES) and RANS (κ - ε and Shear-Stress Transport (SST) κ - ω! model) approaches. The turbulent flow for ReD = 1000 & 3900 is simulated to investigate the force coefficient, Strouhal number, flow separation angle, pressure distribution on cylinder and the complex three dimensional vortex shedding of the cylinder wake region. The numerical results extracted from these simulations have good agreement with the experimental data (Zdravkovich, 1997). Moreover, grid refinement and time-step influence have been examined. Numerical calculations of turbulent cross-flow in a staggered tube bundle continues to attract interest due to its importance in the engineering application as well as the fact that this complex flow represents a challenging problem for CFD. In the present work a time dependent simulation using κ – ε, κ - ω! and SST models are performed in two dimensional for a subcritical flow through a staggered tube bundle. The predicted turbulence statistics (mean and r.m.s velocities) have good agreement with the experimental data (S. Balabani, 1996). Turbulent quantities such as turbulent kinetic energy and dissipation rate are predicted using RANS models and compared with each other. The sensitivity of grid and time-step size have been analyzed. Model constants sensitivity study have been carried out by adopting κ – ε model. It has been observed that model constants are very sensitive to turbulence statistics and turbulent quantities.

Two-phase flow measurements with spacer grid in a rod bundle geometry

Heat transfer effectiveness in nuclear rod bundles is of great importance to nuclear reactor safety and economics. An important design parameter is the Critical Heat Flux (CHF), which limits the transferred heat from the fuel to the coolant. The CHF is determined by flow behaviour, especially the turbulence created inside the fuel rod bundle. Adiabatic experiments can be used to characterize the flow behaviour separately from the heat transfer phenomena in diabatic flow. To enhance the turbulence, mixing vanes are attached to spacer grids, which hold the rods in place. The vanes either make the flow swirl around a single sub-channel or induce cross-mixing between adjacent sub-channels. In adiabatic two-phase conditions an important phenomenon that can be investigated is the effect of the spacer on canceling the lift force, which collects the small bubbles to the rod surfaces leading to decreased CHF in diabatic conditions and thus limits the reactor power. Computational Fluid Dynamics (CFD) can be used to simulate the flow numerically and to test how different spacer configurations affect the flow. Experimental data is needed to validate and verify the used CFD models. Especially the modeling of turbulence is challenging even for single-phase flow inside the complex sub-channel geometry. In two-phase flow other factors such as bubble dynamics further complicate the modeling. To investigate the spacer grid effect on two-phase flow, and to provide further experimental data for CFD validation, a series of experiments was run on an adiabatic sub-channel flow loop using a duct-type spacer grid with different configurations. Utilizing the wire-mesh sensor technology, the facility gives high resolution experimental data in both time and space. The experimental results indicate that the duct-type spacer grid is less effective in canceling the lift force effect than the egg-crate type spacer tested earlier.

Effects of Fin Parameters on Gas-Side Heat Transfer Performance of H-Type Finned Tube Bundle in a Waste Heat Recovery Boiler

Alfa Laval Aalborg Oy designs and manufactures waste heat recovery systems utilizing extended surfaces. The waste heat recovery boiler considered in this thesis is a water-tube boiler where exhaust gas is used as the convective heat transfer medium and water or steam flowing inside the tubes is subject to cross-flow. This thesis aims to contribute to the design of waste heat recovery boiler unit by developing a numerical model of the H-type finned tube bundle currently used by Alfa Laval Aalborg Oy to evaluate the gas-side heat transfer performance. The main objective is to identify weaknesses and potential areas of development in the current H-type finned tube design. In addition, numerical simulations for a total of 15 cases with varying geometric parameters are conducted to investigate the heat transfer and pressure drop performance dependent on H-type fin geometry. The investigated geometric parameters include fin width and height, fin spacing, and fin thickness. Comparison between single and double tube type configuration is also conducted. Based on the simulation results, the local heat transfer and flow behaviour of the H-type finned tube is presented including boundary layer development between the fins, the formation of recirculation zone behind the tubes, and the local variations of flow velocity and temperature within the tube bundle and on the fin surface. Moreover, an evaluation of the effects of various fin parameters on heat transfer and pressure drop performance of H-type finned tube bundle has been provided. It was concluded that from the studied parameters fin spacing and fin width had the most significant effect on tube bundle performance and the effect of fin thickness was the least important. Furthermore, the results suggested that the heat transfer performance would increase due to enhanced turbulence if the current double tube configuration is replaced with single tube configuration, but further investigation and experimental measurements are required in order to validate the results.

