Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T-10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 1720 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 5080 KIAS (90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Cellular responses to stress and kinase signaling activation : apoptosis and differentiation

Stressignaler avkänns många gånger av membranbundna proteiner som översätter signalerna till kemisk modifiering av molekyler, ofta proteinkinaser Dessa kinaser överför de avkodade budskapen till specifika transkriptionsfaktorer genom en kaskad av sekventiella fosforyleringshändelser, transkriptionsfaktorerna aktiverar i sin tur de gener som behövs för att reagera på stressen. En av de mest kända måltavlorna för stressignaler är transkriptionsfaktor AP-1 familjemedlemen c-Jun. I denna studie har jag identifierat den nukleolära proteinet AATF som en ny regulator av c-Jun-medierad transkriptionsaktivitet. Jag visar att stresstimuli inducerar omlokalisering av AATF vilket i sin tur leder till aktivering av c-Jun. Den AATF-medierad ökningen av c-Jun-aktiviteten leder till en betydande ökning av programmerad celldöd. Parallellt har jag vidarekarakteriserat Cdk5/p35 signaleringskomplexet som tidigare har identifierats i vårt laboratorium som en viktig faktor för myoblastdifferentiering. Jag identifierade den atypiska PKCξ som en uppströms regulator av Cdk5/p35-komplexet och visar att klyvning och aktivering av Cdk5 regulatorn p35 är av fysiologisk betydelse för differentieringsprocessen och beroende av PKCξ aktivitet. Jag visar att vid induktion av differentiering fosforylerar PKCξ p35 vilket leder till calpain-medierad klyvning av p35 och därmed ökning av Cdk5-aktiviteten. Denna avhandling ökar förståelsen för de regulatoriska mekanismer som styr c-Jun-transkriptionsaktiviteten och c-Jun beroende apoptos genom att identifiera AATF som en viktig faktor. Dessutom ger detta arbete nya insikter om funktionen av Cdk5/p35-komplexet under myoblastdifferentiering och identifierar PKCξ som en uppströms regulator av Cdk5 aktivitet och myoblast differentiering.

Lämmityslinjan kokoonpanosolujen tehostaminen Lean-työkaluilla

Diplomityön tarkoitus on tehostaa lämmityslinjan kokoonpanosoluja käyttämällä erilaisia Lean – työkaluja. Pyrkimys on lisätä järjestystä 5S - työkalun avulla sekä selvittää lämmitinlinjan työntekijän ajankäyttö. Lämmitinlinjan suurimmat ongelmat selvitetään häviön mittauksen ja kartoituksen avulla. Työntekijöiden työmenetelmät tutkitaan käyttämällä MTM (Methods-Time Measurement)– menetelmää, jossa yksittäinen työsuoritus kuvataan videolle. Video pisteytetään ja työntekijän liikkeet analysoidaan. Videon pohjalta havaitaan kehityskohteet työpisteissä ja työmenetelmissä, ja ne organisoidaan sekä standardoidaan uudestaan. Materiaalivirtauksen ongelma ratkaistaan siirtämällä komponentit kokoonpanosoluun uuden materiaalipalvelijan toimesta. Menetelmäkehityksen ja paremman järjestyksen avulla kokoonpanosolun tuottavuutta parannetaan 30 prosenttia verrattuna alkuperäiseen tilanteeseen. Lämmitinlinjan häviön mittauksella saavutetaan ymmärrys osaston suurimmista pullonkauloista. Mittauksen avulla tiedetään yksittäisten ongelmien esiintymistiheydet ja koneiden kapasiteettihäviöt. Lämmitinlinjaston tehostaminen tulevaisuudessa vaatii häviöiden alkuperäisten ongelmien ratkaisua.

