Development of fibre recovery process

The fiber recovery process is an essential part of the modern paper mill. It creates the basisfor mill's internal recirculation of the most important raw materials ¿ water and fiber. It is normally also a start point for further treatment of wastewater and if it works efficiently, it offers excellent basis to minimize effluents. This dissertation offers two different approaches to the subject. Firstly a novel save-all disc filter feeding system is developed and presented. This so-called precoat method is tested both in the laboratory and full-scale conditions. In laboratory scale it beats the traditional one clearly, when low freeness pulps are used as a sweetener stock. The full-scale application needs still some development work before it can be implemented to the paper mills. Secondly, the operationenvironment of save-all disc filter is studied mostly in laboratory conditions.The focus of this study is in cases, where low-freeness pulps are used as a sweetener stock of save-all filter. The effects of CSF-value, pressure drop, suspension consistency and retention chemicals to the quantity and quality of the filtrate was studied. Also the filtration resistance of the low freeness pulps was one studied.

Wet Oxidation of Concentrated Wastewaters: Process Combination and Reaction Kinetic Modeling

The accumulation of aqueous pollutants is becoming a global problem. The search for suitable methods and/or combinations of water treatment processes is a task that can slow down and stop the process of water pollution. In this work, the method of wet oxidation was considered as an appropriate technique for the elimination of the impurities present in paper mill process waters. It has been shown that, when combined with traditional wastewater treatment processes, wet oxidation offers many advantages. The combination of coagulation and wet oxidation offers a new opportunity for the improvement of the quality of wastewater designated for discharge or recycling. First of all, the utilization of coagulated sludge via wet oxidation provides a conditioning process for the sludge, i.e. dewatering, which is rather difficult to carry out with untreated waste. Secondly, Fe2(SO4)3, which is employed earlier as a coagulant, transforms the conventional wet oxidation process into a catalytic one. The use of coagulation as the post-treatment for wet oxidation can offer the possibility of the brown hue that usually accompanies the partial oxidation to be reduced. As a result, the supernatant is less colored and also contains a rather low amount of Fe ions to beconsidered for recycling inside mills. The thickened part that consists of metal ions is then recycled back to the wet oxidation system. It was also observed that wet oxidation is favorable for the degradation of pitch substances (LWEs) and lignin that are present in the process waters of paper mills. Rather low operating temperatures are needed for wet oxidation in order to destruct LWEs. The oxidation in the alkaline media provides not only the faster elimination of pitch and lignin but also significantly improves the biodegradable characteristics of wastewater that contains lignin and pitch substances. During the course of the kinetic studies, a model, which can predict the enhancements of the biodegradability of wastewater, was elaborated. The model includes lumped concentrations suchas the chemical oxygen demand and biochemical oxygen demand and reflects a generalized reaction network of oxidative transformations. Later developments incorporated a new lump, the immediately available biochemical oxygen demand, which increased the fidelity of the predictions made by the model. Since changes in biodegradability occur simultaneously with the destruction of LWEs, an attempt was made to combine these two facts for modeling purposes.

Validation Studies of Thermal-hydraulic Code for Safety Analysis of Nuclear Power Plants

This thesis gives an overview of the validation process for thermal hydraulic system codes and it presents in more detail the assessment and validation of the French code CATHARE for VVER calculations. Three assessment cases are presented: loop seal clearing, core reflooding and flow in a horizontal steam generator. The experience gained during these assessment and validation calculations has been used to analyze the behavior of the horizontal steam generator and the natural circulation in the geometry of the Loviisa nuclear power plant. The cases presented are not exhaustive, but they give a good overview of the work performed by the personnel of Lappeenranta University of Technology (LUT). Large part of the work has been performed in co-operation with the CATHARE-team in Grenoble, France. The design of a Russian type pressurized water reactor, VVER, differs from that of a Western-type PWR. Most of thermal-hydraulic system codes are validated only for the Western-type PWRs. Thus, the codes should be assessed and validated also for VVER design in order to establish any weaknesses in the models. This information is needed before codes can be used for the safety analysis. Theresults of the assessment and validation calculations presented here show that the CATHARE code can be used also for the thermal-hydraulic safety studies for VVER type plants. However, some areas have been indicated which need to be reassessed after further experimental data become available. These areas are mostly connected to the horizontal stem generators, like condensation and phase separation in primary side tubes. The work presented in this thesis covers a large numberof the phenomena included in the CSNI code validation matrices for small and intermediate leaks and for transients. Also some of the phenomena included in the matrix for large break LOCAs are covered. The matrices for code validation for VVER applications should be used when future experimental programs are planned for code validation.

