Development of a process for the direct synthesis of hydrogen peroxide in a novel microstructured reactor

Microreactors have proven to be versatile tools for process intensification. Over recent decades, they have increasingly been used for product and process development in chemical industries. Enhanced heat and mass transfer in the reactors due to the extremely high surfacearea- to-volume ratio and interfacial area allow chemical processes to be operated at extreme conditions. Safety is improved by the small holdup volume of the reactors and effective control of pressure and temperature. Hydrogen peroxide is a powerful green oxidant that is used in a wide range of industries. Reduction and auto-oxidation of anthraquinones is currently the main process for hydrogen peroxide production. Direct synthesis is a green alternative and has potential for on-site production. However, there are two limitations: safety concerns because of the explosive gas mixture produced and low selectivity of the process. The aim of this thesis was to develop a process for direct synthesis of hydrogen peroxide utilizing microreactor technology. Experimental and numerical approaches were applied for development of the microreactor. Development of a novel microreactor was commenced by studying the hydrodynamics and mass transfer in prototype microreactor plates. The prototypes were designed and fabricated with the assistance of CFD modeling to optimize the shape and size of the microstructure. Empirical correlations for the mass transfer coefficient were derived. The pressure drop in micro T-mixers was investigated experimentally and numerically. Correlations describing the friction factor for different flow regimes were developed and predicted values were in good agreement with experimental results. Experimental studies were conducted to develop a highly active and selective catalyst with a proper form for the microreactor. Pd catalysts supported on activated carbon cloths were prepared by different treatments during the catalyst preparation. A variety of characterization methods were used for catalyst investigation. The surface chemistry of the support and the oxidation state of the metallic phase in the catalyst play important roles in catalyst activity and selectivity for the direct synthesis. The direct synthesis of hydrogen peroxide was investigated in a bench-scale continuous process using the novel microreactor developed. The microreactor was fabricated based on the hydrodynamic and mass transfer studies and provided a high interfacial area and high mass transfer coefficient. The catalysts were prepared under optimum treatment conditions. The direct synthesis was conducted at various conditions. The thesis represents a step towards a commercially viable direct synthesis. The focus is on the two main challenges: mitigating the safety problem by utilization of microprocess technology and improving the selectivity by catalyst development.

Stock Price Reactions on M&A, Dividends and Game Releases. Evidence from Gaming Industry.

A rapidly growing gaming industry, which specializes on PC, console, online and other games, attracts attention of investors and analysts, who try to understand what drives changes of the gaming industry companies’ stock prices. This master thesis shows the evidence that, besides long-established types of events (M&A and dividend payments), the companies’ stock price changes depend on industry-specific events. I analyzed specific for gaming industry events - game releases with respect to its subdivisions: new games-sequels, games ratings and subdivision according to a developer of a game (self-developed by publisher or outsourced). The master thesis analyzes stock prices of 55 companies from gaming industry from all over the world. The research period covers 5 year, spreading from April 2008 to April 2013. Executed with an event study method, results of the research show that all the analyzed events types have significant influence on the stock prices of the gaming industry companies. The current master thesis suggests that acquisitions in the industry affect positively bidders’ and targets’ stock prices. Mergers events cause positive stock price reactions as well. But dividends payments and game releases events influence negatively on the stock prices. Game releases’ effect is up to -2.2% of cumulative average abnormal return (CAAR) drop during the first ten days after the game releases. Having researched different kinds of events and identified the direction of their impact, the current paper can be of high value for investors, seeking profits in the gaming industry, and other interested parties.

Virulence properties of Aggregatibacter actinomycetemcomitans biofilm and characterisation of its putative cytokine exploitation

