Variable speed drive in fan system monitoring

Fan systems are responsible for approximately 10% of the electricity consumption in industrial and municipal sectors, and it has been found that there is energy-saving potential in these systems. To this end, variable speed drives (VSDs) are used to enhance the efficiency of fan systems. Usually, fan system operation is optimized based on measurements of the system, but there are seldom readily installed meters in the system that can be used for the purpose. Thus, sensorless methods are needed for the optimization of fan system operation. In this thesis, methods for the fan operating point estimation with a variable speed drive are studied and discussed. These methods can be used for the energy efficient control of the fan system without additional measurements. The operation of these methods is validated by laboratory measurements and data from an industrial fan system. In addition to their energy consumption, condition monitoring of fan systems is a key issue as fans are an integral part of various production processes. Fan system condition monitoring is usually carried out with vibration measurements, which again increase the system complexity. However, variable speed drives can already be used for pumping system condition monitoring. Therefore, it would add to the usability of a variablespeed- driven fan system if the variable speed drive could be used as a condition monitoring device. In this thesis, sensorless detection methods for three lifetime-reducing phenomena are suggested: these are detection of the fan contamination build-up, the correct rotational direction, and the fan surge. The methods use the variable speed drive monitoring and control options for the detection along with simple signal processing methods, such as power spectrum density estimates. The methods have been validated by laboratory measurements. The key finding of this doctoral thesis is that a variable speed drive can be used on its own as a monitoring and control device for the fan system energy efficiency, and it can also be used in the detection of certain lifetime-reducing phenomena.

Interfirm Information System for Supply Chain Management from the Cloud: An Exploratory Case Study from the Telecom Industry

This study examines the practice of supply chain management problems and the perceived demand information distortion’s (the bullwhip effect) reduction with the interfirm information system, which is delivered as a cloud service to a company operating in the telecommunications industry. The purpose is to shed light in practice that do the interfirm information system have impact on the performance of the supply chain and in particularly the reduction of bullwhip effect. In addition, a holistic case study of the global telecommunications company's supply chain is presented and also the challenges it’s facing, and this study also proposes some measures to improve the situation. The theoretical part consists of the supply chain and its management, as well as increasing the efficiency and introducing the theories and related previous research. In addition, study presents performance metrics for the bullwhip effect detection and tracking. The theoretical part ends in presenting cloud -based business intelligence theoretical framework used in the background of this study. The research strategy is a qualitative case study, supported by quantitative data, which is collected from a telecommunication sector company's databases. Qualitative data were gathered mainly with two open interviews and the e-mail exchange during the development project. In addition, other materials from the company were collected during the project and the company's web site information was also used as the source. The data was collected to a specific case study database in order to increase reliability. The results show that the bullwhip effect can be reduced with the interfirm information system and with the use of CPFR and S&OP models and in particularly combining them to an integrated business planning. According to this study the interfirm information system does not, however, solve all of the supply chain and their effectiveness -related problems, because also the company’s processes and human activities have a major impact.

The role of nuclear and other conventional power plants in the flexible energy system

This thesis reviews the role of nuclear and conventional power plants in the future energy system. The review is done by utilizing freely accesible publications in addition to generating load duration and ramping curves for Nordic energy system. As the aim of the future energy system is to reduce GHG-emissions and avoid further global warming, the need for flexible power generation increases with the increased share of intermittent renewables. The goal of this thesis is to offer extensive understanding of possibilities and restrictions that nuclear power and conventional power plants have regarding flexible and sustainable generation. As a conclusion, nuclear power is the only technology that is able to provide large scale GHG-free power output variations with good ramping values. Most of the currently operating plants are able to take part in load following as the requirement to do so is already required to be included in the plant design. Load duration and ramping curves produced prove that nuclear power is able to cover most of the annual generation variation and ramping needs in the Nordic energy system. From the conventional power generation methods, only biomass combustion can be considered GHG-free because biomass is considered carbon neutral. CFB combusted biomass has good load follow capabilities in good ramping and turndown ratios. All the other conventional power generation technologies generate GHG-emissions and therefore the use of these technologies should be reduced.

