The Detector Control Systems for the CMS Resistive Plate Chamber at LHC

The RPC Detector Control System (RCS) is the main subject of this PhD work. The project, involving the Lappeenranta University of Technology, the Warsaw University and INFN of Naples, is aimed to integrate the different subsystems for the RPC detector and its trigger chain in order to develop a common framework to control and monitoring the different parts. In this project, I have been strongly involved during the last three years on the hardware and software development, construction and commissioning as main responsible and coordinator. The CMS Resistive Plate Chambers (RPC) system consists of 912 double-gap chambers at its start-up in middle of 2008. A continuous control and monitoring of the detector, the trigger and all the ancillary sub-systems (high voltages, low voltages, environmental, gas, and cooling), is required to achieve the operational stability and reliability of a so large and complex detector and trigger system. Role of the RPC Detector Control System is to monitor the detector conditions and performance, control and monitor all subsystems related to RPC and their electronics and store all the information in a dedicated database, called Condition DB. Therefore the RPC DCS system has to assure the safe and correct operation of the sub-detectors during all CMS life time (more than 10 year), detect abnormal and harmful situations and take protective and automatic actions to minimize consequential damages. The analysis of the requirements and project challenges, the architecture design and its development as well as the calibration and commissioning phases represent themain tasks of the work developed for this PhD thesis. Different technologies, middleware and solutions has been studied and adopted in the design and development of the different components and a big challenging consisted in the integration of these different parts each other and in the general CMS control system and data acquisition framework. Therefore, the RCS installation and commissioning phase as well as its performance and the first results, obtained during the last three years CMS cosmic runs, will be

Trimmerin kapasiteetin kasvattaminen dynamiikan mallinnuksen avulla

Työn tavoitteena oli kasvattaa sahan dimensiolaitoksella käytettävän trimmerin rakenteellista kapasiteettia. Tavoitteeseen pyrittiin modernisoimalla trimmerin teräyksikköä käyttävää toimilaite ja teräyksikön säätö dynamiikan mallinnuksen avulla. Trimmerin teräyksikön dynamiikka mallinnettiin MATLAB-matematiikkaohjelmistolla kaksiulotteisena kinematiikkamallina ja kolmeulotteisena kinetiikkamallina. Dynamiikkamallien tulosten perusteella valittin teräyksikköä käyttävä toimilaite komponentteineen. Kinetiikkamalliin mallinnettiin trimmeriä käyttävä hydraulipiiri valittuine komponentteineen keskittyneiden paineiden ja puoliempiirisen mallinnuksen periaatteita käyttäen. Teräyksikön työkiertoa säätämään mallinnettiin suljettu takaisinkytketty säätöpiiri. Tuloksien perusteella valittiin optimaalinen toimilaitteen asemointigeometria ja todettiin mallinnetun järjestelmän täyttävän asetetut vaatimukset. Järjestelmää testattiin muuttamalla jarjestelman parametreja ja tutkimalla muutosten vaikutuksia jarjestelman toimintaan. Lisaksi tutkittiin lyhyesti terayksikon rakenteen keventamisen vaikutuksia.

Flexible multibody dynamics and intelligent control of a hydraulically driven hybrid redundant robot machine