Supporting knowledge creation and sharing in the early phases of the strategic innovation process

The driving forces of technology and globalization continuously transform the business landscape in a way which undermines the existing strategies and innovations of organizations. The challenge for organizations is to establish such conditions where they are able to create new knowledge for innovative business ideas in interaction between other organizations and individuals. Innovation processes continuously need new external stimulations and seek new ideas, new information and knowledge locating more and more outside traditional organizational boundaries. In several studies, the early phases of the innovation process have been considered as the most critical ones. During these phases, the innovation process can emerge or conclude. External knowledge acquirement and utilization are noticed to be important at this stage of the innovation process giving information about the development of future markets and needs for new innovative businessideas. To make it possible, new methods and approaches to manage proactive knowledge creation and sharing activities are needed. In this study, knowledge creation and sharing in the early phases of the innovation process has been studied, and the understanding of knowledge management in the innovation process in an open and collaborative context advanced. Furthermore, the innovation management methods in this study are combined in a novel way to establish an open innovation process and tested in real-life cases. For these purposes two complementary and sequentially applied group work methods - the heuristic scenario method and the idea generation process - are examined by focusing the research on the support of the open knowledge creation and sharing process. The research objective of this thesis concerns two doctrines: the innovation management including the knowledge management, and the futures research concerning the scenario paradigm. This thesis also applies the group decision support system (GDSS) in the idea generation process to utilize the converged knowledge during the scenario process.

Mobile Communications within the European Union: The Role of Location in the Evolution and Forecasting of the Diffusion Process

In the European Union, the importance of mobile communications was realized early on. The process of mobile communications becoming ubiquitous has taken time, as the innovation of mobile communications diffused into the society. The aim of this study is to find out how the evolution and spatial patterns of the diffusion of mobile communications within the European Union could be taken into account in forecasting the diffusion process. There is relatively lot of research of innovation diffusion on the individual (micro) andthe country (macro) level, if compared to the territorial level. Territorial orspatial diffusion refers either to the intra-country or inter-country diffusionof an innovation. In both settings, the dif- fusion of a technological innovation has gained scarce attention. This study adds knowledge of the diffusion between countries, focusing especially on the role of location in this process. The main findings of the study are the following: The penetration rates of the European Union member countries have become more even in the period of observation, from the year 1981 to 2000. The common digital GSM system seems to have hastened this process. As to the role of location in the diffusion process, neighboring countries have had similar diffusion processes. They can be grouped into three, the Nordic countries, the central and southern European countries, and the remote southern European countries. The neighborhood effect is also domi- nating in thegravity model which is used for modeling the adoption timing of the countries. The subsequent diffusion within a country, measured by the logistic model in Finland, is af- fected positively by its economic situation, and it seems to level off at some 92 %. Considering the launch of future mobile communications systemsusing a common standard should implicate an equal development between the countries. The launching time should be carefully selected as the diffusion is probably delayed in economic downturns. The location of a country, measured by distance, can be used in forecasting the adoption and diffusion. Fi- nally, the result of penetration rates becoming more even implies that in a relatively homoge- nous set of countries, such as the European Union member countries, the estimated final pene- tration of a single country can be used for approximating the penetration of the others. The estimated eventual penetration of Finland, some 92 %, should thus also be the eventual level for all the European Union countries and for the European Union as a whole.

