CO2 sparging for improving the filtration properties of iron ore slurries

Iron ore treatment processes are usually continuous and high tonnage and filtration equipment has to meet these requirements. In magnetite (Fe3O4) treatment process continuous rotary disc filters are often used for filtration. Carbon dioxide (CO2) treatment is a fairly novel and un-known filtration enhancing process. The interest to use CO2 is quite high because CO2 is a greenhouse gas that is abundant, readily available and capture and use of CO2 would be environmentally beneficial. The focus of this thesis was to investigate if CO2 could be used to enhance the filtration of magnetite with ceramic disc filter. Previous studies have suggested that CO2 could be used to enhance the filtration properties of different iron ores thus increasing the filtration capacity. In the literature part, the basic theory of filtration and the particle properties affecting filtration were discussed. The basic steps of a typical ore treatment process were presented. The reasons why CO2 might enhance the filtration properties of different ores were investigated. A literature survey of earlier studies of CO2 addition as a filter aid was presented and the basic chemical properties and reactions of CO2 were also discussed. The experimental part was done at the LUT Laboratory of Separation Technology using different magnetite samples from the industry. The filtration experiments indicated that CO2 had a positive influence on the filtration properties of magnetite slurry. Zeta potential of untreated and CO2 treated magnetite was measured and CO2 treated magnetite had lower zeta potential values than the untreated magnetite. The filtration capacity was increased while the cake moisture levels were only slightly increased.

Extraction of polymeric galactoglucomannans from spruce wood by pressurized hot water

The major type of non-cellulosic polysaccharides (hemicelluloses) in softwoods, the partly acetylated galactoglucomannans (GGMs), which comprise about 15% of spruce wood, have attracted growing interest because of their potential to become high-value products with applications in many areas. The main objective of this work was to explore the possibilities to extract galactoglucomannans in native, polymeric form in high yield from spruce wood with pressurised hot-water, and to obtain a deeper understanding of the process chemistry involved. Spruce (Picea abies) chips and ground wood particles were extracted using an accelerated solvent extractor (ASE) in the temperature range 160 – 180°C. Detailed chemical analyses were done on both the water extracts and the wood residues. As much as 80 – 90% of the GGMs in spruce wood, i.e. about 13% based on the original wood, could be extracted from ground spruce wood with pure water at 170 – 180°C with an extraction time of 60 min. GGMs comprised about 75% of the extracted carbohydrates and about 60% of the total dissolved solids. Other substances in the water extracts were xylans, arabinogalactans, pectins, lignin and acetic acid. The yields from chips were only about 60% of that from ground wood. Both the GGMs and other non-cellulosic polysaccharides were extensively hydrolysed at severe extraction conditions when pH dropped to the level of 3.5. Addition of sodium bicarbonate increased the yields of polymeric GGMs at low additions, 2.5 – 5 mM, where the end pH remained around 3.9. However, at higher addition levels the yields decreased, mainly because the acetyl groups in GGMs were split off, leading to a low solubility of GGMs. Extraction with buffered water in the pH range 3.8 – 4.4 gave similar yields as with plain water, but gave a higher yield of polymeric GGMs. Moreover, at these pH levels the hydrolysis of acetyl groups in GGMs was significantly inhibited. It was concluded that hot-water extraction of polymeric GGMs in good yields (up to 8% of wood) demands appropriate control of pH, in a narrow range about 4. These results were supported by a study of hydrolysis of GGM at constant pH in the range of 3.8 – 4.2 where a kinetic model for degradation of GGM was developed. The influence of wood particle size on hot-water extraction was studied with particles in the range of 0.1 – 2 mm. The smallest particles (< 0.1 mm) gave 20 – 40% higher total yield than the coarsest particles (1.25 – 2 mm). The difference was greatest at short extraction times. The results indicated that extraction of GGMs and other polysaccharides is limited mainly by the mass transfer in the fibre wall, and for coarse wood particles also in the wood matrix. Spruce sapwood, heartwood and thermomechnical pulp were also compared, but only small differences in yields and composition of extracts were found. Two methods for isolation and purification of polymeric GGMs, i.e. membrane filtration and precipitation in ethanol-water, were compared. Filtration through a series of membranes with different pore sizes separated GGMs of different molar masses, from polymers to oligomers. Polysaccharides with molar mass higher than 4 kDa were precipitated in ethanol-water. GGMs comprised about 80% of the precipitated polysaccharides. Other polysaccharides were mainly arabinoglucuronoxylans and pectins. The ethanol-precipitated GGMs were by 13C NMR spectroscopy verified to be very similar to GGMs extracted from spruce wood in low yield at a much lower temperature, 90°C. The obtained large body of experimental data could be utilised for further kinetic and economic calculations to optimise technical hot-water extractionof softwoods.

