Improving the competitiveness of electrolytic Zinc process by chemical reaction engineering approach

This doctoral thesis describes the development work performed on the leachand purification sections in the electrolytic zinc plant in Kokkola to increase the efficiency in these two stages, and thus the competitiveness of the plant. Since metallic zinc is a typical bulk product, the improvement of the competitiveness of a plant was mostly an issue of decreasing unit costs. The problems in the leaching were low recovery of valuable metals from raw materials, and that the available technology offered complicated and expensive processes to overcome this problem. In the purification, the main problem was consumption of zinc powder - up to four to six times the stoichiometric demand. This reduced the capacity of the plant as this zinc is re-circulated through the electrolysis, which is the absolute bottleneck in a zinc plant. Low selectivity gave low-grade and low-value precipitates for further processing to metallic copper, cadmium, cobalt and nickel. Knowledge of the underlying chemistry was poor and process interruptions causing losses of zinc production were frequent. Studies on leaching comprised the kinetics of ferrite leaching and jarosite precipitation, as well as the stability of jarosite in acidic plant solutions. A breakthrough came with the finding that jarosite could precipitate under conditions where ferrite would leach satisfactorily. Based on this discovery, a one-step process for the treatment of ferrite was developed. In the plant, the new process almost doubled the recovery of zinc from ferrite in the same equipment as the two-step jarosite process was operated in at that time. In a later expansion of the plant, investment savings were substantial compared to other technologies available. In the solution purification, the key finding was that Co, Ni, and Cu formed specific arsenides in the “hot arsenic zinc dust” step. This was utilized for the development of a three-step purification stage based on fluidized bed technology in all three steps, i.e. removal of Cu, Co and Cd. Both precipitation rates and selectivity increased, which strongly decreased the zinc powder consumption through a substantially suppressed hydrogen gas evolution. Better selectivity improved the value of the precipitates: cadmium, which caused environmental problems in the copper smelter, was reduced from 1-3% reported normally down to 0.05 %, and a cobalt cake with 15 % Co was easily produced in laboratory experiments in the cobalt removal. The zinc powder consumption in the plant for a solution containing Cu, Co, Ni and Cd (1000, 25, 30 and 350 mg/l, respectively), was around 1.8 g/l; i.e. only 1.4 times the stoichiometric demand – or, about 60% saving in powder consumption. Two processes for direct leaching of the concentrate under atmospheric conditions were developed, one of which was implemented in the Kokkola zinc plant. Compared to the existing pressure leach technology, savings were obtained mostly in investment. The scientific basis for the most important processes and process improvements is given in the doctoral thesis. This includes mathematical modeling and thermodynamic evaluation of experimental results and hypotheses developed. Five of the processes developed in this research and development program were implemented in the plant and are still operated. Even though these processes were developed with the focus on the plant in Kokkola, they can also be implemented at low cost in most of the zinc plants globally, and have thus a great significance in the development of the electrolytic zinc process in general.

Reframing the relationship between service design and operations: a service engineering approach

The significance of services as business and human activities has increased dramatically throughout the world in the last three decades. Becoming a more and more competitive and efficient service provider while still being able to provide unique value opportunities for customers requires new knowledge and ideas. Part of this knowledge is created and utilized in daily activities in every service organization, but not all of it, and therefore an emerging phenomenon in the service context is information awareness. Terms like big data and Internet of things are not only modern buzz-words but they are also describing urgent requirements for a new type of competences and solutions. When the amount of information increases and the systems processing information become more efficient and intelligent, it is the human understanding and objectives that may get separated from the automated processes and technological innovations. This is an important challenge and the core driver for this dissertation: What kind of information is created, possessed and utilized in the service context, and even more importantly, what information exists but is not acknowledged or used? In this dissertation the focus is on the relationship between service design and service operations. Reframing this relationship refers to viewing the service system from the architectural perspective. The selected perspective allows analysing the relationship between design activities and operational activities as an information system while maintaining the tight connection to existing service research contributions and approaches. This type of an innovative approach is supported by research methodology that relies on design science theory. The methodological process supports the construction of a new design artifact based on existing theoretical knowledge, creation of new innovations and testing the design artifact components in real service contexts. The relationship between design and operations is analysed in the health care and social care service systems. The existing contributions in service research tend to abstract services and service systems as value creation, working or interactive systems. This dissertation adds an important information processing system perspective to the research. The main contribution focuses on the following argument: Only part of the service information system is automated and computerized, whereas a significant part of information processing is embedded in human activities, communication and ad-hoc reactions. The results indicate that the relationship between service design and service operations is more complex and dynamic than the existing scientific and managerial models tend to view it. Both activities create, utilize, mix and share information, making service information management a necessary but relatively unknown managerial task. On the architectural level, service system -specific elements seem to disappear, but access to more general information elements and processes can be found. While this dissertation focuses on conceptual-level design artifact construction, the results provide also very practical implications for service providers. Personal, visual and hidden activities of service, and more importantly all changes that take place in any service system have also an information dimension. Making this information dimension visual and prioritizing the processed information based on service dimensions is likely to provide new opportunities to increase activities and provide a new type of service potential for customers.