Welding time models for cost calculations in the early stages of the design process

It is generally accepted that between 70 and 80% of manufacturing costs can be attributed to design. Nevertheless, it is difficult for the designer to estimate manufacturing costs accurately, especially when alternative constructions are compared at the conceptual design phase, because of the lack of cost information and appropriate tools. In general, previous reports concerning optimisation of a welded structure have used the mass of the product as the basis for the cost comparison. However, it can easily be shown using a simple example that the use of product mass as the sole manufacturing cost estimator is unsatisfactory. This study describes a method of formulating welding time models for cost calculation, and presents the results of the models for particular sections, based on typical costs in Finland. This was achieved by collecting information concerning welded products from different companies. The data included 71 different welded assemblies taken from the mechanical engineering and construction industries. The welded assemblies contained in total 1 589 welded parts, 4 257 separate welds, and a total welded length of 3 188 metres. The data were modelled for statistical calculations, and models of welding time were derived by using linear regression analysis. Themodels were tested by using appropriate statistical methods, and were found to be accurate. General welding time models have been developed, valid for welding in Finland, as well as specific, more accurate models for particular companies. The models are presented in such a form that they can be used easily by a designer, enabling the cost calculation to be automated.

Applying the principles of life cycle assessment and costing in process modeling to examine profit-making capability

Static process simulation has traditionally been used to model complex processes for various purposes. However, the use of static processsimulators for the preparation of holistic examinations aiming at improving profit-making capability requires a lot of work because the production of results requires the assessment of the applicability of detailed data which may be irrelevant to the objective. The relevant data for the total assessment gets buried byirrelevant data. Furthermore, the models do not include an examination of the maintenance or risk management, and economic examination is often an extra property added to them which can be performed with a spreadsheet program. A process model applicable to holistic economic examinations has been developed in this work. The model is based on the life cycle profit philosophy developed by Hagberg and Henriksson in 1996. The construction of the model has utilized life cycle assessment and life cycle costing methodologies with a view to developing, above all, a model which would be applicable to the economic examinations of complete wholes and which would require the need for information focusing on aspects essential to the objectives. Life cycle assessment and costing differ from each other in terms of the modeling principles, but the features of bothmethodologies can be used in the development of economic process modeling. Methods applicable to the modeling of complex processes can be examined from the viewpoint of life cycle methodologies, because they involve the collection and management of large corpuses of information and the production of information for the needs of decision-makers as well. The results of the study shows that on the basis of the principles of life cycle modeling, a process model can be created which may be used to produce holistic efficiency examinations on the profit-making capability of the production line, with fewer resources thanwith traditional methods. The calculations of the model are based to the maximum extent on the information system of the factory, which means that the accuracyof the results can be improved by developing information systems so that they can provide the best information for this kind of examinations.

Studies on coordination of systems development process

This thesis examines coordination of systems development process in a contemporary software producing organization. The thesis consists of a series of empirical studies in which the actions, conceptions and artifacts of practitioners are analyzed using a theory-building case study research approach. The three phases of the thesis provide empirical observations on different aspects of systemsdevelopment. In the first phase is examined the role of architecture in coordination and cost estimation in multi-site environment. The second phase involves two studies on the evolving requirement understanding process and how to measure this process. The third phase summarizes the first two phases and concentrates on the role of methods and how practitioners work with them. All the phases provide evidence that current systems development method approaches are too naïve in looking at the complexity of the real world. In practice, development is influenced by opportunity and other contingent factors. The systems development processis not coordinated using phases and tasks defined in methods providing universal mechanism for managing this process like most of the method approaches assume.Instead, the studies suggest that managing systems development process happens through coordinating development activities using methods as tools. These studies contribute to the systems development methods by emphasizing the support of communication and collaboration between systems development participants. Methods should not describe the development activities and phases in a detail level, butshould include the higher level guidance for practitioners on how to act in different systems development environments.

