Propagation of the Ignition Front against Airflow in Packed Beds of Wood Particles

Combustion of wood is increasing because of the needs of decreasing the emissions of carbon dioxide and the amount of waste going to landfills. Wood based fuels are often scattered on a large area. The transport distances should be short enough to prevent too high costs, and so the size of heating and power plants using wood fuels is often rather small. Combustion technologies of small-size units have to be developed to reach efficient and environmentally friendly energy production. Furnaces that use different packed bed combustion or gasification techniques areoften most economic in small-scale energy production. Ignition front propagation rate affects the stability, heat release rate and emissions of packed bed combustion. Ignition front propagation against airflow in packed beds of wood fuels has been studied. The research has been carried out mainly experimentally. Theoretical aspects have been considered to draw conclusions about the experimental results. The effects of airflow rate, moisture content of the fuel, size, shape and density of particles, and porosity of the bed on the propagation rate of the ignition front have been studied. The experiments were carried out in a pot furnace. The fuels used in the experiments were mainly real wood fuels that are often burned in the production of energy. The fuel types were thin wood chips, saw dust, shavings, wood chips, and pellets with different sizes. Also a few mixturesof the above were tested. Increase in the moisture content of the fuel decreases the propagation rates of the ignition front and makes the range of possible airflow rates narrower because of the energy needed for the evaporation of water and the dilution of volatile gases due to evaporated steam. Increase in the airflow rate increases the ignition rate until a maximum rate of propagation is reached after which it decreases. The maximum flame propagation rate is not always reached in stoichiometric combustion conditions. Increase in particle size and density transfers the optimum airflow rate towards fuel lean conditions. Mixing of small and large particles is often advantageous, because small particles make itpossible to reach the maximum ignition rate in fuel rich conditions, and large particles widen the range of possible airflow rates. A correlation was found forthe maximum rate of ignition front propagation in different wood fuels. According to the correlation, the maximum ignition mass flux is increased when the sphericity of the particles and the porosity of the bed are increased and the moisture content of the fuel is decreased. Another fit was found between sphericity and porosity. Increase in sphericity decreases the porosity of the bed. The reasons of the observed results are discussed.

Kattila-koski inunder Polar-Cirkeln

Helsingfors : A.W. Gröndahl & A.C. Öhman 1845 : Dresden, Adler u. Dietze

Valamo a short handbook for travellers - [Front cover]

Helsinki : The Finnish Tourist Association 1926

A Generic Framework Architecture for Portal Front End

A modem software development requires quick results and excellent quality, which leads to high demand for reusability in design and implementation of software components. The purpose of this thesis was to design and implement a reusable framework for portal front ends, including common portal features, such as authentication and authorization. The aim was also to evaluate frameworks as components of reuse and compare them to other reuse techniques. As the result of this thesis, a goo'd picture of framework's life cycle, problem domain and the actual implementation process of the framework, was obtained. It was also found out that frameworks fit well to solve recurrent and similar problems in a restricted problem domain. The outcome of this thesis was a prototype of a generic framework and an example application built on it. The implemented framework offered an abstract base for the portal front ends, using object-oriented methods and wellknown design patterns. The example application demonstrated the speed and ease of the application development based on the application frameworks.

Applying Active Front End To Multilevel Inverter

The aim of this work was to make an active front end from IGBTs for a multilevel inverter. The work was done for Mosart II, a long term still ongoing Vacon Oyj project. The purpose of the AFE is to balance the DC-voltage and to put the returning power back to the grid instead of the breaking chopper and the capacitor. With a diode rectifier the bridge only allows power to pass in one direction and the switching times are not controllable. That means the rectifier always takes the highest phase and the phases are always conducting the same 120◦. With an AFE it is possible to actively change the rectifiers switching pattern. A diode bridge also generates much greater losses than an IGBT bridge. With these arguments it is rational to start researching the possibility of an AFE in a multilevel inverter.

