Influence of Pulsed-Electric Field Irradiation in Crystallization

The growing pharmaceutical interest, among others, in the polymorphic composition of the emerging solid end-products from production processes has been traced to the need for attainment of high product purity. This is more so as the presence of different polymorphs may constitute physical impurity of the product. Hence, the need for optimization of the yield of desired product component(s) through controlled crystallization kinetics for instance. This study was carried out to investigate the impact of pulsed electric field (PEF) irradiation on the crystal morphology of glycine obtained by cooling crystallization (without seeding) from commercial glycine sample in distilled deionized water solution. In doing so, three different pulse frequencies (294, 950 and 145 Hz) and a case without PEF were studied at three cooling rates (5, 10 and 20 ºC/h). The crystal products obtained were analyzed for polymorphic composition by powder x-ray diffraction (PXRD) and Fourier transform infrared (FTIR) spectroscopy while the particles characterization was done on Morphologi G3. The results obtained from this study showed that pulsed electric field irradiation had significant impact on metastability of the aqueous solution as well as on the polymorphic composition of the end product. With increasing PEF frequency applied, nucleation started earlier and the γ-glycine polymorph content of the product crystals increased. These were found to have been aided by cooling rate, as the most significant effect was observed at 5 ºC/h. It was also discovered that PEF application had no measurable impact on the pH of the aqueous solution as well as the size distribution of the particles. Cooling on the contrary was believed to be responsible for the broadening of the particle size distribution with a downward shift of the lower limit of the raw material from about 100 μm to between 10 and 50 μm.

Intensification of hemicellulose hot-water extraction from spruce wood by parameter tuning

The growing population on earth along with diminishing fossil deposits and the climate change debate calls out for a better utilization of renewable, bio-based materials. In a biorefinery perspective, the renewable biomass is converted into many different products such as fuels, chemicals, and materials, quite similar to the petroleum refinery industry. Since forests cover about one third of the land surface on earth, ligno-cellulosic biomass is the most abundant renewable resource available. The natural first step in a biorefinery is separation and isolation of the different compounds the biomass is comprised of. The major components in wood are cellulose, hemicellulose, and lignin, all of which can be made into various end-products. Today, focus normally lies on utilizing only one component, e.g., the cellulose in the Kraft pulping process. It would be highly desirable to utilize all the different compounds, both from an economical and environmental point of view. The separation process should therefore be optimized. Hemicelluloses can partly be extracted with hot-water prior to pulping. Depending in the severity of the extraction, the hemicelluloses are degraded to various degrees. In order to be able to choose from a variety of different end-products, the hemicelluloses should be as intact as possible after the extraction. The main focus of this work has been on preserving the hemicellulose molar mass throughout the extraction at a high yield by actively controlling the extraction pH at the high temperatures used. Since it has not been possible to measure pH during an extraction due to the high temperatures, the extraction pH has remained a “black box”. Therefore, a high-temperature in-line pH measuring system was developed, validated, and tested for hot-water wood extractions. One crucial step in the measurements is calibration, therefore extensive efforts was put on developing a reliable calibration procedure. Initial extractions with wood showed that the actual extraction pH was ~0.35 pH units higher than previously believed. The measuring system was also equipped with a controller connected to a pump. With this addition it was possible to control the extraction to any desired pH set point. When the pH dropped below the set point, the controller started pumping in alkali and by that the desired set point was maintained very accurately. Analyses of the extracted hemicelluloses showed that less hemicelluloses were extracted at higher pH but with a higher molar-mass. Monomer formation could, at a certain pH level, be completely inhibited. Increasing the temperature, but maintaining a specific pH set point, would speed up the extraction without degrading the molar-mass of the hemicelluloses and thereby intensifying the extraction. The diffusion of the dissolved hemicelluloses from the wood particle is a major part of the extraction process. Therefore, a particle size study ranging from 0.5 mm wood particles to industrial size wood chips was conducted to investigate the internal mass transfer of the hemicelluloses. Unsurprisingly, it showed that hemicelluloses were extracted faster from smaller wood particles than larger although it did not seem to have a substantial effect on the average molar mass of the extracted hemicelluloses. However, smaller particle sizes require more energy to manufacture and thus increases the economic cost. Since bark comprises 10 – 15 % of a tree, it is important to also consider it in a biorefinery concept. Spruce inner and outer bark was hot-water extracted separately to investigate the possibility to isolate the bark hemicelluloses. It was showed that the bark hemicelluloses comprised mostly of pectic material and differed considerably from the wood hemicelluloses. The bark hemicelluloses, or pectins, could be extracted at lower temperatures than the wood hemicelluloses. A chemical characterization, done separately on inner and outer bark, showed that inner bark contained over 10 % stilbene glucosides that could be extracted already at 100 °C with aqueous acetone.

