Freezing Point Depressions of Dilute Solutions of Alkali Metal Chlorides and Bromides

Freezing point depressions (¿Tf) of dilute solutions of several alkali metal chlorides and bromides were calculated by means of the best activity coefficient equations. In the calculations, Hückel, Hamer and Pitzer equationswere used for activity coefficients. The experimental ¿Tf values available in the literature for dilute LiCl, NaCl and KBr solutions can be predicted within experimental error by the Hückel equations used. The experimental ¿Tf values for dilute LiCl and KBr solutions can also be accurately calculated by corresponding Pitzer equations and those for dilute NaCl solutions by the Hamer equation for this salt. Neither Hamer nor Pitzer equations predict accurately the freezing points reported in the literature for LiBr and NaBr solutions. The ¿Tf values available for dilute solutions of RbCl, CsCl or CsBr are not known at the moment accurately because the existing data for these solutions are not precise. The freezing point depressions are tabulated in the present study for LiCl, NaCl and KBr solutions at several rounded molalities. The ¿Tf values in this table can be highly recommended. The activity coefficient equations used in the calculation of these values have been tested with almost allhigh-precision electrochemical data measured at 298.15 K.

Pitkäketjuisten keteenien valmistusreaktiot ja kinetiikka.

Tämän diplomityön tarkoituksena oli tutkia pitkäketjuisten rasvahappokloridien ja alkyyliketeenidimeerien (AKD) valmistusreaktioiden kinetiikkaa. Työn tavoitteena oli saada mittaustuloksia, joiden perusteella voitaisiin kehittää reaktioille kineettinen kineettinen malli ja suorittaa valmistusprosessien alustava optimointi. Teoreettisessa osassa on selvitetty rasvahappokloridien ja alkyyliketeenidimeerien (AKD) eri valmistustapoja. Lisäksi on perehdytty tarkemmin rasvahappokloridien dehydrohalogenointireaktioiden reaktiomekanismeihin ja valmistusprosessin problematiikkaan. Kokeellisessa osassa tutkittiin rasvahappokloridien valmistusta klooraamalla öljyhappoa 30 mol-% fosforitrikloridiylimäärällä lämpötiloissa 45, 50 ja 55OC. Alkyyliketeenidimeerien valmistusta tutkittiin dehydrohalogenoimalla palmitiini- ja öljyhappokloridia 0-30 mol-% trietyyliamiiniylimäärällä inertissä liuottimessa, lämpötiloissa 45 ja 50OC. Reaktiot toteutettiin puolipanosreaktiona, joissa reaktioastiassa olevaan reagenssin ja liuottimen seokseen lisättiin lähtöaine tasaisena massavirtana. Reaktioiden etenemistä seurattiin FT-IR- ja GC-analyysien avulla. Kalorimetrisilla kokeilla tutkittiin öljyhappokloridin dimeroitumisreaktion reaktiolämmön muodostumista ja UV-VIS-analyyseillä seurattiin öljyhappokloridin vanhenemista. Öljyhappokloridin valmistusreaktiolle saatiin hyvä kineettinen malli. Kineettisen mallin puutteena voidaan pitää sitä, ettei kokeissa saatu tietoa mahdollisten sivutuotteiden muodostumisesta. Sovitusohjelmalla saatiin sovitettua estimaatit reaktionopeusvakioille lämpötiloissa 45, 50 ja 55OC. Happokloridien dimeroitumisreaktioiden kineettisen mallin sopivuudelle saatiin suhteellisen hyvä kuva Kuten öljyhappokloridin tapauksessa, myöskään AKD:n valmistusreaktioissa syntynyt sivutuotteita, joten niiden osuutta oletettuun kineettiseen malliin ei tunneta. Sovitusohjelmalla saatiin sovitettua estimaatit reaktionopeusvakioille lämpötiloissa 45 ja 50OC.

