Cuticular and Suberin Polymers of Edible Plants. Analysis by Gas Chromatographic-Mass Spectrometric and Solid State Spectroscopic Methods

Cutin and suberin are structural and protective polymers of plant surfaces. The epidermal cells of the aerial parts of plants are covered with an extracellular cuticular layer, which consists of polyester cutin, highly resistant cutan, cuticular waxes and polysaccharides which link the layer to the epidermal cells. A similar protective layer is formed by a polyaromatic-polyaliphatic biopolymer suberin, which is present particularly in the cell walls of the phellem layer of periderm of the underground parts of plants (e.g. roots and tubers) and the bark of trees. In addition, suberization is also a major factor in wound healing and wound periderm formation regardless of the plants’ tissue. Knowledge of the composition and functions of cuticular and suberin polymers is important for understanding the physiological properties for the plants and for nutritional quality when these plants are consumed as foods. The aims of the practical work were to assess the chemical composition of cuticular polymers of several northern berries and seeds and suberin of two varieties of potatoes. Cutin and suberin were studied as isolated polymers and further after depolymerization as soluble monomers and solid residues. Chemical and enzymatic depolymerization techniques were compared and a new chemical depolymerization method was developed. Gas chromatographic analysis with mass spectrometric detection (GC-MS) was used to assess the monomer compositions. Polymer investigations were conducted with solid state carbon-13 cross polarization magic angle spinning nuclear magnetic resonance spectroscopy (13C CP-MAS NMR), Fourier transform infrared spectroscopy (FTIR) and microscopic analysis. Furthermore, the development of suberin over one year of post-harvest storage was investigated and the cuticular layers from berries grown in the North and South of Finland were compared. The results show that the amounts of isolated cuticular layers and cutin monomers, as well as monomeric compositions vary greatly between the berries. The monomer composition of seeds was found to differ from the corresponding berry peel monomers. The berry cutin monomers were composed mostly of long-chain aliphatic ω-hydroxy acids, with various mid-chain functionalities (double-bonds, epoxy, hydroxy and keto groups). Substituted α,ω-diacids predominated over ω-hydroxy acids in potato suberin monomers and slight differences were found between the varieties. The newly-developed closed tube chemical method was found to be suitable for cutin and suberin analysis and preferred over the solvent-consuming and laborious reflux method. Enzymatic hydrolysis with cutinase was less effective than chemical methanolysis and showed specificity towards α,ω-diacid bonds. According to ₁₃C CP-MAS NMR and FTIR, the depolymerization residues contained significant amounts of aromatic structures, polysaccharides and possible cutan-type aliphatic moieties. Cultivation location seems to have effect on cuticular composition. The materials studied contained significant amounts of different types of biopolymers that could be utilized for several purposes with or without further processing. The importance of the so-called waste material from industrial processes of berries and potatoes as a source of either dietary fiber or specialty chemicals should be further investigated in detail. The evident impact of cuticular and suberin polymers, among other fiber components, on human health should be investigated in clinical trials. These by-product materials may be used as value-added fiber fractions in the food industry and as raw materials for specialty chemicals such as lubricants and emulsifiers, or as building blocks for novel polymers.

Smart homes as service platforms. Research report of ÄLYKOP sub-project “Competitive advantage from customer value”

In this report, we summarize results of our part of the ÄLYKOP-project on customer value creation in the intersection of the health care, ICT, forest and energy industries. The research directs to describe how industry transformation and convergence create new possibilities, business opportunities and even new industries.The report consists of findings which are presented former in academic publications. The publication discusses on customer value, service provision and resource basis of the novel concepts through multiple theorethical frameworks. The report is divided into three maim sections which are theoretical background, discussion on health care industry and evaluations regarding novel smart home concepts. Transaction cost economics and Resource- Based view on the firm provides the theoretical basis to analyze the prescribed phenomena. The health care industry analysis describes the most important changes in the demand conditions of health care services, and explores the features that are likely to open new business opportunities for a solution provider. The third part of the report on the smart home business provides illustrations few potential concepts that can be considered to provide solutions to economical problems which arise from aging of population. The results provide several recommendations for the smart home platform developers in public and private sectors. By the analysis, public organizations dominate service provision and private markets are emergent state at present. We argue that public-private partnerships are nececssary for creating key suppliers. Indeed, paying attion on appropriate regulation, service specifications and technology standards would foster diffusion of new services. The dynamics of the service provision networks is driven by need for new capabiltities which are required for adapting business concepts to new competitive situation. Finally, the smart home framework revealed links between conventionally distant business areas such as health care and energy distribution. The platform integrates functionalities different for purposes which however apply same resource basis.

