The key elements for genetic response in Finnish dairy cattle breeding

Selostus: Perinnöllinen edistyminen suomalaisessa lypsykarjan jalostusohjelmassa

Simulation of Boundary Layers and Heat Transfer in the Entrance Region of Pipes

The study of fluid flow in pipes is one of the main topic of interest for engineers in industries. In this thesis, an effort is made to study the boundary layers formed near the wall of the pipe and how it behaves as a resistance to heat transfer. Before few decades, the scientists used to derive the analytical and empirical results by hand as there were limited means available to solve the complex fluid flow phenomena. Due to the increase in technology, now it has been practically possible to understand and analyze the actual fluid flow in any type of geometry. Several methodologies have been used in the past to analyze the boundary layer equations and to derive the expression for heat transfer. An integral relation approach is used for the analytical solution of the boundary layer equations and is compared with the FLUENT simulations for the laminar case. Law of the wall approach is used to derive the empirical correlation between dimensionless numbers and is then compared with the results from FLUENT for the turbulent case. In this thesis, different approaches like analytical, empirical and numerical are compared for the same set of fluid flow equations.

Dynamic Model of a Small Once-Through Boiler

In this study, a model for the unsteady dynamic behaviour of a once-through counter flow boiler that uses an organic working fluid is presented. The boiler is a compact waste-heat boiler without a furnace and it has a preheater, a vaporiser and a superheater. The relative lengths of the boiler parts vary with the operating conditions since they are all parts of a single tube. The present research is a part of a study on the unsteady dynamics of an organic Rankine cycle power plant and it will be a part of a dynamic process model. The boiler model is presented using a selected example case that uses toluene as the process fluid and flue gas from natural gas combustion as the heat source. The dynamic behaviour of the boiler means transition from the steady initial state towards another steady state that corresponds to the changed process conditions. The solution method chosen was to find such a pressure of the process fluid that the mass of the process fluid in the boiler equals the mass calculated using the mass flows into and out of the boiler during a time step, using the finite difference method. A special method of fast calculation of the thermal properties has been used, because most of the calculation time is spent in calculating the fluid properties. The boiler was divided into elements. The values of the thermodynamic properties and mass flows were calculated in the nodes that connect the elements. Dynamic behaviour was limited to the process fluid and tube wall, and the heat source was regarded as to be steady. The elements that connect the preheater to thevaporiser and the vaporiser to the superheater were treated in a special way that takes into account a flexible change from one part to the other. The model consists of the calculation of the steady state initial distribution of the variables in the nodes, and the calculation of these nodal values in a dynamic state. The initial state of the boiler was received from a steady process model that isnot a part of the boiler model. The known boundary values that may vary during the dynamic calculation were the inlet temperature and mass flow rates of both the heat source and the process fluid. A brief examination of the oscillation around a steady state, the so-called Ledinegg instability, was done. This examination showed that the pressure drop in the boiler is a third degree polynomial of the mass flow rate, and the stability criterion is a second degree polynomial of the enthalpy change in the preheater. The numerical examination showed that oscillations did not exist in the example case. The dynamic boiler model was analysed for linear and step changes of the entering fluid temperatures and flow rates.The problem for verifying the correctness of the achieved results was that there was no possibility o compare them with measurements. This is why the only way was to determine whether the obtained results were intuitively reasonable and the results changed logically when the boundary conditions were changed. The numerical stability was checked in a test run in which there was no change in input values. The differences compared with the initial values were so small that the effects of numerical oscillations were negligible. The heat source side tests showed that the model gives results that are logical in the directions of the changes, and the order of magnitude of the timescale of changes is also as expected. The results of the tests on the process fluid side showed that the model gives reasonable results both on the temperature changes that cause small alterations in the process state and on mass flow rate changes causing very great alterations. The test runs showed that the dynamic model has no problems in calculating cases in which temperature of the entering heat source suddenly goes below that of the tube wall or the process fluid.