Uuttoprosessin suunnittelu

Teknologian kehitys ja prosessien tiukempi valvonta ovat alentaneet selluteollisuuden häviöitä tehden prosesseista suljetumpia. Valitettavasti nämä edistysaskeleet teknologiassa ovat lisänneet prosessiin kuulumattomien yhdisteiden määrää kemikaalien talteenottokierrossa. Näistä kemikaaleista haitallisimpia ovat kloridi- ja kaliumyhdisteet, jotka tulevat prosessiin raaka-aineiden ja prosessikemikaalien mukana. Kloridi ja kalium muodostavat emäksisissä liuoksissa epäorgaanisia liukoisia yhdisteitä, jotka rikastuvat lipeäkiertoon. Soodakattilassa kloridien läsnäolo alentaa tuhkan sulamislämpötilaa sekä tarttumispistettä, lisää korroosiota ja saostumien muodostumista kattilan pinnalle. Nämä seuraukset voivat vähentää vuosituotantoa ja nostaa korjauskustannuksia. Kaliumin ja kloridin rikastumista talteenottokiertoon voidaan estää poistamalla ne prosessista. Prosessiin kuulumattomat yhdisteet tulisi poistaa talteenottoprosessista ja säilyttää samalla korkea kemikaalien talteenottoprosentti. Koska kaliumin ja kloridin rikastumiskertoimet soodakattilan tuhkassa ovat korkeita, on tuhkan käsittely tehokasta. Kloridin ja kaliumin poistoon on kehitetty menetelmiä, joilla voidaan vähentää hyödyllisten kemikaalien häviöitä. Näitä menetelmiä ovat uutto, ioninvaihto, elektrodialyysi, jäähdytyskiteytys ja haihdutuskiteytys. Menetelmissä tuhka jaetaan kloridi- ja kaliumpitoiseen osaan ja natriumsulfaattipitoiseen osaan. Kloridi ja kalium poistetaan prosessista ja loput palautetaan lipeäkiertoon. Kloridin ja kaliumin poistoa tuhkasta tutkittiin uuttamalla tuhkaa vedellä. Parhaissa käyttöolosuhteissa natriumsulfaatin liukoisuus veteen on huomattavasti alhaisempi kuin kaliumkloridin liukoisuus veteen. Optimaalinen uuttolämpötila ja tuhka-vesisuhde määritettiin siten, että kloridi- ja kaliumpitoisuudet suodoksessa olivat mahdollisimman korkeat sekä natriumin ja muiden anioneiden pitoisuudet suodoksessa mahdollisimman alhaiset. Saatuja tuloksia käytettiin jatkuvatoimisen uuttoprosessin suunnittelussa.

Corrosion behaviour of boiler tube materials during combustion of fuels containing Zn and Pb

Många förbränningsanläggningar som bränner utmanande bränslen såsom restfraktioner och avfall råkar ut för problem med ökad korrosion på överhettare och/eller vattenväggar pga. komponenter i bränslena som är korrosiva. För att minimera problemen i avfallseldade pannor hålls ångparametrarna på en relativt låg nivå, vilket drastiskt minskar energiproduktionen. Beläggningarna i avfallseldade pannor består till största delen av element som är förknippade med högtemperaturkorrosion: Cl, S, alkalimetaller, främst K och Na, och tungmetaller som Pb och Zn, och det finns också indikationer av Br-förekomst. Det låga ångtrycket i avfallseldade pannor påverkar också stålrörens temperatur i pannväggarna i eldstaden. I dagens läge hålls temperaturen normalt vid 300-400 °C. Alkalikloridorsakad (KCl, NaCl) högtemperaturkorrosion har inte rapporterats vara relevant vid såpass låga temperaturer, men närvaro av Zn- och Pb-komponenter i beläggningarna har påvisats förorsaka ökad korrosion redan vid 300-400 °C. Vid förbränning kan Zn och Pb reagera med S och Cl och bilda klorider och sulfater i rökgaserna. Dessa tungmetallföreningar är speciellt problematiska pga. de bildar lågsmältande saltblandningar. Dessa lågsmältande gasformiga eller fasta föreningar följer rökgasen och kan sedan fastna eller kondensera på kallare ytor på pannväggar eller överhettare för att sedan bilda aggressiva beläggningar. Tungmetallrika (Pb, Zn) klorider och sulfater ökar risken för korrosion, och effekten förstärks ytterligare vid närvaro av smälta. Motivet med den här studien var att få en bättre insikt i högtemperaturkorrosion förorsakad av Zn och Pb, samt att undersöka och prediktera beteendet och motståndskraften hos några stålkvaliteter som används i överhettare och pannväggar i tungmetallrika förhållanden och höga materialtemperaturer. Omfattande laboratorie-, småskale- och fullskaletest utfördes. Resultaten kan direkt utnyttjas i praktiska applikationer, t.ex. vid materialval, eller vid utveckling av korrosionsmotverkande verktyg för att hitta initierande faktorer och förstå deras effekt på högtemperaturkorrosion.

