Unidirectional fiber-reinforced composite as an oral implant abutment material: Experimental studies of E-glass fiber/BisGMA-TEGDMA polymer in vitro

Fiber-reinforced composites (FRCs) are a new group of non-metallic biomaterials showing a growing popularity in many dental and medical applications. As an oral implant material, FRC is biocompatible in bone tissue environment. Soft tissue integration to FRC polymer material is unclear. This series of in vitro studies aimed at evaluating unidirectional E-glass FRC polymer in terms of mechanical, chemical, and biological properties in an attempt to develop a new non-metallic oral implant abutment alternative. Two different types of substrates were investigated: (a) Plain polymer (BisGMA 50%–TEGDMA 50%) and (b) Unidirectional FRC. The mechanical behavior of high fiber-density FRCs was assessed using a three-point bending test. Surface characterization was performed using scanning electron and spinning disk confocal microscopes. The surface wettability/energy was determined using sessile drop method. The blood response, including blood-clotting ability and platelet morphology was evaluated. Human gingival fibroblast cell responses - adhesion kinetics, adhesion strength, and proliferation activity - were studied in cell culture environment using routine test conditions. A novel tissue culture method was developed and used to evaluate porcine gingival tissue graft attachment and growth on the experimental composite implants. The analysis of the mechanical properties showed that there is a direct proportionality in the relationship between E-glass fiber volume fraction and toughness, modulus of elasticity, and load bearing capacity; however, flexural strength did not show significant improvement when high fiber-density FRC is used. FRCs showed moderate hydrophilic properties owing to the presence of exposed glass fibers on the polymer surface. Blood-clotting time was shorter on FRC substrates than on plain polymer. The FRC substrates also showed higher platelet activation state than plain polymer substrates. Fibroblast cell adhesion strength and proliferation rate were highly pronounced on FRCs. A tissue culture study revealed that gingival epithelium and connective tissue established an immediate close contact with both plain polymer and FRC implants. However, FRC seemed to guide epithelial migration outwards from the tissue/implant interface. Due to the anisotropic and hydrophilic nature of FRC, it can be concluded that this material enhances biological events related with soft tissue integration on oral implant surface.

Defining of the material models for stainless steels to be used in FE modeling

The aim of this work is to study the results of tensile tests for austenitic stainless steel type 304 and make accurate FE-models according to the results of the tests. Tensile tests were made at Central Research Institute of Structural Material, Prometey at Saint Petersburg and Mariyenburg in Russia. The test specimens for the tensile tests were produced at Lappeenranta University of Technology in a Laboratory of Steel Structures. In total 4 different tests were made, two with base material specimens and two with transverse butt weld specimens. Each kind of a specimen was tested at room temperature and at low temperature. By comparing the results of room and low temperature tests of similar test specimen we get to study the results of work hardening that affect the austenitic steels at below room temperature. The produced specimens are to be modeled accurately and then imported for nonlinear FEM- analyzing. Using the data gained from the tensile tests the aim is to get the models work like the specimens did during the tests. By using the analyzed results of the FE-models the aim is to calculate and get the stress-strain curves that correspond to the results acquired from the tensile tests.

Expectations, frames and practices of genetic counselling in different contexts of genetic testing

Genetic counselling is a process in which the counsellee receives information and support concerning a genetic disease. This study examines the genetic counselling attached to genetic testing. Since genetic information is increasing alongside new testing technologies and the situations faced at the genetic clinics will therefore be more diverse, it is essential to assess what the expectations directed at genetic counselling are. It is also important to compare how they face the current counselling practices. In this study, the expectations, frames and practices of genetic counselling in different contexts of genetic testing were examined from three different perspectives: First, international guidelines covering genetic counselling were analysed to summarise what is expected from genetic counselling and to study how genetic information is framed. Second, national experts in European countries were asked about the regulations and practices of genetic counselling in their country. Finally, ten counsellees who had visited a genetic clinic were interviewed to analyse their expectations and experiences. The counsellees’ perspective was also approached through the background review of the previous studies on counsellees’ experiences. On the basis of the study, there are basic elements that are expected to be covered in genetic counselling from all perspectives. However, the views concerning bioethics, genetic exceptionalism and psychosocial aspects vary depending on the perspective and on the individual situation. Since there are sometimes more differences than similarities between genetic tests, no universal recommendations for counselling can be applied. The practices of genetic counselling should be defined situationally, emphasising the individual needs over the genes.