Corporate Identity and Desired Image Elements as a Basis for Corporate Image Development, Case: Myllykoski Sales

Tutkimuksen päätavoitteena oli auttaa Myllykoski –ryhmää määrittämään, mistä tekijöistä ryhmän uuden myyntiorganisaation, Myllykoski Salesin, tulevaisuuden imagon tulisi koostua. Näin ollen tutkimus pyrki selvittämään Myllykoski –ryhmän yritysidentiteetin nykytilaa ja Myllykoski Salesin toivottuja imagotekijöitä, sekä vertaamaan niiden vastaavuutta. Lisäksi tutkimuksen tavoitteena oli tutkia Myllykoski –ryhmän nykyistä ja toivottua tulevaisuuden imagotilaa. Jotta imagonrakennusprosessi olisi menestyksekäs, rakennettavan imagon ja viestittävien imagotekijöiden tulisi perustua yritysidentiteetin todellisiin tekijöihin. Yritysidentiteetin voidaan määritellä olevan yhtäläinen sisäisten sidosryhmien muodostaman yritysmielikuvan kanssa ja näin ollen nykyinen yritysidentiteetti voidaan paljastaa tutkimalla henkilökunnan mielipiteitä työorganisaatiotaan kohtaan. Näin ollen käsiteltävä tutkimus suoritettiin tekemällä kaksi sähköpostikyselyä, jotka suunnattiin Myllykoski -ryhmän myynti- ja markkinointihenkilökunnalle. Tutkimusten vastausprosentit olivat 71,4 % (johto, 14 lähetettyä kyselyä) ja 51,9 % (muu henkilökunta, 108 lähetettyä kyselyä). Saatuja vastauksia analysoitiin sekä laadullisesti että määrällisesti. Saaduista vastauksista oli selvästi havaittavissa Myllykoski –ryhmän yritysidentiteetin nykytila, nykyinen ja toivottu imagotila, sekä Myllykoski Salesin toivotut imagotekijät. Verrattaessa toivottuja imagotekijöitä ryhmän yritysidentiteettiin havaittiin, että suurin osa halutuista imagotekijöistä vastasi ryhmän identiteetin nykytilan ominaisuuksia ja näin ollen kyseisiä tekijöitä voitaisiin huoletta viestiä rakennettaessa Myllykoski Salesin imagoa. Joidenkin toivottujen imagotekijöiden viestintää tulisi kuitenkin vakavasti harkita, jottei rakennettaisi epärealistista imagoa.

Fusion weld metal solidification:Continuum from weld interface to centerline

We present a brief résumé of the history of solidification research and key factors affecting the solidification of fusion welds. There is a general agreement of the basic solidification theory, albeit differing - even confusing - nomenclatures do exist, and Cases 2 and 3 (the Chalmers' basic boundary conditions for solidification, categorized by Savage as Cases) are variably emphasized. Model Frame, a tool helping to model the continuum of fusion weld solidification from start to end, is proposed. It incorporates the general solidification models, of which the pertinent ones are selected for the actual modeling. The basic models are the main solidification Cases 1…4. These discrete Cases are joined with Sub-Cases: models of Pfann, Flemings and others, bringing needed Sub-Case variables into the model. Model Frame depicts a grain growing from the weld interface to its centerline. Besides modeling, the Model Frame supports education and academic debate. The new mathematical modeling techniques will extend its use into multi-dimensional modeling, introducing new variables and increasing the modeling accuracy. We propose a model: melting/solidification-model (M/S-model) - predicting the solute profile at the start of the solidification of a fusion weld. This Case 3-based Sub-Case takes into account the melting stage, the solute back-diffusion in the solid, and the growth rate acceleration typical to fusion welds. We propose - based on works of Rutter & Chalmers, David & Vitek and our experimental results on copper - that NEGS-EGS-transition is not associated only with cellular-dendritic-transition. Solidification is studied experimentally on pure and doped copper with welding speed range from 0 to 200 cm/min, with one test at 3000 cm/min. Found were only planar and cellular structures, no dendrites - columnar or equiaxed. Cell sub structures: rows of cubic elements we call "cubelettes", "cell-bands" and "micro-cells", as well as an anomalous crack morphology "crack-eye", were detected, as well as microscopic hot crack nucleus we call "grain-lag cracks", caused by a grain slightly lagging behind its neighbors in arrival to the weld centerline. Varestraint test and R-test revealed a change of crack morphologies from centerline cracks to grainand cell boundary cracks with an increasing welding speed. High speed made the cracks invisible to bare eye and hardly detectable with light microscope, while electron microscope often revealed networks of fine micro-cracks.