Power-line-communication-based data transmission concept for an LVDC electricity distribution network – Analysis and implementation

Communications play a key role in modern smart grids. New functionalities that make the grids ‘smart’ require the communication network to function properly. Data transmission between intelligent electric devices (IEDs) in the rectifier and the customer-end inverters (CEIs) used for power conversion is also required in the smart grid concept of the low-voltage direct current (LVDC) distribution network. Smart grid applications, such as smart metering, demand side management (DSM), and grid protection applied with communications are all installed in the LVDC system. Thus, besides remote connection to the databases of the grid operators, a local communication network in the LVDC network is needed. One solution applied to implement the communication medium in power distribution grids is power line communication (PLC). There are power cables in the distribution grids, and hence, they may be applied as a communication channel for the distribution-level data. This doctoral thesis proposes an IP-based high-frequency (HF) band PLC data transmission concept for the LVDC network. A general method to implement the Ethernet-based PLC concept between the public distribution rectifier and the customerend inverters in the LVDC grid is introduced. Low-voltage cables are studied as the communication channel in the frequency band of 100 kHz–30 MHz. The communication channel characteristics and the noise in the channel are described. All individual components in the channel are presented in detail, and a channel model, comprising models for each channel component is developed and verified by measurements. The channel noise is also studied by measurements. Theoretical signalto- noise ratio (SNR) and channel capacity analyses and practical data transmission tests are carried out to evaluate the applicability of the PLC concept against the requirements set by the smart grid applications in the LVDC system. The main results concerning the applicability of the PLC concept and its limitations are presented, and suggestion for future research proposed.

The consequences of e-HRM on line managers

The purpose of this research was to provide a deeper insight into the consequences of electronic human resource management (e-HRM) for line managers. The consequences are viewed as used information system (IS) potentials pertaining to the moderate voluntaristic category of consequences. Due to the need to contextualize the research and draw on line managers’ personal experiences, a qualitative approach in a case study setting was selected. The empirical part of the research is loosely based on literature on HRM and e-HRM and it was conducted in an industrial private sector company. In this thesis, method triangulation was utilized, as nine semi-structured interviews, conducted in a European setting, created the main method for data collection and analysis. Other complementary data such as HRM documentation and statistics of e-HRM system usage were utilized as background information to help to put the results into context. E-HRM has partly been taken into use in the case study company. Line managers tend to use e-HRM when a particular task requires it, but they are not familiar with all the features and possibilities which e-HRM has to offer. The advantages of e-HRM are in line with the company’s goals. The advantages are e.g. an transparency of data, process consistency, and having an efficient and easy-to-use tool at one’s disposal. However, several unintended, even contradictory, and mainly negative outcomes can also be identified, such as over-complicated processes, in-security in use of the tool, and the lack of co-operation with HR professionals. The use of e-HRM and managers’ perceptions regarding e-HRM affect the way in which managers perceive the consequences of e-HRM on their work. Overall, the consequences of e-HRM are divergent, even contradictory. The managers who considered e-HRM mostly beneficial to their work found that e-HRM affects their work by providing information and increasing efficiency. Those managers who mostly perceived challenges in e-HRM did not think that e-HRM had affected their role or their work. Even though the perceptions regarding e-HRM and its consequences might reflect the strategies, the distribution of work, and the ways of working in all HRM in general and can’t be generalized as such, this research contributed to the field of e-HRM and it provides new perspectives to e-HRM in the case study organization and in the academic field in general.

Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T- 10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 17−20 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 50−80 KIAS (∼90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Biopolttoaineiden on-line -laadunmittauksen hyödyt energiantuotannossa