Ash Particle Erosion on Steam Boiler Convective Section

In this study, equations for the calculation of erosion wear caused by ash particles on convective heat exchanger tubes of steam boilers are presented. Anew, three-dimensional test arrangement was used in the testing of the erosion wear of convective heat exchanger tubes of steam boilers. When using the sleeve-method, three different tube materials and three tube constructions could be tested. New results were obtained from the analyses. The main mechanisms of erosionwear phenomena and erosion wear as a function of collision conditions and material properties have been studied. Properties of fossil fuels have also been presented. When burning solid fuels, such as pulverized coal and peat in steam boilers, most of the ash is entrained by the flue gas in the furnace. In bubbling andcirculating fluidized bed boilers, particle concentration in the flue gas is high because of bed material entrained in the flue gas. Hard particles, such as sharp edged quartz crystals, cause erosion wear when colliding on convective heat exchanger tubes and on the rear wall of the steam boiler. The most important ways to reduce erosion wear in steam boilers is to keep the velocity of the flue gas moderate and prevent channelling of the ash flow in a certain part of the cross section of the flue gas channel, especially near the back wall. One can do this by constructing the boiler with the following components. Screen plates can beused to make the velocity and ash flow distributions more even at the cross-section of the channel. Shield plates and plate type constructions in superheaters can also be used. Erosion testing was conducted with three types of tube constructions: a one tube row, an inline tube bank with six tube rows, and a staggered tube bank with six tube rows. Three flow velocities and two particle concentrations were used in the tests, which were carried out at room temperature. Three particle materials were used: quartz, coal ash and peat ash particles. Mass loss, diameter loss and wall thickness loss measurements of the test sleeves were taken. Erosion wear as a function of flow conditions, tube material and tube construction was analyzed by single-variable linear regression analysis. In developing the erosion wear calculation equations, multi-variable linear regression analysis was used. In the staggered tube bank, erosion wear had a maximum value in a tube row 2 and a local maximum in row 5. In rows 3, 4 and 6, the erosion rate was low. On the other hand, in the in-line tube bank the minimum erosion rate occurred in tube row 2 and in further rows the erosion had an increasing value, so that in a six row tube bank, the maximum value occurred in row 6.

Optimizing the Testing Process in Module Testing – Functional Testing Interface

Today's business environment has become increasingly unexpected and fast changing because of the global competition. This new environment requires the companies to organize their control differently, e.g. by logistic process thinking. Logistic process thinking in software engineering applies the principles of production process to immaterial products. Processes must be optimized, so that every phase adds value to the customer, and the lead times can be cut shorter to meet the new customer requirements. The purpose of this thesis is to examine and optimize the testing processes of software engineering concentrating on module testing, functional testing and their interface. The concept of logistic process thinking is introduced through production process, value added model and process management. Also theory of testing based on literature is presented, concentrating on module testing and functional testing. The testing processes of the Case Company are presented together with the project models in which they are implemented. The real life practices in module testing and functional testing and their interface are examined through interviews. These practices are analyzed against the processes and the testing theory, through which ideas for optimizing the testing process are introduced. The project world of the Case Company is also introduced together with two example testing projects in different life cycle phases. The examples give a view of how much effort of the project is put in different types of testing.