Solids removal in pyrolysis

Pyrolysis is a process for turning biomass into liquid fuel. The process consists of heating the biomass in inert conditions and quenching the resulting vapors into oil. The oil has many potential uses, such as heating fuel in peak heating plants. In order to broaden the application base and improve the quality of the oil, solids removal has to be addressed. The solids may also increase the probability of plugging in downstream equipment. The purpose of this research was to gain an understanding of the formation of solids in the pyrolysis process and to assess options for reducing the solid content of the oil. From literature it is known that the solids can be removed either by hot vapor filtration, liquid treatment or multiple cyclones. Hot vapor filtration decreases yield, but improves the stability of the oil while simultaneously removing solids and ash. Liquid treatment techniques are good for removing large particles but involve losses of pyrolysis liquid. Cyclones are a traditional robust technique used regularly in pyrolysis. In the experimental part of this thesis, a 2 MWfuel pyrolysis setup with 2 cyclones in series was operated and monitored. Solid and liquid samples were collected from various parts of the process for further examination. Sampling and sample treatment techniques were developed. The chemical properties of the pyrolysis char were also analyzed and assessed as a function of reactor temperature and fluidizing velocity. By measuring the particle size distributions it was noticed that there were much smaller particles collected from the second cyclone than fed into pyrolysis. The solids in the pyrolysis oil were even smaller. This was most likely caused by attrition and shrinkage. Due to better separation efficiency of the cyclones in large particles, excess attrition should be avoided.

Searchig the links between "knowledge governance mechanisms", "the individual conditions of knowledge sharing", and "individual's knowledge sharing behaviour".

The objective of this study was to understand how organizational knowledge governance mechanisms affect individual motivation, opportunity, and the ability to share knowledge (MOA framework), and further, how individual knowledge-sharing conditions affect actual knowledge sharing behaviour. The study followed the knowledge governance approach and a micro-foundations perspective to develop a theoretical model and hypotheses, which could explain the casual relationships between knowledge governance mechanisms, individual knowledge sharing conditions, and individual knowledge sharing behaviour. The quantitative research strategy and multivariate data analysis techniques (SEM) were used in the hypotheses testing with a survey dataset of 256 employees from eleven military schools of Finnish Defence Forces (FDF). The results showed that “performance-based feedback and rewards” affects employee’s “intrinsic motivation towards knowledge sharing”, that “lateral coordination” affects employee’s “knowledge self-efficacy”, and that ”training and development” is positively related to “time availability” for knowledge sharing but affects negatively employee’s knowledge self-efficacy. Individual motivation and knowledge self-efficacy towards knowledge sharing affected knowledge sharing behaviour when work-related knowledge was shared 1) between employees in a department and 2) between employees in different departments, however these factors did not play a crucial role in subordinate–superior knowledge sharing. The findings suggest that individual motivation, opportunity, and the ability towards knowledge sharing affects individual knowledge sharing behaviour differently in different knowledge sharing situations. Furthermore, knowledge governance mechanisms can be used to manage individual-level knowledge sharing conditions and individual knowledge sharing behaviour but their affect also vary in different knowledge sharing situations.

Mikrohuokoisen pinnoitteen kehittäminen suodatinkankaan päälle

Mikrohuokoisia membraaneja käytetään monissa suodatussovelluksissa kuten vedenpuhdistuksessa. Tämän työn tavoite oli pinnoittaa suodatinkankaita mikrohuokoisella membraanilla. Membraanimateriaalin ja suodatuskankaan yhdistelmällä tavoiteltiin komposiittimateriaalia, jolla on membraanin selektiivinen erotuskyky ja kankaan mekaaniset ominaisuudet. Tämän työn kirjallisuusosa käsittelee membraanin valmistusta faasi-inversiomenetelmällä, pinnoitteeksi soveltuvia membraanimateriaaleja sekä pinnoitteen lujittamista. Kokeellisessa osassa suodatuskankaalle kehitettiin sopivaa pinnoitusmenetelmää. Pinnoitemateriaaleina käytettiin akryylidispersioainetta, polyamidia ja polysulfonia. Tuloksista huomattiin, ettei akryylidispersioaine soveltunut pinnoitemateriaaliksi. Kangasta onnistuttiin pinnoittamaan polyamidilla ja pinnoitusolosuhteita kontrolloimalla saatiin aikaiseksi pinnoite, joka pysyi kankaassa kiinni ja jonka rakenne koostui noin 12 μm huokosista. Polymeeriliuoksen pitoisuuden huomattiin vaikuttavan pinnoitteen rakenteeseen, mutta siihen jäi edelleen suuria avoimia huokosia. Suuret yksittäiset huokoset laskivat kuplapistepainetta ja tekivät huokoskokojakaumasta leveämmän. Polyamidipitoisuudella 14 ja 16 m–% pinnoite oli tunkeutunut kankaan sisään ja sen rakenne oli huokoinen, mutta pintakerrokseen muodostunut tiivis ihokerros tukki materiaalia. Tulosten perusteella kankaiden pinnoittaminen membraanikerroksella on mahdollista mutta pinnoitusprosessia täytyy edelleen kehittää, jotta päästään pienempään huokoskokoon ja kapeampaan huokoskokojakaumaan pinnoitteessa.

