Determining vehicle drivetrain dynamics using system identification

Target of this book is to propose an approach for modelling drivetrain dynamics in order to design further a vibration control system of a hybrid bus. In this thesis two approaches are examined and compared. First model is obtained by theoretical means: drivetrain is represented as a system of rotating masses, which motion is described with differential equations. Second model is obtained using system identification method: mathematical description of the dynamic behavior of a system is formed based on measured input (torque) and output (speed) data. Then two models are compared and an optimal approach is suggested.

Analysis of Phase Separator Design Criteria Using Computational Fluid Dynamics

Gravitational phase separation is a common unit operation found in most large-scale chemical processes. The need for phase separation can arise e.g. from product purification or protection of downstream equipment. In gravitational phase separation, the phases separate without the application of an external force. This is achieved in vessels where the flow velocity is lowered substantially compared to pipe flow. If the velocity is low enough, the denser phase settles towards the bottom of the vessel while the lighter phase rises. To find optimal configurations for gravitational phase separator vessels, several different geometrical and internal design features were evaluated based on simulations using OpenFOAM computational fluid dynamics (CFD) software. The studied features included inlet distributors, vessel dimensions, demister configurations and gas phase outlet configurations. Simulations were conducted as single phase steady state calculations. For comparison, additional simulations were performed as dynamic single and two-phase calculations. The steady state single phase calculations provided indications on preferred configurations for most above mentioned features. The results of the dynamic simulations supported the utilization of the computationally faster steady state model as a practical engineering tool. However, the two-phase model provides more truthful results especially with flows where a single phase does not determine the flow characteristics.

Studies of rotor dynamics using a multibody simulation approach

The non-idealities in a rotor-bearing system may cause undesirable subcritical superharmonic resonances that occur when the rotating speed of the rotor is a fraction of the natural frequency of the system. These resonances arise partly from the non-idealities of the bearings. This study introduces a novel simulation approach that can be used to study the superharmonic vibrations of rotor-bearing systems. The superharmonic vibrations of complex rotor-bearing systems can be studied in an accurate manner by combining a detailed rotor and bearing model in a multibody simulation approach. The research looks at the theoretical background of multibody formulations that can be used in the dynamic analysis of flexible rotors. The multibody formulations currently in use are suitable for linear deformation analysis only. However, nonlinear formulation may arise in high-speed rotor dynamics applications due to the cenrrifugal stiffening effect. For this reason, finite element formulations that can describe nonlinear deformation are also introduced in this work. The description of the elastic forces in the absolute nodal coordinate formulation is studied and improved. A ball bearing model that includes localized and distributed defects is developed in this study. This bearing model could be used in rotor dynamics or multibody code as an interface elements between the rotor and the supporting structure. The model includes descriptions of the nonlinear Hertzian contact deformation and the elastohydrodynamic fluid film. The simulation approaches and models developed here are applied in the analysis of two example rotor-bearing systems. The first example is an electric motor supported by two ball bearings and the second is a roller test rig that consists of the tube roll of a paper machine supported by a hard-bearing-type balanceing machine. The simulation results are compared to the results available in literature as well as to those obtained by measuring the existing structure. In both practical examples, the comparison shows that the simulation model is capable of predicting the realistic responses of a rotor system. The simulation approaches developed in this work can be used in the analysis of the superharmonic vibrations of general rotor-bearing systems.

Models to study intermediate filament dynamics and functions

Intermediate filaments are part of the cytoskeleton and nucleoskeleton; they provide cells with structure and have important roles in cell signalling. The IFs are a large protein family with more than 70 members; each tightly regulated and expressed in a cell type-specific manner. Although the IFs have been known and studied for decades, our knowledge about their specific functions is still limited, despite the fact that mutations in IF genes cause numerous severe human diseases. In this work, three IF proteins are examined more closely; the nuclear lamin A/C and the cytoplasmic nestin and vimentin. In particular the regulation of lamin A/C dynamics, the role of nestin in muscle and body homeostasis as well as the functions and evolutionary aspects of vimentin are investigated. Together this data highlights some less well understood functions of these IFs. We used mass-spectrometry to identify inter-phase specific phosphorylation sites on lamin A. With the use of genetically engineered lamin A protein in combination with high resolution microscopy and biochemical methods we discovered novel roles for this phosphorylation in regulation of lamin dynamics. More specifically, our data suggests that the phosphorylation of certain amino acids in lamin A determines the localization and dynamics of the protein. In addition, we present results demonstrating that lamin A regulates Cdk5-activity. In the second study we use mice lacking nestin to gain more knowledge of this seldom studied protein. Our results show that nestin is essential for muscle regeneration; mice lacking nestin recover more slowly from muscle injury and show signs of spontaneous muscle regeneration, indicating that their muscles are more sensitive to stresses and injury. The absence of nestin also leads to decreased over-all muscle mass and slower body growth. Furthermore, nestin has a role in controlling testicle homeostasis as nestin-/- male mice show a greater variation in testicle size. The common fruit fly Drosophila melanogaster lacks cytoplasmic IFs as most insects do. By creating a fly that expresses human vimentin we establish a new research platform for vimentin studies, as well as provide a new tool for the studies of IF evolution.

