Improving the competitiveness of electrolytic Zinc process by chemical reaction engineering approach

This doctoral thesis describes the development work performed on the leachand purification sections in the electrolytic zinc plant in Kokkola to increase the efficiency in these two stages, and thus the competitiveness of the plant. Since metallic zinc is a typical bulk product, the improvement of the competitiveness of a plant was mostly an issue of decreasing unit costs. The problems in the leaching were low recovery of valuable metals from raw materials, and that the available technology offered complicated and expensive processes to overcome this problem. In the purification, the main problem was consumption of zinc powder - up to four to six times the stoichiometric demand. This reduced the capacity of the plant as this zinc is re-circulated through the electrolysis, which is the absolute bottleneck in a zinc plant. Low selectivity gave low-grade and low-value precipitates for further processing to metallic copper, cadmium, cobalt and nickel. Knowledge of the underlying chemistry was poor and process interruptions causing losses of zinc production were frequent. Studies on leaching comprised the kinetics of ferrite leaching and jarosite precipitation, as well as the stability of jarosite in acidic plant solutions. A breakthrough came with the finding that jarosite could precipitate under conditions where ferrite would leach satisfactorily. Based on this discovery, a one-step process for the treatment of ferrite was developed. In the plant, the new process almost doubled the recovery of zinc from ferrite in the same equipment as the two-step jarosite process was operated in at that time. In a later expansion of the plant, investment savings were substantial compared to other technologies available. In the solution purification, the key finding was that Co, Ni, and Cu formed specific arsenides in the “hot arsenic zinc dust” step. This was utilized for the development of a three-step purification stage based on fluidized bed technology in all three steps, i.e. removal of Cu, Co and Cd. Both precipitation rates and selectivity increased, which strongly decreased the zinc powder consumption through a substantially suppressed hydrogen gas evolution. Better selectivity improved the value of the precipitates: cadmium, which caused environmental problems in the copper smelter, was reduced from 1-3% reported normally down to 0.05 %, and a cobalt cake with 15 % Co was easily produced in laboratory experiments in the cobalt removal. The zinc powder consumption in the plant for a solution containing Cu, Co, Ni and Cd (1000, 25, 30 and 350 mg/l, respectively), was around 1.8 g/l; i.e. only 1.4 times the stoichiometric demand – or, about 60% saving in powder consumption. Two processes for direct leaching of the concentrate under atmospheric conditions were developed, one of which was implemented in the Kokkola zinc plant. Compared to the existing pressure leach technology, savings were obtained mostly in investment. The scientific basis for the most important processes and process improvements is given in the doctoral thesis. This includes mathematical modeling and thermodynamic evaluation of experimental results and hypotheses developed. Five of the processes developed in this research and development program were implemented in the plant and are still operated. Even though these processes were developed with the focus on the plant in Kokkola, they can also be implemented at low cost in most of the zinc plants globally, and have thus a great significance in the development of the electrolytic zinc process in general.

Computational studies for the design of process equipment with complex geometries

This study combines several projects related to the flows in vessels with complex shapes representing different chemical apparata. Three major cases were studied. The first one is a two-phase plate reactor with a complex structure of intersecting micro channels engraved on one plate which is covered by another plain plate. The second case is a tubular microreactor, consisting of two subcases. The first subcase is a multi-channel two-component commercial micromixer (slit interdigital) used to mix two liquid reagents before they enter the reactor. The second subcase is a micro-tube, where the distribution of the heat generated by the reaction was studied. The third case is a conventionally packed column. However, flow, reactions or mass transfer were not modeled. Instead, the research focused on how to describe mathematically the realistic geometry of the column packing, which is rather random and can not be created using conventional computeraided design or engineering (CAD/CAE) methods. Several modeling approaches were used to describe the performance of the processes in the considered vessels. Computational fluid dynamics (CFD) was used to describe the details of the flow in the plate microreactor and micromixer. A space-averaged mass transfer model based on Fick’s law was used to describe the exchange of the species through the gas-liquid interface in the microreactor. This model utilized data, namely the values of the interfacial area, obtained by the corresponding CFD model. A common heat transfer model was used to find the heat distribution in the micro-tube. To generate the column packing, an additional multibody dynamic model was implemented. Auxiliary simulation was carried out to determine the position and orientation of every packing element in the column. This data was then exported into a CAD system to generate desirable geometry, which could further be used for CFD simulations. The results demonstrated that the CFD model of the microreactor could predict the flow pattern well enough and agreed with experiments. The mass transfer model allowed to estimate the mass transfer coefficient. Modeling for the second case showed that the flow in the micromixer and the heat transfer in the tube could be excluded from the larger model which describes the chemical kinetics in the reactor. Results of the third case demonstrated that the auxiliary simulation could successfully generate complex random packing not only for the column but also for other similar cases.

