Life cycle costs in heating, ventilation and air-conditioning systems with drive

Energy consumption and energy efficiency have become an issue. Energy consumption is rising all over the world and because of that, and the climate change, energy is becoming more and more expensive. Buildings are major consumers of energy, and inside the buildings the major consumers are heating, ventilation and air-conditioning systems. They usually run at constant speed without efficient control. In most cases HVAC equipment is also oversized. Traditionally heating, ventilation and air-conditioning systems have been sized to meet conditions that rarely occur. The theory part in this thesis represents the basics of life cycle costs and calculations for the whole life cycle of a system. It also represents HVAC systems, equipment, systems controls and ways to save energy in these systems. The empirical part of this thesis represents life cycle cost calculations for HVAC systems. With these calculations it is possible to compute costs for the whole life cycle for the wanted variables. Life cycle costs make it possible to compare which variable causes most of the costs from the whole life point of view. Life cycle costs were studied through two real life cases which were focused on two different kinds of HVAC systems. In both of these cases the renovations were already made, so that the comparison between the old and the new, now existing system would be easier. The study indicates that energy can be saved in HVAC systems by using variable speed drive as a control method.

Specific surface charging of latex, clay and mineral oxide particles in aqueous, non-aqueous and mixed solvent systems

En djupare förståelse för växelverkan mellan partiklar i suspensioner är av betydelse för utvecklingen av en mängd olika industriella produkter och processer. Till exempel kan nämnas pigmentbaserade färger och bestrykning av papper. Genom att öka kontrollbarheten kan dessa lättare optimeras för att uppnå förbättrade produktegenskaper och/eller sänkta produktionskostnader. Av stor betydelse är även en förbättrad möjlighet att minska produktens miljöpåverkan. I avhandlingen studerades jonstyrkan och jonspecificiteten inverkan i olika akvatiska suspensioner innehållande olika elektrolyter. De partiklar som avhandlingen omfattade var metalloxider, leror samt latex. Jonstyrkan studerades från låga (c <10-3M) till och med höga (c> 10-1M) elektrolytkoncentrationer. Vid koncentrationer under 0.1 M var partikelladdningen styrd av pH och jonstyrkan. Vid högre elektrolytkoncentrationer påverkade även jonspecificiteten partikelladdningen. Jonspecificiteten arrangerades i fenomenologiska serier funna i litteraturen samt med Born modellen definierad i termodynamiken. Överraskande höga absoluta zeta-potential värden erhölls vid höga elektrolytkoncentrationer vilket visar att den elektrostatiska repulsionen har betydelse även vid dessa förhållanden. Vidare studerades titanoxidsuspensioners egenskaper i akvatiska, icke-akvatiska och blandade lösningssystem under varierande koncentration av oxal- och fosfatsyra. Vid lågt vatteninnehåll studerades även suspensioner med svavelsyra. Konduktiviteten i suspensioner med lågt vatteninnehåll ökade med tillsatt oxal- eller fosforsyra vilket är en omvänd effekt jämfört med svavelsyra eller akvatiska suspensioner. Den omvända effekten skiftade gradvis tillbaka med ökad vatteninnehåll. En analys av suspensionernas adsorption i höga etanolkoncentrationer gjordes med konduktiviteten, pH och zeta-potentialen. Viskositet studerades och applicerades framgångsrikt i viskositet/ytladdningsmodeller utvecklade för akvatiska suspensioner.

Business intelligence viewpoint on managerial decision-making : Ill-structured problems and decision support systems

