Investigation of Oxygen Cutting Process in Solid-State Welding

The oxygen cutting is a thermal cutting process, in which metal is heated locally up to its ignition temperature and burnt off by oxygen blast. Oxygen cutting can be used to remove upset metal of a hollow bar occurred due to solid-state welding process. The main goal of this research was to establish a connection between oxygen blasts and mass of metal removed and relate findings to production to suggest improvements to the current process. This master´s thesis describes the designing and building of a test rig for oxygen blowing measurements. It also contains all executed tests and test results, which were carried out. There are different cutting parameters which were studied as well as their effect on cutting process. The oxygen cutting process, used in solid-state welding process, can be improved by the test results.

Advanced orbital pipe welding

Since the introduction of automatic orbital welding in pipeline application in 1961, significant improvements have been obtained in orbital pipe welding systems. Requirement of more productive welding systems for pipeline application forces manufacturers to innovate new advanced systems and welding processes for orbital welding method. Various methods have been used to make welding process adaptive, such as visual sensing, passive visual sensing, real-time intelligent control, scan welding technique, multi laser vision sensor, thermal scanning, adaptive image processing, neural network model, machine vision, and optical sensing. Numerous studies are reviewed and discussed in this Master’s thesis and based on a wide range of experiments which already have been accomplished by different researches the vision sensor are reported to be the best choice for adaptive orbital pipe welding system. Also, in this study the most welding processes as well as the most pipe variations welded by orbital welding systems mainly for oil and gas pipeline applications are explained. The welding results show that Gas Metal Arc Welding (GMAW) and its variants like Surface Tension Transfer (STT) and modified short circuit are the most preferred processes in the welding of root pass and can be replaced to the Gas Tungsten Arc Welding (GTAW) in many applications. Furthermore, dual-tandem gas metal arc welding technique is currently considered the most efficient method in the welding of fill pass. Orbital GTAW process mostly is applied for applications ranging from single run welding of thin walled stainless tubes to multi run welding of thick walled pipes. Flux cored arc welding process is faster process with higher deposition rate and recently this process is getting more popular in pipe welding applications. Also, combination of gas metal arc welding and Nd:YAG laser has shown acceptable results in girth welding of land pipelines for oil and gas industry. This Master’s thesis can be implemented as a guideline in welding of pipes and tubes to achieve higher quality and efficiency. Also, this research can be used as a base material for future investigations to supplement present finding.

Usability of laser–arc hybrid welding processes in industrial applications

Metal industries producing thick sections have shown increasing interest in the laser–arc hybrid welding process because of its clear advantages compared with the individual processes of autogenous laser welding and arc welding. One major benefit of laser–arc hybrid welding is that joints with larger gaps can be welded with acceptable quality compared to autogenous laser welding. The laser-arc hybrid welding process has good potential to extend the field of applications of laser technology, and provide significant improvements in weld quality and process efficiency in manufacturing applications. The objective of this research is to present a parameter set-up for laser–arc hybrid welding processes, introduce a methodical comparison of the chosen parameters, and discuss how this technology may be adopted in industrial applications. The research describes the principles, means and applications of different types of laser–arc hybrid welding processes. Conducted experiment processing variables are presented and compared using an analytical model which can also be used for predictive simulations. The main argument in this thesis is that profound understanding of the advanced technology of laser-arc hybrid welding will help improve the productivity of welding in industrial applications. Based on a review of the current knowledge base, important areas for further research are also identified. This thesis consists of two parts. The first part introduces the research topic and discusses laser–arc hybrid welding by characterizing its mechanism and most important variables. The second part comprises four research papers elaborating on the performance of laser– arc hybrid welding in the joining of metals. The study uses quantitative and qualitative research methods which include in-depth, interpretive analyses of results from a number of research groups. In the interpretive analysis, the emphasis is placed on the relevance and usefulness of the investigative results drawn from other research publications. The results of this study contribute to research on laser–arc hybrid welding by increasing understanding of how old and new perspectives on laser–arc hybrid welding are evidenced in industry. The research methodology applied permits continued exploration of how laser–arc hybrid welding and various process factors influence the overall quality of the weld. Thestudy provides a good foundation for future research, creates improved awareness of the laser–arc hybrid welding process, and assists the metal industry to maximize welding productivity.

Challenges of business process automation for small and medium enterprises

The aim of the study was to examine problems that small and medium enterprises are facing during the implementation of business process automation projects. Study reveals problems from the point of view of companies who are implementing automation projects and from the point of view of IT-integrators who are specifying in IT solutions for small and medium companies.

