Torque vibration model of axial-flux surface-mounted permanent magnet synchronous machine

In order that the radius and thus ununiform structure of the teeth and otherelectrical and magnetic parts of the machine may be taken into consideration the calculation of an axial flux permanent magnet machine is, conventionally, doneby means of 3D FEM-methods. This calculation procedure, however, requires a lotof time and computer recourses. This study proves that also analytical methods can be applied to perform the calculation successfully. The procedure of the analytical calculation can be summarized into following steps: first the magnet is divided into slices, which makes the calculation for each section individually, and then the parts are submitted to calculation of the final results. It is obvious that using this method can save a lot of designing and calculating time. Thecalculation program is designed to model the magnetic and electrical circuits of surface mounted axial flux permanent magnet synchronous machines in such a way, that it takes into account possible magnetic saturation of the iron parts. Theresult of the calculation is the torque of the motor including the vibrations. The motor geometry and the materials and either the torque or pole angle are defined and the motor can be fed with an arbitrary shape and amplitude of three-phase currents. There are no limits for the size and number of the pole pairs nor for many other factors. The calculation steps and the number of different sections of the magnet are selectable, but the calculation time is strongly depending on this. The results are compared to the measurements of real prototypes. The permanent magnet creates part of the flux in the magnetic circuit. The form and amplitude of the flux density in the air-gap depends on the geometry and material of the magnetic circuit, on the length of the air-gap and remanence flux density of the magnet. Slotting is taken into account by using the Carter factor in the slot opening area. The calculation is simple and fast if the shape of the magnetis a square and has no skew in relation to the stator slots. With a more complicated magnet shape the calculation has to be done in several sections. It is clear that according to the increasing number of sections also the result will become more accurate. In a radial flux motor all sections of the magnets create force with a same radius. In the case of an axial flux motor, each radial section creates force with a different radius and the torque is the sum of these. The magnetic circuit of the motor, consisting of the stator iron, rotor iron, air-gap, magnet and the slot, is modelled with a reluctance net, which considers the saturation of the iron. This means, that several iterations, in which the permeability is updated, has to be done in order to get final results. The motor torque is calculated using the instantaneous linkage flux and stator currents. Flux linkage is called the part of the flux that is created by the permanent magnets and the stator currents passing through the coils in stator teeth. The angle between this flux and the phase currents define the torque created by the magnetic circuit. Due to the winding structure of the stator and in order to limit the leakage flux the slot openings of the stator are normally not made of ferromagnetic material even though, in some cases, semimagnetic slot wedges are used. In the slot opening faces the flux enters the iron almost normally (tangentially with respect to the rotor flux) creating tangential forces in the rotor. This phenomenon iscalled cogging. The flux in the slot opening area on the different sides of theopening and in the different slot openings is not equal and so these forces do not compensate each other. In the calculation it is assumed that the flux entering the left side of the opening is the component left from the geometrical centre of the slot. This torque component together with the torque component calculated using the Lorenz force make the total torque of the motor. It is easy to assume that when all the magnet edges, where the derivative component of the magnet flux density is at its highest, enter the slot openings at the same time, this will have as a result a considerable cogging torque. To reduce the cogging torquethe magnet edges can be shaped so that they are not parallel to the stator slots, which is the common way to solve the problem. In doing so, the edge may be spread along the whole slot pitch and thus also the high derivative component willbe spread to occur equally along the rotation. Besides forming the magnets theymay also be placed somewhat asymmetric on the rotor surface. The asymmetric distribution can be made in many different ways. All the magnets may have a different deflection of the symmetrical centre point or they can be for example shiftedin pairs. There are some factors that limit the deflection. The first is that the magnets cannot overlap. The magnet shape and the relative width compared to the pole define the deflection in this case. The other factor is that a shifting of the poles limits the maximum torque of the motor. If the edges of adjacent magnets are very close to each other the leakage flux from one pole to the other increases reducing thus the air-gap magnetization. The asymmetric model needs some assumptions and simplifications in order to limit the size of the model and calculation time. The reluctance net is made for symmetric distribution. If the magnets are distributed asymmetrically the flux in the different pole pairs will not be exactly the same. Therefore, the assumption that the flux flows from the edges of the model to the next pole pairs, in the calculation model from one edgeto the other, is not correct. If it were wished for that this fact should be considered in multi-pole pair machines, this would mean that all the poles, in other words the whole machine, should be modelled in reluctance net. The error resulting from this wrong assumption is, nevertheless, irrelevant.

