CFD Modelling of Direct Contact Condensation in Suppression Pools by Applying Condensation Models of Separated Flow

The condensation rate has to be high in the safety pressure suppression pool systems of Boiling Water Reactors (BWR) in order to fulfill their safety function. The phenomena due to such a high direct contact condensation (DCC) rate turn out to be very challenging to be analysed either with experiments or numerical simulations. In this thesis, the suppression pool experiments carried out in the POOLEX facility of Lappeenranta University of Technology were simulated. Two different condensation modes were modelled by using the 2-phase CFD codes NEPTUNE CFD and TransAT. The DCC models applied were the typical ones to be used for separated flows in channels, and their applicability to the rapidly condensing flow in the condensation pool context had not been tested earlier. A low Reynolds number case was the first to be simulated. The POOLEX experiment STB-31 was operated near the conditions between the ’quasi-steady oscillatory interface condensation’ mode and the ’condensation within the blowdown pipe’ mode. The condensation models of Lakehal et al. and Coste & Lavi´eville predicted the condensation rate quite accurately, while the other tested ones overestimated it. It was possible to get the direct phase change solution to settle near to the measured values, but a very high resolution of calculation grid was needed. Secondly, a high Reynolds number case corresponding to the ’chugging’ mode was simulated. The POOLEX experiment STB-28 was chosen, because various standard and highspeed video samples of bubbles were recorded during it. In order to extract numerical information from the video material, a pattern recognition procedure was programmed. The bubble size distributions and the frequencies of chugging were calculated with this procedure. With the statistical data of the bubble sizes and temporal data of the bubble/jet appearance, it was possible to compare the condensation rates between the experiment and the CFD simulations. In the chugging simulations, a spherically curvilinear calculation grid at the blowdown pipe exit improved the convergence and decreased the required cell count. The compressible flow solver with complete steam-tables was beneficial for the numerical success of the simulations. The Hughes-Duffey model and, to some extent, the Coste & Lavi´eville model produced realistic chugging behavior. The initial level of the steam/water interface was an important factor to determine the initiation of the chugging. If the interface was initialized with a water level high enough inside the blowdown pipe, the vigorous penetration of a water plug into the pool created a turbulent wake which invoked the chugging that was self-sustaining. A 3D simulation with a suitable DCC model produced qualitatively very realistic shapes of the chugging bubbles and jets. The comparative FFT analysis of the bubble size data and the pool bottom pressure data gave useful information to distinguish the eigenmodes of chugging, bubbling, and pool structure oscillations.

Voiko totuutta tavoittaa? : direct cinema -tyylisuunnan käyttö dokumenttielokuvassa

The subject of this study is the use of direct cinema style in documentary film. The main purpose of this thesis was to the research the ways in which direct cinema style attempts to show and achieve truth in documentary films. The following questions were posed: Is it possible to depict reality in a documentary film; how does the choice of using this style affect the final documentary? The essential purpose of this study was to try to see whether the direct cinema style works when trying to achieve truth in a documentary film. This work consints of two elements, the theoretical part and the short documentary. The theoretical part deals with the history, the truth, and the direct cinema- style in documentaries. The theoretical information of direct cinema has been used when making the short documentary. In the documentary Tuloaula 2 I have studied the way in which using direct cinema -style works in practise. The documentary has followed as strictly as possible the direct cinema style. I was the director, the cameraman and the editor of my documentary film. In the documentary film Tuloaula 2 it appeared that the direct cinema style works best when filming everyday life. By using this style it is easy for the director to observe and leave his own persona in the background. The strength in using the direct cinema style is that it enables the viewer to build his/her own impression on the subject. Even though the direct cinema style aims to achieve objectivity the director has to make numerous subjective choices during both the filming and the editing process. These subjective choices automatically effect the "truth" of the documentary film. The difficulty in a direct cinema style is the large amount of material. This often leads to a long editing phase, which is not often possible in the busy production schedules. The direct cinema style is not at its best when shooting people who are passive because their attention often focuses too much on the camera. In general, the best way to make a documentary film would be to use many documentary styles in one film and not to srictly concentrate on only one style.

Direct-on-line axial flux permanent magnet synchronous generator static and dynamic performance

