Fractionation of Wood Extracts

The aim of this thesis was to fractionate wood extracts into pure fractions using membrane technology, to observe membrane behaviour in solvents and to study the effect of conditioning on membrane performance. Four different wood extracts were used in the performed filtrations. In the literature part, the focus was on the effect of different solvent properties on polymeric membranes, especially on their retention and flux. Solute properties, such as shape, polarity and charge, were examined. Transport models, membrane stability and ways to improve the stability, when solvents were filtered, were also discussed. The experimental part consisted of a series of filtrations, where the effect of the wood extracts and solvent concentration on solute retention was observed. Polymeric and ceramic membranes were tested under different conditions and the solute analyses were performed with GC and GC-MS. It was discovered that it is possible to fractionate wood extracts using membrane technology to some extent, but more research must be done to understand the mechanisms behind the various interactions between the solvent and the membrane. Conditioning was also considered as an important part of the membrane pre-treatment.

Research of wood fuel market in Ukraine and the Republic of Belarus

The goal of the present work was to describe the wood fuel market of Ukraine and the Republic of Belarus, to estimate wood fuel potential and to research opportunities of wood fuel trading. Nowadays the wood waste, wood residues and by-products are becoming more and more potential raw materials for energy production. Against the background of unstable prices of traditional energy sources and environmental degradation, European States are planning to get 12% of energy from alternative sources already in 2010. Wastes of wood-working and agricultural productions are such sources. At present time the most popular wood biofuels are wood pellets, briquettes, wood chips and logs. Ukraine and the Republic of Belarus have a rather big potential of wood fuel resources. But wood fuels markets of these countries are on the entry level and quite disorganized. There is almost no domestic usage of wood biofuel. All produced pellets, briquettes as well as wood chips and logs go to the export, but the volumes are not high at present time. Ukraine and the Republic of Belarus have a very suitable geographical location. The most promising directions of wood fuel trading are developed wood fuel markets of Northern countries, Austria, Germany as well as actively developing markets of Poland and Hungary. At the long distance truck and sea transportation are the most appropriate. At a short distance cheap transportation by rail is more suitable. Thereby export is a potential opportunity for development of wood fuel production and in the future for usage in the researched countries.

Research of wood fuel market in North-West of Russia

The main purposes of this study are analyzing of forest sector of North-West and research of potentials of wood fuel market in this region. Research is focused on definition of the most perspective areas for export of wood fuel: logging residues, industrial wood processing residues, pellets and briquettes. Russian wood energy industry is very young in comparison with European countries. Nowadays there are no support and serious attention from the government to this sector. Hence almost all wood fuel market is oriented to the Western Europe. Export of wood fuel is dominated over the internal consumption. Pellet production in North –West is rapidly growing. Despite internal market has been developed the lion's share of pellets goes to export. Part of industrial wood processing residues is used by producers for their own goals, part goes to the export and rest of them is not used at all. Logging residues as raw materials for fuel have great potentials; most of them are left in a forest. Special techniques for their processing are too expensive for Russian entrepreneur. Some parts of North –West, which are situated close to the border with European countries, are potential for export. Political, economical and logistical challenges are complicated facilities for foreign customer to purchase wood fuel in remote parts of North-West. However some decisions for solving this problem exist and Russian manufactures are still interested in export of their products.

Rakennukset ja rakentajat Raision Ihalassa rautakauden lopulla ja varhaisella keskiajalla