THE IMPACT OF ARCHITECTURAL DESIGN ON SOFTWARE DEVELOPMENT

Tässä työssä tutkitaan ohjelmistoarkkitehtuurisuunnitteluominaisuuksien vaikutusta erään client-server –arkkitehtuuriin perustuvan mobiilipalvelusovelluksen suunnittelu- ja toteutusaikaan. Kyseinen tutkimus perustuu reaalielämän projektiin, jonka kvalitatiivinen analyysi paljasti arkkitehtuurikompponenttien välisten kytkentöjen merkittävästi vaikuttavan projektin työmäärään. Työn päätavoite oli kvantitatiivisesti tutkia yllä mainitun havainnon oikeellisuus. Tavoitteen saavuttamiseksi suunniteltiin ohjelmistoarkkitehtuurisuunnittelun mittaristo kuvaamaan kyseisen järjestelmän alijärjestelmien arkkitehtuuria ja luotiin kaksi suunniteltua mittaristoa käyttävää, työmäärää (komponentin suunnittelu-, toteutus- ja testausaikojen summa) arvioivaa mallia, joista toinen on lineaarinen ja toinen epälineaarinen. Näiden mallien kertoimet sovitettiin optimoimalla niiden arvot epälineaarista gloobaalioptimointimenetelmää, differentiaalievoluutioalgoritmia, käyttäen, niin että mallien antamat arvot vastasivat parhaiten mitattua työmäärää sekä kaikilla ominaisuuksilla eli attribuuteilla että vain osalla niistä (yksi jätettiin vuorotellen pois). Kun arkkitehtuurikompenttien väliset kytkennät jätettiin malleista pois, mitattujen ja arvoitujen työmäärien välinen ero (ilmaistuna virheenä) kasvoi eräässä tapauksessa 367 % entisestä tarkoittaen sitä, että näin muodostettu malli vastasi toteutusaikoja huonosti annetulla ainestolla. Tämä oli suurin havaitu virhe kaikkien poisjätettyjen ominaisuuksien kesken. Saadun tuloksen perusteella päätettiin, että kyseisen järjestelmän toteutusajat ovat vahvasti riippuvaisia kytkentöjen määrästä, ja näin ollen kytkentöjen määrä oli mitä todennäköisemmin kaikista tärkein työmäärään vaikuttava tekijä tutkitun järjestelmän arkkitehtuurisuunnittelussa.

Integrating Group Support Systems to innovation process of a forest company

The objective of this study was to analyze the effects of Group Support Systems (GSS) to overall efficiency of innovation process. Overall efficiency was found to be a sum of meeting efficiency, product effectiveness, and learning efficiency. These components were studied in various working situations common in early stages of innovation process. In the empirical part of this study, the suitability of GSS at the forest company was assessed. The basics for this study were idea generation meetings held at LUT and results from the surveys done after the sessions. This data combined with the interviews and theoretical background was used to analyze suitability of this technology to organizational culture at the company. The results of this study are divided to theory and case level. On theory level GSS was found to be a potentially valuable tool for innovation managers, especially at the first stages of the process. On case level, GSS was found to be a suitable tool at Stora Enso for further utilization. A five step implementation proposal was built to illustrate what would be the next stages of GSS implementation, if technology was chosen for further implementation.

On Short Exponential Sums Involving Fourier Coefficients of Holomorphic Cusp Forms

By an exponential sum of the Fourier coefficients of a holomorphic cusp form we mean the sum which is formed by first taking the Fourier series of the said form,then cutting the beginning and the tail away and considering the remaining sum on the real axis. For simplicity’s sake, typically the coefficients are normalized. However, this isn’t so important as the normalization can be done and removed simply by using partial summation. We improve the approximate functional equation for the exponential sums of the Fourier coefficients of the holomorphic cusp forms by giving an explicit upper bound for the error term appearing in the equation. The approximate functional equation is originally due to Jutila [9] and a crucial tool for transforming sums into shorter sums. This transformation changes the point of the real axis on which the sum is to be considered. We also improve known upper bounds for the size estimates of the exponential sums. For very short sums we do not obtain any better estimates than the very easy estimate obtained by multiplying the upper bound estimate for a Fourier coefficient (they are bounded by the divisor function as Deligne [2] showed) by the number of coefficients. This estimate is extremely rough as no possible cancellation is taken into account. However, with small sums, it is unclear whether there happens any remarkable amounts of cancellation.