In distributed energy production, permanent magnet synchronous generators (PMSG) are often connected to the grid via frequency converters, such as voltage source line converters. The price of the converter may constitute a large part of the costs of a generating set. Some of the permanent magnet synchronous generators with converters and traditional separately excited synchronous generators couldbe replaced by direct-on-line (DOL) non-controlled PMSGs. Small directly networkconnected generators are likely to have large markets in the area of distributed electric energy generation. Typical prime movers could be windmills, watermills and internal combustion engines. DOL PMSGs could also be applied in island networks, such as ships and oil platforms. Also various back-up power generating systems could be carried out with DOL PMSGs. The benefits would be a lower priceof the generating set and the robustness and easy use of the system. The performance of DOL PMSGs is analyzed. The electricity distribution companies have regulations that constrain the design of the generators being connected to the grid. The general guidelines and recommendations are applied in the analysis. By analyzing the results produced by the simulation model for the permanent magnet machine, the guidelines for efficient damper winding parameters for DOL PMSGs are presented. The simulation model is used to simulate grid connections and load transients. The damper winding parameters are calculated by the finite element method (FEM) and determined from experimental measurements. Three-dimensional finite element analysis (3D FEA) is carried out. The results from the simulation model and 3D FEA are compared with practical measurements from two prototype axial flux permanent magnet generators provided with damper windings. The dimensioning of the damper winding parameters is case specific. The damper winding should be dimensioned based on the moment of inertia of the generating set. It is shown that the damper winding has optimal values to reach synchronous operation in the shortest period of time after transient operation. With optimal dimensioning, interferenceon the grid is minimized.

Direct torque control of permanent magnet synchronous machines - analysis and implementation

Thedirect torque control (DTC) has become an accepted vector control method besidethe current vector control. The DTC was first applied to asynchronous machines,and has later been applied also to synchronous machines. This thesis analyses the application of the DTC to permanent magnet synchronous machines (PMSM). In order to take the full advantage of the DTC, the PMSM has to be properly dimensioned. Therefore the effect of the motor parameters is analysed taking the control principle into account. Based on the analysis, a parameter selection procedure is presented. The analysis and the selection procedure utilize nonlinear optimization methods. The key element of a direct torque controlled drive is the estimation of the stator flux linkage. Different estimation methods - a combination of current and voltage models and improved integration methods - are analysed. The effect of an incorrect measured rotor angle in the current model is analysed andan error detection and compensation method is presented. The dynamic performance of an earlier presented sensorless flux estimation method is made better by improving the dynamic performance of the low-pass filter used and by adapting the correction of the flux linkage to torque changes. A method for the estimation ofthe initial angle of the rotor is presented. The method is based on measuring the inductance of the machine in several directions and fitting the measurements into a model. The model is nonlinear with respect to the rotor angle and therefore a nonlinear least squares optimization method is needed in the procedure. A commonly used current vector control scheme is the minimum current control. In the DTC the stator flux linkage reference is usually kept constant. Achieving the minimum current requires the control of the reference. An on-line method to perform the minimization of the current by controlling the stator flux linkage reference is presented. Also, the control of the reference above the base speed is considered. A new estimation flux linkage is introduced for the estimation of the parameters of the machine model. In order to utilize the flux linkage estimates in off-line parameter estimation, the integration methods are improved. An adaptive correction is used in the same way as in the estimation of the controller stator flux linkage. The presented parameter estimation methods are then used in aself-commissioning scheme. The proposed methods are tested with a laboratory drive, which consists of a commercial inverter hardware with a modified software and several prototype PMSMs.

Contact Center Functionality - Collecting and Prioritizing Features of Modern Contact Center.

Tässä diplomityössä pohditaan call centereiden asemaa tämän päivän palveluympäristössä ja myöskin call centereiden tulevaisuutta contact centereinä. Tämä työ tutkii kuinka asiakastarpeita ja uusia toiminnallisuuksia voidaan etsiä olemassaolevaan, mutta vielä keskeneräiseen call center tuotteeseen. Tutkimus on tehty lukemalla artikkeleita ja kirjoja tulevaisuuden contact centereistä, haastattelemalla asiakkaita ja järjestämällä ideointisessio yrityksen asiantuntijoille. Näin saadut tulokset priorisoitiin tätä tarkoitusta varten kehitellyllä matriisilla. Lopullisena tuloksena on lista toiminnallisuuksista tärkeysjärjestyksessä ja tuote roadmap kaikkein tärkeimmistä toiminnallisuuksista. Tämä roadmap antaa tuotekehitykselle ehdotuksen mitä tulisi implementoida nykyiseen tuotteeseen ja mitkä ovat prioriteetit. Tässä työssä pohdiskellaan myös tuotteen modulaarista rakennetta.

External Location Factors of Foreign Direct Investment in Russia – Finnish Perspective

Tämän diplomityön tavoitteena on selvittää, mitä alueellisia tekijöitä suomalaiset yritykset ottavat huomioon valitessaan sopivaa sijaintia suoralle investoinnille Venäjän sisällä. Muutamia yrityksen sisäisiä tekijöitä käytetään taustamuuttujina selittämään sijaintitekijöiden painotuksissa havaittavia eroja erilaisten yritysten välillä. Venäjän alueita vertaillaan lopuksi painotusten valossa. Työn ensimmäisessä osassa keskitytään suorien ulkomaisten investointien teoreettiseen taustaan. Aiempia tutkimuksia käydään läpi, jotta tekijät, joilla on havaittu olevan vaikutusta investointien sijoittumiseen maan sisällä, saadaan kartoitettua. Työn jälkimmäinen osa perustuu yrityskyselyn avulla kerättyyn empiiriseen aineistoon. Aineiston avulla selvitetään mitä tekijöitä suomalaisyritykset huomioivat sijaintipäätöstä tehdessään. Tulosten valossa on ilmeistä, että alueen markkinapotentiaali on suomalaisyrityksissä tärkein huomioitava tekijä investoinnin sijainnista päätettäessä. Myös infrastruktuuri ja kustannushyödyt vaikuttavat päätökseen. Erityyppisten yritysten painotukset ovat hyvin samanlaisia. Moskova ja Pietari vastaavat Venäjän alueista parhaiten suomalaisyritysten investoinnin sijainnille asettamia kriteerejä.