Suodattimessa tapahtuvan kiintoaineen laskeutumisen vaikutus suodinkakun ominaisuuksiin

Laskeutus ja suodatus ovat paljon tutkittuja ja laajassa käytössä olevia mekaanisia erotusmenetelmiä. Laskeutumisen vaikutusta suodatuksen yhteydessä ei kuitenkaan ole tutkittu juurikaan. Tämän työn tavoitteena on selvittää suodattimessa ennen vakiopaine suodatusta tapahtuvan kiintoaineen laskeutumisen vaikutusta suodatuksen tuloksiin. Työn kirjallisuusosuudessa käsitellään työhön liittyvää teoriaa partikkelikokojakaumista, laskeutumisesta, suodatuksesta ja flokkulanttien käytöstä sekä tehdään yhteenvetoa aiemmasta laskeutumista ja suodatusta yhdistävästä tutkimuksesta. Koska käsitellyt aiheet ovat laajoja ja niitä on useita, joudutaan teorian esittämisessä tekemään rajauksia. Työn kokeellisessa osassa tutkitaan suodattimessa tapahtuvan laskeutuksen vaikutusta suodatukseen. Kokeet suoritetaan 20 m-% kalsiumkarbonaattilietteellä. Kokeissa tutkitaan laskeutumisen vaikutusta antamalla lietteen laskeutua suodattimessa tietyn ajan ennen suodatuksen aloitusta. Lisäksi tutkitaan flokkulanttien lisäämisen vaikutusta mahdollisiin ilmiöihin. Koetuloksista nähdään pidemmän laskeutusajan ennen suodatusta alentavan kakun keskimääräistä ominaisvastusta ja vaikutus kasvaa merkittävästi kun lietteeseen on lisätty flokkulanttia. Suodatusta edeltävä laskeutus siis helpottaa varsinaista suodatusta.

Biomassan käsittely voimalaitoksissa

Tässä diplomityössä tutkitaan biomassan esikäsittelyä suurissa voimalaitoksissa. Työssä keskitytään puusta saataviin polttoaineisiin. Biomassan esikäsittely on tärkeä osa voimalaitoksen toimintaa. Sillä pyritään saamaan puulle halutut ominaisuudet loppukäyttöä, kuten polttoa tai kaasutusta varten. Puubiomassan tärkeimpiä ominaisuuksia ovat kosteus, palakoko ja tasalaatuisuus. Työ on jaettu neljään osaan. Ensimmäisessä osassa tutkitaan kiinteän biomassan ominaisuuksia ja ongelmia. Toisessa osassa esitellään erilaisia voimalaitoksissa käytettäviä puubiomassoja ja niiden erityisominaisuuksia ja -vaatimuksia. Kolmannessa osassa esitellään biomassan käsittelyä voimalaitoksella. Käsittely jaotellaan vastaanottoon, esikäsittelyyn, varastointiin ja käsittelylaitteistoihin. Kolmannessa osassa tutkitaan myös käsittelyn erityisvaatimuksia ja esitellään esimerkkejä biomassan kokonaiskäsittelystä laitoksella. Työn neljäs osa paneutuu biomassan käsittelyn turvallisuus- ja ympäristöasioihin. Puubiomassan esikäsittely on suunniteltava käytettävien puulaatujen ja -määrien mukaan. Biomassan kosteuden ollessa korkea, on tutkittava onko kuivurien käyttö kannattavaa ja perusteltua. Jos voimalaitokselle tuleva puu on epätasalaatuista tai sisältää epäpuhtauksia, on käytettävä erilaisia puhdistus- ja murskainlaitteistoja. Biomassan käsittelyssä syntyy melua ja päästöjä. Ympäristö- ja terveyshaittojen ehkäisemiseksi käsittelylaitteistoihin on suunniteltava tarpeelliset suojat ja varojärjestelmät.

