Simulation of hydrogen peroxide direct synthesis in a microreactor

A set of models in Aspen plus was built to simulate the direct synthesis process of hydrogen peroxide in a micro-reactor system. This process model can be used to carry out material balance calculation under various experimental conditions. Three thermodynamic property methods were compared by calculating gas solubility and Uniquac-RK method was finally selected for process model. Two different operation modes with corresponding operation conditions were proposed as the starting point of future experiments. Simulations for these two modes were carried out to get the information of material streams. Moreover, some hydrodynamic parameters such as gas/liquid superficial velocity, gas holdup were also calculated with improved process model. These parameters proved the proposed experimental conditions reasonable to some extent. The influence of operation conditions including temperature, pressure and circulation ratio was analyzed for the first operation mode, where pure oxygen was fed into dissolving tank and hydrogen-carbon dioxide mixture was fed into microreactor directly. The preferred operation conditions for the system are low temperature (2°C) and high pressure (30 bar) in dissolving tank. High circulation ratio might be good in the sense that more oxygen could be dissolved and fed into reactor for reactions, but meanwhile hydrodynamics of microreactor should be considered. Furthermore, more operation conditions of reactor gas/liquid feeds in both of two operation modes were proposed to provide guidance for future experiment design and corresponding hydrodynamic parameters were also calculated. Finally, safety issue was considered from thermodynamic point of view and there is no explosion danger at given experimental plan since the released reaction heat will not cause solvent vaporization inside the microchannels. The improvement of process model still needs further study based on the future experimental results.

Determinants of cash holdings in Finnish industrial sector: measuring the impact of financial crisis 2007- 2010

This thesis studies cash and short term investments to net assets ratio of Finnish industrial companies during financial crisis, and how different firm specific and macro economical variables affect cash and short term investments. The data consists of quarter level interim reports. Regression analysis was used to find out the effects of different variables. Regression models were formed based on previous studies on cash holdings. It was found that firms studied held more cash during financial crisis than before it. Cash and short-term investments acted as substitute of net working capital. Leverage had a positive and significant relationship to cash and short term investment ratio. It was also found out that firms have a target cash and short term investments ratio.

Microscopic simulation of pigment coating consolidation

The control of coating layer properties is becoming increasingly important as a result of an emerging demand for novel coated paper-based products and an increasing popularity of new coating application methods. The governing mechanisms of microstructure formation dynamics during consolidation and drying are nevertheless, still poorly understood. Some of the difficulties encountered by experimental methods can be overcome by the utilisation of numerical modelling and simulation-based studies of the consolidation process. The objective of this study was to improve the fundamental understanding of pigment coating consolidation and structure formation mechanisms taking place on the microscopic level. Furthermore, it is aimed to relate the impact of process and suspension properties to the microstructure of the coating layer. A mathematical model based on a modified Stokesian dynamics particle simulation technique was developed and applied in several studies of consolidation-related phenomena. The model includes particle-particle and particle-boundary hydrodynamics, colloidal interactions, Born repulsion, and a steric repulsion model. The Brownian motion and a free surface model were incorporated to enable the specific investigation of consolidation and drying. Filter cake stability was simulated in various particle systems, and subjected to a range of base substrate absorption rates and system temperatures. The stability of the filter cake was primarily affected by the absorption rate and size of particles. Temperature was also shown to have an influence. The consolidation of polydisperse systems, with varying wet coating thicknesses, was studied using imposed pilot trial and model-based drying conditions. The results show that drying methods have a clear influence on the microstructure development, on small particle distributions in the coating layer and also on the mobility of particles during consolidation. It is concluded that colloidal properties can significantly impact coating layer shrinkage as well as the internal solids concentration profile. Visualisations of particle system development in time and comparison of systems at different conditions are useful in illustrating coating layer structure formation mechanisms. The results aid in understanding the underlying mechanisms of pigment coating layer consolidation. Guidance is given regarding the relationship between coating process conditions and internal coating slurry properties and their effects on the microstructure of the coating.