The assembly and maintenance of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel (VV) is highly challenging since the tasks performed by the robot involve welding, material handling, and machine cutting from inside the VV. The VV is made of stainless steel, which has poor machinability and tends to work harden very rapidly, and all the machining operations need to be carried out from inside of the ITER VV. A general industrial robot cannot be used due to its poor stiffness in the heavy duty machining process, and this will cause many problems, such as poor surface quality, tool damage, low accuracy. Therefore, one of the most suitable options should be a light weight mobile robot which is able to move around inside of the VV and perform different machining tasks by replacing different cutting tools. Reducing the mass of the robot manipulators offers many advantages: reduced material costs, reduced power consumption, the possibility of using smaller actuators, and a higher payload-to-robot weight ratio. Offsetting these advantages, the lighter weight robot is more flexible, which makes it more difficult to control. To achieve good machining surface quality, the tracking of the end effector must be accurate, and an accurate model for a more flexible robot must be constructed. This thesis studies the dynamics and control of a 10 degree-of-freedom (DOF) redundant hybrid robot (4-DOF serial mechanism and 6-DOF 6-UPS hexapod parallel mechanisms) hydraulically driven with flexible rods under the influence of machining forces. Firstly, the flexibility of the bodies is described using the floating frame of reference method (FFRF). A finite element model (FEM) provided the Craig-Bampton (CB) modes needed for the FFRF. A dynamic model of the system of six closed loop mechanisms was assembled using the constrained Lagrange equations and the Lagrange multiplier method. Subsequently, the reaction forces between the parallel and serial parts were used to study the dynamics of the serial robot. A PID control based on position predictions was implemented independently to control the hydraulic cylinders of the robot. Secondly, in machining, to achieve greater end effector trajectory tracking accuracy for surface quality, a robust control of the actuators for the flexible link has to be deduced. This thesis investigates the intelligent control of a hydraulically driven parallel robot part based on the dynamic model and two schemes of intelligent control for a hydraulically driven parallel mechanism based on the dynamic model: (1) a fuzzy-PID self-tuning controller composed of the conventional PID control and with fuzzy logic, and (2) adaptive neuro-fuzzy inference system-PID (ANFIS-PID) self-tuning of the gains of the PID controller, which are implemented independently to control each hydraulic cylinder of the parallel mechanism based on rod length predictions. The serial component of the hybrid robot can be analyzed using the equilibrium of reaction forces at the universal joint connections of the hexa-element. To achieve precise positional control of the end effector for maximum precision machining, the hydraulic cylinder should be controlled to hold the hexa-element. Thirdly, a finite element approach of multibody systems using the Special Euclidean group SE(3) framework is presented for a parallel mechanism with flexible piston rods under the influence of machining forces. The flexibility of the bodies is described using the nonlinear interpolation method with an exponential map. The equations of motion take the form of a differential algebraic equation on a Lie group, which is solved using a Lie group time integration scheme. The method relies on the local description of motions, so that it provides a singularity-free formulation, and no parameterization of the nodal variables needs to be introduced. The flexible slider constraint is formulated using a Lie group and used for modeling a flexible rod sliding inside a cylinder. The dynamic model of the system of six closed loop mechanisms was assembled using Hamilton’s principle and the Lagrange multiplier method. A linearized hydraulic control system based on rod length predictions was implemented independently to control the hydraulic cylinders. Consequently, the results of the simulations demonstrating the behavior of the robot machine are presented for each case study. In conclusion, this thesis studies the dynamic analysis of a special hybrid (serialparallel) robot for the above-mentioned special task involving the ITER and investigates different control algorithms that can significantly improve machining performance. These analyses and results provide valuable insight into the design and control of the parallel robot with flexible rods.

Supersaturation-controlled crystallization

Identification of product requirements and quality, together with the management of production are key issues in chemical engineering. Quality control of crystalline products is part of the quality of many industrially manufactured products like paper, paintings, medicines and fertilizers. In most crystallization cases, quality is described with the size, polymorph, shape and purity of the crystal. The chemical composition, hydrodynamics and driving force, together with the operating temperature are in a key position when the properties of a crystalline product are controlled with the crystallization process. This study concentrates on managing the identified properties of a crystalline product with the control of a driving force. The controlling of the driving force can be based on the change of solubility or the change of concentration. Solubility can be changed with temperature, pressure and an antisolvent. The concentration of crystallizing compound, the solute can be changed with the evaporation of the solvent and with the addition of a reagent. The present study focuses on reagent addition and temperature change as methods of changing the level of the driving force. Three control structures for direct control of supersaturation are built, one for cooling crystallization and two for reactive crystallization. Closed loop feedback control structures are based on the measurement of the solute concentration with attenuated total reflection - Fourier transform infrared spectrometer. The details of the reagent feed are analyzed with experimental studies and with results of computational fluid dynamic simulations of the inert particle pulse in the premixer and inert particle injection to the mixing tank. Nucleation in conditions of controlled reactive crystallization is analyzed with Nielsen’s equation of homogeneous nucleation. The resulting control systems, based on regulation of supersaturation, can be used to produce the desired polymorph of an organic product. The polymorph composition of product crystals is controlled repeatably with the decision of a set value of supersaturation level.