Influence of multi-phase phenomena on semibatch crystallization processes of aqueous solutions

Crystal properties, product quality and particle size are determined by the operating conditions in the crystallization process. Thus, in order to obtain desired end-products, the crystallization process should be effectively controlled based on reliable kinetic information, which can be provided by powerful analytical tools such as Raman spectrometry and thermal analysis. The present research work studied various crystallization processes such as reactive crystallization, precipitation with anti-solvent and evaporation crystallization. The goal of the work was to understand more comprehensively the fundamentals, phenomena and utilizations of crystallization, and establish proper methods to control particle size distribution, especially for three phase gas-liquid-solid crystallization systems. As a part of the solid-liquid equilibrium studies in this work, prediction of KCl solubility in a MgCl2-KCl-H2O system was studied theoretically. Additionally, a solubility prediction model by Pitzer thermodynamic model was investigated based on solubility measurements of potassium dihydrogen phosphate with the presence of non-electronic organic substances in aqueous solutions. The prediction model helps to extend literature data and offers an easy and economical way to choose solvent for anti-solvent precipitation. Using experimental and modern analytical methods, precipitation kinetics and mass transfer in reactive crystallization of magnesium carbonate hydrates with magnesium hydroxide slurry and CO2 gas were systematically investigated. The obtained results gave deeper insight into gas-liquid-solid interactions and the mechanisms of this heterogeneous crystallization process. The research approach developed can provide theoretical guidance and act as a useful reference to promote development of gas-liquid reactive crystallization. Gas-liquid mass transfer of absorption in the presence of solid particles in a stirred tank was investigated in order to gain understanding of how different-sized particles interact with gas bubbles. Based on obtained volumetric mass transfer coefficient values, it was found that the influence of the presence of small particles on gas-liquid mass transfer cannot be ignored since there are interactions between bubbles and particles. Raman spectrometry was successfully applied for liquid and solids analysis in semi-batch anti-solvent precipitation and evaporation crystallization. Real-time information such as supersaturation, formation of precipitates and identification of crystal polymorphs could be obtained by Raman spectrometry. The solubility prediction models, monitoring methods for precipitation and empirical model for absorption developed in this study together with the methodologies used gives valuable information for aspects of industrial crystallization. Furthermore, Raman analysis was seen to be a potential controlling method for various crystallization processes.

Quality assurance of refuse derived fuel with machine vision

This thesis studies the use of machine vision in RDF quality assurance and manufacturing. Currently machine vision is used in recycling and material detection and some commer- cial products are available in the market. In this thesis an on-line machine vision system is proposed for characterizing particle size. The proposed machine vision system is based on the mapping between image segmenta- tion and the ground truth of the particle size. The results shows that the implementation of such machine vision system is feasible.

Development and characterization of thin printed films for gas sensing applications

The monitoring and control of hydrogen sulfide (H2S) level is of great interest for a wide range of application areas including food quality control, defense and antiterrorist applications and air quality monitoring e.g. in mines. H2S is a very poisonous and flammable gas. Exposure to low concentrations of H2S can result in eye irritation, a sore throat and cough, shortness of breath, and fluid retention in the lungs. These symptoms usually disappear in a few weeks. Long-term, low-level exposure may result in fatigue, loss of appetite, headache, irritability, poor memory, and dizziness. Higher concentrations of 700 - 800 ppm tend to be fatal. H2S has a characteristic smell of rotten egg. However, because of temporary paralysis of olfactory nerves, the smelling capability at concentrations higher than 100 ppm is severely compromised. In addition, volatile H2S is one of the main products during the spoilage of poultry meat in anaerobic conditions. Currently, no commercial H2S sensor is available which can operate under anaerobic conditions and can be easily integrated in the food packaging. This thesis presents a step-wise progress in the development of printed H2S gas sensors. Efforts were made in the formulation, characterization and optimization of functional printable inks and coating pastes based on composites of a polymer and a metal salt as well as a composite of a metal salt and an organic acid. Different processing techniques including inkjet printing, flexographic printing, screen printing and spray coating were utilized in the fabrication of H2S sensors. The dispersions were characterized by measuring turbidity, surface tension, viscosity and particle size. The sensing films were characterized using X-ray photoelectron spectroscopy, X-ray diffraction, atomic force microscopy and an electrical multimeter. Thin and thick printed or coated films were developed for gas sensing applications with the aim of monitoring the H2S concentrations in real life applications. Initially, a H2S gas sensor based on a composite of polyaniline and metal salt was developed. Both aqueous and solvent-based dispersions were developed and characterized. These dispersions were then utilized in the fabrication of roll-to-roll printed H2S gas sensors. However, the humidity background, long term instability and comparatively lower detection limit made these sensors less favourable for real practical applications. To overcome these problems, copper acetate based sensors were developed for H2S gas sensing. Stable inks with excellent printability were developed by tuning the surface tension, viscosity and particle size. This enabled the formation of inkjet-printed high quality copper acetate films with excellent sensitivity towards H2S. Furthermore, these sensors showed negligible humidity effects and improved selectivity, response time, lower limit of detection and coefficient of variation. The lower limit of detection of copper acetate based sensors was further improved to sub-ppm level by incorporation of catalytic gold nano-particles and subsequent plasma treatment of the sensing film. These sensors were further integrated in an inexpensive wirelessly readable RLC-circuit (where R is resistor, L is inductor and C is capacitor). The performance of these sensors towards biogenic H2S produced during the spoilage of poultry meat in the modified atmosphere package was also demonstrated in this thesis. This serves as a proof of concept that these sensors can be utilized in real life applications.