Computational Market Dynamics of Virtual Economies

The last two decades have provided a vast opportunity to live and explore the compulsive imaginary world or virtual world through massively multiplayer online role-playing games (MMORPGs). MMORPG gives a wide range of opportunities to its users to participate with multi-players on the same platform, to communicate and to do real time actions. There is a virtual economy in these games which is largely player-driven. In-game currency provides its users to build up their Avatars, to buy or sell the necessary goods to play, survive in the games and so on. As a part of virtual economies generated through EVE Online, this thesis mainly focuses on how the prices of the minerals in EVE Online behave by applying the Jabłonska- Capasso-Morale (JCM) mathematical simulation model. It is to verify up to what degree the model can reproduce the virtual economy behavior. The model is applied to buy and sell prices of two minerals namely, isogen and morphite. The simulation results demonstrate that JCM model ts reasonably well to the mineral prices, which lets us conclude that virtual economies behave similarly to the real ones.

Real-time simulation of multibody systems with applications for working mobile vehicles

This dissertation describes an approach for developing a real-time simulation for working mobile vehicles based on multibody modeling. The use of multibody modeling allows comprehensive description of the constrained motion of the mechanical systems involved and permits real-time solving of the equations of motion. By carefully selecting the multibody formulation method to be used, it is possible to increase the accuracy of the multibody model while at the same time solving equations of motion in real-time. In this study, a multibody procedure based on semi-recursive and augmented Lagrangian methods for real-time dynamic simulation application is studied in detail. In the semirecursive approach, a velocity transformation matrix is introduced to describe the dependent coordinates into relative (joint) coordinates, which reduces the size of the generalized coordinates. The augmented Lagrangian method is based on usage of global coordinates and, in that method, constraints are accounted using an iterative process. A multibody system can be modelled as either rigid or flexible bodies. When using flexible bodies, the system can be described using a floating frame of reference formulation. In this method, the deformation mode needed can be obtained from the finite element model. As the finite element model typically involves large number of degrees of freedom, reduced number of deformation modes can be obtained by employing model order reduction method such as Guyan reduction, Craig-Bampton method and Krylov subspace as shown in this study The constrained motion of the working mobile vehicles is actuated by the force from the hydraulic actuator. In this study, the hydraulic system is modeled using lumped fluid theory, in which the hydraulic circuit is divided into volumes. In this approach, the pressure wave propagation in the hoses and pipes is neglected. The contact modeling is divided into two stages: contact detection and contact response. Contact detection determines when and where the contact occurs, and contact response provides the force acting at the collision point. The friction between tire and ground is modelled using the LuGre friction model, which describes the frictional force between two surfaces. Typically, the equations of motion are solved in the full matrices format, where the sparsity of the matrices is not considered. Increasing the number of bodies and constraint equations leads to the system matrices becoming large and sparse in structure. To increase the computational efficiency, a technique for solution of sparse matrices is proposed in this dissertation and its implementation demonstrated. To assess the computing efficiency, augmented Lagrangian and semi-recursive methods are implemented employing a sparse matrix technique. From the numerical example, the results show that the proposed approach is applicable and produced appropriate results within the real-time period.

Parameter estimation for Chaotic or Stochastic Dynamics

Since its discovery, chaos has been a very interesting and challenging topic of research. Many great minds spent their entire lives trying to give some rules to it. Nowadays, thanks to the research of last century and the advent of computers, it is possible to predict chaotic phenomena of nature for a certain limited amount of time. The aim of this study is to present a recently discovered method for the parameter estimation of the chaotic dynamical system models via the correlation integral likelihood, and give some hints for a more optimized use of it, together with a possible application to the industry. The main part of our study concerned two chaotic attractors whose general behaviour is diff erent, in order to capture eventual di fferences in the results. In the various simulations that we performed, the initial conditions have been changed in a quite exhaustive way. The results obtained show that, under certain conditions, this method works very well in all the case. In particular, it came out that the most important aspect is to be very careful while creating the training set and the empirical likelihood, since a lack of information in this part of the procedure leads to low quality results.