PRODUCT DATA MANAGEMENT FOR FINNISH SMALL AND MEDIUM-SIZED MANUFACTURING ENTERPRISES - Towards a viable information system concept

Product Data Management (PDM) systems have been utilized within companies since the 1980s. Mainly the PDM systems have been used by large companies. This thesis presents the premise that small and medium-sized companies can also benefit from utilizing the Product Data Management systems. Furthermore, the starting point for the thesis is that the existing PDM systems are either too expensive or do not properly respond to the requirements SMEs have. The aim of this study is to investigate what kinds of requirements and special features SMEs, operating in Finnish manufacturing industry, have towards Product Data Management. Additionally, the target is to create a conceptual model that could fulfill the specified requirements. The research has been carried out as a qualitative case study, in which the research data was collected from ten Finnish companies operating in manufacturing industry. The research data is formed by interviewing key personnel from the case companies. After this, the data formed from the interviews has been processed to comprise a generic set of information system requirements and the information system concept supporting it. The commercialization of the concept is studied in the thesis from the perspective of system development. The aim was to create a conceptual model, which would be economically feasible for both, a company utilizing the system and for a company developing it. For this reason, the thesis has sought ways to scale the system development effort for multiple simultaneous cases. The main methods found were to utilize platform-based thinking and a way to generalize the system requirements, or in other words abstracting the requirements of an information system. The results of the research highlight the special features Finnish manufacturing SMEs have towards PDM. The most significant of the special features is the usage of project model to manage the order-to-delivery –process. This differs significantly from the traditional concepts of Product Data Management presented in the literature. Furthermore, as a research result, this thesis presents a conceptual model of a PDM system, which would be viable for the case companies interviewed during the research. As a by-product, this research presents a synthesized model, found from the literature, to abstract information system requirements. In addition to this, the strategic importance and categorization of information systems within companies has been discussed from the perspective of information system customizations.

Expanding a Global Company Management System to An Integrated Coverage of Several Standards

This Master’s thesis examines the implementation of management system standard requirements as integrated in the organization. The aim is to determine how requirements from management system standards ISO 14001:2015 and ISO 9001:2015 can be integrated and implemented into the existing ISO 9001:2008 compliant management system. Research was executed as action research by utilizing an operating model about the integrated use of management system standards created by the International Organization for Standardization. Phases of the operating model were applied to the target organization. The similarity and integration potential of relevant standards were assessed by using comparative matrices. Allocation of the requirements and conformity assessment of the processes was executed by gap analysis. The main results indicate that the requirements of the relevant standards are principally equivalent or have the same kind of purpose. The results also show the most important processes of the target organization in terms of requirement compliance, as well as the requirements which affect the process the most. Prioritizing the compliance achievement of the most important processes and implementation of those requirements that have the most effect create an opportunity for organizations to implement the integrated requirements effectively.

THE COSTS OF RAISING EQUITY RATIO FOR BANKS Evidence from publicly listed banks operating in Finland

The solvency rate of banks differs from the other corporations. The equity rate of a bank is lower than it is in corporations of other field of business. However, functional banking industry has huge impact on the whole society. The equity rate of a bank needs to be higher because that makes the banking industry more stable as the probability of the banks going under will decrease. If a bank goes belly up, the government will be compensating the deposits since it has granted the bank’s depositors a deposit insurance. This means that the payment comes from the tax payers in the last resort. Economic conversation has long concentrated on the costs of raising equity ratio. It has been a common belief that raising equity ratio also increases the banks’ funding costs in the same phase and these costs will be redistributed to the banks customers as higher service charges. Regardless of the common belief, the actual reaction of the funding costs to the higher equity ratio has been studied only a little in Europe and no study has been constructed in Finland. Before it can be calculated whether the higher stability of the banking industry that is caused by the raise in equity levels compensates the extra costs in funding costs, it must be calculated how much the actual increase in the funding costs is. Currently the banking industry is controlled by complex and heavy regulation. To maintain such a complex system inflicts major costs in itself. This research leans on the Modigliani and Miller theory, which shows that the finance structure of a firm is irrelevant to their funding costs. In addition, this research follows the calculations of Miller, Yang ja Marcheggianon (2012) and Vale (2011) where they calculate the funding costs after the doubling of specific banks’ equity ratios. The Finnish banks studied in this research are Nordea and Danske Bank because they are the two largest banks operating in Finland and they both also have the right company form to able the calculations. To calculate the costs of halving their leverages this study used the Capital Asset Pricing Model. The halving of the leverage of Danske Bank raised its funding costs for 16—257 basis points depending on the method of assessment. For Nordea the increase in funding costs was 11—186 basis points when its leverage was halved. On the behalf of the results found in this study it can be said that the doubling of an equity ratio does not increase the funding costs of a bank one by one. Actually the increase is quite modest. More solvent banks would increase the stability of the banking industry enormously while the increase in funding costs is low. If the costs of bank regulation exceeds the increase in funding costs after the higher equity ratio, it can be thought that this is the better way of stabilizing the banking industry rather than heavy regulation.