Managing the Front End of Innovation in a Networked Company Environment - Combining Strategy, Processes and Systems of Innovation

The objective of the thesis is to enhance the understanding about the management of the front end phases of the innovation process in a networked environment. The thesis approaches the front end of innovation from three perspectives, including the strategy, processes and systems of innovation. The purpose of the use of different perspectives in the thesis is that of providing an extensive systemic view of the front end, and uncovering the complex nature of innovation management. The context of the research is the networked operating environment of firms. The unit of analysis is the firm itself or its innovation processes, which means that this research approaches the innovation networks from the point of view of a firm. The strategy perspective of the thesis emphasises the importance of purposeful innovation management, the innovation strategy of firms. The role of innovation processes is critical in carrying out innovation strategies in practice, supporting the development of organizational routines for innovation, and driving the strategic renewal of companies. The primary focus of the thesis from systems perspective is on idea management systems, which are defined as a part of innovation management systems, and defined for this thesis as any working combination of methodology and tools (manual or IT-supported) that enhance the management of innovations within their early phases. The main contribution of the thesis are the managerial frameworks developed for managing the front end of innovation, which purposefully “wire” the front end of innovation into the strategy and business processes of a firm. The thesis contributes to modern innovation management by connecting the internal and external collaboration networks as foundational elements for successful management of the early phases of innovation processes in a dynamic environment. The innovation capability of a firm is largely defined by its ability to rely on and make use of internal and external collaboration already during the front end activities, which by definition include opportunity identification and analysis, idea generation, profileration and selection, and concept definition. More specifically, coordination of the interfaces between these activities, and between the internal and external innovation environments of a firm is emphasised. The role of information systems, in particular idea management systems, is to support and delineate the innovation-oriented behaviour and interaction of individuals and organizations during front end activities. The findings and frameworks developed in the thesis can be used by companies for purposeful promotion of their front end processes. The thesis provides a systemic strategy framework for managing the front end of innovation – not as a separate process, but as an elemental bundle ofactivities that is closely linked to the overall innovation process and strategy of a firm in a distributed environment. The theoretical contribution of the thesis relies on the advancement of the open innovation paradigm in the strategic context of a firm within its internal and external innovation environments. This thesis applies the constructive research approach and case study methodology to provide theoretically significant results, which are also practically beneficial.

Applying collective intelligence to idea evaluation at the front end of innovation

The study focuses on the front end of innovation process. Due to changes in innovation policies and paradigms customers, users and shopfloor employees are becoming increasingly important sources of knowledge. New methods are needed for processing information and ideas coming from multiple sources more effectively. The aim of this study is to develop an idea evaluation tool suitable for the front end of innovation process and capable of utilizing collective intelligence. The study is carried out as a case study research using constructive research approach. The chosen approach suits well for the purposes of the study. The constructive approach focuses on designing new constructs and testing them in real life applications. In this study a tool for evaluating ideas emerging from the course of everyday work is developed and tested in a case organization. Development of the tool is based on current scientific literature on knowledge creation, innovation management and collective intelligence and it is tested in LUT Lahti School of Innovation. Results are encouraging. The idea evaluation tool manages to improve performance at the front end of innovation process and it is accepted in use in the case organization. This study provides insights on what kind of a tool is required for facilitating collective intelligence at the front end of innovation process.