Recovery of biomass-derived valuable compounds using chromatographic and membrane separations

Utilization of biomass-based raw materials for the production of chemicals and materials is gaining an increasing interest. Due to the complex nature of biomass, a major challenge in its refining is the development of efficient fractionation and purification processes. Preparative chromatography and membrane filtration are selective, energy-efficient separation techniques which offer a great potential for biorefinery applications. Both of these techniques have been widely studied. On the other hand, only few process concepts that combine the two methods have been presented in the literature. The aim of this thesis was to find the possible synergetic effects provided by combining chromatographic and membrane separations, with a particular interest in biorefinery separation processes. Such knowledge could be used in the development of new, more efficient separation processes for isolating valuable compounds from complex feed solutions that are typical for the biorefinery environment. Separation techniques can be combined in various ways, from simple sequential coupling arrangements to fully-integrated hybrid processes. In this work, different types of combined separation processes as well as conventional chromatographic separation processes were studied for separating small molecules such as sugars and acids from biomass hydrolysates and spent pulping liquors. The combination of chromatographic and membrane separation was found capable of recovering high-purity products from complex solutions. For example, hydroxy acids of black liquor were successfully recovered using a novel multistep process based on ultrafiltration and size-exclusion chromatography. Unlike any other separation process earlier suggested for this challenging separation task, the new process concept does not require acidification pretreatment, and thus it could be more readily integrated into a pulp-mill biorefinery. In addition to the combined separation processes, steady-state recycling chromatography, which has earlier been studied for small-scale separations of high-value compounds only, was found a promising process alternative for biorefinery applications. In comparison to conventional batch chromatography, recycling chromatography provided higher product purity, increased the production rate and reduced the chemical consumption in the separation of monosaccharides from biomass hydrolysates. In addition, a significant further improvement in the process performance was obtained when a membrane filtration unit was integrated with recycling chromatography. In the light of the results of this work, separation processes based on combining membrane and chromatographic separations could be effectively applied for different biorefinery applications. The main challenge remains in the development of inexpensive separation materials which are resistant towards harsh process conditions and fouling.

Effect of additives, precursors and process conditions on particle morphology

The objective of the thesis was to develop methods to manufacture and control calcium carbonate crystal nucleation and growth in precipitation process. The work consists of experimental part and literature part that addresses theory of nucleation, crystallization and precipitation. In the experimental part calcium carbonate was precipitated using carbonization reaction. Precipitation was carried out in presence of known morphology controlling agents (anionic polymers and sodium silicate) and by using different operation conditions. Formed material was characterized using SEM images, and its thermal stability was assessed. This work demonstrates that carbon dioxide feeding rate and concentrations of calcium hydroxide and additives can be used to control size, shape and amount of precipitating calcium carbonate.

The Combined treatment of UV Light and Titanium Dioxide (TiO2) in Grease Filtration Technique

The aim of this thesis was to identify the best grease removal technique with the application of low power of UV light to TiO2 coated grease filters. The treatment with various power series of ozone generating and ozone free lamps to normal grease filters and TiO2 coated grease filters were examined and the obtained results are compared to each other in this paper. The effect of ozone reaction was observed and compared with the effect of TiO2. The experiments were solely based on the photo oxidation and photo catalytic oxidation reactions. TiO2 is a green catalyst used in the photocatalytic reaction. Sunflower oil was used for grease production and tetracholoroethylene as a solvent. Grease samples were collected from the ventilation duct connected to the cooking hood system. Sample extraction was done in ultrasonic bath with the principle of sonication. The sample analysis was done by FTIR machine. The result determining the concentration of grease was the quantification of saturated C-H bonds in the chosen peak group of the spectrum. A very low power of UVC light functions perfectly with the Titanium dioxide. The experimental results have shown the combined treatment of titanium dioxide and UV light is an effective method in grease removal process. The photocatalytic reaction with titanium dioxide is better than photo oxidation reaction with ozone treatment. Photocatalytic reaction is environmentally friendly, energy efficient and economical.