Biofilms are surface-attached multispecies microbial communities that are embedded by their self-produced extracellular polymeric substances. This lifestyle enhances the survival of the bacteria and plays a major role in many chronic bacterial infections. For instance, periodontitis is initiated by multispecies biofilms. The phases of active periodontal tissue destruction and notably increased levels of proinflammatory mediators, such as the key inflammatory mediator interleukin (IL)-1beta, are typical of the disease. The opportunistic periodontal pathogen Aggregatibacter actinomycetemcomitans is usually abundant at sites of aggressive periodontitis. Despite potent host immune system responses to subgingival invaders, A. actinomycetemcomitans is able to resist clearance attempts. Moreover, some strains of A. actinomycetemcomitans can generate genetic diversity through natural transformation, which may improve the species’ adjustment tothe subgingival environment in the long term. Some biofilm forming species are known to bind and sense human cytokines. As a response to cytokines, bacteria may increase biofilm formation and alter their expression of virulence genes. Specific outer membrane receptors for interferon-γ or IL-1β have been characterised in two Gram-negative pathogens. Because little is known about periodontal pathogens’ ability to sense cytokines, we used A. actinomycetemcomitans as a model organism to investigate how the species responds to IL-1beta. The main aims of this thesis were to explore cytokine binding on single-species A. actinomycetemcomitans biofilms and to determine the effects of cytokines on the biofilm formation and metabolic activity of the species. Additionally, the cytokine’s putative internalisation and interaction with A. actinomycetemcomitans proteins were studied. The possible impact of biofilm IL-1beta sequestering on the proliferation and apoptosis of gingival keratinocyte cells was evaluated in an organotypic mucosa co-culture model. Finally, the role of the extramembranous domain of the outer membrane protein HofQ (emHofQ) in DNA binding linked to DNA uptake in A. actinomycetemcomitans was examined. Our main finding revealed that viable A. actinomycetemcomitans biofilms can bind and take up the IL-1β produced by gingival cells. At the sites of pathogen-host interaction, the proliferation and apoptosis of gingival keratinocytes decreased slightly. Notably, the exposure of biofilms to IL-1beta caused their metabolic activity to drop, which may be linked to the observed interaction of IL-1beta with the conserved intracellular proteins DNA binding protein HU and the trimeric form of ATP synthase subunit beta. A Pasteurellaceaespecific lipoprotein, which had no previously determined function, was characterized as an IL-1beta interacting membrane protein that was expressed in the biofilm cultures of all tested A. actinomycetemcomitans strains. The use of a subcellular localisation tool combined with experimental analyses suggested that the identified lipoprotein, bacterial interleukin receptor I (BilRI), may be associated with the outer membrane with a portion of the protein oriented towards the external milieu. The results of the emHofQ study indicated that emHofQ has both the structural and functional capability to bind DNA. This result implies that emHofQ plays a role in DNA assimilation. The results from the current study also demonstrate that the Gram-negative oral species appears to sense the central proinflammatory mediator IL-1beta.

Optimization of parameters for fiber laser-MAG hybrid welding in shipbuilding applications

The Arctic region becoming very active area of the industrial developments since it may contain approximately 15-25% of the hydrocarbon and other valuable natural resources which are in great demand nowadays. Harsh operation conditions make the Arctic region difficult to access due to low temperatures which can drop below -50 °C in winter and various additional loads. As a result, newer and modified metallic materials are implemented which can cause certain problems in welding them properly. Steel is still the most widely used material in the Arctic regions due to high mechanical properties, cheapness and manufacturability. Moreover, with recent steel manufacturing development it is possible to make up to 1100 MPa yield strength microalloyed high strength steel which can be operated at temperatures -60 °C possessing reasonable weldability, ductility and suitable impact toughness which is the most crucial property for the Arctic usability. For many years, the arc welding was the most dominant joining method of the metallic materials. Recently, other joining methods are successfully implemented into welding manufacturing due to growing industrial demands and one of them is the laser-arc hybrid welding. The laser-arc hybrid welding successfully combines the advantages and eliminates the disadvantages of the both joining methods therefore produce less distortions, reduce the need of edge preparation, generates narrower heat-affected zone, and increase welding speed or productivity significantly. Moreover, due to easy implementation of the filler wire, accordingly the mechanical properties of the joints can be manipulated in order to produce suitable quality. Moreover, with laser-arc hybrid welding it is possible to achieve matching weld metal compared to the base material even with the low alloying welding wires without excessive softening of the HAZ in the high strength steels. As a result, the laser-arc welding methods can be the most desired and dominating welding technology nowadays, and which is already operating in automotive and shipbuilding industries with a great success. However, in the future it can be extended to offshore, pipe-laying, and heavy equipment industries for arctic environment. CO2 and Nd:YAG laser sources in combination with gas metal arc source have been used widely in the past two decades. Recently, the fiber laser sources offered high power outputs with excellent beam quality, very high electrical efficiency, low maintenance expenses, and higher mobility due to fiber optics. As a result, fiber laser-arc hybrid process offers even more extended advantages and applications. However, the information about fiber or disk laser-arc hybrid welding is very limited. The objectives of the Master’s thesis are concentrated on the study of fiber laser-MAG hybrid welding parameters in order to understand resulting mechanical properties and quality of the welds. In this work only ferrous materials are reviewed. The qualitative methodological approach has been used to achieve the objectives. This study demonstrates that laser-arc hybrid welding is suitable for welding of many types, thicknesses and strength of steels with acceptable mechanical properties along very high productivity. New developments of the fiber laser-arc hybrid process offers extended capabilities over CO2 laser combined with the arc. This work can be used as guideline in hybrid welding technology with comprehensive study the effect of welding parameter on joint quality.