Energiantuotanto kuivalla puupolttoaineella

Diplomityössä esitetään taustatietona puupolttoaineen ominaisuuksien vaikutusta energiantuotantolaitoksen mitoitukseen ja käyttöön. Työssä esitellään ensimmäisessä vaiheessa tehty laskentamalli, jolla on tehty 20 MW laitoksen mitoitus kolmelle eri polttoaineen kosteudelle. Mitoitustulosten perusteella määritellään jokaiselle laitokselle energiantuotantohinta, joita vertaillaan. Vertailun avulla saadaan tieto siitä, onko uusi laitos syytä mitoittaa kuivatulle puupolttoaineelle investointisäästöjen vuoksi. Työssä tarkastellaan myös risutukkien ominaisuuksia, hyödyntämismahdollisuuksia sekä niiden varastokuivatuksen taloudellisuutta.

Calculations of Boiling Two-Phase Flow Using a Porous Media Model

Boiling two-phase flow and the equations governing the motion of fluid in two-phase flows are discussed in this thesis. Disposition of the governing equations in three-dimensional complex geometries is considered from the perspective of the porous medium concept. The equations governing motion in two-phase flows were formulated, discretized and implemented in a subroutine for pressure-velocity solution utilizing the SIMPLE algorithm modified for two-phase flow. The subroutine was included in PORFLO, which is a three-dimensional 5-equation porous media model developed at VTT by Jaakko Miettinen. The development of two-phase flow and the resulting void fraction distribution was predicted in a geometry resembling a section of BWR fuel bundle in a couple of test cases using PORFLO.

Managing the Front End of Innovation in a Networked Company Environment - Combining Strategy, Processes and Systems of Innovation

The objective of the thesis is to enhance the understanding about the management of the front end phases of the innovation process in a networked environment. The thesis approaches the front end of innovation from three perspectives, including the strategy, processes and systems of innovation. The purpose of the use of different perspectives in the thesis is that of providing an extensive systemic view of the front end, and uncovering the complex nature of innovation management. The context of the research is the networked operating environment of firms. The unit of analysis is the firm itself or its innovation processes, which means that this research approaches the innovation networks from the point of view of a firm. The strategy perspective of the thesis emphasises the importance of purposeful innovation management, the innovation strategy of firms. The role of innovation processes is critical in carrying out innovation strategies in practice, supporting the development of organizational routines for innovation, and driving the strategic renewal of companies. The primary focus of the thesis from systems perspective is on idea management systems, which are defined as a part of innovation management systems, and defined for this thesis as any working combination of methodology and tools (manual or IT-supported) that enhance the management of innovations within their early phases. The main contribution of the thesis are the managerial frameworks developed for managing the front end of innovation, which purposefully “wire” the front end of innovation into the strategy and business processes of a firm. The thesis contributes to modern innovation management by connecting the internal and external collaboration networks as foundational elements for successful management of the early phases of innovation processes in a dynamic environment. The innovation capability of a firm is largely defined by its ability to rely on and make use of internal and external collaboration already during the front end activities, which by definition include opportunity identification and analysis, idea generation, profileration and selection, and concept definition. More specifically, coordination of the interfaces between these activities, and between the internal and external innovation environments of a firm is emphasised. The role of information systems, in particular idea management systems, is to support and delineate the innovation-oriented behaviour and interaction of individuals and organizations during front end activities. The findings and frameworks developed in the thesis can be used by companies for purposeful promotion of their front end processes. The thesis provides a systemic strategy framework for managing the front end of innovation – not as a separate process, but as an elemental bundle ofactivities that is closely linked to the overall innovation process and strategy of a firm in a distributed environment. The theoretical contribution of the thesis relies on the advancement of the open innovation paradigm in the strategic context of a firm within its internal and external innovation environments. This thesis applies the constructive research approach and case study methodology to provide theoretically significant results, which are also practically beneficial.