Biopolttoaineet ovat tärkeä energianlähde suomalaisessa energiantuotannossa. Biopoltto- aineille on kuitenkin ominaista laadun vaihtelevuus. Yksi tärkeimmistä laatutekijöistä on kosteus, joka vaikuttaa myös polttoaineen energiasisältöön. Laatutekijät puolestaan vai- kuttavat polttoainekäsittelyyn, polttoprosessiin ja koko laitoksen hyötysuhteeseen. Tämän työn tarkoituksena oli tutkia voisiko biopolttoaineiden online-laadunmittaus tuoda lisäarvoa energiantuotantolaitokselle. Esimerkkinä käytettiin yhtä online-laadunmittaus- sovellusta, InrayFuel-röntgenmittausjärjestelmää. Sillä voidaan seurata biopolttoaineiden kosteutta ja polttoaineen sisältämiä vierasaineita. Työssä on laadittu kustannusanalyysi, jolla pyritään selvittämään, onko nykyisen kertaluontoisen mittausmenetelmän korvaami- nen jatkuvatoimisella kannattavaa. Esimerkkilaitoksena on Etelä-Savon Energian Pur- sialan voimalaitos, jossa röntgenmittausjärjestelmään on testattu. Saatujen tulosten mukaan investoiminen esimerkkimittausjärjestelmään maksaisi itsensä takaisin alle vuodessa. Kun laitoksella pystytään seuraamaan polttoaineen laatua jatkuva- toimisesti, laadunhallinta paranee ja sitä kautta voidaan saavuttaa kustannussäästöjä. Polt- toaineesta johtuvat häiriötilanteet vähenevät, polttoaine on mahdollista optimoida edulli- semmaksi polton kannalta ja poltto-olosuhteita voidaan säätää paremmin, jolloin päästöt vähenevät ja hyötysuhde kasvaa. Työssä käytetty laskenta analysoi kuitenkin hyvin ylei- sellä tasolla, sillä käytössä ei ollut laitoksen omaa taselaskentajärjestelmää. Laskenta siis sisältää paljon oletuksia. Tämän ja rohkaisevien tulosten vuoksi tutkimusta jatkuvatoimi- sen laadunmittauksen hyödyistä kannattaa tehdä enemmän.

On-line determination of residual collector concentration in flotation process

Valuable minerals can be recovered by using froth flotation. This is a widely used separation technique in mineral processing. In a flotation cell hydrophobic particles attach on air bubbles dispersed in the slurry and rise on the top of the cell. Valuable particles are made hydrophobic by adding collector chemicals in the slurry. With the help of a frother reagent a stable froth forms on the top of the cell and the froth with valuable minerals, i.e. the concentrate, can be removed for further processing. Normally the collector is dosed on the basis of the feed rate of the flotation circuit and the head grade of the valuable metal. However, also the mineral composition of the ore affects the consumption of the collector, i.e. how much is adsorbed on the mineral surfaces. Therefore it is worth monitoring the residual collector concentration in the flotation tailings. Excess usage of collector causes unnecessary costs and may even disturb the process. In the literature part of the Master’s thesis the basics of flotation process and collector chemicals are introduced. Capillary electrophoresis (CE), an analytical technique suitable for detecting collector chemicals, is also reviewed. In the experimental part of the thesis the development of an on-line CE method for monitoring the concentration of collector chemicals in a flotation process and the results of a measurement campaign are presented. It was possible to determine the quality and quantity of collector chemicals in nickel flotation tailings at a concentrator plant with the developed on-line CE method. Sodium ethyl xanthate and sodium isopropyl xanthate residuals were found in the tailings and slight correlation between the measured concentrations and the dosage amounts could be seen.

Software product line for power converters

Työn tilaajana toimi Visedo Oy. Työn tavoitteina oli tutkia Visedo Oy:n ohjelmistokehityksen nykytila, tunnistaa seuraavat parannuskohteet ja antaa ohjeita havaittujen parannuskohteiden korjaamiseksi. Visedo Oy:n tehonmuokkain ohjelmistokehityksen nykytilaa käsiteltiin neljän valitun osa-alueen näkökulmasta: ohjelmistoarkkitehtuurityyli, komponenttipohjainen ohjelmistokehitys, ohjelmistotuotelinjojen kehitysmenetelmät ja ohjelmistovariaatioiden hallinta. Valituilla osa-alueilla havaittujen parannuskohteiden perusteella annettiin korjausehdotuksia: ohjelmistoarkkitehtuurin rakenteeseen, komponenttien jakautumiselle, komponenttien koostamiselle ja komponenttien versioinnille. Lisäksi ehdotettiin uudenlaista ohjelmistotuotelinja rakennetta, joka yhdistää kerros- ja komponenttipohjaiset arkkitehtuurityylit mahdollistaen ominaisuuksiltaan eroavien tehonmuokkain ohjelmistojen hallinnan.