Characterization Of Process Efficiency Improvement In Laser Additive Manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, has gained a lot of interest in past recent years within various industries, such as medical and aerospace industries. LAM enables fabrication of complex 3D geometries by melting metal powder layer by layer with laser beam. Research in laser additive manufacturing has been focused in development of new materials and new applications in past 10 years. Since this technology is on cutting edge, efficiency of manufacturing process is in center role of research of this industry. Aim of this thesis is to characterize methods for process efficiency improvements in laser additive manufacturing. The aim is also to clarify the effect of process parameters to the stability of the process and in microstructure of manufactured pieces. Experimental tests of this thesis were made with various process parameters and their effect on build pieces has been studied, when additive manufacturing was performed with a modified research machine representing EOSINT M-series and with EOS EOSINT M280. Material used was stainless steel 17-4 PH. Also, some of the methods for process efficiency improvements were tested. Literature review of this thesis presents basics of laser additive manufacturing, methods for improve the process efficiency and laser beam – material- interaction. It was observed that there are only few public studies about process efficiency of laser additive manufacturing of stainless steel. According to literature, it is possible to improve process efficiency with higher power lasers and thicker layer thicknesses. The process efficiency improvement is possible if the effect of process parameter changes in manufactured pieces is known. According to experiments carried out in this thesis, it was concluded that process parameters have major role in single track formation in laser additive manufacturing. Rough estimation equations were created to describe the effect of input parameters to output parameters. The experimental results showed that the WDA (width-depth-area of cross-sections of single track) is correlating exponentially with energy density input. The energy density input is combination of the input parameters of laser power, laser beam spot diameter and scan speed. The use of skin-core technique enables improvement of process efficiency as the core of the part is manufactured with higher laser power and thicker layer thickness and the skin with lower laser power and thinner layer thickness in order to maintain high resolution. In this technique the interface between skin and core must have overlapping in order to achieve full dense parts. It was also noticed in this thesis that keyhole can be formed in LAM process. It was noticed that the threshold intensity value of 106 W/cm2 was exceeded during the tests. This means that in these tests the keyhole formation was possible.

Upconverting diagnostics: Multiplex assays utilizing upconversion luminescence technology

Conventional diagnostics tests and technologies typically allow only a single analysis and result per test. The aim of this study was to propose robust and multiplex array-inwell test platforms based on oligonucleotide and protein arrays combining the advantages of simple instrumentation and upconverting phosphor (UCP) reporter technology. The UCPs are luminescent lanthanide-doped crystals that have a unique capability to convert infrared radiation into visible light. No autofluorescence is produced from the sample under infrared excitation enabling the development of highly sensitive assays. In this study, an oligonucleotide array-in-well hybridization assay was developed for the detection and genotyping of human adenoviruses. The study provided a verification of the advantages and potential of the UCP-based reporter technology in multiplex assays as well as anti-Stokes photoluminescence detection with a new anti- Stokes photoluminescence imager. The developed assay was technically improved and used to detect and genotype adenovirus types from clinical specimens. Based on the results of the epidemiological study, an outbreak of adenovirus type B03 was observed in the autumn of 2010. A quantitative array-in-well immunoassay was developed for three target analytes (prostate specific antigen, thyroid stimulating hormone, and luteinizing hormone). In this study, quantitative results were obtained for each analyte and the analytical sensitivities in buffer were in clinically relevant range. Another protein-based array-inwell assay was developed for multiplex serodiagnostics. The developed assay was able to detect parvovirus B19 IgG and adenovirus IgG antibodies simultaneously from serum samples according to reference assays. The study demonstrated that the UCPtechnology is a robust detection method for diverse multiplex imaging-based array-inwell assays.

