Heat transfer inside internal combustion engine: modelling and comparison with experimental data

The paper is devoted to study specific aspects of heat transfer in the combustion chamber of compression ignited reciprocating internal combustion engines and possibility to directly measure the heat flux by means of Gradient Heat Flux Sensors (GHFS). A one – dimensional single zone model proposed by Kyung Tae Yun et al. and implemented with the aid of Matlab, was used to obtain approximate picture of heat flux behavior in the combustion chamber with relation to the crank angle. The model’s numerical output was compared to the experimental results. The experiment was accomplished by A. Mityakov at four stroke diesel engine Indenor XL4D. Local heat fluxes on the surface of cylinder head were measured with fast – response, high – sensitive GHFS. The comparison of numerical data with experimental results has revealed a small deviation in obtained heat flux values throughout the cycle and different behavior of heat flux curve after Top Dead Center.

Heat flux measurement inside internal combustion engine with gradient heat flux sensor.

This master’s thesis is devoted to study different heat flux measurement techniques such as differential temperature sensors, semi-infinite surface temperature methods, calorimetric sensors and gradient heat flux sensors. The possibility to use Gradient Heat Flux Sensors (GHFS) to measure heat flux in the combustion chamber of compression ignited reciprocating internal combustion engines was considered in more detail. A. Mityakov conducted an experiment, where Gradient Heat Flux Sensor was placed in four stroke diesel engine Indenor XL4D to measure heat flux in the combustion chamber. The results which were obtained from the experiment were compared with model’s numerical output. This model (a one – dimensional single zone model) was implemented with help of MathCAD and the result of this implementation is graph of heat flux in combustion chamber in relation to the crank angle. The values of heat flux throughout the cycle obtained with aid of heat flux sensor and theoretically were sufficiently similar, but not identical. Such deviation is rather common for this type of experiment.

Ympäristöjärjestelmän rakentaminen ja sen haasteet Lappeenrannan teknillisellä yliopistolla

Lappeenrannan teknilliselle yliopistolle on rakennettu ISO14001-mukaista ympäristöjärjestelmää. Tässä diplomityössä tarkastellaan rakentamisen vaiheita sekä etsitään ratkaisuja rakentamisen aikana ilmeneviin haasteisiin. Teoriaosassa keskitytään ympäristö- ja kestävän kehityksen toimintaan yliopistoissa sekä ISO14001-standardin mukaisiin ympäristöjärjestelmiin. Ympäristöjärjestelmää rakennettaessa luodaan ympäristöpolitiikka sekä arvioidaan ja valitaan yliopiston merkittävimmät ympäristönäkökohdat. Näkökohdille luodaan päämäärät, tavoitteet ja ohjelmat. Lisäksi työssä tarkastellaan lakisääteisiä vaatimuksia ja luodaan menetelmiä dokumentointiin, koulutukseen, poikkeamien havainnointiin ja sisäiseen auditointiin. Yliopistolle on mahdollista rakentaa toimiva ympäristöjärjestelmä, mutta se vaatii aika- ja taloudellisten resurssien lisäksi myös vahvan tuen ylimmältä johdolta sekä halua ajaa muutos organisaatioon.

Improving internal performance of a company - Introducing employee empowerment via job redesign in Finnish small and medium sized enterprises

This bachelor's thesis is about to find out to what extent Finnish managers and small and medium sized organizations are willing and able to put employee empowerment into practice and what experiences they have got from employee empowerment as an approach towards job redesign. Some of the top enterprises in the world are known for their empowered employees as a single most important factor for their success and this thesis focuses on introducing the subject to Finnish managers and organizations to find out what benefits, barriers and other thoughts they have about the whole idea of empowered employees in Finnish organization culture. Most notable findings in this thesis are that Finnish managers do think that their organization's employees are capable to work efficiently if their job is extended and the organizations would perform better when right person's job is enriched and he/she is given more power to solve problems.