Value engineering of InnoTrackTM

Middle section module of InnoTrackTM moving walk was re-engineered according to value analysis process. Self-supporting steel structure for moving walk was created as a result of this process. Designed structure was verified and validated by prototype tests and finite element method calculations. Self-supporting steel structure replaces the original design of middle section module in InnoTrackTM. Designed structure provides higher satisfaction to customers’ needs and at the same time, it uses less resources. The redesigned middle section module provides higher value to the customer.

Sustainable Gold Mining- Life Cycle Assessment of Cyanidation and Thiosulphate Leaching

With the increasing concern of the sustainable approach of gold mining, thiosulphate has been researched as an alternative lixiviant to cyanide since cyanide is toxic to the environment. In order to investigate the possibility of thiosulphate leaching application in the coming future, life cycle assessment, is conducted to compare the environmental footprint of cyanidation and thiosulphate leaching. The result showed the most significant environmental impact of cyanidation is toxicity to human, while the ammonia of thiosulphate leaching is also a major concern of acidification. In addition, an ecosystem evaluation is also performed to indicate the potential damages caused by an example of cyanide spill at Kittilä mine, resulting in significant environmental risk cost that has to be taken into account for decision making. From the opinion collected from an online LinkedIn discussion forum, the anxiety of sustainability alone would not be enough to contribute a significant change of conventional cyanidation, until the tighten policy of cyanide use. International Cyanide Code, therefore, is crucial for safe gold production. Nevertheless, it is still thoughtful to consider the values of healthy ecosystem and the gold for long-term benefit.

A Phase Model for Building a Customer Value Based Sales Tool – Case Mining and Metals Industry

The objective of this research is to observe the state of customer value management in Outotec Oyj, determine the key development areas and develop a phase model with which to guide the development of a customer value based sales tool. The study was conducted with a constructive research approach with the focus of identifying a problem and developing a solution for the problem. As a basis for the study, the current literature involving customer value assessment and solution and customer value selling was studied. The data was collected by conducting 16 interviews in two rounds within the company and it was analyzed by coding openly. First, seven important development areas were identified, out of which the most critical were “Customer value mindset inside the company” and “Coordination of customer value management activities”. Utilizing these seven areas three functionality requirements, “Preparation”, “Outotec’s value creation and communication” and “Documentation” and three development requirements for a customer value sales tool were identified. The study concluded with the formulation of a phase model for building a customer value based sales tool. The model included five steps that were defined as 1) Enable customer value utilization, 2) Connect with the customer, 3) Create customer value, 4) Define tool to facilitate value selling and 5) Develop sales tool. Further practical activities were also recommended as a guide for executing the phase model.

The demand-supply balancing process in supply chain management - case mining & metals industry equipment

The aim of this thesis is to search how to match the demand and supply effectively in industrial and project-oriented business environment. The demand-supply balancing process is searched through three different phases: the demand planning and forecasting, synchronization of demand and supply and measurement of the results. The thesis contains a single case study that has been implemented in a company called Outotec. In the case study the demand is planned and forecasted with qualitative (judgmental) forecasting method. The quantitative forecasting methods are searched further to support the demand forecast and long term planning. The sales and operations planning process is used in the synchronization of the demand and supply. The demand forecast is applied in the management of a supply chain of critical unit of elemental analyzer. Different meters on operational and strategic level are proposed for the measurement of performance.