A Technology Intelligence Process for a High Technology Company

Tämä diplomityö määrittelee teknologiaseurantaprosessin, jolla korkean teknologian yritys voi ohjata toimintaansa. Korkean teknologian yrityksille on olennaista seurata teknologian kehitystä. Tällaiset yritykset tarvitsevat hyvin määritellyn järjestelmän, jolla ne voivat seurata ja ennustaa teknologista kehitystä.Työssä esitetään, että teknologiaseuranta ja kilpailuseuranta (competitive intelligence) ovat business intelligencen osa-alueita, jotka täydentävät ja tukevat toisiaan. Tärkeä havainto on, että business intelligence -prosessi on ennen kaikkea organisaation oppimisprosessi. Tästä seuraa, että minkä tahansa BI-prosessin tulisi perustua niihin prosesseihin, joiden avulla organisaatiot oppivat. Työssä esitetään myös, miten business intelligence, tietojohtaminen (knowledge management) ja organisaatioiden oppiminen liittyvät toisiinsa.Teknologiaseuranta on elintärkeä toiminto korkean teknologian yritykselle; sitä tarvitaan monella strategisen johtamisen osa-alueella, ainakin teknologia-, markkinointi- ja henkilöstöjohtamisessa. Teknologiaseurannan havaitaan myös olevan korkean teknologian yritykselle erittäin tärkeä ydinosaamisalue, jota ei voi kokonaan ulkoistaa.Työssä esitellään teknologiaseurantaprosessi, joka perustuu yleiselle business intelligence -prosessille ja siitä johdetulle kilpailuseurantaprosessille. Työssä myös esitetään ehdotus siitä, kuinka teknologiaseuranta voitaisiin järjestää korkean teknologian yrityksessä. Esitetty ratkaisu perustuu Community of practice -käsitteeseen. Community of practice on vapaaehtoisuuteen perustuva tiimi, jonka jäseniä yhdistää kiinnostus johonkin asiaan ja oppimishalu. Esimerkkiyrityksessä on tunnistettu selkeä tarve yhtenäiseen ja koordinoituun teknologiaseurantaan. Työssä esitetään alustava teknologiaseurantaprosessi esimerkkiyritykselle ja tunnistetaan teknologiaseurantaprosessin asiakkaat ja tekijät.

The Development of an Internal Testing Process for a Bluetooth Product

BlueGiga Technologies on uusi Bluetooth -teknologiaa soveltava pk-yritys. Yrityksen tuotekehitysprosessia täydentämään tarvittiin testausprosessi. Testausprosessin luominen oli haastavaa, koska Bluetooth -teknologia on uutta ja yritys on vielä nuori. Lisäksi se integroi kovo- ja ohjelmistokomponentteja tuotteissaan. Testaus aloitettiin evaluoimalla standardinmukaista tapaa dokumentoida testit. Tämän jälkeen tutkittiin BlueGigan ohjelmistokehitysprosessin suhdetta olemassa oleviin ohjelmistokehitysprosesseihin. Samanaikaisesti perehdyttiin Bluetooth -kvalifikaation testaukselle asettamiin vaatimuksiin. Tämän seurauksena TTCN:ää kokeiltiin helppolukuisen testitapauksen määrittelyssä. Käyttötapauksiin perustuvan testauksen sopivuutta Wireless Remote Access Platform:in (WRAP) testaamiseen arvioitiin kokeilemalla sitä Man-to-Machine -käyttötapauksen testaamisessa. Yllämainittujen tehtävien aikana kerätyn tiedon ja hankittujen kokemusten pohjalta laadittiin testausprosessi, joka kattaa yksikkö-, integraatio- ja järjestelmätason testauksen. Painopiste on järjestelmätason testauksessa. Prosessi määrittelee myös vastuuhenkilön tai -henkilöt eri testaustasoille.

Voimalaitoskytkennän lämpö-ja virtaustekninen optimointi teollisuusprosessiin

Diplomityössä on selvitetty UPM-Kymmene-konserniin kuuluvan Voikkaan paperitehtaan höyryvoimalaitoksen liityntärajapintaa paperikoneprosessiin. Selvitys tehtiin, koska nykyinen voimalaitos on suunniteltu korvattavaksi uudella lähivuosina. Työn teoriaosassa tarkastellaan mm. eri voimalaitostyyppejä, prosessivoimalaitoksen säätöjärjestelmiä sekä väliottovastapaineturbiinilta saatavan sähkötehon laskemiseksi tarvittavaa teoriaa. Käytännössä suurin työ on tehty nykyisen tuotantoprosessin voimalaitokselle asettamien vaatimusten selvittämisessä. Tämä on toteutettu tarkastelemalla online-mittauspositioita hyödyntäen laitoksen eri historiatietokantoja. Tulevan voimalaitoksen väliottovastapaineturbiinilta saatavaa sähkötehoa on tarkasteltu vuoden 2000 prosessihöyryn massavirtoihin perustuen. Kirjalliseen työhön on sisällytetty kuvaajat prosessin tärkeimmistä tila-arvoista. Yksityiskohtainen rajapinnan tarkastelu kuvaajineen ja lukuarvoineen on toimitettu diplomityöpaikalle tiedostomuodossa.