Carponate precipitation with carbon dioxide gas

The aim of this thesis research work focused on the carbonate precipitation of magnesium using magnesium hydroxide Mg(OH)2 and carbon dioxide (CO2) gas at ambient temperature and pressure. The rate of dissolution of Mg(OH)2 and precipitation kinetics were investigated under different operating conditions. The conductivity and pH of the solution were inline monitored by a Consort meter and the solid samples gotten from the precipitation reaction were analysed by a laser diffraction analyzer Malvern Mastersizer to obtain particle size distributions (PSD) of crystal samples. Also the Mg2+ concentration profiles were determined from the liquid phase of the precipitate by ion chromatography (IC) analysis. Crystal morphology of the obtained precipitates were also investigated and discussed in this work. For the carbonation reaction of magnesium hydroxide in the present work, it was found that magnesium carbonate trihydrate (nesquehonite) was the main product and its formation occurred at a pH of around 7-8. The stirrer speed has a significant effect on the dissolution rate of Mg(OH)2. The highest obtained Mg2+ concentration level was 0.424 mol L-l for the 470 rpm and 0.387 mol L-1 for the 560 rpm which corresponded to the processing time of 45 mins and 40 mins respectively. The particle size distribution shows that the average particle size keeps increasing during the reaction as the CO2 is been fed to the system. The carbonation process is kinetically favored and simple as nesquehonite formation occurs in a very short time. It is a thermodynamically and chemically stable solid product, which allows for a long-term storage of CO2. Since the carbonation reaction is a complex system which includes dissolution of magnesium hydroxide particles, absorption of CO2, chemical reaction and crystallization, the dissolution of magnesium hydroxide was studied in hydrochloric acid (HCl) solvent with and without nitrogen (N2) inert gas. It was found on the dissolution part that the impeller speed had effect on the dissolution rate. The higher the impeller speed the higher the pH of the solution, although for the highest speed of 650rpm it was not the case. Therefore, it was concluded that the optimum speed of the stirrer was 560rpm. The influence of inert gas N2 on the dissolution rate of Mg(OH)2 particles could be seen based on measured pH, electric conductivity and Mg2+ concentration curves.

Characterization of amine-based CO2 adsorbent for Direct Air Capture

Direct air capture technologies extract CO2 from air at a concentration of as low as 400ppm. The captured CO2 can be used for the production of synthetic methane or liquid fuels. In the literature survey of this thesis, results related to direct air capture by using solid sorbents are presented and critically discussed. In the experimental part, a proprietary amine functionalized resin is characterized for direct air capture. Structural comparison is also made to a commercial resin of similar type. Based on the literature survey, the most important parameters in direct air capture process are low adsorption and desorption temperatures, good cyclic stability in dry and humid conditions, high CO2 outlet purity and a high working capacity. Primary amine functionalized solid sorbents are found to often have good qualities for direct air capture, but overall process performance is rarely studied exhaustively. Based on FTIR spectra, both resin adsorbents are found to be consisted of polystyrene functionalized with primary amine, and capture CO2 by forming carbamate. The commercial resin is more porous, has a slightly higher particle size and contains fewer impurities. Important physical parameters are gained of the proprietary resin, such as internal porosity and median particle size. The resin’s amine group is found to endure thermal treatment reasonably well. CO2 adsorption capacity gained by thermal gravimetry from 400ppm CO2 is highest at 25oC, and is found to be reasonable compared to values presented in literature. Thus, the resin is stated to exhibit promising qualities for direct air capture.

Characterization of the filter media used in the dual media filter

The removal of organics from copper electrolyte solutions after solvent extraction by dual media filtration is one of the most efficient ways to ensure the clean electrolyte flow into the electrowinning. The clean electrolyte will ensure the good quality cathode plate production. Dual media filtration uses two layers of filter media for filtration as anthracite and garnet respectively. The anthracite layer will help the coalescing of the entrained organic droplets which will then float to the top of the filter, and back to the solvent extraction process. The garnet layer will catch any solids left in the electrolyte traveling through the filter media. This thesis will concentrate on characterization of five different anthracites in order to find some differences using specific surface area analysis, particle size analysis, and morphology analysis. These results are compared to the pressure loss values obtained from lab column tests and bed expansion behavior. The goal of the thesis was to find out if there were any differences in the anthracite which would make the one perform better than the other. There were no big differences found on any aspect of the particle characterization, but some found differences should be further studied in order to confirm the meaning of the porosity, surface area, intensity mean and intensity SD (Standard Deviation) on anthracites and their use in dual media filtration. The thesis work analyzed anthracite samples the way that is not found on any public literature sources, and further studies on the issue would bring more knowledge to the electrolyte process.