Methyl and ethyl chloride synthesis in microreactors

Methyl chloride is an important chemical intermediate with a variety of applications. It is produced today in large units and shipped to the endusers. Most of the derived products are harmless, as silicones, butyl rubber and methyl cellulose. However, methyl chloride is highly toxic and flammable. On-site production in the required quantities is desirable to reduce the risks involved in transportation and storage. Ethyl chloride is a smaller-scale chemical intermediate that is mainly used in the production of cellulose derivatives. Thus, the combination of onsite production of methyl and ethyl chloride is attractive for the cellulose processing industry, e.g. current and future biorefineries. Both alkyl chlorides can be produced by hydrochlorination of the corresponding alcohol, ethanol or methanol. Microreactors are attractive for the on-site production as the reactions are very fast and involve toxic chemicals. In microreactors, the diffusion limitations can be suppressed and the process safety can be improved. The modular setup of microreactors is flexible to adjust the production capacity as needed. Although methyl and ethyl chloride are important chemical intermediates, the literature available on potential catalysts and reaction kinetics is limited. Thus the thesis includes an extensive catalyst screening and characterization, along with kinetic studies and engineering the hydrochlorination process in microreactors. A range of zeolite and alumina based catalysts, neat and impregnated with ZnCl2, were screened for the methanol hydrochlorination. The influence of zinc loading, support, zinc precursor and pH was investigated. The catalysts were characterized with FTIR, TEM, XPS, nitrogen physisorption, XRD and EDX to identify the relationship between the catalyst characteristics and the activity and selectivity in the methyl chloride synthesis. The acidic properties of the catalyst were strongly influenced upon the ZnCl2 modification. In both cases, alumina and zeolite supports, zinc reacted to a certain amount with specific surface sites, which resulted in a decrease of strong and medium Brønsted and Lewis acid sites and the formation of zinc-based weak Lewis acid sites. The latter are highly active and selective in methanol hydrochlorination. Along with the molecular zinc sites, bulk zinc species are present on the support material. Zinc modified zeolite catalysts exhibited the highest activity also at low temperatures (ca 200 °C), however, showing deactivation with time-onstream. Zn/H-ZSM-5 zeolite catalysts had a higher stability than ZnCl2 modified H-Beta and they could be regenerated by burning the coke in air at 400 °C. Neat alumina and zinc modified alumina catalysts were active and selective at 300 °C and higher temperatures. However, zeolite catalysts can be suitable for methyl chloride synthesis at lower temperatures, i.e. 200 °C. Neat γ-alumina was found to be the most stable catalyst when coated in a microreactor channel and it was thus used as the catalyst for systematic kinetic studies in the microreactor. A binder-free and reproducible catalyst coating technique was developed. The uniformity, thickness and stability of the coatings were extensively characterized by SEM, confocal microscopy and EDX analysis. A stable coating could be obtained by thermally pretreating the microreactor platelets and ball milling the alumina to obtain a small particle size. Slurry aging and slow drying improved the coating uniformity. Methyl chloride synthesis from methanol and hydrochloric acid was performed in an alumina-coated microreactor. Conversions from 4% to 83% were achieved in the investigated temperature range of 280-340 °C. This demonstrated that the reaction is fast enough to be successfully performed in a microreactor system. The performance of the microreactor was compared with a tubular fixed bed reactor. The results obtained with both reactors were comparable, but the microreactor allows a rapid catalytic screening with low consumption of chemicals. As a complete conversion of methanol could not be reached in a single microreactor, a second microreactor was coupled in series. A maximum conversion of 97.6 % and a selectivity of 98.8 % were reached at 340°C, which is close to the calculated values at a thermodynamic equilibrium. A kinetic model based on kinetic experiments and thermodynamic calculations was developed. The model was based on a Langmuir Hinshelwood-type mechanism and a plug flow model for the microreactor. The influence of the reactant adsorption on the catalyst surface was investigated by performing transient experiments and comparing different kinetic models. The obtained activation energy for methyl chloride was ca. two fold higher than the previously published, indicating diffusion limitations in the previous studies. A detailed modeling of the diffusion in the porous catalyst layer revealed that severe diffusion limitations occur starting from catalyst coating thicknesses of 50 μm. At a catalyst coating thickness of ca 15 μm as in the microreactor, the conditions of intrinsic kinetics prevail. Ethanol hydrochlorination was performed successfully in the microreactor system. The reaction temperature was 240-340°C. An almost complete conversion of ethanol was achieved at 340°C. The product distribution was broader than for methanol hydrochlorination. Ethylene, diethyl ether and acetaldehyde were detected as by-products, ethylene being the most dominant by-product. A kinetic model including a thorough thermodynamic analysis was developed and the influence of adsorbed HCl on the reaction rate of ethanol dehydration reactions was demonstrated. The separation of methyl chloride using condensers was investigated. The proposed microreactor-condenser concept enables the production of methyl chloride with a high purity of 99%.