Vaikka liiketoimintatiedon hallintaa sekä johdon päätöksentekoa on tutkittu laajasti, näiden kahden käsitteen yhteisvaikutuksesta on olemassa hyvin rajallinen määrä tutkimustietoa. Tulevaisuudessa aiheen tärkeys korostuu, sillä olemassa olevan datan määrä kasvaa jatkuvasti. Yritykset tarvitsevat jatkossa yhä enemmän kyvykkyyksiä sekä resursseja, jotta sekä strukturoitua että strukturoimatonta tietoa voidaan hyödyntää lähteestä riippumatta. Nykyiset Business Intelligence -ratkaisut mahdollistavat tehokkaan liiketoimintatiedon hallinnan osana johdon päätöksentekoa. Aiemman kirjallisuuden pohjalta, tutkimuksen empiirinen osuus tunnistaa liiketoimintatiedon hyödyntämiseen liittyviä tekijöitä, jotka joko tukevat tai rajoittavat johdon päätöksentekoprosessia. Tutkimuksen teoreettinen osuus johdattaa lukijan tutkimusaiheeseen kirjallisuuskatsauksen avulla. Keskeisimmät tutkimukseen liittyvät käsitteet, kuten Business Intelligence ja johdon päätöksenteko, esitetään relevantin kirjallisuuden avulla – tämän lisäksi myös dataan liittyvät käsitteet analysoidaan tarkasti. Tutkimuksen empiirinen osuus rakentuu tutkimusteorian pohjalta. Tutkimuksen empiirisessä osuudessa paneudutaan tutkimusteemoihin käytännön esimerkein: kolmen tapaustutkimuksen avulla tutkitaan sekä kuvataan toisistaan irrallisia tapauksia. Jokainen tapaus kuvataan sekä analysoidaan teoriaan perustuvien väitteiden avulla – nämä väitteet ovat perusedellytyksiä menestyksekkäälle liiketoimintatiedon hyödyntämiseen perustuvalle päätöksenteolle. Tapaustutkimusten avulla alkuperäistä tutkimusongelmaa voidaan analysoida tarkasti huomioiden jo olemassa oleva tutkimustieto. Analyysin tulosten avulla myös yksittäisiä rajoitteita sekä mahdollistavia tekijöitä voidaan analysoida. Tulokset osoittavat, että rajoitteilla on vahvasti negatiivinen vaikutus päätöksentekoprosessin onnistumiseen. Toisaalta yritysjohto on tietoinen liiketoimintatiedon hallintaan liittyvistä positiivisista seurauksista, vaikka kaikkia mahdollisuuksia ei olisikaan hyödynnetty. Tutkimuksen merkittävin tulos esittelee viitekehyksen, jonka puitteissa johdon päätöksentekoprosesseja voidaan arvioida sekä analysoida. Despite the fact that the literature on Business Intelligence and managerial decision-making is extensive, relatively little effort has been made to research the relationship between them. This particular field of study has become important since the amount of data in the world is growing every second. Companies require capabilities and resources in order to utilize structured data and unstructured data from internal and external data sources. However, the present Business Intelligence technologies enable managers to utilize data effectively in decision-making. Based on the prior literature, the empirical part of the thesis identifies the enablers and constraints in computer-aided managerial decision-making process. In this thesis, the theoretical part provides a preliminary understanding about the research area through a literature review. The key concepts such as Business Intelligence and managerial decision-making are explored by reviewing the relevant literature. Additionally, different data sources as well as data forms are analyzed in further detail. All key concepts are taken into account when the empirical part is carried out. The empirical part obtains an understanding of the real world situation when it comes to the themes that were covered in the theoretical part. Three selected case companies are analyzed through those statements, which are considered as critical prerequisites for successful computer-aided managerial decision-making. The case study analysis, which is a part of the empirical part, enables the researcher to examine the relationship between Business Intelligence and managerial decision-making. Based on the findings of the case study analysis, the researcher identifies the enablers and constraints through the case study interviews. The findings indicate that the constraints have a highly negative influence on the decision-making process. In addition, the managers are aware of the positive implications that Business Intelligence has for decision-making, but all possibilities are not yet utilized. As a main result of this study, a data-driven framework for managerial decision-making is introduced. This framework can be used when the managerial decision-making processes are evaluated and analyzed.