The Analysis of The Logistics Process between Finland and Russia in An EMS Company

Työn tavoitteena oli selventää Elcoteqin Suomen ja Venäjän välisten yksiköiden logistista prosessia ja erityisesti siihen liittyviä ongelmia. Työ on tehty Elcoteqin Engineering Services yksikköön, jossa ei tyypillisesti ole ollut asiaan liittyvää tietoa. Pääasiallisena työmenetelmänä olivat haastattelut sekä tutustuminen logistiseen putkeen käytännössä. Myös kirjallisuudella oli oma osansa, sekä tullaukseen että asiaan liittyvien teorioiden osalta. Teorioita ja käytännön kokemuksia yhdistäen edettiin analysointiin ja vertailuun, jonka perusteella annettiin suosituksia tulevia projekteja silmällä pitäen. Myös tulevaisuuden odotuksia on käsitelty yleisellä tasolla, lähinnä liittyen erilaisten kehitysohjelmien tarjoamiin mahdollisuuksiin. Logistiikka Suomen ja Venäjän välillä on huomattavasti monimutkaisempaa kuin ensisilmäyksellä näyttää. Ongelmia on niin rajanylityksen, tullauksen kuin lisenssiprosessinkin kanssa. Asioiden kehittämiseksi on kuitenkin paljon tehtävissä, kehityspotentiaali on valtava. Vahvaa panostusta liiketoiminnan kehittämiseksi Venäjällä on jatkettava, vaikka siihen liittyvät ongelmat välillä tuntuvatkin ylivoimaisen suurilta. Erityisen turhauttavia ovat asiat, joihin ei pystytä vaikuttamaan. Työn edetessä tuli kuitenkin esiin uusia näkökulmia, joita ei aiemmin ole otettu huomioon. Tuotteiden valintaan on jatkossa kiinnitettävä enemmän huomiota. Silti myös kuljetuksen ja rajanylityksen nopeuttamisen tutkimista on edelleen jatkettava.

SELLUTEHTAAN HÖYRYVERKON YLIJÄÄMÄENERGIAN HALLINNAN PARANTAMINEN

Tässä työssä on selvitetty sellutehtaan höyryverkosta tehtaan ulkopuolelle myytävän ylijäämähöyryn määrän ja paineen nopeaan vaihteluun vaikuttavia tekijöitä. Työssä on tarkasteltu höyryn kehityksen ja kulutuksen vaihtelun vaikutusta ylijäämähöyryyn. Lisäksi on tarkasteltu mahdollisuuksia edellä mainittujen häiriöiden tasaamiseksi. Työssä on selvitetty teoriaa, joka vaikuttaa sellutehtaan höyryn kehitykseen ja kulutukseen. Lisäksi on selvitetty energiataselaskennan ja höyryverkon hallintaa parantavien toimenpiteiden teoriaa. Omana kokonaisuutena on sellutehtaan höyryn kehityksen ja kulutuksen tarkastelu sekä selvitys tehtaan höyryverkon hallinnan nykytilasta. Höyryverkolle on muodostettu energiatase. Työn tuloksia varten on kerätty ja tallennettu mittapistetietoa tiedonkeräysjärjestelmän avulla eri höyryverkon mittapisteistä. Työn tuloksina on mainittu useita höyryverkon hallintaa parantavia toteutuskelpoisia asioita ja toimenpiteitä. Työllä on luotu pohjaa menetelmälle, joka ohjaa energian kehitystä vastaamaan sellun tuotannon tarvitsemaa energiamäärää. Samalla saataisiin paremmin hallittua ylijäämähöyryä ja sen määrän sekä paineen vaihtelu vähentyisi.