External Location Factors of Finnish Direct Investment in Central and Eastern European Transitional Economies

Tutkimuksen päätavoitteena oli selvittää suomalaisten suorien investointien maan valintaan vaikuttavia tekijöitä Itä- ja Keski-Euroopan kymmenessä siirtymätaloudessa. Empiirisessä osuudessa tarkasteltiin suomalaisten yritysten tärkeimpiä sijaintitekijöitä alueella ja yrityskohtaisten tekijöiden vaikutusta sijaintitekijöihin. Tutkimuksessa selvitettiin myös yritysten päämotiiveja investoida maihin. Laaditun investointikriteeristön mukaan maat pystyttiin laittamaan paremmuusjärjestykseen suomalaisen investoijan kannalta. Empiirisen osuuden aineisto kerättiin postikyselylomakkeella yrityksiltä, joilla on tai jotka ovat suunnittelemassa investointeja näihin maihin. Tutkimusote oli kvantitatiivinen. Tutkimustulokset osoittavat, että suomalaiset investoijat valitsevat Itä- ja Keski-Euroopan maan investointikohteeksi pääasiassa markkinapotentiaalin ja edullisten kustannusten perusteella. Myös infrastruktuuri vaikuttaa maan valintaan. Eri aloilla toimivien yritysten sijaintitekijöiden painotuksissa havaittiin eroja. Yrityksen koko ja päämotiivi vaikuttivat sijaintitekijöiden painotuksiin. Investointikriteereiden mukaan kaksi parasta investointimaata suomalaisille investoijille ovat Puola ja Viro. Vertailtaessa investointikriteereitä toteutuneisiin investointeihin voidaan todeta, että suomalaiset investoijat eivät ole hyödyntäneet investoinneilla saatavia etuja kaikissa kohdemaissa.

Sähköinen asiakaspalautetieto osana yrityksen tietopääomaa (knowledge management)

Sähköinen asiakaspalautetieto osana yrityksen tietopääomaaAsiakaspalaute osana yrityksen tietopääomaa mahdollistaa pysyvän kilpailuedun luomisen yritykselle. Kilpailuetua voidaan saavuttaa seuraavilla osa-alueilla: Asiakaspalautetiedon avulla yritys voi kehittää nykyisiä tuotteita ja/tai palveluita entistä asiakaslähtöisemmiksi. Uusien liiketoiminta-alueiden löytyminen on myös mahdollista asiakaspalautetiedon avulla. Sekä uusien liiketoimintojen että nykyisten liiketoimintojen osalta asiakaspalautetiedolla voidaan lisätä asiakasuskollisuutta ja sen avulla voidaan käynnistää asiakasdialogeja. Yrityksen hakiessa kilpailuetua asiakaspalautejärjestelmän avulla on kiinnitettävä huomiota nykyisen teorian tuottamaan kriteeristöön. Kriteeristöstä nousee esille seuraavat osa-alueet: asiakaspalautteen lähteet, asiakaspalautekanavat, asiakaspalautteen käsittelymenetelmät ja asiakaspalautteen prosessointi yrityksessä. Empiria antaa viitteitä siitä, että yrityksen kannattaa yhdistää suoranpalautteen järjestelmänsä ja asiakastyytyväisyysmittaaminen yhdeksi kokonaisuudeksi. Tämä kokonaisuus kannattaa toteuttaa sähköisesti ja yrityksen kannattaa käyttää sitä jatkuvasti.Sähköisen asiakaspalautejärjestelmän kerätessä palautteen antajien yhteystiedot on yrityksen mahdollista luoda uusi sähköinen media.

GPS-signal Source Based on Direct Digital Synthesis

This thesis presents the design and implementation of a GPS-signal source suitable for receiver measurements. The developed signal source is based on direct digital synthesis which generates the intermediate frequency. The intermediate frequency is transfered to the final frequency with the aid of an Inphase/Quadrature modulator. The modulating GPS-data was generated with MATLAB. The signal source was duplicated to form a multi channel source. It was shown that, GPS-signals ment for civil navigation are easy to generate in the laboratory. The hardware does not need to be technically advanced if navigation with high level of accuracy is not needed. It was also shown that, the Inphase/Quadrature modulator can function as a single side band upconverter even with a high intermediate frequency. This concept reduces the demands required for output filtering.