Modeling and Analysis of Noise and Interconnects for On-Chip Communication Link Design

This thesis considers modeling and analysis of noise and interconnects in onchip communication. Besides transistor count and speed, the capabilities of a modern design are often limited by on-chip communication links. These links typically consist of multiple interconnects that run parallel to each other for long distances between functional or memory blocks. Due to the scaling of technology, the interconnects have considerable electrical parasitics that affect their performance, power dissipation and signal integrity. Furthermore, because of electromagnetic coupling, the interconnects in the link need to be considered as an interacting group instead of as isolated signal paths. There is a need for accurate and computationally effective models in the early stages of the chip design process to assess or optimize issues affecting these interconnects. For this purpose, a set of analytical models is developed for on-chip data links in this thesis. First, a model is proposed for modeling crosstalk and intersymbol interference. The model takes into account the effects of inductance, initial states and bit sequences. Intersymbol interference is shown to affect crosstalk voltage and propagation delay depending on bus throughput and the amount of inductance. Next, a model is proposed for the switching current of a coupled bus. The model is combined with an existing model to evaluate power supply noise. The model is then applied to reduce both functional crosstalk and power supply noise caused by a bus as a trade-off with time. The proposed reduction method is shown to be effective in reducing long-range crosstalk noise. The effects of process variation on encoded signaling are then modeled. In encoded signaling, the input signals to a bus are encoded using additional signaling circuitry. The proposed model includes variation in both the signaling circuitry and in the wires to calculate the total delay variation of a bus. The model is applied to study level-encoded dual-rail and 1-of-4 signaling. In addition to regular voltage-mode and encoded voltage-mode signaling, current-mode signaling is a promising technique for global communication. A model for energy dissipation in RLC current-mode signaling is proposed in the thesis. The energy is derived separately for the driver, wire and receiver termination.

Synthesis of percarboxylic acids in microreactor

Percarboxylic acids are commonly used as disinfection and bleaching agents in textile, paper, and fine chemical industries. All of these applications are based on the oxidative potential of these compounds. In spite of high interest in these chemicals, they are unstable and explosive chemicals, which increase the risk of synthesis processes and transportation. Therefore, the safety criteria in the production process should be considered. Microreactors represent a technology that efficiently utilizes safety advantages resulting from small scale. Therefore, microreactor technology was used in the synthesis of peracetic acid and performic acid. These percarboxylic acids were produced at different temperatures, residence times and catalyst i.e. sulfuric acid concentrations. Both synthesis reactions seemed to be rather fast because with performic acid equilibrium was reached in 4 min at 313 K and with peracetic acid in 10 min at 343 K. In addition, the experimental results were used to study the kinetics of the formation of performic acid and peracetic acid. The advantages of the microreactors in this study were the efficient temperature control even in very exothermic reaction and good mixing due to the short diffusion distances. Therefore, reaction rates were determined with high accuracy. Three different models were considered in order to estimate the kinetic parameters such as reaction rate constants and activation energies. From these three models, the laminar flow model with radial velocity distribution gave most precise parameters. However, sulfuric acid creates many drawbacks in this synthesis process. Therefore, a ´´greener´´ way to use heterogeneous catalyst in the synthesis of performic acid in microreactor was studied. The cation exchange resin, Dowex 50 Wx8, presented very high activity and a long life time in this reaction. In the presence of this catalyst, the equilibrium was reached in 120 second at 313 K which indicates a rather fast reaction. In addition, the safety advantages of microreactors were investigated in this study. Four different conventional methods were used. Production of peracetic acid was used as a test case, and the safety of one conventional batch process was compared with an on-site continuous microprocess. It was found that the conventional methods for the analysis of process safety might not be reliable and adequate for radically novel technology, such as microreactors. This is understandable because the conventional methods are partly based on experience, which is very limited in connection with totally novel technology. Therefore, one checklist-based method was developed to study the safety of intensified and novel processes at the early stage of process development. The checklist was formulated using the concept of layers of protection for a chemical process. The traditional and three intensified processes of hydrogen peroxide synthesis were selected as test cases. With these real cases, it was shown that several positive and negative effects on safety can be detected in process intensification. The general claim that safety is always improved by process intensification was questioned.