“Why share in uncertain conditions?” Factors of individual level knowledge sharing in offshoring cases

The objective of this Master’s Thesis was to research factors influencing and enhancing individual level knowledge sharing in offshore projects which often involve uncertainty of the knowledge provider’s own future. The purpose was to understand why individuals are willing to share their knowledge under these kinds of circumstances. In addition the goal was to identify obstacles to interpersonal knowledge sharing in order to understand how to mitigate their influence. The research was conducted as a qualitative multiple case study in a global IT company, and the data was gathered using semi-structured personal theme interviews within two different offshore projects. In order to a gain a wider perspective on the matter, some management representatives were interviewed as well. Data was analysed with the inductive content analysis method. Results of the study indicate that individuals are willing to share their knowledge despite of uncertainty if they are motivated, if they are provided with opportunities to do so, and if they have skills, competence and experience to share their knowledge. A strong knowledge sharing culture in the organization or team also works as a strong incentive for individual level knowledge sharing. The findings suggest that even under uncertain conditions it is possible to encourage people to share their knowledge if uncertainty can be decreased to a bearable level, a robust and personal connection and relationship between the knowledge provider and acquirer can be created and suitable opportunities for knowledge sharing are provided. In addition, based on the results the support and commitment of management and HR in addition to favourable environmental circumstances play an essential role in building a bridge between the knowledge provider and acquirer in order to create a virtual environment and space for knowledge sharing: Ba.

Ravinnepitoisen teollisen jäteveden tuotteistaminen

Tässä työssä selvitettiin ravinnepitoisen jäteveden väkevöintiä erityisesti ammoniumtypen ja orgaanisten happojen osalta. Konsentrointiin käytettiin pääasiassa käänteisosmoosia sekä haihdutusta, mutta myös nanosuodatusta tutkittiin. Jätevesi oli Honkajoki Oy:n lauhdevettä. Kirjallisuusosassa esiteltiin Honkajoki Oy:n toimintaa, membraanierotus-prosesseja, lihantuotannossa syntyvän jätteen ominaisuuksia sekä sen puhdistamista. Keskeisimmät suodatukset tehtiin DOW FILMTEC SW30HR -membraanilla, ja käytetty laitteisto oli DSS LabStak M20. Suodatuksia tehtiin eri pH-olosuhteissa typen ja orgaanisten happojen erottumisen kannalta optimaalisten olosuhteiden löytämiseksi. Lisäksi tutkittiin, kuinka puhtaaksi permeaatti voidaan saada uudelleensuodatuksen avulla. Työssä käytettiin myös haihdutusta lauhteen väkevöintiin. Ammoniumtypen konsentroituminen suodatuksissa oli tehokkainta pH:n ollessa 7 tai sen alle. Kaksivaiheisella suodatuksella permeaatin laatu alitti selvästi Karvianjokeen laskettaville jätevesille asetetut laatu- ja kuormitusrajat. Yhdistämällä suodatus- ja haihdutusprosessit, pystyttiin valmistamaan liuosta, jonka ammoniumtyppipitoisuus oli noin 7,6 %. Tuolloin suodatus tehtiin pH 7:ssä ja haihdutus pH 3:ssa rotavaporilla 26 mbar paineessa ja 50 °C lämpötilassa. Syöttöliuoksen tilavuuden alenema oli noin 65-kertainen. Haihdutuksessa muodostuneessa lauhteessa oli paljon orgaanisia happoja ja käytännössä ei lainkaan ammoniumtyppeä. Tuotejakeita saatiin siten kaksi kappaletta: ammoniumtyppijae ja orgaanisia happoja sisältävä jae.

Conditions and practices in the commercialisation of innovations in wood industry

The report 'Conditions and practices in the commercialisation of innovation in wood industry' has been written as a part of the Wood Academy project. The report analyses the commercialisation conditions and practices of wood industry by utilising product categorisation based on a conceptual schema which combines the aspects of the transfer of the procession of utility and the degree of form/service utility (or value-added) created or provided by the company. Open innovation approaches help to perceive the possible new product and service innovations as well as the new business models and earning logics in the industry. The report also contains brief company cases to demonstrate theory-to-practice and showcase company examples from successful Finnish companies.