Digitaalisen valmistuksen vaikutus hitsatun rakenteen väsymiskestävyyteen

Tässä työssä tutkittiin kuinka eri tavoin rakenteen mallintaminen vaikuttaa laskettuun väsy-misikään. Työssä tutkittavana rakenteena toimi Sandvik Mining and Construction OY:n las-tauskoneen nostovarsi. Nostovarrelle väsytyskokeet suoritettiin Lappeenrannan teknillisen yliopiston teräsrakenteiden laboratoriossa. Työn tavoitteena oli tutkia miten eri digitaalinen valmistuksen tasot vaikuttavat hitsatulle rakenteelle saatuun kestoikään. Työssä tutkittiin myös miten todellista geometriaa voidaan hyödyntää rakenteen kestoiän arvioinnissa. Väsytyskoejärjestely mallinnettiin FE-menetelmällä, ja järjestelystä tehtiin useita malleja käyttäen solidi- ja laattaelementtejä. Malleista laskettiin väsymisiät hot spot- ja tehollisen lovijännityksen menetelmällä, ja saatuja tuloksia vertailtiin toisiinsa ja väsytyskokeen tulok-siin. Väsytyskokeessa vaurioituneista kohdista tarkemman tutkimuksen kohteena oli nosto-varren palstalevyn kärki. Hot spot-menetelmällä saadut kestoiät vaihtelivat paikoin melko paljon eri mallien välillä. Tehollisen lovijännityksen menetelmällä saaduissa tuloksissa erot olivat pienempiä mallien välillä. FE-mallin ja venymäliuskojen jännitykset poikkesivat toisistaan paikoin melko pal-jon. Todellisen hitsatun rakenteen kestoikään vaikuttaa moni asia, ja täten FE-menetelmällä las-kettu kestoikä voi poiketa huomattavasti todellisesta kestoiästä. Varsinkin hot spot-menetel-mällä tulokset voivat poiketa hyvinkin paljon todellisuudesta, mikäli jännitystila tutkitta-vassa kohdassa on moniaksiaalinen. Todellisen geometrian mallintaminen vaatii tarkkuutta, ja alkuperäisdatan tulee olla mahdollisimman tarkkaa ja riittävän suurelta alueelta, jotta malli vastaa tarpeeksi todellista.

Customer´s perceptions of value during the lifecycle of concentrate filtration

The objective of this study was to examine how customers purchase complex industrial solutions in mining industry, and what kind of value they perceive during different phases of the solution life cycle. In addition, a systematic method for understanding customer value was developed, which can be applied for other company’s offerings as well. The method includes step-by-step instructions for 1) the collection of customer value data and 2) implementation of the findings. The theoretical part of the study focuses on solution and customer value literature in business-to-business markets. In this study qualitative embedded multiple-case study was used as a research method. The primary data was collected through in-depth interviews in two market areas and by participating in customer meetings as an external observer. The results show that there are two ways of buying solutions that needs to be treated individually. Customers prefer to buy solutions from engineering companies as they think that suppliers still need to work on their solution capabilities. Therefore, Outotec should focus more on marketing itself as a solution provider. Customers buy solutions that create the most value with the lowest risk and they need to be supported throughout the solution lifecycle. References that demonstrate previous experience are the most effective way to reduce customers’ risk. However, the customer-perceived values and challenges differ between the market areas, and thus, suppliers should have divergent strategies for specific market areas.

Advanced biofuel production: Engineering metabolic pathways for butanol and propane biosynthesis.