Modeling of Liquid-Solid Flow in Industrial Scale

In the present work, liquid-solid flow in industrial scale is modeled using the commercial software of Computational Fluid Dynamics (CFD) ANSYS Fluent 14.5. In literature, there are few studies on liquid-solid flow in industrial scale, but any information about the particular case with modified geometry cannot be found. The aim of this thesis is to describe the strengths and weaknesses of the multiphase models, when a large-scale application is studied within liquid-solid flow, including the boundary-layer characteristics. The results indicate that the selection of the most appropriate multiphase model depends on the flow regime. Thus, careful estimations of the flow regime are recommended to be done before modeling. The computational tool is developed for this purpose during this thesis. The homogeneous multiphase model is valid only for homogeneous suspension, the discrete phase model (DPM) is recommended for homogeneous and heterogeneous suspension where pipe Froude number is greater than 1.0, while the mixture and Eulerian models are able to predict also flow regimes, where pipe Froude number is smaller than 1.0 and particles tend to settle. With increasing material density ratio and decreasing pipe Froude number, the Eulerian model gives the most accurate results, because it does not include simplifications in Navier-Stokes equations like the other models. In addition, the results indicate that the potential location of erosion in the pipe depends on material density ratio. Possible sedimentation of particles can cause erosion and increase pressure drop as well. In the pipe bend, especially secondary flows, perpendicular to the main flow, affect the location of erosion.

Sustainable linguistic repository built on DSpace

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Irtoamispäivän kurssilaskusuhteet, epänormaalit tuotot sekä epänormaalit kaupankäyntivolyymit vuosina 2005-2013

Tutkielman tavoitteena on tutkia osingon irtoamispäivän tapahtumia OMX Helsinki 25:n yrityksillä vuosina 2005–2013. Vallitsevan käsityksen mukaan osakkeen hinta laskee irtoamispäivänä osingon verran +/- markkinoiden yleisestä hintamuutoksesta johtuva nousu/lasku. Käsitystä on pyritty murtamaan vuosien saatossa neljän eri teorian avulla, jotka ovat veroasiakaskuntateoria, lyhytaikaisen vaihdon hypoteesi, dynaaminen malli sekä mikrorakenneteoria. Osingon irtoamispäivää tarkastellaan kolmen eri tutkimuksen avulla ja saatuja tuloksia verrataan teoriaan sekä aikaisempiin löydöksiin. Tutkimusosuudet ovat kurssilaskusuhteet, epänormaalit tuotot sekä epänormaalit kaupankäyntivolyymit. Kurssilaskusuhdetta tarkastellaan vertaamalla cum-päivän ja irtoamispäivän osakkeiden hintojen erotusta maksetun osingon määrään. Epänormaaleja tuottoja ja epänormaaleja kaupankäyntivolyymejä tarkastellaan tapahtumatutkimus-menetelmällä viisi päivää ennen ja viisi päivää jälkeen osingon irtoamisen. Kurssilaskusuhteet olivat eri tavoilla laskettuina 77 – 94 %. Irtoamispäivän ympärillä oli havaittavissa 1,5 %:n negatiivisia epänormaaleja tuottoja. Epänormaalit kaupankäyntivolyymit kasvoivat tasaisesti lähestyttäessä irtoamispäivää ja olivat voimakkaimmillaan irtoamispäivänä. Irtoamispäivän jälkeen kaupankäyntivolyymit palautuivat hiljalleen normaalille tasolle. Tulokset vastaavat aikaisempia löydöksiä kurssilaskusuhteita ja epänormaaleja volyymejä tarkasteltaessa, mutta eroavat epänormaaleissa tuotoissa.