Making the impact on research and society : nichesourcing of Uralic language material for the benefit of linguistic research and native-speakers

Presentation at the 12th Bibliotheca Baltica Symposium at Södertörn University Library

Guilt, shame, emotion regulation, and social cognition: Understanding their associations with preadolescents' social behavior

In this thesis, two negatively valenced emotions are approached as reflecting children’s self-consciousness, namely guilt and shame. Despite the notable role of emotions in the psychological research, empirical research findings on the links between guilt, shame, and children’s social behavior – and particularly aggression – have been modest, inconsistent, and sometimes contradictory. This thesis contains four studies on the associations of guilt, shame, emotion regulation, and social cognitions with children’s social behavior. The longitudinal material of the thesis was collected as a survey among a relatively large amount of Finnish preadolescents. In Study I, the distinctiveness of guilt and shame in children’s social behavior were investigated. The more specific links of emotions and aggressive behavior were explored in Study II, in which emotion regulation and negative emotionality were treated as the moderators between guilt, shame, and children’s aggressive behavior. The role of emotion management was further evaluated in Study III, in which effortful control and anger were treated as the moderators between domain-specific aggressive cognitions and children’s aggressive behavior. In the light of the results from the Studies II and III, it seems that for children with poor emotion management the effects of emotions and social cognitions on aggressive behavior are straight-forward, whereas effective emotion management allows for reframing the situation. Finally, in Study IV, context effects on children’s anticipated emotions were evaluated, such that children were presented a series of hypothetical vignettes, in which the child was acting as the aggressor. Furthermore, the identity of the witnesses and victim’s reactions were systematically manipulated. Children anticipated the most shame in situations, in which all of the class was witnessing the aggressive act, whereas both guilt and shame were anticipated the most in the situations, in which the victim was reacting with sadness. Girls and low-aggressive children were more sensitive to contextual cues than boys and high-aggressive children. Overall, the results of this thesis suggest that the influences of guilt, shame, and social cognition on preadolescents’ aggressive behavior depend significantly on the nature of individual emotion regulation, as well as situational contexts. Both theoretical and practical implications of this study highlight a need to acknowledge effective emotion management as enabling the justification of one’s own immoral behavior.

Schools as Oral Health Promoters – Evaluation of National Sweet Selling Recommendation and Oral Health Education Material

The aims were to find out 1) if schools’ oral health practices were associated with pupils’ oral health behaviour and whether 2) the national sweet-selling recommendation and 3) distributing oral health material (OHEM) affected schools as oral health promoters. Three independently collected datasets from Finnish upper comprehensive schools (N=988) were used: longitudinal oral health practices data (n=258) with three-year follow up (2007 n=480, 2008 n=508, 2009 n=593) from principals’ online questionnaires, oral health behaviour data from pupils participating in the national School Health Promotion Study (n=970 schools) and oral health education data from health education teachers’ online questionnaires (2008 n=563, 2009 n=477 teachers). Oral health practices data and oral health behaviour data were combined (n=414) to answer aim 1. For aims 2 and 3, oral health practices data and oral health education data were used independently. School sweet selling and an open campus policy were associated with pupils’ use of sweet products and tobacco products during school time. The National Recommendation was quite an effective way to reduce the number of sweet-selling schools, but there were large regional differences and a lack of a clear oral health policy in the schools. OHEM did not increase the proportion of teachers teaching oral health, but teachers started to cover oral health topics more frequently. Women started to use OHEM more often than men did. Schools’ oral health policy should include prohibiting the selling of sweet products in school by legislative actions, enabling healthy alternatives instead, and setting a closed campus policy to protect pupils from school-time sweet consuming and smoking.