Servo drive in hoist application

The objective of this master thesis is to test according to hoisting requirements, a servo drive system and compare its performance with the performance of a drive equipped with a vector controlled frequency converter. Both systems utilize closed-loop vector control based on PCL program control. In order to compare the results of tests both systems were connected to the same motor driving a variable speed electrical chain hoist. Tests were based on requirements to both systems. As requirements of tests zero speed operation, operation in field weakening, positioning accuracy and smoothness of motion are taken into consideration. Both systems demonstrate quite similar performance and meet the requirements. Servo drive system demonstrates a high positioning accuracy and dynamic performance. Frequency converter is not able to provide the same positioning accuracy and dynamic performance as servo drive.

Design of traction transmission and suspension systems for an omni-directional mobile robot

This project aims to design and manufacture a mobile robot with two Universal Robot UR10 mainly used indoors. In order to obtain omni-directional maneuverability, the mobile robot is constructed with Mecanum wheels. The Mecanum wheel can move in any direction with a series of rollers attached to itself. These rollers are angled at 45º about the hub’s circumference. This type of wheels can be used in both driving and steering with their any-direction property. This paper is focused on the design of traction system and suspension system, and the velocity control of Mecanum wheels in the close-loop control system. The mechanical design includes selection of bearing housing, couplers which are act as connection between shafts, motor parts, and other needed components. The 3D design software SolidWorks is utilized to assemble all the components in order to get correct tolerance. The driving shaft is designed based on assembled structure via the software as well. The design of suspension system is to compensate the assembly error of Mecanum wheels to guarantee the stability of the robot. The control system of motor drivers is realized through the Robot Operating System (ROS) on Ubuntu Linux. The purpose of inverse kinematics is to obtain the relationship among the movements of all Mecanum wheels. Via programming and interacting with the computer, the robot could move with required speed and direction.

Failure modes of passive decay heat removing safety systems of modern nuclear power plants

The purpose of this master’s thesis is to gain an understanding of passive safety systems’ role in modern nuclear reactors projects and to research the failure modes of passive decay heat removal safety systems which use phenomenon of natural circulation. Another purpose is to identify the main physical principles and phenomena which are used to establish passive safety tools in nuclear power plants. The work describes passive decay heat removal systems used in AES-2006 project and focuses on the behavior of SPOT PG system. The descriptions of the main large-scale research facilities of the passive safety systems of the AES-2006 power plant are also included. The work contains the calculations of the SPOT PG system, which was modeled with thermal-hydraulic system code TRACE. The dimensions of the calculation model are set according to the dimensions of the real SPOT PG system. In these calculations three parameters are investigated as a function of decay heat power: the pressure of the system, the natural circulation mass flow rate around the closed loop, and the level of liquid in the downcomer. The purpose of the calculations is to test the ability of the SPOT PG system to remove the decay heat from the primary side of the nuclear reactor in case of failure of one, two, or three loops out of four. The calculations show that three loops of the SPOT PG system have adequate capacity to provide the necessary level of safety. In conclusion, the work supports the view that passive systems could be widely spread in modern nuclear projects.