Spectroscopic monitoring during laser welding of aluminium alloy

The mechanical properties of aluminium alloys are strongly influenced by the alloying elements and their concentration. In the case of aluminium alloy EN AW-6060 the main alloying elements are magnesium and silicon. The first goal of this thesis was to determine stability, repeatability and sensitivity as figures of merit of the in-situ melt identification technique. In this study the emissions from the laser welding process were monitored with a spectrometer. With the information produced by the spectrometer, quantitative analysis was conducted to determine the figures of merit. The quantitative analysis concentrated on magnesium and aluminium emissions and their relation. The results showed that the stability of absolute intensities was low, but the normalized magnesium emissions were quite stable. The repeatability of monitoring magnesium emissions was high (about 90 %). Sensitivity of the in-situ melt identification technique was also high. As small as 0.5 % change in magnesium content was detected by the spectrometer. The second goal of this study was to determine the loss of mass during deep penetration laser welding. The amount of magnesium in the material was measured before and after laser welding to determine the loss of magnesium. This study was conducted for aluminium alloy with nominal magnesium content of 0-10 % and for standard material EN AW-6060 that was welded with filler wire AlMg5. It was found that while the magnesium concentration in the material changed, the loss of magnesium remained fairly even. Also by feeding filler wire, the behaviour was similar. Thirdly, the reason why silicon had not been detected in the emission spectrum needed to be explained. Literature research showed that the amount of energy required for silicon to excite is considerably higher compared to magnesium. The energy input in the used welding process is insufficient to excite the silicon atoms.

The Productivity, Economy and Quality of Welding in the Different Geographical Areas of China - Today and in the Future

This master’s thesis gives out the real situation of the China welding industry and factories nowadays in different geographical areas, in order to inform the Finnish companies who have the willing to find a Chinese welding subcontractor a proper and correct selection concept by analyzing and supplying the information of different scale and form welding factories in different Chinese areas. The first section of this thesis gives out the general situation about the co-operation between China and Finland in the welding industry, also includes the general introduction of the Chinese welding industry. The second section gives out the geographical compartmentalization result of Chinese welding industry, which is where and how many areas will be studied in this thesis. The main body of this thesis is the real information of welding productivity, welding cost, and welding quality in China. All the information was collected from real factories in China by the author. The last section of this thesis is the improvements to the Chinese welding factories that have the willing to become a subcontractor, and the suggestions to the Finnish companies who may find a Chinese welding factory as their subcontractor in future.

Automated Software Testing in Machine Automation

The problem of software (SW) defaults is becoming more and more topical because of increasing amount of the SW and its complication. The majority of these defaults are founded during the test part that consumes about 40-50% of the development efforts. Test automation allows reducing the cost of this process and increasing testing effectiveness. In the middle of 1980 the first tools for automated testing appeared and the automated process was implemented in different kinds of SW testing. In short time, it became obviously, automated testing can cause many problems such as increasing product cost, decreasing reliability and even project fail. This thesis describes automated testing process, its concept, lists main problems, and gives an algorithm for automated test tools selection. Also this work presents an overview of the main automated test tools for embedded systems.

Automation Concept for Electrically Excited LV Synchronous Motor: Implementation into AC500 Programmable Logic Environment

This bachelor’s thesis is a part of the research project realized in the summer 2011 in Lappeenranta University of Technology. The goal of the project was to develop an automation concept for controlling the electrically excited synchronous motor. Thesis concentrates on the implementation of the automation concept into the ABB’s AC500 programmable logic enviroment. The automation program was developed as a state machine with the ABB’s PS501 Control Builder software. For controlling the automation program is developed a fieldbus control and with CodeSys Visualization Tool a local control with control panel. The fieldbus control is done to correspond the ABB drives communication profile and the local control is implemented with a function block which feeds right control words into the statemachine. A field current control of the synchronous motor is realized as a method presented in doctoral thesis of Olli Pyrhönen (Pyrhönen 1998). The Method combines stator flux and torque based openloop control and power factor based feedback control.

Externally excited synchronous machine: Testing the automation concept

This bachelor’s thesis is a part of the research project realized in the summer 2011 in Lappeenranta University of Technology. The goal of the project was to develop an automation concept for controlling the externally excited synchronous motor. Thesis concentrates on the testing planning and testing the system. Testing plan was made for three sectors: For the PLC program testing, for the communication testing and for the whole system testing. PLC program was tested with white box and destructive methods. Communication testing was done by switching maximum com-munication speed and checked if communication was reliable. Whole system testing included among other things speed and torque controlling. The system was tested with exploratory testing also. This enabled more reliable and broader testing than with systematical testing only.