Decision making and decision support in service systems

This thesis is a literature study that develops a conceptual model of decision making and decision support in service systems. The study is related to the Ä-Logi, Intelligent Service Logic for Welfare Sector Services research project, and the objective of the study is to develop the necessary theoretical framework to enable further research based on the research project results and material. The study first examines the concepts of service and service systems, focusing on understanding the characteristics of service systems and their implications for decision making and decision support to provide the basis for the development of the conceptual model. Based on the identified service system characteristics, an integrated model of service systems is proposed that views service systems through a number of interrelated perspectives that each offer different, but complementary, implications on the nature of decision making and the requirements for decision support in service systems. Based on the model, it is proposed that different types of decision making contexts can be identified in service systems that may be dominated by different types of decision making processes and where different types of decision support may be required, depending on the characteristics of the decision making context and its decision making processes. The proposed conceptual model of decision making and decision support in service systems examines the characteristics of decision making contexts and processes in service systems, and their typical requirements for decision support. First, a characterization of different types of decision making contexts in service systems is proposed based on the Cynefin framework and the identified service system characteristics. Second, the nature of decision making processes in service systems is proposed to be dual, with both rational and naturalistic decision making processes existing in service systems, and having an important and complementary role in decision making in service systems. Finally, a characterization of typical requirements for decision support in service systems is proposed that examines the decision support requirements associated with different types of decision making processes in characteristically different types of decision making contexts. It is proposed that decision support for the decision making processes that are based on rational decision making can be based on organizational decision support models, while decision support for the decision making processes that are based on naturalistic decision making should be based on supporting the decision makers’ situation awareness and facilitating the development of their tacit knowledge of the system and its tasks. Based on the proposed conceptual model a further research process is proposed. The study additionally provides a number of new perspectives on the characteristics of service systems, and the nature of decision making and requirements for decision support in service systems that can potentially provide a basis for further discussion and research, and support the practice alike.

Energy and raw material consumption analysis of powder bed fusion: case study: CNC machining and laser additive manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, is a powder bed fusion (PBF) type of additive manufacturing (AM) technology used to manufacture metal parts layer by layer by assist of laser beam. The development of the technology from building just prototype parts to functional parts is due to design flexibility. And also possibility to manufacture tailored and optimised components in terms of performance and strength to weight ratio of final parts. The study of energy and raw material consumption in LAM is essential as it might facilitate the adoption and usage of the technique in manufacturing industries. The objective this thesis was find the impact of LAM on environmental and economic aspects and to conduct life cycle inventory of CNC machining and LAM in terms of energy and raw material consumption at production phases. Literature overview in this thesis include sustainability issues in manufacturing industries with focus on environmental and economic aspects. Also life cycle assessment and its applicability in manufacturing industry were studied. UPLCI-CO2PE! Initiative was identified as mostly applied exiting methodology to conduct LCI analysis in discrete manufacturing process like LAM. Many of the reviewed literature had focused to PBF of polymeric material and only few had considered metallic materials. The studies that had included metallic materials had only measured input and output energy or materials of the process and compared to different AM systems without comparing to any competitive process. Neither did any include effect of process variation when building metallic parts with LAM. Experimental testing were carried out to make dissimilar samples with CNC machining and LAM in this thesis. Test samples were designed to include part complexity and weight reductions. PUMA 2500Y lathe machine was used in the CNC machining whereas a modified research machine representing EOSINT M-series was used for the LAM. The raw material used for making the test pieces were stainless steel 316L bar (CNC machined parts) and stainless steel 316L powder (LAM built parts). An analysis of power, time, and the energy consumed in each of the manufacturing processes on production phase showed that LAM utilises more energy than CNC machining. The high energy consumption was as result of duration of production. Energy consumption profiles in CNC machining showed fluctuations with high and low power ranges. LAM energy usage within specific mode (standby, heating, process, sawing) remained relatively constant through the production. CNC machining was limited in terms of manufacturing freedom as it was not possible to manufacture all the designed sample by machining. And the one which was possible was aided with large amount of material removed as waste. Planning phase in LAM was shorter than in CNC machining as the latter required many preparation steps. Specific energy consumption (SEC) were estimated in LAM based on the practical results and assumed platform utilisation. The estimated platform utilisation showed SEC could reduce when more parts were placed in one build than it was in with the empirical results in this thesis (six parts).