Stability Evaluation of a Paper Machine Wet End

Työssä analysoidaanprosessin vaikutusta paperikoneen stabiiliuteen. Kaksi modernia sanomalehtipaperikonetta analysoitiin ja sen perusteella molemmista prosesseista rakennettiin fysiikan lakeihin perustuvat simulointimallit APROS Paper simulointiohjelmistolla. Työn tavoitteena on selvittää, miten kyseisten koneiden prosessit eroavat toisistaan ja arvioida, miten havaitut erot vaikuttavat prosessien stabiiliuteen. Työssä tarkastellaan periodisten häiriöiden vaimenemista prosessissa. Simuloinnissa herätteenä käytettiin puhdasta valkoista kohinaa, jonka avulla eri taajuistenperiodisten häiriöiden vaimenemista analysoitiin. Prosessien häiriövasteet esitetään taajuuskoordinaatistossa. Suurimmat erot prosessien välillä löytyivät viirakaivosta ja sen sekoitusdynamiikasta. Perinteisen viirakaivon todettiin muistuttavan käyttäytymiseltään sarjaan kytkettyjä ideaalisekoittimia, kun taas pienempitilavuuksisen fluumin todettiin käyttäytyvän lähes kuin putkiviive. Vaikka erotprosessitilavuudessa sekä viirakaivon sekoitusdynamiikassa olivat hyvin selkeät, havaittiin vain marginaalinen ero prosessin välillä periodisten häiriöiden vaimenemisessa, koska erot viiraretentiotasoissa vaikuttivat eniten simulointituloksia. Matalammalla viiraretentiolla operoivan paperikoneen todettiin vaimentavan tehokkaammin prosessihäiriöitä. Samalla retentiotasolla pienempitilavuuksisen prosessin todettiin vaimentavan hitaita prosessihäiriöitä marginaalisesti paremmin. Tutkituista paperikoneista toisella simuloitiin viiraosan vedenpoistomuutoksenvaikutusta viiraretentioon ja paperin koostumukseen. Lisäksi arvioitiin viiraretention säädön toimivuutta. Viiraosan listakengän vedenpoiston todettiin aiheuttavan merkittäviä sakeus- ja retentiohäiriöitä, mikäli sen avulla poistettavan kiintoaineen virtaus tuplaantuisi. Viiraretention säädön todettiin estävän häiriöiden kierron prosessissa, mutta siirtävän ne suoraan rainaan. Retention säädön eikuitenkaan todettu olevan suoranainen häiriön lähde.

Field Sales Management Control: Towards a Multi-Level Theory

The purpose of this dissertation is to increase the understanding and knowledge of field sales management control systems (i.e. sales managers monitoring, directing, evaluating and rewarding activities) and their potential consequences on salespeople. This topic is important because research conducted in the past has indicated that the choice of control system type can on the other hand have desirable consequences, such as high levels of motivation and performance, and on the other hand leadto harmful unintended consequences, such as opportunistic or unethical behaviors. Despite the fact that marketing and sales management control systems have been under rigorous research for over two decades, it still is at a very early stage of development, and several inconsistencies can be found in the research results. This dissertation argues that these inconsistencies are mainly derived from misspecification of the level of analysis in the past research. These different levels of analysis (i.e. strategic, tactical, and operational levels) involve very different decision-making situations regarding the control and motivation of sales force, which should be taken into consideration when conceptualizing the control. Moreover, the study of salesperson consequences of a field sales management control system is actually a cross-level phenomenon, which means that at least two levels of analysis are simultaneously involved. The results of this dissertation confirm the need to re-conceptualize the field sales management control system concept. It provides empirical evidence for the assertion that control should be conceptualized with more details atthe tactical/operational level of analysis than at the strategic levelof analysis. Moreover, the results show that some controls are more efficiently communicated to field salespeople than others. It is proposed that this difference is due to different purposes of control; some controls aredesigned for influencing salespersons' behavior (aim at motivating) whereas some controls are designed to aid decision-making (aim at providing information). According to the empirical results of this dissertation, the both types of controls have an impact to the sales force, but this impactis not as strong as expected. The results obtained in this dissertation shed some light to the nature of field sales management control systems, and their consequences on salespeopl

Improving Dynamic Characteristics of Open-loop Controlled Log Crane

The improvement of the dynamics of flexible manipulators like log cranes often requires advanced control methods. This thesis discusses the vibration problems in the cranes used in commercial forestry machines. Two control methods, adaptive filtering and semi-active damping, are presented. The adaptive filter uses a part of the lowest natural frequency of the crane as a filtering frequency. The payload estimation algorithm, filtering of control signal and algorithm for calculation of the lowest natural frequency of the crane are presented. The semi-active damping method is basedon pressure feedback. The pressure vibration, scaled with suitable gain, is added to the control signal of the valve of the lift cylinder to suppress vibrations. The adaptive filter cuts off high frequency impulses coming from the operatorand semi-active damping suppresses the crane?s oscillation, which is often caused by some external disturbance. In field tests performed on the crane, a correctly tuned (25 % tuning) adaptive filter reduced pressure vibration by 14-17 % and semi-active damping correspondingly by 21-43%. Applying of these methods require auxiliary transducers, installed in specific points in the crane, and electronically controlled directional control valves.