Greenhouse gases emitted from energy production and transportation are dramatically changing the climate of Planet Earth. As a consequence, global warming is affecting the living conditions of numerous plant and animal species, including ours. Thus the development of sustainable and renewable liquid fuels is an essential global challenge in order to combat the climate change. In the past decades many technologies have been developed as alternatives to currently used petroleum fuels, such as bioethanol and biodiesel. However, even with gradually increasing production, the market penetration of these first generation biofuels is still relatively small compared to fossil fuels. Researchers have long ago realized that there is a need for advanced biofuels with improved physical and chemical properties compared to bioethanol and with biomass raw materials not competing with food production. Several target molecules have been identified as potential fuel candidates, such as alkanes, fatty acids, long carbon‐chain alcohols and isoprenoids. The current study focuses on the biosynthesis of butanol and propane as possible biofuels. The scope of this research was to investigate novel heterologous metabolic pathways and to identify bottlenecks for alcohol and alkane generation using Escherichia coli as a model host microorganism. The first theme of the work studied the pathways generating butyraldehyde, the common denominator for butanol and propane biosynthesis. Two ways of generating butyraldehyde were described, one via the bacterial fatty acid elongation machinery and the other via partial overexpression of the acetone‐butanol‐ethanol fermentation pathway found in Clostridium acetobutylicum. The second theme of the experimental work studied the reduction of butyraldehyde to butanol catalysed by various bacterial aldehyde‐reductase enzymes, whereas the final part of the work investigated the in vivo kinetics of the cyanobacterial aldehyde deformylating oxygenase (ADO) for the generation of hydrocarbons. The results showed that the novel butanol pathway, based on fatty acid biosynthesis consisting of an acyl‐ACP thioesterase and a carboxylic acid reductase, is tolerant to oxygen, thus being an efficient alternative to the previous Clostridial pathways. It was also shown that butanol can be produced from acetyl‐CoA using acetoacetyl CoA synthase (NphT7) or acetyl‐CoA acetyltransferase (AtoB) enzymes. The study also demonstrated, for the first time, that bacterial biosynthesis of propane is possible. The efficiency of the system is clearly limited by the poor kinetic properties of the ADO enzyme, and for proper function in vivo, the catalytic machinery requires a coupled electron relay system.

Enhancing business-to-business relationship through value co-creation in traditional business sector: A case of building services engineering

This study discusses the significance of having service as a business logic, and more specifically, how value co-creation can be seen as an enhancing phenomenon to business-to-business relationships in traditional business sector. The purpose of this study is to investigate how value cocreation can enhance a business-to-business relationship in the heating, ventilation and airconditioning (HVAC) industry of building services engineering, through three sub-objectives: to identify what is value in the industry, how value is co-created in the industry, and what is value in a business-to-business relationship in the industry. The theoretical part this study consists of academic knowledge and literature related to the concepts of value, value co-creation and business-to-business relationships. In order to research value co-creation and business-to-business relationships in HVAC industry of building services engineering both, metaphorical and conceptual thinking of service dominant (S-D) logic and more managerial approach of service logic (SL), contributed to the theoretical part of the study. The empirical research conducted for this study is based on seven semi-structured interviews, which constituted the holistic, qualitative single case study method chosen for the research. The data was collected in September 2014 from CEOs, managers and owners representing six building services engineering firms. The interviews were analysed with the help of transcriptions, role-ordered matrices and thematic networks. The findings of this study indicate that value in HVAC industry consists of client expertise and supplier expertise. The result of applying client expertise and supplier expertise to the business-to- business relationship is characterized as value-in-reputation, when continuity, interaction, learning and rapport of the business relationship are ensured. As a result, value co-creation in the industry consists of mutual and separate elements, which the client and the supplier apply in the process, in addition to proactive interaction. The findings of this study, together with the final framework, enhance the understanding of the connection existing between value co-creation and business-to-business relationship. The findings suggest that value in the HVAC industry is characterized by both value-in-use and value-inreputation. Value-in-reputation enhances the formation of value-in-use, and consequently, value cocreation enhances the business-to-business relationship. This study thus contributes to the existing knowledge on the concepts of value and value co-creation in business-to-business relationships.

Determinants of capital expenditures: Evidence from oil and mining sectors in Russia

This master’s thesis investigates the significant macroeconomic and firm level determinants of CAPEX in Russian oil and mining sectors. It also studies the Russian oil and mining sectors, its development, characteristics and current situation. The panel data methodology was implemented to identify the determinants of CAPEX in Russian oil and mining sectors and to test derived hypotheses. The core sample consists of annual financial data of 45 publicly listed Russian oil and mining sector companies. The timeframe of the thesis research is a six year period from 2007 to 2013. The findings of the master’s thesis have shown that Gross Sales, Return On Assets, Free Cash Flow and Long Term Debt are firm level performance variables along with Russian GDP, Export, Urals and the Reserve Fund are macroeconomic variables that determine the magnitude of new capital expenditures reported by publicly listed Russian oil and mining sector companies. These results are not controversial to the previous research paper, indeed they confirm them. Furthermore, the findings from the emerging countries, such as Malaysia, India and Portugal, are analogous to Russia. The empirical research is edifying and novel. Findings from this master’s thesis are highly valuable for the scientific community, especially, for researchers who investigate the determinant of CAPEX in developing countries. Moreover, the results can be utilized as a cogent argument, when companies and investors are doing strategic decisions, considering the Russian oil and mining sectors.