Jauhatusparametrien vaikutus jauhatustuotteen partikkelikokoon ja suodattuvuuteen

Tämän diplomityön tarkoituksena on tutkia ensin jauhatusparametrien vaikutus rikastushiekan hienousasteeseen eli miten partikkelikokojakaumaa kuvaavat partikkelikoot muuttuvat. Tämän jälkeen tutkitaan miten rikastushiekan hienousasteen muuttuminen vaikuttaa jauhettujen rikastushiekkalietenäytteiden suodattuvuuteen. Partikkelikokojakauman variaatioista yritetään löytää yhteys suodinkakun ominaisvastuksen ja huokoisuuden välillä. Jauhatus suoritettiin laboratoriomittakaavan helmimyllyllä märkäjauhatuksena. Jauhatusta varten tehtiin kolmitasoinen faktorikoesuunnitelma, jossa muuttujina ovat lasihelmien halkaisija, jauhatusaika ja sekoitinelimen pyörimisnopeus. Suodatus toteutettiin vakiopainesuodatuksena kolmella eri suodatuspaineella Nutsche-suodattimella. Työn tuloksista saatiin selville, että partikkelikokojakauman leveys korreloi suodinkakun ominaisvastuksen kanssa. Kun partikkelikokojakauma leveys muuttui kapeammaksi, saatiin kakun ominaisvastus pienemmäksi ja suodatukseen kulunut aika lyheni. Kapein partikkelikokojakauman leveys saatiin suurimmalla helmen halkaisijalla, pisimmällä jauhatusajalla sekä suurimmalla sekoitusnopeudella.

Sähkösuodattimen mahdollisuudet sisäilman parantajana

Diplomityön tavoitteena oli selvittää, kuinka sähkösuodattimella voidaan vaikuttaa sisäilman laatuun ja kuinka kilpailukykyinen vaihtoehto pienkiinteistöissä sähkösuodatin on perinteisiin kuitusuodattimiin verrattuna. Teoriaosassa tarkasteltiin, kuinka ilman hengitettävät hiukkaset muodostuvat ja miten ne vaikuttavat sisäilman laatuun sekä ihmisten terveyteen. Tarkasteltiin hiukkasten koon, lukumäärän, massan ja pinta-alan yhteyksiä niiden terveysvaikutuksiin. Ultrapienet hiukkaset ovat terveydelle haitallisimpia, koska hiukkasten lukumäärä ja pinta-ala lisäävät terveyshaittoja enemmän kuin hiukkasten massa. Tutkittiin pienkiinteistöjen ilmanvaihtoratkaisuja ja erilaisia tuloilmanpuhdistus-menetelmiä. Soveltavassa osassa tarkasteltiin sähkösuodattimen toimintaa ja sen mahdollisuuksia sisäilman parantajana verrattuna perinteisiin kuitusuodattimiin. Tehtiin sähkösuodattimen ja kuitusuodattimen välinen elinkaarikustannusvertailu keskisuurelle omakotitalolle. Kirjallisuuden ja tutkimushavaintojen perusteella sähkösuodattimen suurin etu muihin suodattimiin verrattuna on sen kyky poistaa kaiken kokoisia, myös ultrapieniä, hengitettäviä hiukkasia ja siten tehokkaasti vähentää hengitettävien hiukkasten lukumäärää ja pinta-alaa. Tällä voi olla vaikutusta yleisten terveyshaittojen ja ympäristöherkkyyden ennaltaehkäisemisessä. Ympäristöherkkyyteen sairastuneiden oireiluun sähkösuodatin voi tuottaa helpotusta kotioloissa ja siirrettävän ilmanpuhdistimen avulla myös työpaikoilla. Elinkaarikustannusvertailun perusteella selvisi, että sähkösuodatin on kalliimmasta hinnastaan huolimatta kokonaiskustannuksiltaan selvästi edullisempi vaihtoehto kuin kuitusuodattimet. Sähkösuodattimen haasteena on uuden teknologian lanseeraaminen pientalorakentamiseen. Pienrakennusten tuloilman puhdistusmenetelmien kehittämisellä olisi mahdollista parantaa suomalaisten elämänlaatua ja saavuttaa merkittäviä säästöjä terveydenhoitokuluissa.