Phase voltage control and filtering in a converter-fed single-phase customer-end system of the LVDC distribution network

In recent years, the network vulnerability to natural hazards has been noticed. Moreover, operating on the limits of the network transmission capabilities have resulted in major outages during the past decade. One of the reasons for operating on these limits is that the network has become outdated. Therefore, new technical solutions are studied that could provide more reliable and more energy efficient power distributionand also a better profitability for the network owner. It is the development and price of power electronics that have made the DC distribution an attractive alternative again. In this doctoral thesis, one type of a low-voltage DC distribution system is investigated. Morespecifically, it is studied which current technological solutions, used at the customer-end, could provide better power quality for the customer when compared with the current system. To study the effect of a DC network on the customer-end power quality, a bipolar DC network model is derived. The model can also be used to identify the supply parameters when the V/kW ratio is approximately known. Although the model provides knowledge of the average behavior, it is shown that the instantaneous DC voltage ripple should be limited. The guidelines to choose an appropriate capacitance value for the capacitor located at the input DC terminals of the customer-end are given. Also the structure of the customer-end is considered. A comparison between the most common solutions is made based on their cost, energy efficiency, and reliability. In the comparison, special attention is paid to the passive filtering solutions since the filter is considered a crucial element when the lifetime expenses are determined. It is found out that the filter topology most commonly used today, namely the LC filter, does not provide economical advantage over the hybrid filter structure. Finally, some of the typical control system solutions are introduced and their shortcomings are presented. As a solution to the customer-end voltage regulation problem, an observer-based control scheme is proposed. It is shown how different control system structures affect the performance. The performance meeting the requirements is achieved by using only one output measurement, when operating in a rigid network. Similar performance can be achieved in a weak grid by DC voltage measurement. An additional improvement can be achieved when an adaptive gain scheduling-based control is introduced. As a conclusion, the final power quality is determined by a sum of various factors, and the thesis provides the guidelines for designing the system that improves the power quality experienced by the customer.

Profiling the Value of Industrial Maintenance Services

Industrial maintenance can be executed internally, acquired from the original equipment manufacturer or outsourced to a service provider, and this concludes in many different kind of business relationships. To maximize the total value in a maintenance business relationship it is important to know what the partner values. The value of maintenance services can be considered to consist of value elements and the perceived total value for the customer and the service provider is the sum of these value elements. The specific objectives of this thesis are to identify the most important value elements for the maintenance service customer and provider and also to recognize where the value elements differ. The study was executed as a statistical analysis using the survey method. The data has been collected by an online survey sent to 345 maintenance service professionals in Finland. In the survey, four different types of value elements were considered: the customer’s high critical and low critical items and the service provider’s core and support service. The most valued elements by the respondents were reliability, safety at work, environmental safety, and operator knowledge. The least valued elements were asset management factors and access to markets. Statistically significant differences in value elements between service types were also found. As a managerial implication a value gap profile is presented. This Master’s Thesis is part of the MaiSeMa (Industrial Maintenance Services in a Renewing Business Network: Identify, Model and Manage Value) research project where network decision models are created to identify, model and manage the value of maintenance services.

Bayesian analysis of SEIR epidemic models

This thesis concerns the analysis of epidemic models. We adopt the Bayesian paradigm and develop suitable Markov Chain Monte Carlo (MCMC) algorithms. This is done by considering an Ebola outbreak in the Democratic Republic of Congo, former Zaïre, 1995 as a case of SEIR epidemic models. We model the Ebola epidemic deterministically using ODEs and stochastically through SDEs to take into account a possible bias in each compartment. Since the model has unknown parameters, we use different methods to estimate them such as least squares, maximum likelihood and MCMC. The motivation behind choosing MCMC over other existing methods in this thesis is that it has the ability to tackle complicated nonlinear problems with large number of parameters. First, in a deterministic Ebola model, we compute the likelihood function by sum of square of residuals method and estimate parameters using the LSQ and MCMC methods. We sample parameters and then use them to calculate the basic reproduction number and to study the disease-free equilibrium. From the sampled chain from the posterior, we test the convergence diagnostic and confirm the viability of the model. The results show that the Ebola model fits the observed onset data with high precision, and all the unknown model parameters are well identified. Second, we convert the ODE model into a SDE Ebola model. We compute the likelihood function using extended Kalman filter (EKF) and estimate parameters again. The motivation of using the SDE formulation here is to consider the impact of modelling errors. Moreover, the EKF approach allows us to formulate a filtered likelihood for the parameters of such a stochastic model. We use the MCMC procedure to attain the posterior distributions of the parameters of the SDE Ebola model drift and diffusion parts. In this thesis, we analyse two cases: (1) the model error covariance matrix of the dynamic noise is close to zero , i.e. only small stochasticity added into the model. The results are then similar to the ones got from deterministic Ebola model, even if methods of computing the likelihood function are different (2) the model error covariance matrix is different from zero, i.e. a considerable stochasticity is introduced into the Ebola model. This accounts for the situation where we would know that the model is not exact. As a results, we obtain parameter posteriors with larger variances. Consequently, the model predictions then show larger uncertainties, in accordance with the assumption of an incomplete model.