Russian SME technology transfer to Finland – Entrepreneurial challenges and motivation

The purpose of this thesis is to study the international technology transfer of transition economy SME entrepreneurs to the developed countries. The research aims to characterize the phenomenon by studying Russian SME technology transfer to Finland with the research methods from case studies. In addition to characterizing the phenomenon, the research finds out factors that motivate Russian entrepreneurs to conduct international technology transfer and what are the challenges the Russian entrepreneurs face when they enter the Finnish business environment. The qualitative data was collected from six semi-structured interviews with the entrepreneurs and several secondary data sources, considering four different technology transfer cases. The data and the analysis showed that the case companies in Finland are mostly linked to manufacturing of physical products. The entrepreneurs are motivated to come to Finland mainly by the opportunities and support the Finnish business and innovation environment provides to the entrepreneurs and by the personal gain that they get by establishing the company in Finland. Major challenges in the process include time constraints and capital requirements, difficulties on achieving sales on the Finnish market and finding skilled personnel to support the Russian management and owners.

Novel technology for preparation of optically active chemicals

Asymmetric synthesis using modified heterogeneous catalysts has gained lots of interest in the production of optically pure chemicals, such as pharmaceuticals, nutraceuticals, fragrances and agrochemicals. Heterogeneous modified catalysts capable of inducing high enantioselectivities are preferred in industrial scale due to their superior separation and handling properties. The topic has been intensively investigated both in industry and academia. The enantioselective hydrogenation of ethyl benzoylformate (EBF) to (R)-ethyl mandelate over (-)-cinchonidine (CD)-modified Pt/Al2O3 catalyst in a laboratory-scale semi-batch reactor was studied as a function of modifier concentration, reaction temperature, stirring rate and catalyst particle size. The main product was always (R)-ethyl mandelate while small amounts of (S)-ethyl mandelate were obtained as by product. The kinetic results showed higher enantioselectivity and lower initial rates approaching asymptotically to a constant value as the amount of modifier was increased. Additionally, catalyst deactivation due to presence of impurities in the feed was prominent in some cases; therefore activated carbon was used as a cleaning agent of the raw material to remove impurities prior to catalyst addition. Detailed characterizations methods (SEM, EDX, TPR, BET, chemisorption, particle size distribution) of the catalysts were carried out. Solvent effects were also studied in the semi-batch reactor. Solvents with dielectric constant (e) between 2 and 25 were applied. The enantiomeric excess (ee) increased with an increase of the dielectric coefficient up to a maximum followed by a nonlinear decrease. A kinetic model was proposed for the enantioselectivity dependence on the dielectric constant based on the Kirkwood treatment. The non-linear dependence of ee on (e) successfully described the variation of ee in different solvents. Systematic kinetic experiments were carried out in the semi-batch reactor. Toluene was used as a solvent. Based on these results, a kinetic model based on the assumption of different number of sites was developed. Density functional theory calculations were applied to study the energetics of the EBF adsorption on pure Pt(1 1 1). The hydrogenation rate constants were determined along with the adsorption parameters by non-linear regression analysis. A comparison between the model and the experimental data revealed a very good correspondence. Transient experiments in a fixed-bed reactor were also carried out in this work. The results demonstrated that continuous enantioselective hydrogenation of EBF in hexane/2-propanol 90/10 (v/v) is possible and that continuous feeding of (-)-cinchonidine is needed to maintain a high steady-state enantioselectivity. The catalyst showed a good stability and high enantioselectivity was achieved in the fixed-bed reactor. Chromatographic separation of (R)- and (S)-ethyl mandelate originating from the continuous reactor was investigated. A commercial column filled with a chiral resin was chosen as a perspective preparative-scale adsorbent. Since the adsorption equilibrium isotherms were linear within the entire investigated range of concentrations, they were determined by pulse experiments for the isomers present in a post-reaction mixture. Breakthrough curves were measured and described successfully by the dispersive plug flow model with a linear driving force approximation. The focus of this research project was the development of a new integrated production concept of optically active chemicals by combining heterogeneous catalysis and chromatographic separation technology. The proposed work is fundamental research in advanced process technology aiming to improve efficiency and enable clean and environmentally benign production of enantiomeric pure chemicals.