Hygro-elasto-plastic behavior of planar orthotropic material

The mechanical and hygroscopic properties of paper and board are factors affecting the whole lifecycle of a product, including paper/board quality, production, converting, and material and energy savings. The progress of shrinkage profiles, loose edges of web, baggy web causing wrinkling and misregistration in printing are examples of factors affecting runnability and end product quality in the drying section and converting processes, where paper or board is treated as a moving web. The structural properties and internal stresses or plastic strain differences built up during production also cause the end-product defects related to distortion of the shape of the product such as sheet or box. The objective of this work was to construct a model capable of capturing the characteristic behavior of hygroscopic orthotropic material under moisture change, during different external in-plane stretch or stress conditions. Two independent experimental models were constructed: the elasto-plastic material model and the hygroexpansivity-shrinkage model. Both describe the structural properties of the sheet with a fiber orientation probability distribution, and both are functions of the dry solids content and fiber orientation anisotropy index. The anisotropy index, introduced in this work, simplifies the procedure of determining the constitutive parameters of the material model and the hygroexpansion coefficients in different in-plane directions of the orthotropic sheet. The mathematically consistent elasto-plastic material model and the dry solids content dependent hygroexpansivity have been constructed over the entire range from wet to dry. The presented elastoplastic and hygroexpansivity-shrinkage models can be used in an analytical approach to estimate the plastic strain and shrinkage in simple one-dimensional cases. For studies of the combined and more complicated effects of hygro-elasto-plastic behavior, both models were implemented in a finite element program for a numerical solution. The finite element approach also offered possibilities for studying different structural variations of orthotropic planar material, as well as local buckling behavior and internal stress situations of the sheet or web generated by local strain differences. A comparison of the simulation examples presented in this work to results published earlier confirms that the hygro-elasto-plastic model provides at least qualitatively reasonable estimates. The application potential of the hygro-elasto-plastic model is versatile, including several phenomena and defects appearing in the drying, converting and end-use conditions of the paper or board webs and products, or in other corresponding complex planar materials.

How to increase brand quality perception with audiovisual content? : Exploring the role of emotions in B2C and B2B contexts

This study discusses how audiovisual content can influence brand quality perceptions. The purpose of this study is to explore how audiovisual content creation can increase brand quality perceptions. This research problem is addressed with three sub questions, which aim at clarifying the role of emotions between content marketing and brand quality perception, explaining how different functions of audiovisual content can increase brand quality perception, and by identifying and comparing the key differences in content creation in business-to-consumer and business-to-businesscontexts. The theoretical background of the study is in brand personality, consumer emotions, consumerbrand relationships, content marketing and B2B branding literature. The empirical research part includes a single-case study. The case company was a Swiss startup that wished to build a highquality brand for both B2C and B2B segments. The empirical data was collected in September 2014. Eight interviews were conducted; seven with target segment representatives and one with an existing customer of the case company. The empirical findings were analyzed with thematic analysis and finally a 5-stage framework was created based on the findings of the research, offering a guideline for high-quality content creation. This study finds that emotions play an important role in brand quality perceptions. Psychological processes, emotion, cognition and conation, influence the engagement process of the target segment which ultimately can lead to activation and electronic word-of-mouth. Brand quality perception is the result of the overall emotion of the brand. The overall emotion derives from brand personality, brand concept, product attributes and utilitarian benefits of the brand. The entertaining and educational functions of the audiovisual content can target and evoke these emotional processes, and result in increased quality perceptions. In the B2B context, emotions are found to play a relatively smaller role in the quality perception processes. However, the significance of emotions cannot be ignored, since they can emphasize the value for the buying organization, and build on the trust and loyalty among the potential customers. The final framework presents five stages of content creation that ultimately improve brand quality perceptions. These stages help marketers to design and implement their content and evoke positive emotions in their target segment as part of a quality-based marketing strategy. Further research is warranted to quantitatively test the generalizability of the framework. Further research is also suggested to make the framework adaptable to different stages of the brand life cycle.