Pinoamislaitteen suunnittelu vetokoneen jälkeiselle linjalle

Työn tavoitteena oli suunnitella vetokoneen linjalle pinoamislaite. Laitteen tehtävänä on pinota yksittäin vetokoneelta tulevista tuotteista asiakasvaatimusten mukaisia pinoja. Laitteen suunnittelu toteutettiin käyttämällä systemaattisen koneensuunnittelun metodia. Diplomityö rajattiin koskemaan laitteen mekaanisten ratkaisujen suunnittelua. Suunnittelussa huomioitiin linjan asettamat vaatimukset, jotka koskevat sekä tuotantomäärää että tilojen käyttöä. Laitteen suunnittelussa ja mallinnuksessa käytettiin Solidworksin 3D-mallinnusohjelmaa. Mallinnettuja ratkaisuvaihtoehtoja verrattiin keskenään. Parhaiten vaatimusluettelossa esitetyt vaatimukset täyttänyt ratkaisumalli valittiin kehitettäväksi. Suunnitellusta laitteesta valmistettiin työpiirustukset sekä kokoonpanokuvat.

To Divide or Not to Divide; MicroRNAs and Small Compounds as Modulators of Mitosis

Mitosis is under the stringent quality control of the spindle assembly checkpoint (SAC). However, in cancer cells this control can fail, leading to excessive cellular proliferation and ultimately to the formation of a tumor. Novel cancer cell selective therapies are needed to stop the uncontrolled cell proliferation and tumor growth. The aim of the research presented in this thesis was to identify microRNAs (miRNAs) that could play a role in cancer cell proliferation as well as low molecular weight (LMW) compounds that could interfere with cell division. The findings could be used to develop better cancer diagnostics and therapies in the future. First, a high-throughput screen (HTS) was performed to identify LMW compounds that possess a similar chemical interaction field as rigosertib, an anti-cancer compound undergoing clinical trials. A compound termed Centmitor-1 was discovered that phenocopied the cellular impact of rigosertib by affecting the microtubule dynamics. Next, another HTS aimed at identifying compounds that would target the Hec1 protein, which mediates the interaction between spindle microtubules and chromosomes. Perturbation of this connection should prevent cell division and induce cell death. A compound termed VTT-006 was discovered that abrogated mitosis in several cell line models and exhibited binding to Hec1 in vitro. Lastly, using a cell-based HTS two miRNAs were identified that affected cancer cell proliferation via Aurora B kinase, which is an important mitotic regulator. MiR-378a-5p was found to indirectly suppress the production of the kinase whereas let-7b showed direct binding to the 3’UTR of Aurora B mRNA and repressed its translation. The miRNA-mediated perturbation of Aurora B induced defects in mitosis leading to abnormal chromosome segregation and induction of aneuploidy. The results of this thesis provide new information on miRNA signaling in cancer, which could be utilized for diagnostic purposes. Moreover, the thesis introduces two small compounds that may benefit future drug research.

Vibration analysis of a power take-off line

Gear rattle is a phenomenon that occurs when idling or lightly loaded gears collide due to engine’s torque fluctuations. This behaviour is related to vibration behaviour of the transmission system. Aim of this master’s thesis is to evaluate Adams and Adams/Machinery as a simulation tools for modelling the rattle e ect in a transmission system. A case study of tractor’s power take-o driveline, suspected to be prone to rattle, is performed in this work. Modelling methods used by Adams in this type of study are presented in the theory section while simulation model build with the software during this work is presented in the results. The Machinery toolbox is used to create gears and bearings while other model components are created with standard Adams tool set. Geometries and excitations are exported from other softwares. Results were obtained from multiple variations of a base model. These result sets and literature review suggest that Adams/Machinery may not be the most suitable tool for rattle analysis. While the system behaviour was partially captured, for accurate modelling user-written routines must be used which may be more easily performed with other tools. Further research about this topic is required.