Kuusiviilun esikuivaus puristamalla

Tutkimuksen lähtökohtana oli selvittää, voidaanko viilun valmistusprosessiin liittää uusi työvaihe, viilun esikuivaus. Esikuivauksen tarkoituksena on poistaa kosteutta viiluista ennen varsinaista kuivausta ja lisätä näin kuivauskapasiteettia. Tehdyissä tutkimuksissa viilut esikuivattiin nipuissa puristamalla. Muuttujina esikuivauksessa toimivat puristusaika ja -paine. Niiden määrittelyn lähtökohtana pidettiin sitä, etteivät viilun ominaisuudet saa merkittävästi heikentyä esikuivauksen aikana ja samalla viiluista on saatava mahdollisimman paljon kosteutta pois. Aikaisempien tutkimusten avulla selvitettiin vanerin valmistuksen, viilun kuivauksen sekä viilun esikuivauksen teoriaa. Lisäksi selvitettiin puun ominaisuuksien antamia mahdollisuuksia ja rajoitteita esikuivaukseen liittyen. Tutkimus koostui kahdesta osasta: laboratorio- ja tehdastutkimuksista. Laboratoriotutkimuksen tarkoituksena oli toimia tehdastutkimuksen esitutkimuksena. Laboratoriotutkimuksessa tutkittiin ainoastaan esikuivauksen vaikutusta märille viiluille. Tehdastutkimusosiossa esikuivatuista viiluista valmistettiin normaalin vanerinvalmistusprosessin kautta levyjä, joiden ominaisuuksia verrattiin normaaleista viiluista valmistettuihin vanereihin. Viilujen esikuivauksen todettiin pienentävän kuusiviilujen kosteuspitoisuutta. Tämän lisäksi kosteuspitoisuuden muutokset esikuivauksen aikana tapahtuivat tasaisesti niin yksittäisen viilun kuin viilunipunkin sisällä. Esikuivatuista viiluista valmistetut vanerilevyt täyttivät kaikki standardien sekä vanerin laadunvalvontasopimuksen asettamat vaatimukset. Esikuivauksen haitaksi tutkimuksissa todettiin viilun paksuuden pienentymä. Ennen esikuivauksen soveltamista teolliseen käyttöön nähtiin tarvetta lisätutkimukselle, jossa tulisi selvittää suurempien viilunippukokojen esikuivaamista sekä niiden varsinaista kuivaamista heti esikuivauksen jälkeen.

The concept of solution: Industry’s insights compared to theoretical views

Many manufacturing companies have started to offer complete solutions to their customers’ unique needs due to toughening competition and customer demand. Discourse on this kind of solution business is still developing, hence, there is not an established definition for the concept of solution. The aim of the study is to profoundly identify the concept of solution and to understand how the industry’s current views differ from the theoretical concepts. The describing dimensions are identified from selected 13 theoretical notions, and from responses, that the employees of five different companies have given. The 32 interview transcripts are analyzed with thematic analysis and qualitative content analysis. According to the findings, the concept of solution is characterized by integration, customization, risk-sharing, value co-creation, long-term orientation, and desired outcomes. The industry’s insights differ in terms of them all. The results illustrate, that a solution is a bundle, and the whole solution is customized on some level for a client. A solution supplier needs to be customer-focused, in which value co-creation is only a part. The solution solves the customer’s problem, and improves both the customer’s, and the supplier’s business. Neither long-term focus nor risks-sharing were directly employed to characterize the concept of solution. Differences are mainly due to the different approaches to the definitions and inexperience of the companies.

Uittonippujen sidelangan valinta ja sitomiskonstruktion suunnittelu

Työssä suunniteltiin uittonippujen sidonnan koneellistamiseksi tarvittavan sidontalangan käsittelylaitteisto. Sen toiminnalliset pääkomponentit ovat langan ohjauskouru, syöttölaite sekä solminta- ja katkaisulaitteet. Lisäksi työssä tehtiin koneelliseen sidontaan sopivan sidontalangan määrityksiä.

Developing customer need based services in personal security service industry

The purpose of this thesis is to examine how services can be developed and how the voice of the customer can be incorporated to the strategic planning of services. Furthermore, the objective is to investigate the methods of customer need analysis and service bundling. The data is collected from secondary and primary sources by reviewing the existing academic literature and by conducting in-depth interviews and surveys. The main findings of this research indicate that the service development in personal security service industry should be conducted through a formalized process and the process should begin with setting the strategic objectives. Moreover, the voice of the customer should be incorporated into all stages of the development process, especially into the front-end of the process. Furthermore, the information on customer needs should be gathered in a manner tailored for the purposes of service development.