Optical spectroscopy of organic material based on C60

The structure and optical properties of thin films based on C60 materials are studied. Reproducible vacuum method of thin fullerene films production with Cd impurity on Si, glass and mica surfaces is developed. Surface morphology of the films are investigated by AFM and SEM methods. The ab initio quantum - chemical calculations of the geometry, total energy and excited energy states of complex fullerene- cadmium telluride supramolecules are performed. Photoluminescence spectra of composite thin films based on C60 before and after X-ray irradiation were measured. The intensity of additional peaks is defined as the charge composition due to the type of substrate. These results are interpreted as an appearance of the dipole-allowed transitions in the fullerene excited singlet states spectrum cause of an interference with cadmium telluride. X-ray irradiated films were investigated, and additional peaks in photoluminescence spectra were detected. These peaks appear as a result of molecular complexes formation from C60CdTe mixture and dimerization of the films. Density functional B3LYP quantum-chemical calculations for C60CdTe, molecular complexes, (C60)2 and C120O dimers were performed to elucidate some experimental results.

Conceptualizing and counteracting the bullying dynamic: Classroom and school contexts matter

Guided by the social-ecological conceptualization of bullying, this thesis examines the implications of classroom and school contexts—that is, students’ shared microsystems—for peer-to-peer bullying and antibullying practices. Included are four original publications, three of which are empirical studies utilizing data from a large Finnish sample of students in the upper grade levels of elementary school. Both self- and peer reports of bullying and victimization are utilized, and the hierarchical nature of the data collected from students nested within school ecologies is accounted for by multilevel modeling techniques. The first objective of the thesis is to simultaneously examine risk factors for victimization at individual, classroom, and school levels (Study I). The second objective is to uncover the individual- and classroom-level working mechanisms of the KiVa antibullying program which has been shown to be effective in reducing bullying problems in Finnish schools (Study II). Thirdly, an overview of the extant literature on classroom- and school-level contributions to bullying and victimization is provided (Study III). Finally, attention is paid to the assessment of victimization and, more specifically, to how the classroom context influences the concordance between self- and peer reports of victimization (Study IV). Findings demonstrate the multiple ways in which contextual factors, and importantly students’ perceptions thereof, contribute to the bullying dynamic and efforts to counteract it. Whereas certain popular beliefs regarding the implications of classroom and school contexts do not receive support, the role of peer contextual factors and the significance of students’ perceptions of teachers’ attitudes toward bullying are highlighted. Directions for future research and school-based antibullying practices are suggested.

Designing new learning experiences? : exploring corporate E-learners’ self-regulated learning