Computational models for and from biology : simple gene assembly and reaction systems

The advancement of science and technology makes it clear that no single perspective is any longer sufficient to describe the true nature of any phenomenon. That is why the interdisciplinary research is gaining more attention overtime. An excellent example of this type of research is natural computing which stands on the borderline between biology and computer science. The contribution of research done in natural computing is twofold: on one hand, it sheds light into how nature works and how it processes information and, on the other hand, it provides some guidelines on how to design bio-inspired technologies. The first direction in this thesis focuses on a nature-inspired process called gene assembly in ciliates. The second one studies reaction systems, as a modeling framework with its rationale built upon the biochemical interactions happening within a cell. The process of gene assembly in ciliates has attracted a lot of attention as a research topic in the past 15 years. Two main modelling frameworks have been initially proposed in the end of 1990s to capture ciliates’ gene assembly process, namely the intermolecular model and the intramolecular model. They were followed by other model proposals such as templatebased assembly and DNA rearrangement pathways recombination models. In this thesis we are interested in a variation of the intramolecular model called simple gene assembly model, which focuses on the simplest possible folds in the assembly process. We propose a new framework called directed overlap-inclusion (DOI) graphs to overcome the limitations that previously introduced models faced in capturing all the combinatorial details of the simple gene assembly process. We investigate a number of combinatorial properties of these graphs, including a necessary property in terms of forbidden induced subgraphs. We also introduce DOI graph-based rewriting rules that capture all the operations of the simple gene assembly model and prove that they are equivalent to the string-based formalization of the model. Reaction systems (RS) is another nature-inspired modeling framework that is studied in this thesis. Reaction systems’ rationale is based upon two main regulation mechanisms, facilitation and inhibition, which control the interactions between biochemical reactions. Reaction systems is a complementary modeling framework to traditional quantitative frameworks, focusing on explicit cause-effect relationships between reactions. The explicit formulation of facilitation and inhibition mechanisms behind reactions, as well as the focus on interactions between reactions (rather than dynamics of concentrations) makes their applicability potentially wide and useful beyond biological case studies. In this thesis, we construct a reaction system model corresponding to the heat shock response mechanism based on a novel concept of dominance graph that captures the competition on resources in the ODE model. We also introduce for RS various concepts inspired by biology, e.g., mass conservation, steady state, periodicity, etc., to do model checking of the reaction systems based models. We prove that the complexity of the decision problems related to these properties varies from P to NP- and coNP-complete to PSPACE-complete. We further focus on the mass conservation relation in an RS and introduce the conservation dependency graph to capture the relation between the species and also propose an algorithm to list the conserved sets of a given reaction system.

Post-transaction brand and model line-up integration in the automotive industry: Case studies of European companies as target of acquisitions by Chinese and Indian multinational corporations