Turun yliopiston arkeologian oppiaine tutki Raision Ihalan historiallisella kylätontilla, ns. Mullin eduspellolla, asuinpaikan, josta löydettiin maamme oloissa harvinaisen hyvin säilyneitä rakennusten puuosien jäännöksiä. Löytö on ainutlaatuinen Suomen oloissa ja sillä on kansainvälistäkin merkitystä, koska hyvin säilyneet myöhemmän rautakauden ja varhaisen keskiajan maaseutuasuinpaikat, joista tavataan puujäännöksiä, ovat harvinaisia erityisesti itäisen Itämeren piirissä. Rakennukset on ennallistettu käyttäen tiukkaa paikallisen analogian (’Tight Local Analogy’) metodia, erityisesti suoraa historiallista analogista lähestymistapaa. Tätä tarkoitusta varten muodostettiin aluksi arkeologinen, historiallinen ja etnografinen lähdemalli. Tämä valittiin maantieteellisesti ja ajallisesti relevantista tutkimusaineistosta pohjoisen Itämeren piiristä. Tiedot lounaisen Suomen rakennuksista ja rakennusteknologiasta katsottiin olevan tärkein osa mallia johtuen historiallisesta ja spatiaalisesta jatkuvuudesta. Lähdemalli yhdistettiin sitten Mullin arkeologiseen aineistoon ja analyysin tuloksena saatiin rakennusten ennallistukset. Mullista on voitu ennallistaa ainakin kuusi eri rakennusta neljässä eri rakennuspaikassa. Rakennusteknologia perustui kattoa kannattaviin horisontaalisiin pitkiin seinähirsiin, jotka oli nurkissa yhdistetty joko salvoksella tai varhopatsaalla. Kaikissa rakennuksissa ulkoseinän pituus oli 5 – 7 metriä. Löydettiin lisäksi savi- ja puulattioita sekä kaksi tulisijaa, savikupoliuuni ja avoin liesi. Runsaan palaneen saven perusteella on mahdollista päätellä, että katto oli mitä todennäköisimmin kaksilappeinen vuoliaiskatto, joka oli katettu puulla ja/tai turpeella. Kaikki rakennukset olivat samaa tyyppiä ja ne käsittivät isomman huoneen ja kapean eteisen. Kaikki analysoitu puu oli mäntyä. Ulkoalueelta tavattiin lisäksi tunkioita, ojia, aitoja ja erilaisia varastokuoppia. Rakennukset on ajoitettu 900-luvun lopulta 1200-luvun lopulle (cal AD). Lopuksi tutkittiin rakennuksia yhteisöllisessä ympäristössään, niiden ajallista asemaa sekä asukkaiden erilaisia spatiaalisia kokemuksia ja yhteyksiä. Raision Ihalaa analysoidaan sosiaalisen identiteetin ja sen materiaalisten ilmenemismuotojen kautta. Nämä sosiaaliset identiteetit muodostuvat kommunikaatioverkostoista eri spatiaalisilla ja yhteisöllisillä ta¬soilla. Näitä eri tasoja ovat: 1) kotitalous arjen toimintoineen, perhe ja sukulaisuussuhteet traditioineen; 2) paikallinen identiteetti, rakennus, rakennuspaikka, asuinpaikan ympäristö ja sen käyttö, (maa)talo ja kylä; 3) Raision Ihalan kylä laajemmassa alueellisessa kontekstissaan pohjoisen Itämeren piirissä: kauppiaiden ja käsityöläisten kontaktiverkostot, uskonnollinen identiteetti ja sen muutokset.

Wood pellet markets in Russia

Bioenergy came to Russia through wood pellets. On account of prevalence of oil and gas in the Russian economy «bioenergy» has come with a great delay. Certainly, there were many woodworking enterprises and even municipal boiler-houses using wood waste and fire wood for energy reception, but this activity was not purposeful. More likely it was connected with necessity of waste recycling and with the organization of heat supply in the remote areas of the country. However, in 2001 was founded the first pellet plant in Russia. The purpose of this work was to analyze wood pellets market in Russia, investigate current situation on the home and export market, evaluates supply and demand development, opportunities for wood pellets manufactures in Russia, the main manufactures in Russian market; cost and prices for wood pellets in Russia. Also the work was intended to give better understanding of the main problems of wood pellets industry in Russia. Besides, this work had updated information about Russian customs and logistic systems.