Roles of novel biomarkers in progression of cutaneous squamous cell carcinoma

Roles of novel biomarkers was studied in progression of cutaneous squamous cell carcinoma (cSCC) as the most common metastatic skin cancer. The incidence of cSCC is increasing worldwide due to lifestyle changes such as recreational exposure to sunlight and the aging of the population. Because of an emerging need for molecular markers for the progression of cSCC, we set our goal to characterize three distinct novel markers overexpressed in cSCC cells. Our results identified overexpression of serpin peptidase inhibitor clade A member 1 (SerpinA1), EphB2 and absent in melanoma 2 (AIM2) in cSCC cell lines compared with normal human epidermal keratinocytes (NHEKs). Immunohistochemical analysis of SerpinA1, EphB2 and AIM2 revealed abundant tumor cell-specific expression of cytoplasmic SerpinA1 and AIM2 and cytoplasmic and membranous EphB2 in cSCC tumors in vivo. The staining intensity of SerpinA1, EphB2 and AIM2 was significantly stronger in cSCC as compared with carcinoma in situ (cSCCIS) and actinic keratosis (AK). Tumor cell-associated SerpinA1 and EphB2 was noted in chemically induced mouse skin SCC, and the staining intensity was stronger in mouse cSCCs than in untreated skin. AIM2 staining intensity was significantly more abundant in cSCC of organ transplant recipients (OTR) than in sporadic cSCC in vivo. EphB2 knockdown resulted in inhibition of migration in cSCC cells. In addition, knockdown of EphB2 and AIM2 was found to inhibit the proliferation and invasion of cSCC cells and to delay the growth and vascularization of cSCC xenografts in vivo. Altogether, these findings identify SerpinA1 as a novel biomarker for cSCC. In addition, characterization of the roles of EphB2 and AIM2 in the progression of cSCC was implicated them as possible therapeutic targets for the treatment of cSCC particularly in unresectable and metastatic tumors.

Sähkönsiirtoyritysten kunnossapidon taloudellinen malli

Sähkönsiirtoyritysten kunnossapidon taloudellinen malli eli SKUTMA, on sähköverkkoyhtiöille suunniteltu luotettavuuspohjainen kunnossapitomalli, mikä priorisoi ja ajoittaa sähkönjakeluverkon komponenttien huolto- ja investointiajankohdat. Malli hyödyntää dynaamisen optimoinnin algoritmia kustannusminimien löytämiseksi tarkastelujaksolta ja simuloi komponenttien rappeutumasta rappeutumismallin avulla. Tässä diplomityössä on kehitetty kunnossapito-ohjelma SKUTMA-mallin pohjalta, minkä avulla tutkitaan mallin toimivuutta oikeilla johtolähdöillä ja sen hyödyntämistä sähköverkkojen kunnossapidon suunnittelussa. Työssä käydään läpi myös kunnossapitoohjelman laskenta metodiikkaa ja sen ominaisuuksia. Tämän työn lopputuloksena saadaan selkeä kuva mallin toiminnasta, käytettävyydestä ja jatkokehityspotentiaalista.