Immediate Decision-Making and Information Needs in Intensive Care Coordination

The aim of this study was to develop a theoretical model for information integration to support the deci¬sion making of intensive care charge nurses, and physicians in charge – that is, ICU shift leaders. The study focused on the ad hoc decision-making and immediate information needs of shift leaders during the management of an intensive care unit’s (ICU) daily activities. The term ‘ad hoc decision-making’ was defined as critical judgements that are needed for a specific purpose at a precise moment with the goal of ensuring instant and adequate patient care and a fluent flow of ICU activities. Data collection and research analysis methods were tested in the identification of ICU shift leaders’ ad hoc decision-making. Decision-making of ICU charge nurses (n = 12) and physicians in charge (n = 8) was observed using a think-aloud technique in two university-affiliated Finnish ICUs for adults. The ad hoc decisions of ICU shift leaders were identified using an application of protocol analysis. In the next phase, a structured online question¬naire was developed to evaluate the immediate information needs of ICU shift leaders. A national survey was conducted in all Finnish, university-affiliated hospital ICUs for adults (n = 17). The questionnaire was sent to all charge nurses (n = 515) and physicians in charge (n = 223). Altogether, 257 charge nurses (50%) and 96 physicians in charge (43%) responded to the survey. The survey was also tested internationally in 16 Greek ICUs. From Greece, 50 charge nurses out of 240 (21%) responded to the survey. A think-aloud technique and protocol analysis were found to be applicable for the identification of the ad hoc decision-making of ICU shift leaders. During one day shift leaders made over 200 ad hoc decisions. Ad hoc decisions were made horizontally, related to the whole intensive care process, and vertically, concerning single intensive care incidents. Most of the ICU shift leaders’ ad hoc decisions were related to human resources and know-how, patient information and vital signs, and special treatments. Commonly, this ad hoc decision-making involved several multiprofessional decisions that constituted a bundle of immediate decisions and various information needs. Some of these immediate information needs were shared between the charge nurses and the physicians in charge. The majority of which concerned patient admission, the organisation and management of work, and staff allocation. In general, the information needs of charge nurses were more varied than those of physicians. It was found that many ad hoc deci-sions made by the physicians in charge produced several information needs for ICU charge nurses. This meant that before the task at hand was completed, various kinds of information was sought by the charge nurses to support the decision-making process. Most of the immediate information needs of charge nurses were related to the organisation and management of work and human resources, whereas the information needs of the physicians in charge mainly concerned direct patient care. Thus, information needs differ between professionals even if the goal of decision-making is the same. The results of the international survey confirmed these study results for charge nurses. Both in Finland and in Greece the information needs of charge nurses focused on the organisation and management of work and human resources. Many of the most crucial information needs of Finnish and Greek ICU charge nurses were common. In conclusion, it was found that ICU shift leaders make hundreds of ad hoc decisions during the course of a day related to the allocation of resources and organisation of patient care. The ad hoc decision-making of ICU shift leaders is a complex multi-professional process, which requires a lot of immediate information. Real-time support for information related to patient admission, the organisation and man¬agement of work, and allocation of staff resources is especially needed. The preliminary information integration model can be applied when real-time enterprise resource planning systems are developed for intensive care daily management

Mobile clinics in public health care: Integrated service offerings for rural elderly

This research is an analysis of the value and content of local service offerings that enable longer periods of living at home for elderly people. Mobile health care and new distribution services have provided an interesting solution in this context. The research aim to shed light on the research question, ‘How do we bundle services based on different customer needs?’ A research process consisting of three main phases was applied for this purpose. During this process, elderly customers were segmented, the importance of services was rated and service offerings were defined. Value creation and service offering provides theoretical framework for the research. The target group is South Karelia’s 60 to 90-year old individuals and the data has been acquired via a postal questionnaire. Research has been conducted as exploratory research utilizing the methods of quantitative and social network analysis. The main results of the report are identified customer segments and service packages that fits to the segments’ needs. The results indicate the needs of customers and the results are additionally analysed from the producer’s point of view. In addition to the empirical results, the used theory framework has been developed further in order for the service-related theories to be seen from the customer’s point of view and not just from the producer’s point of view.

Effects of obtained benefits on willingness to pay and word-of-mouth behavior in newspaper industry

The purpose of this master’s thesis was to investigate the effects which benefits obtained from reading a newspaper and using its website have on behavioral outcomes such as word-of-mouth behavior and willingness to pay. Several other antecedents of willingness to pay have been used as the control variables. However, their interrelations haven’t been hypothesized. The empirical part focused on a case company – Finnish regional newspaper. Empirical research has been conducted using a quantitative method and data was collected via online survey placed on newspaper’s website during 2010. 1001 responses have been collected. The results showed that benefits obtained both from traditional printed newspaper and from online one have positive effects on the word-of-mouth about this newspaper and its website. However, it has been revealed that benefits obtained from reading the newspaper don’t have effect on the willingness to pay for this newspaper. Additionally, only interpersonal and convenience benefits obtained from using the newspaper’s website influence on the willingness to pay for it. Finally, willingness to pay for the bundle of printed newspaper and its website access is affected positively only by the information/learning benefits obtained from reading the newspaper and by the interpersonal benefits obtained from using the newspaper’s website.