Liquid cooling solutions for rotating permanent magnet synchronous machines

In the design of electrical machines, efficiency improvements have become very important. However, there are at least two significant cases in which the compactness of electrical machines is critical and the tolerance of extremely high losses is valued: vehicle traction, where very high torque density is desired at least temporarily; and direct-drive wind turbine generators, whose mass should be acceptably low. As ever higher torque density and ever more compact electrical machines are developed for these purposes, thermal issues, i.e. avoidance of over-temperatures and damage in conditions of high heat losses, are becoming of utmost importance. The excessive temperatures of critical machine components, such as insulation and permanent magnets, easily cause failures of the whole electrical equipment. In electrical machines with excitation systems based on permanent magnets, special attention must be paid to the rotor temperature because of the temperature-sensitive properties of permanent magnets. The allowable temperature of NdFeB magnets is usually significantly less than 150 ˚C. The practical problem is that the part of the machine where the permanent magnets are located should stay cooler than the copper windings, which can easily tolerate temperatures of 155 ˚C or 180 ˚C. Therefore, new cooling solutions should be developed in order to cool permanent magnet electrical machines with high torque density and because of it with high concentrated losses in stators. In this doctoral dissertation, direct and indirect liquid cooling techniques for permanent magnet synchronous electrical machines (PMSM) with high torque density are presented and discussed. The aim of this research is to analyse thermal behaviours of the machines using the most applicable and accurate thermal analysis methods and to propose new, practical machine designs based on these analyses. The Computational Fluid Dynamics (CFD) thermal simulations of the heat transfer inside the machines and lumped parameter thermal network (LPTN) simulations both presented herein are used for the analyses. Detailed descriptions of the simulated thermal models are also presented. Most of the theoretical considerations and simulations have been verified via experimental measurements on a copper tooth-coil (motorette) and on various prototypes of electrical machines. The indirect liquid cooling systems of a 100 kW axial flux (AF) PMSM and a 110 kW radial flux (RF) PMSM are analysed here by means of simplified 3D CFD conjugate thermal models of the parts of both machines. In terms of results, a significant temperature drop of 40 ̊C in the stator winding and 28 ̊C in the rotor of the AF PMSM was achieved with the addition of highly thermally conductive materials into the machine: copper bars inserted in the teeth, and potting material around the end windings. In the RF PMSM, the potting material resulted in a temperature decrease of 6 ̊C in the stator winding, and in a decrease of 10 ̊C in the rotor embedded-permanentmagnets. Two types of unique direct liquid cooling systems for low power machines are analysed herein to demonstrate the effectiveness of the cooling systems in conditions of highly concentrated heat losses. LPTN analysis and CFD thermal analysis (the latter being particularly useful for unique design) were applied to simulate the temperature distribution within the machine models. Oil-immersion cooling provided good cooling capability for a 26.6 kW PMSM of a hybrid vehicle. A direct liquid cooling system for the copper winding with inner stainless steel tubes was designed for an 8 MW directdrive PM synchronous generator. The design principles of this cooling solution are described in detail in this thesis. The thermal analyses demonstrate that the stator winding and the rotor magnet temperatures are kept significantly below their critical temperatures with demineralized water flow. A comparison study of the coolant agents indicates that propylene glycol is more effective than ethylene glycol in arctic conditions.

Study of Control Methods of a High-Frequency Cycloconverter for Domestic Induction Heating Appliances

A high-frequency cyclonverter acts as a direct ac-to-ac power converter circuit that does not require a diode bidge rectifier. Bridgeless topology makes it possible to remove forward voltage drop losses that are present in a diode bridge. In addition, the on-state losses can be reduced to 1.5 times the on-state resistance of switches in half-bridge operation of the cycloconverter. A high-frequency cycloconverter is reviewed and the charging effect of the dc-capacitors in ``back-to-back'' or synchronous mode operation operation is analyzed. In addition, a control method is introduced for regulating dc-voltage of the ac-side capacitors in synchronous operation mode. The controller regulates the dc-capacitors and prevents switches from reaching overvoltage level. This can be accomplished by variating phase-shift between the upper and the lower gate signals. By adding phase-shift between the gate signal pairs, the charge stored in the energy storage capacitors can be discharged through the resonant load and substantially, the output resonant current amplitude can be improved. The above goals are analyzed and illustrated with simulation. Theory is supported with practical measurements where the proposed control method is implemented in an FPGA device and tested with a high-frequency cycloconverter using super-junction power MOSFETs as switching devices.