Chemistry of potassium halides and their role in corrosion in biomass and waste firing

Compared to the use of traditional fossil fuels (coal, oil, natural gas), combustion of biomass and waste fuels has several environmental and economic advantages for heat and power generation. However, biomass and waste fuels might contain halogens (Cl, Br, F), alkali metals (Na, K) and heavy metals (Zn, Pb), which may cause harmful emissions and corrosion problems. Hightemperature corrosion occurs typically on furnace waterwalls and superheaters. The corrosion of the boiler tube materials limits the increase of thermal efficiency of steam boilers and leads to costly shutdowns and repairs. In recent years, some concerns have been raised about halogen (Cl, Br, and F)-related hightemperature corrosion in biomass- and waste-fired boilers. Chlorine-related high-temperature corrosion has been studied extensively. The presence of alkali chlorides in the deposits is believed to play a major role in the corrosion observed in biomass and waste fired boilers. However, there is much less information found in literature on the corrosion effect of bromine and fluorine. According to the literature, bromine is only assumed to play a role similar to chlorine; the role of fluorine is even less understood. In this work, a series of bubbling fluidized bed (BFB) bench-scale tests were carried out to characterize the formation and sulfation behaviors of KCl and KBr in BFB combustion conditions. Furthermore, a series of laboratory tests were carried out to investigate the hightemperature corrosion behaviors of three different superheater steels (10CrMo9-10, AISI 347 and Sanicro 28) exposed to potassium halides in ambient air and wet air (containing 30% H2O). The influence of H2O and O2 on the high-temperature corrosion of steels both with and without a salt (KCl) in three gas atmospheres (2% H2O-30% O2-N2, 2% H2O-2% O2-N2 and 30% H2O-2% O2-N2) was also studied. From the bench-scale BFB combustion tests, it was found that HBr has a clearly higher affinity for the available K forming KBr than HCl forming KCl. The tests also indicated that KCl has a higher tendency for sulfation than KBr. From the laboratory corrosion tests in ambient air (also called “dry air” in Paper III and Paper IV), it was found that at relatively low temperatures (≤ 550 °C) the corrosivity of KBr and KF are similar to KCl. At 600 °C, KF showed much stronger corrosivity than KBr and KCl, especially for 10CrMo9-10 and AISI 347. When exposed to KBr or KF, 10CrMo9-10 was durable at least up to 450 °C, while AISI 347 and Sanicro 28 were durable at least up to 550 °C. From the laboratory corrosion tests in wet air (30% H2O), no obvious effect of water vapor was detected at 450 °C. At 550 °C, the influence of water vapor became significant in some cases, but the trend was not consistent. At 550 °C, after exposure with KBr, 10CrMo9-10 suffered from extreme corrosion; after exposure with KF and KCl, the corrosion was less severe, but still high. At 550 °C, local deep pitting corrosion occurred on AISI 347 and Sanicro 28 after exposure with KF. Some formation of K2CrO4 was observed in the oxide layer. At 550 °C, AISI 347 and Sanicro 28 suffered from low corrosion (oxide layer thickness of < 10 μm) after exposure with KBr and KCl. No formation of K2CrO4 was observed. Internal oxidation occurred in the cases of AISI 347 with KBr and KCl. From the laboratory corrosion tests in three different gas atmospheres (2% H2O-30% O2-N2, 2% H2O-2% O2-N2 and 30% H2O-2% O2-N2), it was found that in tests with no salt, no corrosion occurred on AISI 347 and Sanicro 28 up to 600 °C in both the “O2-rich” (2% H2O-30% O2-N2) and “H2O-rich” (30% H2O-2% O2-N2) gas atmospheres; only 10CrMo9-10 showed increased corrosion with increasing temperature. For 10CrMo9-10 in the “O2-rich” atmosphere, the presence of KCl significantly increased the corrosion compared to the “no salt” cases. For 10CrMo9-10 in the “H2O-rich” atmosphere, the presence or absence of KCl did not show any big influence on corrosion. The formation of K2CrO4 was observed only in the case with the “O2-rich” atmosphere. Considering both the results from the BFB tests and the laboratory corrosion tests, if fuels containing Br were to be combusted, the corrosion damage of superheaters would be expected to be higher than if the fuels contain only Cl. Information generated from these studies can be used to help the boiler manufacturers in selecting materials for the most demanding combustion systems.