On-line determination of residual collector concentration in flotation process

Valuable minerals can be recovered by using froth flotation. This is a widely used separation technique in mineral processing. In a flotation cell hydrophobic particles attach on air bubbles dispersed in the slurry and rise on the top of the cell. Valuable particles are made hydrophobic by adding collector chemicals in the slurry. With the help of a frother reagent a stable froth forms on the top of the cell and the froth with valuable minerals, i.e. the concentrate, can be removed for further processing. Normally the collector is dosed on the basis of the feed rate of the flotation circuit and the head grade of the valuable metal. However, also the mineral composition of the ore affects the consumption of the collector, i.e. how much is adsorbed on the mineral surfaces. Therefore it is worth monitoring the residual collector concentration in the flotation tailings. Excess usage of collector causes unnecessary costs and may even disturb the process. In the literature part of the Master’s thesis the basics of flotation process and collector chemicals are introduced. Capillary electrophoresis (CE), an analytical technique suitable for detecting collector chemicals, is also reviewed. In the experimental part of the thesis the development of an on-line CE method for monitoring the concentration of collector chemicals in a flotation process and the results of a measurement campaign are presented. It was possible to determine the quality and quantity of collector chemicals in nickel flotation tailings at a concentrator plant with the developed on-line CE method. Sodium ethyl xanthate and sodium isopropyl xanthate residuals were found in the tailings and slight correlation between the measured concentrations and the dosage amounts could be seen.

ORCiD – Membership and implementation at Chalmers University of Technology

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Feasibility study of submerged membrane bioreactor (MBR) as an alternative to conventional activated sludge process (CASP) for municipal wastewater treatment: A pilot scale study

The conventional activated sludge processes (CAS) for the treatment of municipal wastewater are going to be outdated gradually due to more stringent environmental protection laws and regulations. The Membrane bioreactors (MBRs) are the most promising modern technology widely accepted in the world of wastewater treatment due to their highly pronounced features such as high quality effluent, less foot print and working under high MLSS concentration. This research project was carried out to investigate the feasibility and effectiveness of MBR technology compare to the CAS process based on the scientific facts and results. The pilot scale MBR pilot plant was run for more than 150 days and the analysis results were evaluated. The prime focus of the project was to evaluate the correlation of permeate flux under different operating MLSS concentrations. The permeate flux was found almost constant regardless of variations in MLSS concentrations. The removal of micropollutant such as heavy metals, PCPPs, PFCs, steroidal hormones was also studied. The micropollutant removal performance of MBR process was found relatively effective than CAS process. Furthermore, the compatibility of submerged membranes within the bioreactor had truly reduced the process footprint.