Loneliness of Older People and Elements of an Intervention for its Alleviation

Ikääntyneiden yksinäisyys ja intervention elementit sen lievittämisessä Ikääntyneiden yksinäisyys on yleistä ja hoitotyöntekijöillä on vähän keinoja sen lievittämiseen. Tutkimus oli kaksiosainen. Ensimmäisen osan tavoitteena oli saada tietoa yksinäisyyden käsitteestä, sen yhteydestä sosiaaliseen eristäytyneisyyteen ja yleiseen turvattomuuden tunteeseen sekä kotona asuvien ikääntyneiden (≥75 v.) yksinäisyyden yleisyydestä ja siihen yhteydessä olevista tekijöistä sekä selvittää ikääntyneiden itsensä kokemia yksinäisyyden syitä. Toisessa osassa tavoitteena oli tunnistaa yksinäisyyden lievittämiseen pyrkivän psykososiaalisen ryhmäkuntoutus (PRK) –intervention elementit sekä kuvata ryhmiin osallistuneiden kokemuksia interventiosta. Ensimmäisessä osassa tutkimusaineosto kerättiin postikyselyllä, joka lähetettiin eri puolilla Suomea kotona tai palvelutalossa asuville satunnaisotannalla valituille ikääntyneille henkilöille (N=6 786). Vastausprosentti oli 72 % (n=4113). Vastaajien keski-ikä oli 81 vuotta. Tutkimuksen toisessa osassa aineisto koostui PRK intervention ryhmänvetäjien (N=14) kirjoittamista päiväkirjoista, tutkijoiden vapaista muistiinpanoista ryhmätoiminnasta (N=32) sekä ryhmäläisten intervention jälkeen täyttämistä palautekyselystä (n=103). Tulosten mukaan yksinäisyys, sosiaalinen eristäytyneisyys ja yleinen turvattomuuden tunne näyttävät olevan eri asioita. Vastanneista 39 % kärsi yksinäisyydestä vähintään joskus. Useat demografiset ja terveyteen liittyvät tekijät, psyykkisen hyvinvoinnin ulottuvuudet kuten myös sosiaalisiin suhteisiin kohdistetut odotukset olivat yhteydessä yksinäisyyden kokemiseen. Vanhempien menettäminen lapsuudessa ei ollut yhteydessä yksinäisyyden kokemiseen. Yksinäisyyden kokemuksiin oli useita syitä. Aineistosta tunnistettiin elementtejä, joiden katsottiin olevan tärkeitä yksinäisyyden lievittämiseen pyrkivän PRK-intervention toteutuksessa. Nämä voitiin jakaa ennalta määriteltyihin elementteihin, ryhmäläisten sisäisiin ja välisiin suosiollisiin prosesseihin sekä välittäviin tekijöihin. Ennalta määritellyt elementit liittyivät ryhmäläisiin, ryhmän vetäjiin ja ryhmätoimintaan. Ryhmäläiset kokivat ryhmät erittäin merkityksellisiksi, ja 95 % koki, että yksinäisyys oli lievittynyt ryhmän aikana. Ikääntyneiden henkilöiden yksinäisyys on haaste hoitotyön tekijöille. Tutkimuksessa kuvattu PRK-interventio auttaa hoitajia tunnistamaan ikääntyneiden yksinäisyyden lievittämiseen liittyviä elementtejä.