The context of this study is corporate e-learning, with an explicit focus on how digital learning design can facilitate self-regulated learning (SRL). The field of e-learning is growing rapidly. An increasing number of corporations use digital technology and elearning for training their work force and customers. E-learning may offer economic benefits, as well as opportunities for interaction and communication that traditional teaching cannot provide. However, the evolving variety of digital learning contexts makes new demands on learners, requiring them to develop strategies to adapt and cope with novel learning tools. This study derives from the need to learn more about learning experiences in digital contexts in order to be able to design these properly for learning. The research question targets how the design of an e-learning course influences participants’ self-regulated learning actions and intentions. SRL involves learners’ ability to exercise agency in their learning. Micro-level SRL processes were targeted by exploring behaviour, cognition, and affect/motivation in relation to the design of the digital context. Two iterations of an e-learning course were tested on two groups of participants (N=17). However, the exploration of SRL extends beyond the educational design research perspective of comparing the effects of the changes to the course designs. The study was conducted in a laboratory with each participant individually. Multiple types of data were collected. However, the results presented in this thesis are based on screen observations (including eye tracking) and video-stimulated recall interviews. These data were integrated in order to achieve a broad perspective on SRL. The most essential change evident in the second course iteration was the addition of feedback during practice and the final test. Without feedback on actions there was an observable difference between those who were instruction-directed and those who were self-directed in manipulating the context and, thus, persisted whenever faced with problems. In the second course iteration, including the feedback, this kind of difference was not found. Feedback provided the tipping point for participants to regulate their learning by identifying their knowledge gaps and to explore the learning context in a targeted manner. Furthermore, the course content was consistently seen from a pragmatic perspective, which influenced the participants’ choice of actions, showing that real life relevance is an important need of corporate learners. This also relates to assessment and the consideration of its purpose in relation to participants’ work situation. The rigidity of the multiple choice questions, focusing on the memorisation of details, influenced the participants to adapt to an approach for surface learning. It also caused frustration in cases where the participants’ epistemic beliefs were incompatible with this kind of assessment style. Triggers of positive and negative emotions could be categorized into four levels: personal factors, instructional design of content, interface design of context, and technical solution. In summary, the key design choices for creating a positive learning experience involve feedback, flexibility, functionality, fun, and freedom. The design of the context impacts regulation of behaviour, cognition, as well as affect and motivation. The learners’ awareness of these areas of regulation in relation to learning in a specific context is their ability for design-based epistemic metareflection. I describe this metareflection as knowing how to manipulate the context behaviourally for maximum learning, being metacognitively aware of one’s learning process, and being aware of how emotions can be regulated to maintain volitional control of the learning situation. Attention needs to be paid to how the design of a digital learning context supports learners’ metareflective development as digital learners. Every digital context has its own affordances and constraints, which influence the possibilities for micro-level SRL processes. Empowering learners in developing their ability for design-based epistemic metareflection is, therefore, essential for building their digital literacy in relation to these affordances and constraints. It was evident that the implementation of e-learning in the workplace is not unproblematic and needs new ways of thinking about learning and how we create learning spaces. Digital contexts bring a new culture of learning that demands attitude change in how we value knowledge, measure it, define who owns it, and who creates it. Based on the results, I argue that digital solutions for corporate learning ought to be built as an integrated system that facilitates socio-cultural connectivism within the corporation. The focus needs to shift from designing static e-learning material to managing networks of social meaning negotiation as part of a holistic corporate learning ecology.

Defining Contexts in Context-Free Grammars

This thesis introduces an extension of Chomsky’s context-free grammars equipped with operators for referring to left and right contexts of strings.The new model is called grammar with contexts. The semantics of these grammars are given in two equivalent ways — by language equations and by logical deduction, where a grammar is understood as a logic for the recursive definition of syntax. The motivation for grammars with contexts comes from an extensive example that completely defines the syntax and static semantics of a simple typed programming language. Grammars with contexts maintain most important practical properties of context-free grammars, including a variant of the Chomsky normal form. For grammars with one-sided contexts (that is, either left or right), there is a cubic-time tabular parsing algorithm, applicable to an arbitrary grammar. The time complexity of this algorithm can be improved to quadratic,provided that the grammar is unambiguous, that is, it only allows one parsefor every string it defines. A tabular parsing algorithm for grammars withtwo-sided contexts has fourth power time complexity. For these grammarsthere is a recognition algorithm that uses a linear amount of space. For certain subclasses of grammars with contexts there are low-degree polynomial parsing algorithms. One of them is an extension of the classical recursive descent for context-free grammars; the version for grammars with contexts still works in linear time like its prototype. Another algorithm, with time complexity varying from linear to cubic depending on the particular grammar, adapts deterministic LR parsing to the new model. If all context operators in a grammar define regular languages, then such a grammar can be transformed to an equivalent grammar without context operators at all. This allows one to represent the syntax of languages in a more succinct way by utilizing context specifications. Linear grammars with contexts turned out to be non-trivial already over a one-letter alphabet. This fact leads to some undecidability results for this family of grammars