Susteinable steelmaking by process integration

Environmental issues, including global warming, have been serious challenges realized worldwide, and they have become particularly important for the iron and steel manufacturers during the last decades. Many sites has been shut down in developed countries due to environmental regulation and pollution prevention while a large number of production plants have been established in developing countries which has changed the economy of this business. Sustainable development is a concept, which today affects economic growth, environmental protection, and social progress in setting up the basis for future ecosystem. A sustainable headway may attempt to preserve natural resources, recycle and reuse materials, prevent pollution, enhance yield and increase profitability. To achieve these objectives numerous alternatives should be examined in the sustainable process design. Conventional engineering work cannot address all of these substitutes effectively and efficiently to find an optimal route of processing. A systematic framework is needed as a tool to guide designers to make decisions based on overall concepts of the system, identifying the key bottlenecks and opportunities, which lead to an optimal design and operation of the systems. Since the 1980s, researchers have made big efforts to develop tools for what today is referred to as Process Integration. Advanced mathematics has been used in simulation models to evaluate various available alternatives considering physical, economic and environmental constraints. Improvements on feed material and operation, competitive energy market, environmental restrictions and the role of Nordic steelworks as energy supplier (electricity and district heat) make a great motivation behind integration among industries toward more sustainable operation, which could increase the overall energy efficiency and decrease environmental impacts. In this study, through different steps a model is developed for primary steelmaking, with the Finnish steel sector as a reference, to evaluate future operation concepts of a steelmaking site regarding sustainability. The research started by potential study on increasing energy efficiency and carbon dioxide reduction due to integration of steelworks with chemical plants for possible utilization of available off-gases in the system as chemical products. These off-gases from blast furnace, basic oxygen furnace and coke oven furnace are mainly contained of carbon monoxide, carbon dioxide, hydrogen, nitrogen and partially methane (in coke oven gas) and have proportionally low heating value but are currently used as fuel within these industries. Nonlinear optimization technique is used to assess integration with methanol plant under novel blast furnace technologies and (partially) substitution of coal with other reducing agents and fuels such as heavy oil, natural gas and biomass in the system. Technical aspect of integration and its effect on blast furnace operation regardless of capital expenditure of new operational units are studied to evaluate feasibility of the idea behind the research. Later on the concept of polygeneration system added and a superstructure generated with alternative routes for off-gases pretreatment and further utilization on a polygeneration system producing electricity, district heat and methanol. (Vacuum) pressure swing adsorption, membrane technology and chemical absorption for gas separation; partial oxidation, carbon dioxide and steam methane reforming for methane gasification; gas and liquid phase methanol synthesis are the main alternative process units considered in the superstructure. Due to high degree of integration in process synthesis, and optimization techniques, equation oriented modeling is chosen as an alternative and effective strategy to previous sequential modelling for process analysis to investigate suggested superstructure. A mixed integer nonlinear programming is developed to study behavior of the integrated system under different economic and environmental scenarios. Net present value and specific carbon dioxide emission is taken to compare economic and environmental aspects of integrated system respectively for different fuel systems, alternative blast furnace reductants, implementation of new blast furnace technologies, and carbon dioxide emission penalties. Sensitivity analysis, carbon distribution and the effect of external seasonal energy demand is investigated with different optimization techniques. This tool can provide useful information concerning techno-environmental and economic aspects for decision-making and estimate optimal operational condition of current and future primary steelmaking under alternative scenarios. The results of the work have demonstrated that it is possible in the future to develop steelmaking towards more sustainable operation.

Integrating Use of Customer Information Throughout Multiple Sales Channels to Create Customer Competence

Customer knowledge management (CKM) practices enable organizations to create customer competence with systematic use of customer information that is integrated throughout the organization. Nonetheless, organizations are not able to fully exploit the vast amount of data available. Previous research on use of customer information is limited especially in a multichannel environment. The aim of this study was to identify the main obstacles for utilizing customer information efficiently across multiple sales channels. The study was conducted as a single case study in order to gain deeper understanding of the research problem. The empirical findings indicate that lack of CKM practices and a common goal are major challenges obstructing effective utilization of customer information. Furthermore, decentralized organizational structure and insufficient analytical skills create obstacles for information sharing and capabilities to process information and create new knowledge. The implications of the study suggest that in order to create customer competence organizations should shift their focus from technology to the organizational factors affecting use of information and implement CKM practices throughout the organization.

Improving the usability of extruded wood-plastic composites by using modification technology

Using cellulosic reinforcement to produce plastic composites is a globally growing trend. One of such materials are wood-plastic composites, which are an extensively studied group of materials for which the global industry is looking for new applications. Issues such as bondability, durability and fire resistance still require development to improve the usability of the wood-plastic composite material. Improvement of the usability of wood-plastic composites is studied in this thesis through the effects of using selected modification technology in wood and plastic industry. The applied modification methods are surface by mechanical abrasion and plasma, chemical impregnation of wood flour, and structural modification by the co-extrusion process. The study shows that the properties of WPC can be influenced by the selected modification methods. The selected methods are also found to be able to result as improvement in the properties of the material. The may also affect other than just the targeted properties of the end-product, either in a positive or a negative manner. Therefore modification as performance improvement should be considered as a caseby- case study. Introducing WPC materials for new applications can be done by using modification technology. Structuralmodification can possibly be used to reduce material costs of the modified WPC material.