The effect of microfibrillated cellulose addition on drying shrinkage and dimensional stability of wood-free paper

Microfibrillated cellulose (MFC) is known to enhance strength properties of paper. Improved strength usually means increased bonding which is strongly connected to dimensional instability of paper. Dimensional instability is due to changes in moisture content of paper; when paper is moistened it expands and when dried, it shrinks. Hygroexpansion is linked to end-use problems and excessive drying shrinkage consumes strength potential. Effective use of materials requires controlling of these phenomena. There isn’t yet data concerning dimensional stability of papers containing MFC which restricts wider use of MFC. Main objective of the work was to evaluate dimensional stability of wood-free paper containing different amounts of MFC. Sheets were dried with different methods to see how drying strains effected on drying shrinkage and hygroexpansion. Also tensile strength was measured to find out the effect of MFC. Results were compared to sheets containing kraft fines and in some test points cationic starch was used alongside with MFC. MFC increased the dimensional instability of freely dried sheets. As the amounts of MFC increased the effects on dimensional stability became more severe. However the fineness of MFC didn’t play any important role. Both hygroexpansion and drying shrinkage were decreased with cationic starch addition. Prevention of drying shrinkage over powered the effects of additives on hygroexpansion. Tensile strength improved up till 7 % addition amount which could be set as the upper limit of MFC addition when paper preparation and tensile strength are concerned.

Water circulations for effective bleaching of high-brightness mechanical pulps

The amount of water available is usually restricted, which leads to a situation where a complete understanding of the process, including water circulations and the influence of water components, is essential. The main aim of this thesis was to clarify the possibilities for the efficient use of residual peroxide by means of water circulation rearrangements. Rearranging water circulations and the reduction of water usage may cause new problems, such as metal induced peroxide decomposition that needs to be addressed. This thesis introduces theoretical methods of water circulations to combine two variables; effective utilization of residual peroxide and avoiding manganese in the alkaline peroxide bleaching stage. Results are mainly based on laboratory and mill site experiments concerning the utilization of residual peroxide. A simulation model (BALAS) was used to evaluate the manganese contents and residual peroxide doses. It was shown that with optimum recirculation of residual peroxide the brightness can be improved or chemical costs can be decreased. From the scientific perspective, it was also very important to discover that recycled peroxide was more effective pre-bleaching agent compared to fresh peroxide. This can be due to the organic acids i.e. per acetic acid in wash press filtrate that have been formed in alkaline bleaching stage. Even short retention time was adequate and the activation of residual peroxide using sodium hydroxide was not necessary. There are several possibilities for using residual peroxide in practice regarding bleaching. A typical modern mechanical pulping process line consist of defibering, screening, a disc filter, a bleach press, high consistency (HC) peroxide bleaching and a wash press. Furthermore there usually is not a particular medium consistency (MC) pre-bleaching stage that includes additional thickening equipment. The most advisable way to utilize residual peroxide in this kind of process is to recycle the wash press filtrate to the dilution of disc filter pulp (low MC pre-bleaching stage). An arrangement such as this would be beneficial in terms of the reduced convection of manganese to the alkaline bleaching stage. Manganese originates from wood material and will be removed to the water phase already in the early stages of the process. Recycling residual peroxide prior to the disc filter is not recommended because of low consistencies. Regarding water circulations, the novel point of view is that, it would be beneficial to divide water circulations into two sections and the critical location for the division is the disc filter. Both of these two sections have their own priority. Section one before the disc filter: manganese removal. Section two after the disc filter: brightening of pulp. This division can be carried out if the disc filter pulp is diluted only by wash press filtrate before the MC storage tower. The situation is even better if there is an additional press after the disc filter, which will improve the consistency of the pulp. This has a significant effect on the peroxide concentration in the MC pre-bleaching stage. In terms of manganese content, it is essential to avoid the use of disc filter filtrate in the bleach press and wash press showers. An additional cut-off press would also be beneficial for manganese removal. As a combination of higher initial brightness and lower manganese content, the typical brightness increase varies between approximately 0.5 and 1% ISO units after the alkaline peroxide bleaching stage. This improvement does not seem to be remarkable, but as it is generally known, the final brightness unit is the most expensive and difficult to achieve. The estimation of cost savings is not unambiguous. For example in GW/TMP mill case 0.6% ISO units higher final brightness gave 10% savings in the costs of bleaching chemicals. With an hypothetical 200 000 ton annual production, this means that the mill could save in the costs of bleaching chemicals more than 400 000 euros per year. In general, it can be said that there were no differences between the behavior of different types of processes (GW, PGW, TMP and BCTMP). The enhancement of recycling gave a similar response in all cases. However, we have to remember that the utilization of residual peroxide in older mills depends a great deal on the process equipment, the amount of water available and existing pipeline connections. In summary, it can be said that processes are individual and the same solutions cannot be applied to all cases.