Stochastic particle models: mean reversion and burgers dynamics. An application to commodity markets

The aim of this study is to propose a stochastic model for commodity markets linked with the Burgers equation from fluid dynamics. We construct a stochastic particles method for commodity markets, in which particles represent market participants. A discontinuity in the model is included through an interacting kernel equal to the Heaviside function and its link with the Burgers equation is given. The Burgers equation and the connection of this model with stochastic differential equations are also studied. Further, based on the law of large numbers, we prove the convergence, for large N, of a system of stochastic differential equations describing the evolution of the prices of N traders to a deterministic partial differential equation of Burgers type. Numerical experiments highlight the success of the new proposal in modeling some commodity markets, and this is confirmed by the ability of the model to reproduce price spikes when their effects occur in a sufficiently long period of time.

Geographical Studies of Underwater Light Dynamics in the Coastal Archipelago of SW Finland, Baltic Sea

The underwater light field is an important environmental variable as it, among other things, enables aquatic primary production. Although the portion of solar radiation that is referred to as visible light penetrates water, it is restricted to a limited surface water layer because of efficient absorption and scattering processes. Based on the varying content of optical constituents in the water, the efficiency of light attenuation changes in many dimensions and over various spatial and temporal scales. This thesis discusses the underwater light dynamics of a transitional coastal archipelago in south-western Finland, in the Baltic Sea. While the area has long been known to have a highly variable underwater light field, quantified knowledge on the phenomenon has been scarce, patchy, or non-existent. This thesis focuses on the variability in the underwater light field through euphotic depths (1% irradiance remaining), which were derived from in situ measurements of vertical profiles of photosynthetically active radiation (PAR). Spot samples were conducted in the archipelago of south-western Finland, mainly during the ice-free growing seasons of 2010 and 2011. In addition to quantifying both the seasonal and geographical patterns of euphotic depth development, the need and usability of underwater light information are also discussed. Light availability was found to fluctuate in multiple dimensions and scales. The euphotic depth was shown to have combined spatio-temporal dynamics rather than separate changes in spatial and temporal dimensions. Such complexity in the underwater light field creates challenges in data collection, as well as in its utilisation. Although local information is needed, in highly variable conditions spot sampled information may only poorly represent its surroundings. Moreover, either temporally or spatially limited sampling may cause biases in understanding underwater light dynamics. Consequently, the application of light availability data, for example in ecological modelling, should be made with great caution.

Dynamics AX -toiminnanohjausjärjestelmän jatkuvuudenhallinta ja toipumissuunnitelma - Simulaatiotestausmalli: case CGI Suomi Oy

Nyky-yhteiskunta nojautuu vahvasti tietojärjestelmiin luoden laajemman arkkitehtuurisen kokonaisuuden, kybertoimintaympäristön. Liiketoimintaa tukevat tietojärjestelmät tukevat myös organisaatioiden prosesseja kokonaisvaltaisesti. Jotta näitä tärkeitä kyberympäristön tietojärjestelmä- sekä liiketoimintaympäristöresursseja pystytään käyttämään, tulee järjestelmien olla luotettavia ja sovellusten saatavilla vuorokauden ympäri tai aina tarvittaessa. Tilanteet, joissa järjestelmän käytettävyys vaarantuu, voivat eskaloitua yllättäen suuremmiksi, jos poikkeustilanteisiin ei ole varauduttu. Poikkeustilanteisiin varautumiseen tarvitaan jatkuvuudenhallintaa, joka on kiinteästi osa kattavampaa IT-strategiaa ja koko yhteiskunta-/yrityskulttuuria. Työ on toteutettu yhdistäen empiriaa ja teoriaa eli tavoitteena on teoreettisen tietämyksen ja käytännön kokemuksellisen oppimisen ja tietämyksen kautta luoda konstruktiivisella otteella toipumissuunnitelman testauksessa käytettävä simulaatiotestausmalli. Dynamics AX -toiminnanohjausjärjestelmän toipumissuunnitelman simulaatiotestausmallista rakentui selkeä ja kevyt työkalu asiakasyritysten toipumissuunnitelman simulaatiotestauksiin. Diplomityössä kuvatuilla keinotekoisilla järjestelmän häiriötilanteilla pystytään simuloimaan Dynamics AX:n toipumissuunnitelman testauksissa oikeita häiriötilanteita suhteellisen kattavalla tasolla.