Challenges and Means for the Front End Activities of Software Development

The front end of innovation is regarded as one of the most important steps in building new software products or services, and the most significant benefits in software development can be achieved through improvements in the front end activities. Problems in the front end phase have an impact on customer dissatisfaction with delivered software, and on the effectiveness of the entire software development process. When these processes are improved, the likelihood of delivering high quality software and business success increases. This thesis highlights the challenges and problems related to the early phases of software development, and provides new methods and tools for improving performance in the front end activities of software development. The theoretical framework of this study comprises two fields of research. The first section belongs to the field of innovation management, and especially to the management of the early phases of the innovation process, i.e. the front end of innovation. The second section of the framework is closely linked to the processes of software engineering, especially to the early phases of the software development process, i.e. the practice of requirements engineering. Thus, this study extends the theoretical knowledge and discloses the differences and similarities in these two fields of research. In addition, this study opens up a new strand for academic discussion by connecting these research directions. Several qualitative business research methodologies have been utilized in the individual publications to solve the research questions. The theoretical and managerial contribution of the study can be divided into three areas: 1) processes and concepts, 2) challenges and development needs, and 3) means and methods for the front end activities of software development. First, the study discloses the difference and similarities between the concepts of the front end of innovation and requirements engineering, and proposes a new framework for managing the front end of the software innovation process, bringing business and innovation perspectives into software development. Furthermore, the study discloses managerial perceptions of the similarities and differences in the concept of the front end of innovation between the software industry and the traditional industrial sector. Second, the study highlights the challenges and development needs in the front end phase of software development, especially challenges in communication, such as linguistic problems, ineffective communication channels, a communication gap between users/customers and software developers, and participation of multiple persons in software development. Third, the study proposes new group methods for improving the front end activities of software development, especially customer need assessment, and the elicitation of software requirements.

The figure of the earth, determined from observations made by order of the French King, at the polar circle: by Messrs de Maupertuis, Camus, Clairaut, Le Monnier, members of the Royal Academy of Sciences, the abbé Outhier, correspondent of the Academy, and Mr. Celsius, professor of astronomy at Upsal : translated from the French of M. de Maupertuis.

Digital reproduction, The National Library of Finland, Centre for Preservation and Digitisation, Mikkeli

Development of a Radiometer Front End for Detection of Oil Spill on Sea Surface

Kaikki kappaleet säteilevät sähkömagneettista energiaa. Radiometreillä voidaan mitata tätä säteilyä, ja mittausten avulla voidaan kaukokartoituksessa analysoida monia ilmakehään ja maan pintaan liittyviä ilmiöitä. Säteilyä kerätään useimmiten radiometriin kytketyn antennin avulla. Mikroaaltoalueella säteilystä saatava teho on verrannollinen kohteen kirkkauslämpötilaan. Kirkkauslämpötila on puolestaan verrannollinen kohteen fyysiseen lämpötilaan materiaalin emissiivisyyden kautta. Emissiivisyys voi vaihdella suuresti eri pintojen ja materiaalien välillä. Näin ollen mittaamalla kohteen kirkkauslämpötilaa saadaan tietoa sen ominaisuuksista. Mikroaaltoradiometrin avulla voidaan havaita öljyläikkä meren pinnalta, sekä määrittää öljyläikän paksuus. Öljy muodostaa ohuen kalvon meren pinnalla. Ohuen kalvon ylä- ja alapinnasta heijastuneet aallot kulkevat eri matkan, jonka seurauksena muodostuu interferenssikuvio. Interferenssi on joko konstruktiivinen tai destruktiivinen riippuen heijastusten vaihe-erosta. Pistetaajuudella tästä seuraa kalvon paksuudesta riippuva sinimuotoinen emissiivisyys. Mallintamalla tämä ilmiö riittävän tarkasti voidaan radiometrin mittaamaa kirkkauslämpötilaa verrata mallinnettuun arvoon ja täten määrittää öljykerroksen paksuus. Tässä työssä esitetään kahden radiometrin suunnittelu ja testaus. Työ rajoittuu radiometrien alustavaan testausvaiheeseen. Radiometrit on suunniteltu 36,5GHz sekä 89GHz taajuuksille. Työn suurin kontribuutio on radiometrien etupään suunnittelussa ja testauksessa, kalibraatiomenetelmien kehittämisessä sekä kylmäkuorman suunnittelussa. Lisäksi työssä esitetään radiometrien systeemisuunnittelu sekä siihen liittyvät simulaatiot.