Insulation System in an Integrated Motor Compressor

A high-speed and high-voltage solid-rotor induction machine provides beneficial features for natural gas compressor technology. The mechanical robustness of the machine enables its use in an integrated motor-compressor. The technology uses a centrifugal compressor, which is mounted on the same shaft with the high-speed electrical machine driving it. No gearbox is needed as the speed is determined by the frequency converter. The cooling is provided by the process gas, which flows through the motor and is capable of transferring the heat away from the motor. The technology has been used in the compressors in the natural gas supply chain in the central Europe. New areas of application include natural gas compressors working at the wellheads of the subsea gas reservoir. A key challenge for the design of such a motor is the resistance of the stator insulation to the raw natural gas from the well. The gas contains water and heavy hydrocarbon compounds and it is far harsher than the sales gas in the natural gas supply network. The objective of this doctoral thesis is to discuss the resistance of the insulation to the raw natural gas and the phenomena degrading the insulation. The presence of partial discharges is analyzed in this doctoral dissertation. The breakdown voltage of the gas is measured as a function of pressure and gap distance. The partial discharge activity is measured on small samples representing the windings of the machine. The electrical field behavior is also modeled by finite element methods. Based on the measurements it has been concluded that the discharges are expected to disappear at gas pressures above 4 – 5 bar. The disappearance of discharges is caused by the breakdown strength of the gas, which increases as the pressure increases. Based on the finite element analysis, the physical length of a discharge seen in the PD measurements at atmospheric pressure was approximated to be 40 – 120 m. The chemical aging of the insulation when exposed to raw natural gas is discussed based on a vast set of experimental tests with the gas mixture representing the real gas mixture at the wellhead. The mixture was created by mixing dry hydrocarbon gas, heavy hydrocarbon compounds, monoethylene glycol, and water. The mixture was chosen to be more aggressive by increasing the amount of liquid substances. Furthermore, the temperature and pressure were increased, which resulted in accelerated test conditions. The time required to detect severe degradation was thus decreased. The test program included a comparison of materials, an analysis of the e ects of di erent compounds in the gas mixture, namely water and heavy hydrocarbons, on the aging, an analysis of the e ects of temperature and exposure duration, and also an analysis on the e ect of sudden pressure changes on the degradation of the insulating materials. It was found in the tests that an insulation consisting of mica, glass, and epoxy resin can tolerate the raw natural gas, but it experiences some degradation. The key material in the composite insulation is the resin, which largely defines the performance of the insulation system. The degradation of the insulation is mostly determined by the amount of gas mixture di used into it. The di usion was seen to follow Fick’s second law, but the coe cients were not accurately defined. The di usion was not sensitive to temperature, but it was dependent upon the thermodynamic state of the gas mixture, in other words, the amounts of liquid components in the gas. The weight increase observed was mostly related to heavy hydrocarbon compounds, which act as plasticizers in the epoxy resin. The di usion of these compounds is determined by the crosslink density of the resin. Water causes slight changes in the chemical structure, but these changes do not significantly contribute to the aging phenomena. Sudden changes in pressure can lead to severe damages in the insulation, because the motion of the di used gas is able to create internal cracks in the insulation. Therefore, the di usion only reduces the mechanical strength of the insulation, but the ultimate breakdown can potentially be caused by a sudden drop in the pressure of the process gas.

Diskreettiaikainen liukuvan moodin säätö kiinteäoksidipolttokennon DC-tasonnostossa

Huoli ympäristön tilasta ja fossiilisten polttoaineiden hinnan nousu ovat vauhdittaneet tutkimusta uusien energialähteiden löytämiseksi. Polttokennot ovat yksi lupaavimmista tekniikoista etenkin hajautetun energiantuotannon, varavoimalaitosten sekä liikennevälineiden alueella. Polttokenno on tehonlähteenä kuitenkin hyvin epäideaalinen, ja se asettaa tehoelektroniikalle lukuisia erityisvaatimuksia. Polttokennon kytkeminen sähköverkkoon on tavallisesti toteutettu käyttämällä galvaanisesti erottavaa DC/DC hakkuria sekä vaihtosuuntaajaa sarjassa. Polttokennon kulumisen estämiseksi tehoelektroniikalta vaaditaan tarkkaa polttokennon lähtövirran hallintaa. Perinteisesti virran hallinta on toteutettu säätämällä hakkurin tulovirtaa PI (Proportional and Integral) tai PID (Proportional, Integral and Derivative) -säätimellä. Hakkurin epälineaarisuudesta johtuen tällainen ratkaisu ei välttämättä toimi kaukana linearisointipisteestä. Lisäksi perinteiset säätimet ovat herkkiä mallinnusvirheille. Tässä diplomityössä on esitetty polttokennon jännitettä nostavan hakkurin tilayhtälökeskiarvoistusmenetelmään perustuva malli, sekä malliin perustuva diskreettiaikainen integroiva liukuvan moodin säätö. Esitetty säätö on luonteeltaan epälineaarinen ja se soveltuu epälineaaristen ja heikosti tunnettujen järjestelmien säätämiseen.