Preparing for CRIS: Challenges and Opportunities for Systems Integration at Finnish Universities

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Analytic evaluation of three-phase short circuit demagnetization and hysteresis loss risk in rotor-surface-magnet Permanent-Magnet Synchronous Machines

Permanent magnet synchronous machines (PMSM) have become widely used in applications because of high efficiency compared to synchronous machines with exciting winding or to induction motors. This feature of PMSM is achieved through the using the permanent magnets (PM) as the main excitation source. The magnetic properties of the PM have significant influence on all the PMSM characteristics. Recent observations of the PM material properties when used in rotating machines revealed that in all PMSMs the magnets do not necessarily operate in the second quadrant of the demagnetization curve which makes the magnets prone to hysteresis losses. Moreover, still no good analytical approach has not been derived for the magnetic flux density distribution along the PM during the different short circuits faults. The main task of this thesis is to derive simple analytical tool which can predict magnetic flux density distribution along the rotor-surface mounted PM in two cases: during normal operating mode and in the worst moment of time from the PM’s point of view of the three phase symmetrical short circuit. The surface mounted PMSMs were selected because of their prevalence and relatively simple construction. The proposed model is based on the combination of two theories: the theory of the magnetic circuit and space vector theory. The comparison of the results in case of the normal operating mode obtained from finite element software with the results calculated with the proposed model shows good accuracy of model in the parts of the PM which are most of all prone to hysteresis losses. The comparison of the results for three phase symmetrical short circuit revealed significant inaccuracy of the proposed model compared with results from finite element software. The analysis of the inaccuracy reasons was provided. The impact on the model of the Carter factor theory and assumption that air have permeability of the PM were analyzed. The propositions for the further model development are presented.

Web user interface architecture for advanced planning and scheduling systems Case: Nokia Demand / Supply Planning Applications

In modem hitec industry Advanced Planning and Scheduling (APS) systems provide the basis for e-business solutions towards the suppliers and the customers. One objective of this thesis was to clarify the modem supply chain management with the APS systems and especially concentrate on the area of Collaborative Planning. In order Advanced Planning and Scheduling systems to be complete and usable, user interfaces are needed. Current Visual Basic user interfaces have faced many complaints and arguments from the users as well as from the development team. This thesis is trying to analyze the reasons and causes for the encountered problems and also provide ways to overcome them. The decision has been made to build the new user interfaces to be Web-enabled. Therefore another objective of this thesis was to research and find suitable technologies for building the Web-based user interfaces for Advanced Planning and Scheduling Systems in Nokia Demand/Supply Planning business area. Comparison between the most suitable technologies is made. Usability issues of Web-enabled user interfaces are also covered. The empirical part of the thesis includes design and implementation of a Web-based user interface with the chosen technology for a particular APS module that enables Collaborative Planning with suppliers.

Induction Motor Drive Energy Efficiency - Simulation and Analysis

A coupled system simulator, based on analytical circuit equations and a finite element method (FEM) model of the motor has been developed and it is used to analyse a frequency-converterfed industrial squirrel-cage induction motor. Two control systems that emulate the behaviour of commercial direct-torque-controlled (DTC) and vector-controlled industrial frequency converters have been studied, implemented in the simulation software and verified by extensive laboratory tests. Numerous factors that affect the operation of a variable speed drive (VSD) and its energy efficiency have been investigated, and their significance in the simulation of the VSD results has been studied. The dependency of the frequency converter, induction motor and system losses on the switching frequency is investigated by simulations and measurements at different speeds for both the vector control and the DTC. Intensive laboratory measurements have been carried out to verify the simulation results.

An Infant with Food Allergy and Eczema in the Family – The Mental and Economic Burden of Caring