Testate amoebae (thecamoebians) as indicators of aquatic mine impact

The environmental impacts of a single mine often remain local, but acidic and metal-rich acid mine drainage (AMD) from the waste materials may pose a serious threat to adjacent surface waters and their ecosystems. Testate amoebae (thecamoebian) analysis was used together with lake sediment geochemistry to study and evaluate the ecological effects of sulphidic metal mines on aquatic environments. Three different mines were included in the study: Luikonlahti Cu-mine in Kaavi, eastern Finland, Haveri Cu-Au mine in Ylöjärvi, southern Finland and Pyhäsalmi Zn-Cu-S mine in Pyhäjärvi, central Finland. Luikonlahti and Haveri are closed mines, but Pyhäsalmi is still operating. The sampling strategy was case specific, and planned to provide a representative sediment sample series to define natural background conditions, to detect spatial and temporal variations in mine impacts, to evaluate the possible recovery after the peak contamination, and to distinguish the effects of other environmental factors from the mining impacts. In the Haveri case, diatom analyses were performed alongside thecamoebian analysis to evaluate the similarities and differences between the two proxies. The results of the analyses were investigated with multivariate methods (direct and indirect ordinations, diversity and distance measure indices). Finally, the results of each case study were harmonized, pooled, and jointly analyzed to summarize the results for this dissertation. Geochemical results showed broadly similar temporal patterns in each case. Concentrations of ions in the pre-disturbance samples defined the natural baseline against which other results were compared. The beginning of the mining activities had only minor impacts on sediment geochemistry, mainly appearing as an increased clastic input into the lakes at Haveri and Pyhäsalmi. The active mining phase was followed by the metallic contamination and, subsequently, by the most recent change towards decreased but still elevated metal concentrations in the sediments. Because of the delay in the oxidation of waste material and formation of AMD, the most intense, but transient metal contamination phase occurred in the post-mining period at Luikonlahti and Haveri. At Pyhäsalmi, the highest metal contamination preceded effluent mitigation actions. Spatial gradients were observed besides the temporal evolution in both the pre-disturbance and mine-impacted samples from Luikonlahti and Pyhäsalmi. The geochemical gradients varied with distance from the main source of contaminants (dispersion and dilution) and with water depth (redox and pH). The spatial extent of the highest metal contamination associated with these mines remained rather limited. At Haveri, the metallic impact was widespread, with the upstream site in another lake basin found to be contaminated. Changes in thecamoebian assemblages corresponded well with the geochemical results. Despite some differences, the general features and ecological responses of the faunal assemblages were rather similar in each lake. Constantly abundant strains of Difflugia oblonga, Difflugia protaeiformis and centropyxids formed the core of these assemblages. Increasing proportions of Cucurbitella tricuspis towards the surface samples were found in all of the cases. The results affirmed the indicator value of some already known indicator forms, but such as C. tricuspis and higher nutrient levels, but also elicited possible new ones such as D. oblonga ‘spinosa’ and clayey substrate, high conductivity and/or alkalinity, D. protaeiformis ‘multicornis’ and pH, water hardness and the amount of clastic material and Centropyxis constricta ‘aerophila’ and high metal and S concentrations. In each case, eutrophication appeared to be the most important environmental factor, masking the effects of other variables. Faunal responses to high metal inputs in sediments remained minor, but were nevertheless detectable. Besides the trophic state of the lake, numerical methods suggested overall geochemical conditions (pH, redox) to be the most important factor at Luikonlahti, whereas the Haveri results showed the clearest connection between metals and amoebae. At Pyhäsalmi, the strongest relationships were found between Ca- and S-rich present loading, redox conditions and substrate composition. Sediment geochemistry and testate amoeba analysis proved to be a suitable combination of methods to detect and describe the aquatic mine impacts in each specific case, to evaluate recovery and to differentiate between the effects of different anthropogenic and natural environmental factors. It was also suggested that aquatic mine impacts can be significantly mitigated by careful design and after-care of the waste facilities, especially by reducing and preventing AMD. The case-specific approach is nevertheless necessary because of the unique characteristics of each mine and variations in the environmental background conditions.