Converter-flux-based current control of voltage source PWM rectifiers - analysis and implementation

Pulsewidth-modulated (PWM) rectifier technology is increasingly used in industrial applications like variable-speed motor drives, since it offers several desired features such as sinusoidal input currents, controllable power factor, bidirectional power flow and high quality DC output voltage. To achieve these features,however, an effective control system with fast and accurate current and DC voltage responses is required. From various control strategies proposed to meet these control objectives, in most cases the commonly known principle of the synchronous-frame current vector control along with some space-vector PWM scheme have been applied. Recently, however, new control approaches analogous to the well-established direct torque control (DTC) method for electrical machines have also emerged to implement a high-performance PWM rectifier. In this thesis the concepts of classical synchronous-frame current control and DTC-based PWM rectifier control are combined and a new converter-flux-based current control (CFCC) scheme is introduced. To achieve sufficient dynamic performance and to ensure a stable operation, the proposed control system is thoroughly analysed and simple rules for the controller design are suggested. Special attention is paid to the estimationof the converter flux, which is the key element of converter-flux-based control. Discrete-time implementation is also discussed. Line-voltage-sensorless reactive reactive power control methods for the L- and LCL-type line filters are presented. For the L-filter an open-loop control law for the d-axis current referenceis proposed. In the case of the LCL-filter the combined open-loop control and feedback control is proposed. The influence of the erroneous filter parameter estimates on the accuracy of the developed control schemes is also discussed. A newzero vector selection rule for suppressing the zero-sequence current in parallel-connected PWM rectifiers is proposed. With this method a truly standalone and independent control of the converter units is allowed and traditional transformer isolation and synchronised-control-based solutions are avoided. The implementation requires only one additional current sensor. The proposed schemes are evaluated by the simulations and laboratory experiments. A satisfactory performance and good agreement between the theory and practice are demonstrated.

Development of Servo Hydraulics of Veneer Lathe

Diplomityö tehtiin kansainväliseen, mekaanisen puunjalostusteollisuuden koneita, tuotantojärjestelmiä ja tehtaita toimittavaan yritykseen. Diplomityön tarkoituksena oli kartoittaa syitä viilusorvin teräpenkin asemoinnissa esiintyneisiin värähtelyongelmiin ja tutkia ratkaisuja niiden voittamiseksi, sekä sorvausvoimien määrittäminen. Diplomityön teoreettisessa osassa tutustuttiin viilusorvin, erityisesti sen hydraulisten servojärjestelmien rakenteeseen ja toimintaan sekä viilunsorvaukseen. Teräpenkin syötön servojärjestelmää tutkittiin teoreettisesti johtamalla suljetun piirin siirtofunktiot “asema/käsky” ja “virhe/voima” ja tulostamalla niiden taajuusvaste-kuvaajat, joista tutkittiin parametrien vaikutuksia järjestelmän toimintaan. Tulokset vahvistettiin simuloimalla. Todettiin nykyisen järjestelmän värähtelyongelmien johtuvan pääasiassa hydrauliöljyn joustosta sylinterissä. Parannuksina ehdotettiin suurempaa sylinterin halkaisijaa ja viskoosikitkakertoimen suurentamista. Diplomityön kokeellisessa osassa mitattiin viilusorvin servojärjestelmien toimilaitteissa esiintyviä voimia ja niiden perusteella laskettiin varsinaiset sorvausvoimat. Lisäksi tutkittiin teräpenkin syötön ja muiden servojärjestelmien asemointitarkkuutta sorvauksen aikana. Mittauksia varten diplomityössä suunniteltiin ja hankittiin kannettava mittausjärjestelmä.