Maximizing of water recovery in nanofiltration of mine process waters by using antiscalants

Reverse osmosis and nanofiltration are among the most effective and widely used desalination and water softening technologies. They can also be used to treat mining wastewaters and are capable of producing water of extremely high purity, regardless of the high concentrations of toxic heavy metals and extreme pH and salinity. However, challenges with recovering the salts and metals from mining wastewaters in exploitable form, as well as problems with scaling still limit the process efficiency and the ratio of purified water recoverable from process waters. To address the problem of membrane scaling caused by calcium sulfate, batch filtration experiments with the Desal-5 DL nanofiltration membrane, three commercial antiscalants and actual mine process water from a copper mine were performed. The aim of these experiments was to find process conditions where maximum water recovery would be achieved before significant scaling or irreversible membrane fouling would occur and to further improve water recovery by addition of antiscalants. Water recovery of 70 % was reached with the experimental setups by optimizing process conditions. PC-504T antiscaling agent was determined to be the most effective of the three antiscalants used and the addition of 5 ppm of PC-504T allowed the water recovery to be further increased from 70 % to 85 % before major scaling was observed. In these conditions 92 % calcium rejection was achieved.

Customer´s perceptions of value during the lifecycle of concentrate filtration

The objective of this study was to examine how customers purchase complex industrial solutions in mining industry, and what kind of value they perceive during different phases of the solution life cycle. In addition, a systematic method for understanding customer value was developed, which can be applied for other company’s offerings as well. The method includes step-by-step instructions for 1) the collection of customer value data and 2) implementation of the findings. The theoretical part of the study focuses on solution and customer value literature in business-to-business markets. In this study qualitative embedded multiple-case study was used as a research method. The primary data was collected through in-depth interviews in two market areas and by participating in customer meetings as an external observer. The results show that there are two ways of buying solutions that needs to be treated individually. Customers prefer to buy solutions from engineering companies as they think that suppliers still need to work on their solution capabilities. Therefore, Outotec should focus more on marketing itself as a solution provider. Customers buy solutions that create the most value with the lowest risk and they need to be supported throughout the solution lifecycle. References that demonstrate previous experience are the most effective way to reduce customers’ risk. However, the customer-perceived values and challenges differ between the market areas, and thus, suppliers should have divergent strategies for specific market areas.

Effect of ambient conditions on dimensional stability and stiffness of commercial paperboard and paperboard trays

The objective of this study was to develop laboratory test methods for characterizing the effects of changed moisture content on paperboard trays produced by press-forming process. Influence of moisture on the properties of unconverted paperboard such as bending stiffness, bursting strength, and curling was studied. Paperboard and tray samples were tested after storing in different relative humidity conditions (35, 50, 65, 80 and 95% RH). The effect of PE and PET extrusion coatings on these properties was also studied. It was found that increase in moisture content of paperboard decreases bending and bursting strength, dimensional stability and stiffness of paperboard trays. Such physical and mechanical properties as bending stiffness and curling of paperboard seem to define the stiffness of ready-made trays and their dimensional stability. Paperboards and trays with extruded PE and PET one sided coatings demonstrated higher strength properties but at the same time had lower dimensional stability comparing to uncoated paperboards. Samples with smaller polymer coat weight had better dimensional stability than respective samples with higher coat weight. It was also found that preconditioning of paperboard in lower humidity environment before press-forming could improve dimensional stability and stiffness of ready-made tray.

Doubly fed wind turbine performance in variable grid conditions

Wind turbines based on doubly fed induction generators (DFIG) become the most popular solution in high power wind generation industry. While this topology provides great performance with the reduced power rating of power converter, it has more complicated structure in comparison with full-rated topologies, and therefore leads to complexity of control algorithms and electromechanical processes in the system. The purpose of presented study is to present a proper vector control scheme for the DFIG and overall control for the WT to investigate its behavior at different wind speeds and in different grid voltage conditions: voltage sags, magnitude and frequency variations. The key principles of variable-speed wind turbine were implemented in simulation model and demonstrated during the study. Then, based on developed control scheme and mathematical model, the set of simulation is made to analyze reactive power capabilities of the DFIG wind turbine. Further, the rating of rotor-side converter is modified to not only generate active rated active power, but also to fulfill Grid Codes. Results of modelling and analyzing of the DFIG WT behavior under different speeds and different voltage conditions are presented in the work.