Simulation of wind powered hydraulic heating system

The objective of this master’s thesis was to design and simulate a wind powered hydraulic heating system that can operate independently in remote places where the use of electricity is not possible. Components for the system were to be selected in such a way that the conditions for manufacture, use and economic viability are the as good as possible. Savonius rotor was chosen for wind turbine, due to its low cut in speed and robust design. Savonius rotor produces kinetic energy in wide wind speed range and it can withstand high wind gusts. Radial piston pump was chosen for the flow source of the hydraulic heater. Pump type was selected due to its characteristics in low rotation speeds and high efficiency. Volume flow from the pump is passed through the throttle orifice. Pressure drop over the orifice causes the hydraulic oil to heat up and, thus, creating thermal energy. Thermal energy in the oil is led to radiator where it conducts heat to the environment. The hydraulic heating system was simulated. For this purpose a mathematical models of chosen components were created. In simulation wind data gathered by Finnish meteorological institute for 167 hours was used as input. The highest produced power was achieved by changing the orifice diameter so that the rotor tip speed ratio follows the power curve. This is not possible to achieve without using electricity. Thus, for the orifice diameter only one, the optimal value was defined. Results from the simulation were compared with investment calculations. Different parameters effecting the investment profitability were altered in sensitivity analyses in order to define the points of investment profitability. Investment was found to be profitable only with high average wind speeds.

Puuperäiset polymeerit synteettisten sideaineiden korvaajina

Tämän kandidaatintyön aiheena oli löytää biojalostamon näkökulmasta käyttökelpoisia tuotantoreittejä puuperäisistä materiaaleista bioperäisiin kemikaaleihin, joilla olisi mahdollista korvata synteettisiä sideaineita. Tällä hetkellä suurin osa sideaineista ja päällystemateriaaleista tuotetaan uusiutumattomista luonnonvaroista, kuten maakaasusta ja öljystä. Lopputuotteiden kierrätettävyyden ja vihreyden ohella yksi metsäteollisuuden tulevaisuuden trendejä on pyrkiä irti öljy- ja maakaasuriippuvuudesta. Muutoksella voidaan säästää sekä ympäristöä, että rahaa. Biopohjaisilla drop-in kemikaaleilla ja muilla biopohjaisilla vaihtoehdoilla tämä on mahdollista Tässä työssä tutkittiin ja havainnollistettiin mahdollisin tuotantoreitein useiden tällä hetkellä käytössä olevien sideaineiden korvaamista biopohjaisilla versioilla. Työ tehtiin kirjallisuustutkielmana, eikä siihen kuulunut laboratoriokokeita. Työn ensimmäisessä osassa painopiste on biojalostamossa ja dispersiopäällystyksessä. Toisessa osassa esitellään tällä hetkellä käytettyjä sideaineita ja niiden mahdollisia biopohjaisia korvaajia tuotantoreitteineen. Työn toissijainen tarkoitus oli selvittää lyhyesti mitä muita puuperäisiä komponentteja voidaan käyttää suoraan paperin ja kartongin päällystämiseen. Viimeiseksi on esitelty vielä lyhyesti kaupallisesti käytössä olevia biomuoveja ja päällysteitä.

Teollinen öljyn erotus koalesenssisuodatuksella väliaineessa

Koalesenssi on ilmiö, jossa dispergoidun faasin pisarat pyrkivät muodostamaan suurempia pisaroita kunnes erotettava faasi muodostuu. Koalesenssi tapahtuu kolmessa päävaiheessa, jotka ovat lähestyminen, kiinnittyminen ja irrotus. Lähestymiseen vaikuttavat mekanismit ovat muuan muassa sieppaus, diffuusio, törmäysvaikutus, sedimentaatio, sähköiset repul-siovoimat ja van der Waalsin voimat. Kiinnittymisvaiheessa dispergoidun faasin pisarat syrjäyttävät väliaineen nestekalvon samalla kostuttaen väliaineen pinnan. Irrotusvaiheessa pisaran hydrodynaaminen voima voittaa pisaran ja väliaineen välisen adheesiovoiman. Koalesenssin tehokkuuteen vaikuttavat useat eri parametrit kuten virtausnopeus, pedin ominaisuudet, väliaineen ominaisuudet sekä emulsion ominaisuudet. Nämä kaikki asiat tulee ottaa huomioon koalesenssisuodatuksen suunnittelussa. Koalesenssisuodatus lukeutuu syväsuodatusmenetelmiin, jotka on ollut käytössä jo yli 100 vuotta. Koalesenssisuodatusmenetelmä on tehokas menetelmä pienten pisaroiden erottami-seen. Menetelmää käytetään esimerkiksi öljyisten jätevesien puhdistuksessa. Teollisen öljyn syväsuodatuksen etuihin kuuluu muun muassa sen kompakti koko, alhaisemmat käyt-tökustannukset, korkea erotusaste, kyky erotella pienetkin pisarat sekä helppo operointi, automatisointi ja huolto. Suurin haittapuoli on kuitenkin väliaineen tukkeutuminen, joten prosessi vaatii puhdistuksen tai väliaineen uusimisen. Tämän kandidaatintyön tarkoituksena oli koota kirjallisuustyö öljyn koalesenssisuodatuk-sesta. Työssä kartoitettiin koalesenssisuodatuksen lähtökohdat, teoria, tärkeimmät teolli-suuden sovellukset sekä väliaineet.