"Fuzzy front end" ja sen menestyksekäs johtaminen teollisuusyrityksessä

Työssä käsitellään innovaatioprosessin ensimmäistä ”fuzzy front end” -vaihetta, jota työssä kutsutaan front end -vaiheeksi. Front end -vaihe on innovaatioprosessin alustava tutkimus ja suunnittelu vaihe ennen teknistä kehittämisvaihetta. Front end -vaihetta on tutkittu innovaatioprosessin osista vähiten, sekä se on useimmille yrityksillä sumea ja vaikeasti käsitettävä. Tutkimusten mukaan front end -vaiheen osaaminen on kuitenkin erittäin merkittävä tekijä yrityksen innovatiivisuudelle. Työssä avataan innovaatioprosessin sisältöä ja tavoitteita, sekä vertaillaan käytössä olevia malleja front end -vaiheen rakenteesta. Työssä selvitetään avaintekijöitä front end -vaiheen menestykseen ja tehokkuuteen. Lisäksi käsitellään johtamisen tekijöitä, jotka edesauttavat onnistumaan front end -vaiheessa.

The early activities of front end of innovation in oem companies using a new fei platform as a framework for renewal

The main goal of this study is to create a seamless chain of actions and more detailed structure to the front end of innovation to be able to increase the front end performance and finally to influence the renewal of companies. The main goal is achieved through by the new concept of an integrated model of early activities of FEI leading to a discovery of new elements of opportunities and the identification of new business and growth areas. The procedure offers one possible solution to a dynamic strategy formation process in innovation development cycle. In this study the front end of innovation is positioned between a strategy reviews and a concept creation with needed procedures, tools, and frameworks. The starting point of the study is that the origins of innovation are not well enough understood. The study focuses attention on the early activities of FEI. These first activities are conceptualized in order to find out successful innovation initiatives and strategic renewal agendas. A seamless chain of activities resulting in faster and more precise identification of opportunities and growth areas available on markets and inside companies is needed. Three case studies were conducted in order to study company views on available theory doctrine and to identify the first practical experiences and procedures in the beginning of the front end of innovation. Successful innovation requires focus on renewal in both internal and external directions and they should be carefully balanced for best results. Instead of inside-out mode of actions the studied companies have a strong outside-in thinking mode and they mainly co-develop their innovation initiatives in close proximity with customers i.e. successful companies are an integral part of customers business and success. Companies have tailor-made innovation processes combined their way of working linked to their business goals, and priorities of actual needs of transformation. The result of this study is a new modular FEI platform which can be configured by companies against their actual business needs and drivers. This platform includes new elements of FEI documenting an architecture presenting how the system components work together. The system is a conceptual approach from theories of emergent strategy formation, opportunity identification and creation, interpretation-analysis-experimentation triad and the present FEI theories. The platform includes new features compared to actual models of FEI. It allows managers to better understand the importance of FEI in the whole innovation development stage and FEI as a phase and procedure to discover and implement emergent strategy. An adaptable company rethinks and redirects strategy proactively from time to time. Different parts of the business model are changed to remove identified obstacles for growth and renewal which gives them avenues to find right reforms for renewal.

Modeling Front End Electronics for a Gas Electron Multiplier Detector

The Large Hadron Collider (LHC) in The European Organization for Nuclear Research (CERN) will have a Long Shutdown sometime during 2017 or 2018. During this time there will be maintenance and a possibility to install new detectors. After the shutdown the LHC will have a higher luminosity. A promising new type of detector for this high luminosity phase is a Triple-GEM detector. During the shutdown these detectors will be installed at the Compact Muon Solenoid (CMS) experiment. The Triple-GEM detectors are now being developed at CERN and alongside also a readout ASIC chip for the detector. In this thesis a simulation model was developed for the ASICs analog front end. The model will help to carry out more extensive simulations and also simulate the whole chip before the whole design is finished. The proper functioning of the model was tested with simulations, which are also presented in the thesis.