Software Development Process Modeling. Developers Perspective to Contemporary Modeling Techniques

Formal software development processes and well-defined development methodologies are nowadays seen as the definite way to produce high-quality software within time-limits and budgets. The variety of such high-level methodologies is huge ranging from rigorous process frameworks like CMMI and RUP to more lightweight agile methodologies. The need for managing this variety and the fact that practically every software development organization has its own unique set of development processes and methods have created a profession of software process engineers. Different kinds of informal and formal software process modeling languages are essential tools for process engineers. These are used to define processes in a way which allows easy management of processes, for example process dissemination, process tailoring and process enactment. The process modeling languages are usually used as a tool for process engineering where the main focus is on the processes themselves. This dissertation has a different emphasis. The dissertation analyses modern software development process modeling from the software developers’ point of view. The goal of the dissertation is to investigate whether the software process modeling and the software process models aid software developers in their day-to-day work and what are the main mechanisms for this. The focus of the work is on the Software Process Engineering Metamodel (SPEM) framework which is currently one of the most influential process modeling notations in software engineering. The research theme is elaborated through six scientific articles which represent the dissertation research done with process modeling during an approximately five year period. The research follows the classical engineering research discipline where the current situation is analyzed, a potentially better solution is developed and finally its implications are analyzed. The research applies a variety of different research techniques ranging from literature surveys to qualitative studies done amongst software practitioners. The key finding of the dissertation is that software process modeling notations and techniques are usually developed in process engineering terms. As a consequence the connection between the process models and actual development work is loose. In addition, the modeling standards like SPEM are partially incomplete when it comes to pragmatic process modeling needs, like light-weight modeling and combining pre-defined process components. This leads to a situation, where the full potential of process modeling techniques for aiding the daily development activities can not be achieved. Despite these difficulties the dissertation shows that it is possible to use modeling standards like SPEM to aid software developers in their work. The dissertation presents a light-weight modeling technique, which software development teams can use to quickly analyze their work practices in a more objective manner. The dissertation also shows how process modeling can be used to more easily compare different software development situations and to analyze their differences in a systematic way. Models also help to share this knowledge with others. A qualitative study done amongst Finnish software practitioners verifies the conclusions of other studies in the dissertation. Although processes and development methodologies are seen as an essential part of software development, the process modeling techniques are rarely used during the daily development work. However, the potential of these techniques intrigues the practitioners. As a conclusion the dissertation shows that process modeling techniques, most commonly used as tools for process engineers, can also be used as tools for organizing the daily software development work. This work presents theoretical solutions for bringing the process modeling closer to the ground-level software development activities. These theories are proven feasible by presenting several case studies where the modeling techniques are used e.g. to find differences in the work methods of the members of a software team and to share the process knowledge to a wider audience.

Situational awareness concept in a multinational collaboration environment : challenges in the information sharing framework