Challenges in transferring the hydropower control centre

Euroopan sähkömarkkinat ovat viime vuosikymmeninä olleet suurien muutoksien kohteena näiden yhtenäistämisprojektin seurauksena. Fortum, yksi Euroopan johtavista energia-alan yrityksistä valmistautuu tähän muutokseen toteuttamalla omia yrityksen sisäisiä muutoksia, tavoitteenaan yksinkertaistaa organisaatiorakennettaan ja parantaa tehokkuuttaan. Yksi suuri muutos tähän liittyen on vesivoimavalvomojen lokalisaatioprojekti. Vesivoimavalvomojen uudelleenlokalisaation ja vesivoiman käytönvalvojien ikääntymisen myötä nähtiin tarpeelliseksi tehdä tutkimus käytönvalvojien hiljaisesta tiedosta. Näin ollen, tässä diplomityössä perehdyttiin Fortumin vesivoiman käytönvalvojien kompetensseihin ja näiden hiljaiseen tietoon. Tutkimusaiheena oli selvittää minkälaista hiljaista tietoa käytönvalvojat omaavat, ja mikä osa tästä tiedosta muodostaa sen kriittisen osaamisen, jota halutaan säilyttää ja kehittää. Tutkimustyypiksi muodostui kvalitatiivinen, jonka päämetodi oli puoli-avoin haastattelu. Tutkimus koostui seuraavista vaiheista: tarkkailu, tekstianalyysi, haastattelu, transkriptio ja data analyysi. Haastatteluja tehtiin kahdeksan, joista kerääntyi yli 24 tuntia haastattelumateriaalia. Tästä materiaalista muodostettiin analyysien avulla taulukko, jonka avulla tunnistettiin ne osa-alueet, joihin käytönvalvojan tärkeimmät kompetenssit liittyvät. Tuloksilla saatiin myös kerättyä lista korjaus- ja kehityskohteista, sekä tarkemmat määritykset jatkotutkimukselle.

Yrityksen tuoterakenteen määrittäminen olioparadigmalla

Tässä työssä tutkitaan yrityksen tuoterakenteen toteuttamista olioparadigmalla osana vanhenevan tuotannonohjausjärjestelmän uudistamista. Työssä on tunnistettu olioparadigman keskeiset rakenteet sekä tarkasteltu suunnittelumalleja, joita hyödyntämällä voidaan määrittää ja toteuttaa monimutkaisia sekä laajennettavia tuoterakenteita. Työn tavoitteena oli muodostaa tuoterakenteen runko, jota muokkaamalla on mahdollista toteuttaa erityyppisiä tuoterakenteita. Työ on rajattu siten, että todellista tuoterakennetta ei toteuteta. Tutkimuksen tuloksena havaittiin, että oliokeskeisyydellä voidaan toteuttaa tuoterakenteita, joita on mahdollista tulevaisuudessa muokata yrityksen tarpeisiin mukauttaen siten, että tuoterakenteen runkoon ei tarvitse tehdä suuria muutoksia. Olioperusteisella lähestymisellä voidaan mallintaa hyvin erityyppisiä ja ymmärrettäviä käsitteitä. Oliokeskeisellä lähestymistavalla voidaan toteuttaa myös muut vanhenevan tuotannonohjausjärjestelmän osa-alueet.

Tietovirtojen hyödyntäminen alueellisen terveysjärjestelmän johtamisessa

Julkinen terveydenhuollon toimintaympäristö on muuttumassa. Terveydenhuollon käytettävissä olevat resurssit ovat heikkenemässä yleisen taloudellisen tilanteen ja väestön ikääntymisen johdosta. Terveydenhuollon palvelurakenteita ollaan uudistamassa. Merkittävien päätösten perusteiksi ja organisaatioiden johtamisen tueksi tarvitaan tietoa ja tietovirtoja. Tutkimus toteutettiin kvalitatiivisena tutkimuksena, jonka empiirinen osuus toteutettiin erikoissairaanhoidon palveluita tuottavassa keskussairaalassa. Haastatteluaineisto kerättiin sairaalan ylimmästä johdosta. Tutkimuksen mukaan informaatio-ohjaukseen, asiantuntijoiden johtamiseen ja palvelutuotannon vaikuttavuuteen liittyvät tietovirrat ovat alueellisen terveydenhuollon organisaation keskeisiä tietovirtoja.