Factors affecting the usability of aspen (Populus tremula) wood dried at different temperature levels

In this dissertation the main aim was to study the usability of aspen wood in the mechanical wood processes, especially the factors that affect the usability of aspen wood, which is dried at different temperature levels. The problematic of varying temperatures from level to another seem to have significant effects on distortions. According to the studies conducted, many practical solutions for drying of aspen timber can be made. European aspen sawn timber should be dried in relatively narrow widths, short lengths, edged and sawn pith free. The results achieved give an interesting view for the distortions of aspen wood between HT drying and heat treatment. The most significant result is that cupping seems to decrease when increasing temperature level from HT drying to heat treatment phase. The difference is significant. Other very obvious result is that bow and crook are increasing between these two temperature levels, bow significantly. Also the modelling gives a good background for this result since cupping is reduced by higher temperatures. It can also be assumed that these distortions can be affected for example by sorting out the timber used to different moisture levels before drying. This could be a very simple solution for practical purposes. From practical point of view, it was also noted during the drying tests performed that the discoloration seem to be no problem for aspen boards dried in temperatures under 150 °C. Altogether, this dissertation covers many interesting points of view of factors affecting distortions of wood in different temperature stages. Aspen as species in use of mechanical wood industries seems to be a species suitable for component production. According to the results, the best yield from aspen timber can be achieved in industry that can utilize relatively short components of sawn wood. Results achieved give a significant indication about the factors affecting distortions of wood at different temperature stages of drying, especially considering European aspen.

Effects of Surface Properties and Wood Modification into Direct Printing on Wood

Building industry is a high volume branch which could provide prominent markets for wood based interior decoration solutions. Competition in interior decoration markets requires versatility in appearance. Versatility in wood appearance and added value could be achieved by printing grain patterns of different species or images directly onto wood. The problem when planning wood printing’s implementing into durable applications is basically how to transfer a high quality image or print sustainably onto wood, which is porous, heterogeneous, dimensionally unstable, non-white and rough. Wood preservation or treating, and modification can provide durability against degradation but also effect to the surface properties of wood which will effect on printability. Optimal adhesion is essential into print quality, as too high ink absorbance can cause spreading and too low ink absorbance cause pale prints. Different printing techniques have different requirements on materials and production. The direct printing on wood means, that intermedias are not used. Printing techniques with flexible printing plates or in fact non-impact techniques provide the best basis for wood printing. Inkjet printing of wood with different mechanical or chemical surface treatments, and wood plastic composite material gave good results that encourage further studies of the subject. Sanding the wood surface anti-parallel to the grain gave the best overall printing quality. Spreading parallel to the grain could not be avoided totally, except in cases where wood was treated hydrophobic so adhesion of the ink was not sufficient. Grain pattern of the underlying wood stays clearly visible in the printed images. Further studies should be made to fine tune the methods that already gave good results. Also effects of moisture content of wood, different inks, and long-term exposure to UV-radiation should be tested.