Ingest into the Digital Preservation Network: Standard Pipelines

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

The ETH Zurich DOI Desk: DOIs as standard persistent identifier and best practice in Swiss Open Access repositories

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Successful IFRS standard change implementation process after the initial IFRS implementation

The main objective of the study was to form a strategic process model and project management tool to help IFRS change implementation projects in the future. These research results were designed based on the theoretical framework of Total Quality Management and leaning on the facts that were collected during the empirical case study of IAS 17 change. The us-age of the process oriented approach in IFRS standard change implementation after the initial IFRS implementation is rationalized with the following arguments: 1) well designed process tools lead to optimization of resources 2) With the help of process stages and related tasks it is easy to ensure the efficient way of working and managing the project as well as make sure to include all necessary stakeholders to the change process. This research is following the qualitative approach and the analysis is in describing format. The first part of the study is a literature review and the latter part has been conducted as a case study. The data has been col-lected in the case company with interviews and observation. The main findings are a process model for IFRS standard change process and a check-list formatted management tool for up-coming IFRS standard change projects. The process flow follows the main cornerstones in IASB’s standard setting process and the management tool has been divided to stages accordingly.

Analyzing the Effects of the New Renewable Energy Policy in Russia on Investments into Wind, Solar and Small Hydro Power

This thesis presents an analysis of recently enacted Russian renewable energy policy based on capacity mechanism. Considering its novelty and poor coverage by academic literature, the aim of the thesis is to analyze capacity mechanism influence on investors’ decision-making process. The current research introduces a number of approaches to investment analysis. Firstly, classical financial model was built with Microsoft Excel® and crisp efficiency indicators such as net present value were determined. Secondly, sensitivity analysis was performed to understand different factors influence on project profitability. Thirdly, Datar-Mathews method was applied that by means of Monte Carlo simulation realized with Matlab Simulink®, disclosed all possible outcomes of investment project and enabled real option thinking. Fourthly, previous analysis was duplicated by fuzzy pay-off method with Microsoft Excel®. Finally, decision-making process under capacity mechanism was illustrated with decision tree. Capacity remuneration paid within 15 years is calculated individually for each RE project as variable annuity that guarantees a particular return on investment adjusted on changes in national interest rates. Analysis results indicate that capacity mechanism creates a real option to invest in renewable energy project by ensuring project profitability regardless of market conditions if project-internal factors are managed properly. The latter includes keeping capital expenditures within set limits, production performance higher than 75% of target indicators, and fulfilling localization requirement, implying producing equipment and services within the country. Occurrence of real option shapes decision-making process in the following way. Initially, investor should define appropriate location for a planned power plant where high production performance can be achieved, and lock in this location in case of competition. After, investor should wait until capital cost limit and localization requirement can be met, after that decision to invest can be made without any risk to project profitability. With respect to technology kind, investment into solar PV power plant is more attractive than into wind or small hydro power, since it has higher weighted net present value and lower standard deviation. However, it does not change decision-making strategy that remains the same for each technology type. Fuzzy pay-method proved its ability to disclose the same patterns of information as Monte Carlo simulation. Being effective in investment analysis under uncertainty and easy in use, it can be recommended as sufficient analytical tool to investors and researchers. Apart from described results, this thesis contributes to the academic literature by detailed description of capacity price calculation for renewable energy that was not available in English before. With respect to methodology novelty, such advanced approaches as Datar-Mathews method and fuzzy pay-off method are applied on the top of investment profitability model that incorporates capacity remuneration calculation as well. Comparison of effects of two different RE supporting schemes, namely Russian capacity mechanism and feed-in premium, contributes to policy comparative studies and exhibits useful inferences for researchers and policymakers. Limitations of this research are simplification of assumptions to country-average level that restricts our ability to analyze renewable energy investment region wise and existing limitation of the studying policy to the wholesale power market that leaves retail markets and remote areas without our attention, taking away medium and small investment into renewable energy from the research focus. Elimination of these limitations would allow creating the full picture of Russian renewable energy investment profile.