Allergic diseases including food allergy and eczema in an infant in combination with the everyday activities of caring for a family will pose challenges to parents. Only fragments of these challenges are revealed to health care professionals. Families have varying mental, social and economic resources to help them care for an allergic infant, and all such resources are important in determining how families succeed in meeting these challenges and the quality of the infant’s care. This study evaluated the whole burden to the family caused by an infant's allergic disease during the first 24 months of life. As the primary caregiver during this period is usually the mother, her perspective was considered important. Ecocultural theory, which considers families as capable of modifying the positive and negative forces facing them, was taken as the frame of reference. Data were collected as part of an ongoing prospective mother-infant study, and the methods included severity scoring of atopic dermatitis, dietary records, health-related quality of life measurements and assessments of the use of health care services and medications for treating the infant’s eczema, food allergy and asthma. Interviews with mothers were analysed by deductive content analysis on the basis of ecocultural theory and the family empowerment model. The theme “Living an ordinary family life” guided the organization of family activities essential for treating the infant's food allergy and eczema. These activities were sources of both strain and support for the mothers, the allergy-related supporting factors being the mother’s own knowledge of the allergy, hopes for an improvement in the infant’s condition, social support and work. An infant’s food allergy at the age of one year caused considerable strain for the mother in cases where the introduction of new foods into the child’s diet was delayed. This delay was still causing the mother additional strain when the child was 24 months of age. The infants waking at night at the ages of 12 and 24 months because of itching related to eczema caused strain for the mothers. The infants’ health-related quality of life was impaired at ages of 6 and 12 months compared with healthy infants. The principal reasons for impairments were itching, scratching and sleep disturbances at 6 and 12 months and treatment difficulties at 6 months. Problems with getting to sleep were reported at all stages irrespective of eczema and were also present in healthy infants. The economic impact of the treatment of allergic diseases on families during the first 24 months was 131 EUR (2006 value) in cases of eczema and 525 EUR in cases of food allergy. From the societal perspective, the costs of food allergy were a median of 3183 EUR (range 628–11 560 EUR) and of eczema a median of 275 EUR (range 94–1306 EUR). These large variations in costs in food allergy and eczema indicate that disease varies greatly . In conclusion, food allergy and eczema cause extra activities and costs to families which arrange these disease-related activities in such a way that they support the leading family theme “Living an ordinary family life”. Health care professionals should consider this thematic character of family life and disease-related activities in order to ensure that new treatments are sustainable, meaningful and tailored to daily activities. In addition, those mothers who are experiencing difficulties with food allergic infants or infants with eczema should be recognized early and provided with individual encouragement and support from health clinics. In the light of the present results, early detection of symptoms and effective parental guidance can contribute to the well-being and health-related quality of life of the child and family.

Family-based dietary intervention in the STRIP study – influences on diet and diet-related attitudes

The focus of this dissertation was to investigate the effects of family-based dietary intervention during childhood and adolescence. The participants comprised of children and parents who participated in a longitudinal, randomised atherosclerosis prevention trial (STRIP study). The intervention families (n=540) took part in a dietary intervention since the child’s age of 8- months. The control group (n=522) did not receive any tailored dietary intervention. The main focus of the intervention was to improve the quality of dietary fat. The diet of children and parents was evaluated by daily food records and dietrelated attitudes by a questionnaire. The dietary intervention influenced, favourably, the dietary fat quality in children and parents. Fat quality improved mainly by the decrease of saturated fat intake. Some minor effects of the intervention were also observed in children’s fruit and vegetable (F&V) consumption although the F&V consumption was very low. The intervention increased parental interest in healthy eating, but there was no difference in interest in natural products or in attitudes towards hedonic eating attitudes between the intervention and control parents. Parents’ interest in healthy eating associated with parents’ and children’s high fruit and vegetable consumption but not with their fat quality ratio. On the other hand, dietary fat quality improved at every level of interest in healthy eating. It seems that the main target of the intervention, the dietary fat quality of the children, was promoted effectively. In the future, more emphasis should be given on increasing unsaturated fat intake and on elevating F&V consumption in children. Children’s diet, especially F&V consumption, associated with diet-related attitudes of the parents. Therefore, co-operation with parents and family-based premises for working should be capitalized upon when promoting healthy eating in children and adolescents.

Economic and environmental evaluation of renewable energy systems

The main objective of this thesis is to evaluate the economic and environmental effectiveness of three different renewable energy systems: solar PV, wind energy and biomass energy systems. Financial methods such as Internal Rate of Return (IRR) and Modified Internal Rate of Return (MIRR) were used to evaluate economic competitiveness. Seasonal variability in power generation capability of different renewable systems were also taken into consideration. In order to evaluate the environmental effectiveness of different energy systems, default values in GaBi software were taken by defining the functional unit as 1kWh. The results show that solar PV systems are difficult to justify both in economic as well as environmental grounds. Wind energy performs better in both economic and environmental grounds and has the capability to compete with conventional energy systems. Biomass energy systems exhibit environmental and economic performance at the middle level. In each of these systems, results vary.