Trukkitraktorin rungon suunnittelu ja laskenta

Tässä työssä suunniteltiin lappeenrantalaisen Astex Oy:n tilauksesta liikkuvan työkoneen runkorakenne. Työ tehtiin Lappeenrannan teknillisen yliopiston teräsrakenteiden laboratoriossa. Suunniteltava rakenne kuului linkkuohjattuun, noin 5000 kg painoiseen trukkitraktoriin. Lähtökohtana rakenteen suunnittelulle olivat tilaajan asettamat rakenteen geometriaan ja suorituskykyyn liittyvät reunaehdot ja rajoitteet. Uuden rakenteen suunnittelussa hyödynnettiin myös tilaajatahon kehittelemää vastaavan tyyppistä prototyyppirakennetta. Rakenteen suunnitteluprosessi koostui neljästä eri vaiheesta. Suunniteltavan rakenteen lähtökohtana olleelle prototyyppirakenteelle suoritettiin koneen käytönaikaisia venymäliuskamittauksia rakenteen kuormitushistorian selvittämiseksi. Mittauksista saatujen tulosten perusteella määritettiin kuormitukset uudelle suunniteltavalle rakenteelle. Määritettyjä kuormituksia hyödyntäen ideoitiin, suunniteltiin ja mallinnettiin uusi tilaajan vaatimuksia vastaava rakenne. Uudelle rakenteelle suoritettiin lujuusanalyysit FE-analyysiä hyödyntäen. Uuden rakenteen suunnittelussa kiinnitettiin huomiota rakenteen hyvään valmistettavuuteen ja suunniteltiin rakenneratkaisut tilaajataholle mahdollisimman optimaalisiksi. Suunnittelu- ja mallinnustyö tehtiin Solidworks 2014 ohjelmistolla. Rakenteen lujuustekniset tarkastelut sisälsivät rakennedetaljien analyyttistä mitoitusta ja laskentaa. FE-laskennalla selvitettiin rakenteen ääri- ja väsymiskestävyys. Laskenta sisälsi koko rakenteen globaaleja tarkasteluja, sekä eri kriittisten rakennedetaljien yksityiskohtaisempia analyysejä. FE-laskennan pääpaino oli rakenteen väsymisanalyyseissä, jotka toteutettiin Hot-Spot- ja särönkasvumenetelmillä. Rakenteen FE-analyysien suorittamisessa käytettiin Femap, NxNastran ja Abaqus-ohjelmistoja.

Learning information technology business in a changing industry landscape. Introducing Team Entrepreneurship in Renewing Bachelor Education in Renewing Bachelor Education in Information

Speed, uncertainty and complexity are increasing in the business world all the time. When knowledge and skills become quickly irrelevant, new challenges are set for information technology (IT) education. Meta-learning skills – learning how to learn rapidly - and innovation skills have become more essential than single technologies or other specific issues. The drastic changes in the information and communications technology (ICT) sector have caused a need to reconsider how IT Bachelor education in Universities of Applied Sciences should be organized and employed to cope with the change. The objective of the study was to evaluate how a new approach to IT Bachelor education, the ICT entrepreneurship study path (ICT-ESP) fits IT Bachelor education in a Finnish University of Applied Sciences. This kind of educational arrangement has not been employed elsewhere in the context of IT Bachelor education. The study presents the results of a four-year period during which IT Bachelor education was renewed in a Finnish University of Applied Sciences. The learning environment was organized into an ICT-ESP based on Nonaka’s knowledge theory and Kolb’s experiental learning. The IT students who studied in the ICT-ESP established a cooperative and learned ICT by running their cooperative at the University of Applied Sciences. The students (called team entrepreneurs) studied by reading theory in books and other sources of explicit information, doing projects for their customers, and reflecting in training sessions on what was learnt by doing and by studying the literature. Action research was used as the research strategy in this study. Empirical data was collected via theme-based interviews, direct observation, and participative observation. Grounded theory method was utilized in the data analysis and the theoretical sampling was used to guide the data collection. The context of the University of Applied Sciences provided a good basis for fostering team entrepreneurship. However, the results showed that the employment of the ICT-ESP did not fit into the IT Bachelor education well enough. The ICT-ESP was cognitively too tough for the team entrepreneurs because they had two different set of rules to follow in their studies. The conventional courses engaged lot of energy which should have been spent for professional development in the ICT-ESP. The amount of competencies needed in the ICT-ESP for professional development was greater than those needed for any other ways of studying. The team entrepreneurs needed to develop skills in ICT, leadership and self-leadership, team development and entrepreneurship skills. The entrepreneurship skills included skills on marketing and sales, brand development, productization, and business administration. Considering the three-year time the team entrepreneurs spent in the ICT-ESP, the challenges were remarkable. Changes to the organization of IT Bachelor education are also suggested in the study. At first, it should be admitted that the ICT-ESP produces IT Bachelors with a different set of competencies compared to the conventional way of educating IT Bachelors. Secondly, the number of courses on general topics in mathematics, physics, and languages for team entrepreneurs studying in the ICTESP should be reconsidered and the conventional course-based teaching of the topics should be reorganized to support the team coaching process of the team entrepreneurs with their practiceoriented projects. Third, the upcoming team entrepreneurs should be equipped with relevant information about the ICT-ESP and what it would require in practice to study as a team entrepreneur. Finally, the upcoming team entrepreneurs should be carefully selected before they start in the ICT-ESP to have a possibility to eliminate solo players and those who have a too romantic view of being a team entrepreneur. The results gained in the study provided answers to the original research questions and the objectives of the study were met. Even though the IT degree programme was terminated during the research process, the amount of qualitative data gathered made it possible to justify the interpretations done.