Toimitusketjun mallinnuksen tarpeet ja rakenne LOCOMOTIVE projekstissa

Työn tavoitteena oli kuvata ja priorisoida toimitusketjun dynaamisen mallinnustyökalun vaatimukset, sekä muodostaa tämän pohjalta ohjelmistokehitystä tukeva oliomalli. Vaatimuksia selvitettiin teoreettisen tarkastelun, aiemmin toteutettujen kyselytutkimusten sekä viiden pilottitapauksen avulla. Toimitusketjun hallinta ei ole pelkästään materiaalivirtojen vaan myös näihin liittyvän informaation hallintaa. Holististen toimitusketjuongelmien mallintaminen edellyttää siis informaatiovirtojen ja niitä saatelevien ohjausmekanisemien mallintamista. Markkinoilla on selkeästi tilaa tukijärjestelmille, jotka mahdollistaisivat multidimensionaalisten - tuotto, aika, palvelu - toimitusketjuongelmien tarkastelun. Systeemidynamiikan teorian mukaisesti oliomallin lähtökohdaksi valittiin tärkeimpien takaisinkytkentäsilmukkojen mallinnus. Takaisinkytkentäsilmukoiden avulla kyetään mallintamaan kompleksisia systeemejä ajan suhteen. Mallinnetut toimitusketjujen takaisinkytkentäsilmukkat ovat operaatio-, ohjaus-, kysyntä- ja strategiasilmukka. Toimitusketjun ohjausmekanismien, sekä systeemidynamiikan perusteiden pohjalta mallinnustyökalun vaatimuksista muodostettiin oliomalli. Muodostettu oliomalli on Locomotiven - toimitusketjun mallinnustyökalun - perusta.

Studies on Neuromuscular Blocking Agents and Their Antagonists During Anaesthesia

Neuromuscular blocking agents (NMBAs) are widely used in clinical anaesthesia and emergency medicine. Main objectives are to facilitate endotracheal intubation and to allow surgery by reducing muscle tone and eliminating sudden movements, which may otherwise lead to trauma and complications. The most commonly used NMBAs are non-depolarizing agents with a medium duration of action, such as rocuronium and cisatracurium. They bind to the acetylcholine receptors in the neuromuscular junction, thus inhibiting the depolarization of the postsynaptic (muscular) membrane, which is a prerequisite for muscle contraction to take place. Previously, it has been assumed that nitrous oxide (N2O), which is commonly used in combination with volatile or intravenous anaesthetics during general anaesthesia, has no effect on NMBAs. Several studies have since claimed that N2O in fact does increase the effect of NMBAs when using bolus administration of the relaxant. The effect of N2O on the infusion requirements of two NMBAs (rocuronium and cisatracurium) with completely different molecular structure and pharmacological properties was assessed. A closed-loop feedback controlled infusion of NMBA with duration of at least 90 minutes at a 90% level of neuromuscular block was used. All patients received total intravenous anaesthesia (TIVA) with propofol and remifentanil. In both studies the study group (n=35) received N2O/Oxygen and the control group (n=35) Air/Oxygen. There were no significant differences in the mean steady state infusion requirements of NMBA (rocuronium in Study I; cisatracurium in Study II) between the groups in either study. In Study III the duration of the unsafe period of recovery after reversal of rocuronium-induced neuromuscular block by using neostigmine or sugammadex as a reversal agent was analyzed. The unsafe period of recovery was defined as the time elapsed from the moment of no clinical (visual) fade in the train-of-four (TOF) sequence until an objectively measured TOF-ratio of 0.90 was achieved. The duration of these periods were 10.3 ± 5.5 and 0.3 ± 0.3 min after neostigmine and sugammadex, respectively (P < 0.001). Study IV investigated the possible effect of reversal of a rocuronium NMB by sugammadex on depth of anaesthesia as indicated by the bispectral index and entropy levels in thirty patients. Sugammadex did not affect the level of anaesthesia as determined by EEG-derived indices of anaesthetic depth such as the bispectral index and entropy.