Development of beam and plate finite elements based on the absolute nodal coordinate formulation

The focus of this dissertation is to develop finite elements based on the absolute nodal coordinate formulation. The absolute nodal coordinate formulation is a nonlinear finite element formulation, which is introduced for special requirements in the field of flexible multibody dynamics. In this formulation, a special definition for the rotation of elements is employed to ensure the formulation will not suffer from singularities due to large rotations. The absolute nodal coordinate formulation can be used for analyzing the dynamics of beam, plate and shell type structures. The improvements of the formulation are mainly concentrated towards the description of transverse shear deformation. Additionally, the formulation is verified by using conventional iso-parametric solid finite element and geometrically exact beam theory. Previous claims about especially high eigenfrequencies are studied by introducing beam elements based on the absolute nodal coordinate formulation in the framework of the large rotation vector approach. Additionally, the same high eigenfrequency problem is studied by using constraints for transverse deformation. It was determined that the improvements for shear deformation in the transverse direction lead to clear improvements in computational efficiency. This was especially true when comparative stress must be defined, for example when using elasto-plastic material. Furthermore, the developed plate element can be used to avoid certain numerical problems, such as shear and curvature lockings. In addition, it was shown that when compared to conventional solid elements, or elements based on nonlinear beam theory, elements based on the absolute nodal coordinate formulation do not lead to an especially stiff system for the equations of motion.

Measuring Brand Equity and Analyzing Its Relationship with Key Marketing Mix Elements

The aim of this paper is to analyze the effect of price and advertising on brand equity. The dimensionality of brand equity is thoroughly examined, and the effect price, price deals, perceived advertising spending and advertising appeal have on the dimensions of brand equity are analyzed using multiple regression analysis as well as other supporting analyses. Price and advertising are found to be of great importance to brand equity. Arguably the most influential finding is the strong positive effect low prices – an integral brand element – have on the case company brand equity, even though a negative effect was hypothesized based on prior research. The results also support separating advertising appeal from perceived advertising spending, as well as linking service quality as part of the overall perceived quality in the context of service-intensive firms.

Boundary identification in the domain of a parabolic partial differential equation

Bakgrunden och inspirationen till föreliggande studie är tidigare forskning i tillämpningar på randidentifiering i metallindustrin. Effektiv randidentifiering möjliggör mindre säkerhetsmarginaler och längre serviceintervall för apparaturen i industriella högtemperaturprocesser, utan ökad risk för materielhaverier. I idealfallet vore en metod för randidentifiering baserad på uppföljning av någon indirekt variabel som kan mätas rutinmässigt eller till en ringa kostnad. En dylik variabel för smältugnar är temperaturen i olika positioner i väggen. Denna kan utnyttjas som insignal till en randidentifieringsmetod för att övervaka ugnens väggtjocklek. Vi ger en bakgrund och motivering till valet av den geometriskt endimensionella dynamiska modellen för randidentifiering, som diskuteras i arbetets senare del, framom en flerdimensionell geometrisk beskrivning. I de aktuella industriella tillämpningarna är dynamiken samt fördelarna med en enkel modellstruktur viktigare än exakt geometrisk beskrivning. Lösningsmetoder för den s.k. sidledes värmeledningsekvationen har många saker gemensamt med randidentifiering. Därför studerar vi egenskaper hos lösningarna till denna ekvation, inverkan av mätfel och något som brukar kallas förorening av mätbrus, regularisering och allmännare följder av icke-välställdheten hos sidledes värmeledningsekvationen. Vi studerar en uppsättning av tre olika metoder för randidentifiering, av vilka de två första är utvecklade från en strikt matematisk och den tredje från en mera tillämpad utgångspunkt. Metoderna har olika egenskaper med specifika fördelar och nackdelar. De rent matematiskt baserade metoderna karakteriseras av god noggrannhet och låg numerisk kostnad, dock till priset av låg flexibilitet i formuleringen av den modellbeskrivande partiella differentialekvationen. Den tredje, mera tillämpade, metoden kännetecknas av en sämre noggrannhet förorsakad av en högre grad av icke-välställdhet hos den mera flexibla modellen. För denna gjordes även en ansats till feluppskattning, som senare kunde observeras överensstämma med praktiska beräkningar med metoden. Studien kan anses vara en god startpunkt och matematisk bas för utveckling av industriella tillämpningar av randidentifiering, speciellt mot hantering av olinjära och diskontinuerliga materialegenskaper och plötsliga förändringar orsakade av “nedfallande” väggmaterial. Med de behandlade metoderna förefaller det möjligt att uppnå en robust, snabb och tillräckligt noggrann metod av begränsad komplexitet för randidentifiering.