The Design and Implementation of a SD Card File System

SD card (Secure Digital Memory Card) is widely used in portable storage medium. Currently, latest researches on SD card, are mainly SD card controller based on FPGA (Field Programmable Gate Array). Most of them are relying on API interface (Application Programming Interface), AHB bus (Advanced High performance Bus), etc. They are dedicated to the realization of ultra high speed communication between SD card and upper systems. Studies about SD card controller, really play a vital role in the field of high speed cameras and other sub-areas of expertise. This design of FPGA-based file systems and SD2.0 IP (Intellectual Property core) does not only exhibit a nice transmission rate, but also achieve the systematic management of files, while retaining a strong portability and practicality. The file system design and implementation on a SD card covers the main three IP innovation points. First, the combination and integration of file system and SD card controller, makes the overall system highly integrated and practical. The popular SD2.0 protocol is implemented for communication channels. Pure digital logic design based on VHDL (Very-High-Speed Integrated Circuit Hardware Description Language), integrates the SD card controller in hardware layer and the FAT32 file system for the entire system. Secondly, the document management system mechanism makes document processing more convenient and easy. Especially for small files in batch processing, it can ease the pressure of upper system to frequently access and process them, thereby enhancing the overall efficiency of systems. Finally, digital design ensures the superior performance. For transmission security, CRC (Cyclic Redundancy Check) algorithm is for data transmission protection. Design of each module is platform-independent of macro cells, and keeps a better portability. Custom integrated instructions and interfaces may facilitate easily to use. Finally, the actual test went through multi-platform method, Xilinx and Altera FPGA developing platforms. The timing simulation and debugging of each module was covered. Finally, Test results show that the designed FPGA-based file system IP on SD card can support SD card, TF card and Micro SD with 2.0 protocols, and the successful implementation of systematic management for stored files, and supports SD bus mode. Data read and write rates in Kingston class10 card is approximately 24.27MB/s and 16.94MB/s.

THE COSTS OF RAISING EQUITY RATIO FOR BANKS Evidence from publicly listed banks operating in Finland

The solvency rate of banks differs from the other corporations. The equity rate of a bank is lower than it is in corporations of other field of business. However, functional banking industry has huge impact on the whole society. The equity rate of a bank needs to be higher because that makes the banking industry more stable as the probability of the banks going under will decrease. If a bank goes belly up, the government will be compensating the deposits since it has granted the bank’s depositors a deposit insurance. This means that the payment comes from the tax payers in the last resort. Economic conversation has long concentrated on the costs of raising equity ratio. It has been a common belief that raising equity ratio also increases the banks’ funding costs in the same phase and these costs will be redistributed to the banks customers as higher service charges. Regardless of the common belief, the actual reaction of the funding costs to the higher equity ratio has been studied only a little in Europe and no study has been constructed in Finland. Before it can be calculated whether the higher stability of the banking industry that is caused by the raise in equity levels compensates the extra costs in funding costs, it must be calculated how much the actual increase in the funding costs is. Currently the banking industry is controlled by complex and heavy regulation. To maintain such a complex system inflicts major costs in itself. This research leans on the Modigliani and Miller theory, which shows that the finance structure of a firm is irrelevant to their funding costs. In addition, this research follows the calculations of Miller, Yang ja Marcheggianon (2012) and Vale (2011) where they calculate the funding costs after the doubling of specific banks’ equity ratios. The Finnish banks studied in this research are Nordea and Danske Bank because they are the two largest banks operating in Finland and they both also have the right company form to able the calculations. To calculate the costs of halving their leverages this study used the Capital Asset Pricing Model. The halving of the leverage of Danske Bank raised its funding costs for 16—257 basis points depending on the method of assessment. For Nordea the increase in funding costs was 11—186 basis points when its leverage was halved. On the behalf of the results found in this study it can be said that the doubling of an equity ratio does not increase the funding costs of a bank one by one. Actually the increase is quite modest. More solvent banks would increase the stability of the banking industry enormously while the increase in funding costs is low. If the costs of bank regulation exceeds the increase in funding costs after the higher equity ratio, it can be thought that this is the better way of stabilizing the banking industry rather than heavy regulation.