Corporations practice company acquisitions in order to create shareholder’s value. During the last few decades, the companies in emerging markets have become active in the acquisition business. During the last decade, large and significant acquisitions have occurred especially in automotive industry. While domestic markets have become too competitive and companies are lacking required capabilities, they seek possibilities to expand into Western markets by attaining valuable assets through acquisitions of developed country corporations. This study discusses the issues and characteristics of these acquisitions through case studies. The purpose of this study was to identify the acquisition motives and strategies for post-transaction brand and product integration as well as analyze the effect of the motives to the integration strategy. The cases chosen for the research were Chinese Geely acquiring Swedish Volvo in 2010 and Indian Tata Motors buying British Jaguar Land Rover in 2008. The main topics were chosen according to their significance for companies in automotive industry as well as those are most visible parts for consumers. The study is based on qualitative case study methods, analyzing secondary data from academic papers and news articles as well as companies’ own announcements e.g. stock exchange and press releases. The study finds that the companies in the cases mainly possessed asset-seeking and market-seeking motives. In addition, the findings refer to rather minimal post-acquisition brand and product integration strategies. Mainly the parent companies left the target company autonomous to make their own business strategies and decisions. The most noticeable integrations were in the product development and production processes. Through restructuring the product architectures, the companies were able to share components and technology between product families and brands, which results in cutting down costs and in increase of profitability and efficiency. In the Geely- Volvo case, the strategy focused more on component sharing and product development know-how, whereas in Tata Motors-Jaguar Land Rover case, the main actions were to cut down costs through component sharing and combine production and distribution networks especially in Asian markets. However, it was evident that in both cases the integration and technology sharing were executed cautiously to prevent on harming the valuable image of the luxury brand. This study has concluded that the asset-seeking motives have significant influence on the posttransaction brand and model line-up integration strategies. By taking a cautious approach in acquiring assets, such as luxury brand, the companies in the cases have implemented a successful post-acquisition strategy and managed to create value for the shareholders at least in short-term. Yritykset harjoittavat yritysostoja luodakseen osakkeenomistajille lisäarvoa. Viimeisten muutamien vuosikymmenien aikana yritykset kehittyvissä maissa ovat myös aktivoituneet yritysostoissa. Viimeisen vuosikymmenen aikana erityisesti autoteollisuudessa on esiintynyt suuria ja merkittäviä yritysostoja. Koska kilpailu kotimaan markkinoilla on kiristynyt ja yritykset ovat vailla vaadittavia valmiuksia, ne etsivät mahdollisuuksiaan laajentaa länsimaisiin markkinoihin hankkimalla arvokkaita etuja kehittyneiden maiden yrityksistä yritysostojen avulla. Tämä tutkimus pohtii näiden yritysostojen olennaisia kysymyksiä ja ominaisuuksia casetutkimuksien kautta. Tutkimuksen tarkoitus oli tunnistaa sekä yritysostojen motiiveja ja brändi- ja mallisto-integraation strategioita että analysoida kyseisten motiivien vaikutusta integraatiostrategiaan. Tapaus-tutkimuksiksi valittiin kiinalaisen Geelyn yritysosto ruotsalaisesta Volvosta vuonna 2010 ja intialaisen Tata Motorsin yritysosto englantilaisesta Jaguar Land Roverista vuonna 2008. Tutkimus on kvalitatiivinen case-tutkimus ja siinä analysoidaan toissijaista tietoa sekä akateemisten ja uutisartikkeleiden että yritysten omien ilmoitusten, kuten pörssi- ja lehdistötiedotteiden, kautta. Tutkimuksen tulokset osoittavat, että tutkittujen yritysten toiminnat perustuivat motiiveihin, joita ajoivat etujen and uusien markkinoiden tarve. Sen lisäksi tutkimustulokset osoittivat, että yritysoston jälkeinen brändi- ja mallisto-integraatio pidettiin minimaalisena. Pääasiallisesti kohdeyrityksille jätettiin autonomia tehdä omat liikkeenjohdolliset päätökset yritysstrategioihin liittyen. Huomattavimmat integraatiot koskivat tuotekehityksellisiä ja tuotannollisia prosesseja. Kehittämällä uudelleen tuotearkkitehtuureja, yritykset pystyivät jakamaan komponentteja ja teknologiaa tuoteperheiden ja brändien välillä. Tämä mahdollisti kustannusleikkauksia sekä kannattavuuden ja tehokkuuden parantamista. Geely-Volvo –tapauksessa integraatiostrategia keskittyi komponenttien jakamiseen yhteisten tuotearkkitehtuurien avulla ja tuotekehityksen ammattitaitoon, kun taas Tata Motors-JLR –tapauksessa päätoiminnat olivat kustannuksien leikkaus sekä tuotannon ja jakeluverkoston yhdistäminen erityisesti Aasian maissa. Yhteistä yrityskaupoissa oli, että brändi- ja mallisto-integraatio sekä teknologian jakaminen suoritettiin varoen ehkäistäkseen arvokkaiden luksus-brändien tuotekuvan vahingoittamista. Tutkimuksen lopputulokset osoittavat, että yrityskaupan motiiveilla on huomattava vaikutus brändija mallisto-integraation strategiaan. Toteuttamalla varovaista lähestymistapaa luksus-brändin hankinnassa ja integraatiossa, yritykset ovat onnistuneet luomaan lisäarvoa osakkeenomistajille vähintään lyhyellä aikavälillä.