Stiffness based trajectory planning and feedforward based vibration suppression control of parallel robot machines

The dissertation proposes two control strategies, which include the trajectory planning and vibration suppression, for a kinematic redundant serial-parallel robot machine, with the aim of attaining the satisfactory machining performance. For a given prescribed trajectory of the robot's end-effector in the Cartesian space, a set of trajectories in the robot's joint space are generated based on the best stiffness performance of the robot along the prescribed trajectory. To construct the required system-wide analytical stiffness model for the serial-parallel robot machine, a variant of the virtual joint method (VJM) is proposed in the dissertation. The modified method is an evolution of Gosselin's lumped model that can account for the deformations of a flexible link in more directions. The effectiveness of this VJM variant is validated by comparing the computed stiffness results of a flexible link with the those of a matrix structural analysis (MSA) method. The comparison shows that the numerical results from both methods on an individual flexible beam are almost identical, which, in some sense, provides mutual validation. The most prominent advantage of the presented VJM variant compared with the MSA method is that it can be applied in a flexible structure system with complicated kinematics formed in terms of flexible serial links and joints. Moreover, by combining the VJM variant and the virtual work principle, a systemwide analytical stiffness model can be easily obtained for mechanisms with both serial kinematics and parallel kinematics. In the dissertation, a system-wide stiffness model of a kinematic redundant serial-parallel robot machine is constructed based on integration of the VJM variant and the virtual work principle. Numerical results of its stiffness performance are reported. For a kinematic redundant robot, to generate a set of feasible joints' trajectories for a prescribed trajectory of its end-effector, its system-wide stiffness performance is taken as the constraint in the joints trajectory planning in the dissertation. For a prescribed location of the end-effector, the robot permits an infinite number of inverse solutions, which consequently yields infinite kinds of stiffness performance. Therefore, a differential evolution (DE) algorithm in which the positions of redundant joints in the kinematics are taken as input variables was employed to search for the best stiffness performance of the robot. Numerical results of the generated joint trajectories are given for a kinematic redundant serial-parallel robot machine, IWR (Intersector Welding/Cutting Robot), when a particular trajectory of its end-effector has been prescribed. The numerical results show that the joint trajectories generated based on the stiffness optimization are feasible for realization in the control system since they are acceptably smooth. The results imply that the stiffness performance of the robot machine deviates smoothly with respect to the kinematic configuration in the adjacent domain of its best stiffness performance. To suppress the vibration of the robot machine due to varying cutting force during the machining process, this dissertation proposed a feedforward control strategy, which is constructed based on the derived inverse dynamics model of target system. The effectiveness of applying such a feedforward control in the vibration suppression has been validated in a parallel manipulator in the software environment. The experimental study of such a feedforward control has also been included in the dissertation. The difficulties of modelling the actual system due to the unknown components in its dynamics is noticed. As a solution, a back propagation (BP) neural network is proposed for identification of the unknown components of the dynamics model of the target system. To train such a BP neural network, a modified Levenberg-Marquardt algorithm that can utilize an experimental input-output data set of the entire dynamic system is introduced in the dissertation. Validation of the BP neural network and the modified Levenberg- Marquardt algorithm is done, respectively, by a sinusoidal output approximation, a second order system parameters estimation, and a friction model estimation of a parallel manipulator, which represent three different application aspects of this method.