Distortion and internal warping torsion of a double symmetric hollow section

This thesis is made in cooperation with Laboratory of Steel Structures and the steel company SSAB. Maximization of the benefits of high-strength steel usually requires the usage of thin wall thicknesses. This means the failures related to buckling, distortion and warping stand out. One must be aware of these phenomena to design thin-walled structures stressed with forces such as torsional loading. It is also important to take into account small stress ranges when evaluating the accurate fatigue strength of structures. The objective of this thesis is to clarify the theory of the uniform and non-uniform torsion. This paper focuses on warping due to the non-uniform torsion in double symmetric box girder and structural hollow section. The arisen stress states are explained and researched using the finite element method. Another research target is the distortion in double symmetric box girder due to torsion, and the restraining effect of transverse diaphragms at the load end. Multiple transverse diaphragms are used to study more efficient restraining against warping and distortion than a common one end plate structure.

Metal additive manufacturing of internal flow channels with powder bed fusion processes

This thesis studies the advantages, disadvantages and possibilities of additive manufacturing in making components with internal flow channels. These include hydraulic components, components with cooling channels and heat exchangers. Processes studied in this work are selective laser sintering and selective laser melting of metallic materials. The basic principles of processes and parameters involved in the process are presented and different possibilities of internal channel manufacturing and flow improvement are introduced

Improving reporting and internal control with process thinking - case study in a multinational corporation

The aim of this Master’s Thesis is to find applicable methods from process management literature for improving reporting and internal control in a multinational corporation. The method of analysis is qualitative and the research is conducted as a case study. Empirical data collection is carried out through interviews and participating observation. The theoretical framework is built around reporting and guidance between parent company and subsidiary, searching for means to improve them from process thinking and applicable frameworks. In the thesis, the process of intercompany reporting in the case company is modelled, and its weak points, risks, and development targets are identified. The framework of critical success factors in process improvement is utilized in assessing the development targets. Also internal control is analyzed with the tools of process thinking. As a result of this thesis, suggestions for actions improving the reporting process and internal control are made to the case company, the most essential of which are ensuring top management’s awareness and commitment to improvement, creating guidelines and tools for internal control and creating and implementing improved intercompany reporting process.

Spectrally Tuned Lanthanide Photoluminescence for Point-of-Care Testing

Point-of-care (POC) –diagnostics is a field with rapidly growing market share. As these applications become more widely used, there is an increasing pressure to improve their performance to match the one of a central laboratory tests. Lanthanide luminescence has been widely utilized in diagnostics because of the numerous advantages gained by the utilization of time-resolved or anti-Stokes detection. So far the use of lanthanide labels in POC has been scarce due to limitations set by the instrumentation required for their detection and the shortcomings, e.g. low brightness, of these labels. Along with the advances in the research of lanthanide luminescence, and in the field of semiconductors, these materials are becoming a feasible alternative for the signal generation also in the future POC assays. The aim of this thesis was to explore ways of utilizing time-resolved detection or anti-Stokes detection in POC applications. The long-lived fluorescence for the time-resolved measurement can be produced with lanthanide chelates. The ultraviolet (UV) excitation required by these chelates is cumbersome to produce with POC compatible fluorescence readers. In this thesis the use of a novel light-harvesting ligand was studied. This molecule can be used to excite Eu(III)-ions at wavelengths extending up to visible part of the spectrum. An enhancement solution based on this ligand showed a good performance in a proof-of-concept -bioaffinity assay and produced a bright signal upon 365 nm excitation thanks to the high molar absorptivity of the chelate. These features are crucial when developing miniaturized readers for the time-resolved detection of fluorescence. Upconverting phosphors (UCPs) were studied as an internal light source in glucose-sensing dry chemistry test strips and ways of utilizing their various emission wavelengths and near-infrared excitation were explored. The use of nanosized NaYF :Yb3+,Tm3+-particles enabled the replacement of an external UV-light source with a NIR-laser and gave an additional degree of freedom in the optical setup of the detector instrument. The new method enabled a blood glucose measurement with results comparable to a current standard method of measuring reflectance. Microsized visible emitting UCPs were used in a similar manner, but with a broad absorbing indicator compound filtering the excitation and emission wavelengths of the UCP. This approach resulted in a novel way of benefitting from the non-linear relationship between the excitation power and emission intensity of the UCPs, and enabled the amplification of the signal response from the indicator dye.