Motivational Influences on Transfer: Dimensions and Boundary Conditions

The focus of this dissertation is the motivational influences on transfer in higher education and professional training contexts. To estimate these motivational influences, the dissertation includes seven individual studies that are structured in two parts. Part I, Dimensions, aims at identifying the dimensionality of motivation to transfer and its structural relations with training-related antecedents and outcomes. Part II, Boundary Conditions, aims at testing the predictive validity of motivation theories used in contemporary training research under different study conditions. Data in this dissertation was gathered from multi-item questionnaires, which were analyzed differently in Part I and Part II. Studies in Part I employed exploratory and confirmatory factor analysis, structural equation modeling, partial least squares (PLS) path modeling, and mediation analysis. Studies in Part II used artifact distribution meta-analysis, (nested) subgroup analysis, and weighted least squares (WLS) multiple regression. Results demonstrate that motivation to transfer can be conceptualized as a three-dimensional construct, including autonomous motivation to transfer, controlled motivation to transfer, and intention to transfer, given a theoretical framework informed by expectancy theory, self-determination theory, and the theory of planned behavior. Results also demonstrate that a range of boundary conditions moderates motivational influences on transfer. To test the predictive validity of expectancy theory, social cognitive theory, and the theory of goal orientations under different study settings, a total of 17 boundary conditions were meta-analyzed, including age; assessment criterion; assessment source; attendance policy; collaboration among trainees; computer support; instruction; instrument used to measure motivation; level of education; publication type; social training context; SS/SMC bias; study setting; survey modality; type of knowledge being trained; use of a control group; and work context. Together, the findings cumulated in this thesis support the basic premise that motivation is centrally important for transfer, but that motivational influences need to be understood from a more differentiated perspective than commonly found in the literature, in order to account for several dimensions and boundary conditions. The results of this dissertation across the seven individual studies are reflected in terms of their implications for theory development and their significance for training evaluation and the design of training environments. Limitations and directions to take in future research are discussed.

Surface chemistry of fibres and vessel elements in chemical and recycled pulps

Den viktigaste råvaran i papperstillverkning är pappersmassa. Massan innehåller (ved)fibrer men också finmaterial och andra typers (ved)celler, så som kärlceller. Hur dessa komponenter beter sig under arkformationen i pappersmaskinen eller hur de bidrar till egenskaperna hos det färdiga pappret avgörs till stor del av massakomponenternas ytkemiska sammansättning, fysiska struktur och mängden joniserbara grupper på ytan. I denna avhandling studerades ytegenskaperna hos fraktionerade kemiska massor och returfibermassor med avancerade analystekniker. Rester av avfärgningskemikalier identifierades på både returfibrer och på kärlceller. Dessa kan påverka arkformationen och arkstyrkan på returfiberpapper. Kärlcellernas cellväggsstruktur visade sig skilja sig från fibrernas. Resultaten kan främja utvecklingen av returfiberprosessen och användningen av kärlcellsrika lövvedsmassor.