Automation concept for an electrically excited synchronous motor: Setup and requirements specification

This bachelor’s thesis is a part of the research project realized in the summer 2011 in Lappeenranta University of Technology. The goal of the project was to create an automation concept for controlling an electrically excited synchronous motor. This thesis concentrates on the setup and requirements specification part of the concept. The setup consists of ABB AC500 as the PLC master device, DCS800 as an exciter and ACS800 as a frequency converter. The ACS800 frequency converter uses permanent magnet synchronous machine software to control the stator’s magnetic field, the DC drive handles the excitation and the AC500 PLC master controls the communication and functionality of the system. The requirements specification briefly explains the general over-view of the concept, the use and functionality of the PLC program and the requirements needed for the whole concept and the PLC program to work as intended.

Welding development of crane main girder

Konecranes Corporation manufactures huge steel structures in 16 factories worldwide, in which the environment and quality varies. The company has a desire to achieve the same weld quality in each factory, regardless of the manufacturing place. The main subject of this master’s thesis was to develop the present box girder crane welding process, submerged arc welding and especially the fillet welding. Throughput time and manufacturing costs can be decreased by welding the full penetration fillet weld without a bevel, changing present groove types for more appropriate ones and by achieving the desired weld quality on the first time. Welding experiments of longitudinal fillet welding were made according to the present challenges, which the manufacturing process is facing. In longitudinal fillet welding tests the main focus was to achieve full penetration fillet weld for 6, 8 and 10 millimeters thick web plates with single and twin wire submerged arc welding. Full penetration was achieved with all the material thicknesses, both with single and twin wire submerged arc welding processes. The main problem concerning the weld was undercutting and shape of the weld bead. The question about insufficiency of presently used power sources with twin wire was risen up during testing, due to the thicknesses that require high welding current. Bigger power source is required when box girders are welded nonstop, if twin wire is used. For single wire process the penetration was achieved with significantly less amperage than with twin wire.

Advanced welding technologies used for arctic metal structures

Rapid depletion of easy-to-access fossil fuel, predominantly, oil and gas resources has now necessitated increase in need to develop new oil and gas sources in ever more remote and hostile environments. This is necessary in order to explore more oil and gas resources to meet rapidly rising long-term energy demand in the world, both at present and in the nearest future. Arctic is one of these harsh environments, where enormous oil and gas resources are available, containing about 20% of the world total oil and gas, but the environmental conditions are very harsh and hostile. However, virtually all the facilities required for the exploration and development of this new energy source are constructed with metals as well as their alloys and are predominantly joined together by welding processes and technologies. Meanwhile, due to entirely different environment from the usual moderate temperate region, conventional welding technologies, common metals and their alloys cannot be applied as this Arctic environment demand metals structures with very high toughness and strength properties under extremely low temperature. This is due to the fact that metals transit from ductility to brittleness as the temperature moves toward extreme negative values. Hence, this research work investigates and presents the advanced welding technologies applicable to Arctic metal structures which can give satisfactory weldments under active Arctic service conditions. .

Benefits and challenges of supply chain finance business process automation : A case study in ING Bank

Supply chain finance, a financial product provided by the bank, has gained increasing attention and popularity over the last few years. Supply chain finance helps the corporate clients to optimize their financial flows along the supply chain. One characteristic of supply chain finance is that it aims to provide automated solutions. Therefore, the business process automation of supply chain finance is a very interesting and important topic for study. In this study, the business process automation of supply chain finance within the case organization, ING, is analysed. The purpose is to: (1) Identify the benefits to understand the importance to automate supply chain finance business process; (2) Find out the existing automation degree in the supply chain finance business process within the case bank to see what’s the situation now and how to improve in the future; (3) Discover the challenges in the further automation of supply chain finance business process. Firstly, the study finds out that supply chain finance business process automation can bring many benefits to the bank. Automation can improve productivity by using less time and human labour in the business process, and by providing scalable solutions. Automation can also improve quality of the service by reducing the human errors. Last but not least, automation can improve internal governance by providing enhanced visibility of the business process. Because of these potential benefits, many banks are actively seeking solutions to automate their supply chain finance business process. Then, the current automation situation with the case bank is analysed with the help of business process modelling. The supply chain finance business process within the case bank can be further divided into several sub processes: daily transaction, buyer sales and setup, supplier onboarding, contract management, customer services and supports, and contract termination. The study finds out that the daily transaction process is already a highly automated, which is carried out through the web-based trading platform. However, for other business the automation degree is relatively low. Among these business processes, supplier onboarding is most needed for further automation. Then, some solutions are also suggested to automate the supplier onboarding business process. In the end, the study also foresees some challenges during the further automation of supply chain finance business process in the case bank. Some suggestions are also given to deal with these challenges.

A bridge between engineering and language learning : automation and German in an online course

Artikkeli luettavissa osassa: Part 2. - ISBN 9789522163172(PDF). - Liitteenä työpaperi