Kerrostalon kiinteistösähkönkulutuksen kompensointi aurinkosähköjärjestelmällä

Aurinkopaneeleiden hinta on laskenut reilusti viime vuosien aikana. Hinnan laskun seurauksena aurinkosähköjärjestelmiä on asennettu paljon yksityisiin rakennuksiin sekä Suomessa että muualla maailmassa. Tässä kandidaatintyössä tutkitaan kerrostalon kiinteistösähkönkulutuksen kompensointia aurinkosähköjärjestelmällä. Kompensointia tutkitaan, koska näin saadaan taloudellisesti paras hyöty aurinkosähköjärjestelmästä. Kerrostalon kiinteistösähkönkulutuksella tarkoitetaan talon teknisten järjestelmien kuluttamaa sähköä. Järjestelmän sijoitusta tutkitaan katolle ja parvekekaiteisiin. Katolle sijoitettuna aurinkopaneelien tuotantoa tutkitaan siten, että paneelit ovat asennettu 45° ja 15° tasokulmaan. Aurinkosähköjärjestelmän investoinnin kannattavuutta tutkitaan taloyhtiön näkökulmasta.

Modeling a Network of Heat Exchangers

This research work addresses the problem of building a mathematical model for the given system of heat exchangers and to determine the temperatures, pressures and velocities at the intermediate positions. Such model could be used in nding an optimal design for such a superstructure. To limit the size and computing time a reduced network model was used. The method can be generalized to larger network structures. A mathematical model which includes a system of non-linear equations has been built and solved according to the Newton-Raphson algorithm. The results obtained by the proposed mathematical model were compared with the results obtained by the Paterson approximation and Chen's Approximation. Results of this research work in collaboration with a current ongoing research at the department will optimize the valve positions and hence, minimize the pumping cost and maximize the heat transfer of the system of heat exchangers.

Öljy-vesiemulsioiden erottumisen tehostaminen erilaisten geometrioiden avulla

Työn kirjallisuusosassa selvitettiin neste-nestedispersioiden ja emulsioiden pisarakokojakauman määrittämiseen soveltuvia menetelmiä. Kirjallisuusosa painottuu emulsioiden stabiliteettiin liittyvään teoriaan ja menetelmiin, joilla voidaan tutkia pisarakokojakaumia suoraan prosessista. Erillisnäytteiden analysointiin perustuvista menetelmistä on esitettynä mikroskooppianalyysi sekä lasersäteen sirontaan perustuva mittaus, joita molempia käytettiin tämän työn kokeellisessa osassa. Kokeellisessa osassa pyrittiin selvittämään, vaikuttavatko kaksi erimuotoista ruuvi-kapaletta eri tavalla öljy-vesiemulsion pisarakokojakaumaan, kun emulsio virtasi ruuvin vuorovaikutusalueen läpi. Tätä tutkittiin määrittämällä ennen vuorovaikutusaluetta ja vuorovaikutusalueen jälkeen kerättyjen emulsionäytteiden pisarakokojakaumat lasersäteen sirontamittauksilla. Mitattujen pisarakokojakaumien perusteella ei voitu tehdä varmaa johtopäätöstä, vaikuttivatko ruuvit pisarakokojakaumaan vai eivät. Syynä tähän on pisarakokojakaumien vaihtelu rinnakkaisnäytteissä. Rinnakkaismittauksissa havaittu vaihtelu johtui arvaamattomasti muuttuneista virtausolosuhteista, mikä aiheutti edelleen öljypitoisuuden muutoksia. Muita mahdollisia syitä ovat veden ionivahvuuden, pH:n ja lämpötilan vaihtelu.