Technological capabilities are built to support different types of collaboration, and this gives the justification to widely observe, how activity environments are influenced by technology. Technology as an enabler can be addressed from different perspectives, other than merely technological. Dynamic, evolving environment is at the same time interesting but also challenging. As a multinational collaboration environment, the maritime surveillance is an good example of time critical and evolving environment, where technological solutions enable new ways of collaboration. Justification for the inspiration to use maritime environment as the baseline for understanding the challenges in creating and maintaining adequate level of situational awareness, derives from the complexity of the collaboration and information sharing environment elements, needed to be taken into account, when analyzing criticalities related to decision making. Situational awareness is an important element supporting decision making, and challenges related to it can also be observed in the maritime environment. This dissertation describes the structures and factors involved in this complex setting, found from the case studies that should be taken into account when trying to understand, how these elements affect the activities. This dissertation focuses on the gray area that is between a life threatening situation and normal everyday activities. From the multinational experimentation series case studies, MNE5 and MNE6 it was possible to observe situations that were not life threatening for the participants themselves, but not also basic every day activities. These case studies provided a unique possibility to see situations, where gaining of situational awareness and decision making are challenged with time critical crisis situations. Unfortunately organizations do not normally take the benefit from the everyday work to prepare themselves for possible emerging crisis situations. This dissertation focuses on creating a conceptual model and a concept that supports organizations – also outside the maritime community – to improve their ability to support gaining of situational awareness from the individual training level, all the way to changes in organizational structures in aiming for better support for decision making from the individual level to the highest decision making level. Quick changes and unpredictability are reality in organizations and organizations do not have the possibility to control all the factors that affect their functioning. Since we cannot be prepared for everything, and predict every crisis, individual activities inside teams and as a part of organizations, need to be supported with guidance, tools and training in order to support acting in challenging situations. In fact the ideology of the conceptual model created, lies especially in the aim of not controlling everything in beforehand, but supporting organizations with concrete procedures to help individuals to react in different, unpredictable situations, instead of focusing on traditional risk prevention and management. Technological capabilities are not automatically solutions for functional challenges; this is why it is justified to broaden the problem area observation from the technological perspective. This dissertation demonstrates that it is possible to support collaboration in a multinational environment with technological solutions, but it requires the recognition of technological limitations and accepting the possible restrictions related to technological innovations. Technology should not be considered value per se, the value of technology should be defined according to the support of activities, including strategic and operational environment evaluation, identification of organizational elements, and taking into account also the social factors and their challenges. Then we are one step closer to providing technological solutions that support the actual activities by taking into account the variables of the activity environment in question. The multidisciplinary view to approach the information sharing and collaboration framework, is derived especially from the complexity of decision making and building of situational awareness, since they are not build or created in vacuity, but in the organizational framework by the people doing it with the technological capabilities, enabled by the organizational structures. Introduced case studies were related to maritime environment, but according to the research results, it is valid to argue, that based on the lessons learned it is possible to create and further develop conceptual model and to create a general concept to support a wider range of organizations in their attempt to gain better level of situational awareness (SA) and to support decision making. To proof the versatile usage of the developed concept, I have introduced the case study findings to the health care environment and reflected the identified elements from the trauma center to the created concept. The main contribution to complete this adventure is the presented situational awareness concept created in the respect to NATO concept structure. This has been done to tackle the challenge of collaboration by focusing on situational awareness in the information sharing context by providing a theoretical ground and understanding, of how these issues should be approached, and how these elements can be generalized and used to support activities in other environments as well. This dissertation research has been a several year evolving process reflecting and affecting presented case studies and this learning experience from the case studies has also affected the goals and research questions of this dissertation. This venture has been written from a retro perspective according to ideology of process modeling and design rationale to present to the reader how this entire journey took place and what where the critical milestones that affected the end result, conceptual model. Support in a challenging information sharing framework can be provided with the right type of combination of tools, procedures and individual effort. This dissertation will provide insights to those with a new approach to war technology for the organizations to gain a better level of awareness and to improve the capabilities in decision making. This dissertation will present, from the war technology starting point, a new approach and possibility for the organizations to create a better level of awareness and support for decision making with the right combination of tools, procedures and individual effort.

Tiedonkeruujärjestelmän kehittäminen voimalaitoksen toiminnan tehostamisessa

Diplomityössä kehitetään tiedonkeruujärjestelmää voimalaitoksen toiminnan tehostamiseksi. Aihetta käsitellään tiedonkeruujärjestelmän käyttäjän ja ylläpitäjän näkökulmasta. Tiedonkeruujärjestelmällä kerätään prosessitietoa automaatiojärjestelmästä ja tallennetaan prosessitieto tietokantaan. Työssä on kuvattu sekä automaatio- että tiedonkeruujärjestelmää prosessitiedon keruun, tallentamisen ja hallinnan ymmärtämiseksi. Prosessitiedon merkitystä voimalaitoksen toiminnan kannalta on myös pohdittu. Diplomityö tehtiin Mertaniemen voimalaitoksella, jossa käytännön kehityskohteina olivat laskenta- ja raportointisovellukset. Lisäksi tarkistettiin tietokantamuuttujia. Tiedonkeruujärjestelmää kehitetään ja päivitetään voimalaitoksen laitteisto- ja toimintamuutosten takia. Kehityksellä pyritään tarjoamaan oikeampaa ja luotettavampaa tietoa, korjaamaan virheitä sekä kartoittamaan mahdollisia puutteita.

T&k-toiminnan suorituskyvyn johtaminen: kontekstin vaikutus mittaamiseen pk-yrityksissä

Tutkimuksen päätavoitteena oli ymmärtää, kuinka konteksti vaikuttaa t&k-toiminnan suorituskyvyn mittaamiseen pk-yrityksissä. Tutkimus kartoitti ja kuvaili kontekstin vaikutusta mallilla, joka jaottelee mittaamisen sisältöön, kontekstiin ja prosessiin. Kontekstin vaikutusta sisältöön ja prosessiin tutkittiin sekä suoraan että välillisesti mittaamisen tavoitteen kautta. Tutkimuksessa käytettiin case survey-tutkimusmenetelmää, jossa yhdistyy survey-tutkimuksen ja tapaustutkimuksen strategiat. Empiirisenä aineistona käytettiin olemassa olevia tapaustutkimuksia, joiden laadulliset havainnot muunnettiin systemaattisesti määrällisiksi muuttujiksi koodausjärjestelmällä. Muuttujien yhteyksien ristiintaulukoinnit analysoitiin tilastollisesti merkitsevien riippuvuuksien tunnistamiseksi ja laajempaa joukkoa koskevien päätelmien johtamiseksi. Tulokset olivat yhteneväisiä aiemman tutkimustiedon kanssa, mikä osoittaa kontekstin vaikutuksen t&k-toiminnan suorituskyvyn mittaamiseen olevan samankaltainen pk-yrityksissä kuin suuremmissakin yrityksissä. Empiirisinä yleistyksinä tunnistettiin uusia riippuvuuksia kontekstin ja sisällön sekä kontekstin ja prosessin välillä. Yleistykset suositellaan testattavaksi hypoteeseina jatkotutkimuksessa.

Modeling of residual stresses and distortion due to welding in fillet welds

Welding has a growing role in modern world manufacturing. Welding joints are extensively used from pipes to aerospace industries. Prediction of welding residual stresses and distortions is necessary for accurate evaluation of fillet welds in relation to design and safety conditions. Residual stresses may be beneficial or detrimental, depending whether they are tensile or compressive and the loading. They directly affect the fatigue life of the weld by impacting crack growth rate. Beside theoretical background of residual stresses this study calculates residual stresses and deformations due to localized heating by welding process and subsequent rapid cooling in fillet welds. Validated methods are required for this purpose due to complexity of process, localized heating, temperature dependence of material properties and heat source. In this research both empirical and simulation methods were used for the analysis of welded joints. Finite element simulation has become a popular tool of prediction of welding residual stresses and distortion. Three different cases with and without preload have been modeled during this study. Thermal heat load set is used by calculating heat flux from the given heat input energy. First the linear and then nonlinear material behavior model is modeled for calculation of residual stresses. Experimental work is done to calculate the stresses empirically. The results from both the methods are compared to check their reliability. Residual stresses can have a significant effect on fatigue performance of the welded joints made of high strength steel. Both initial residual stress state and subsequent residual stress relaxation need to be considered for accurate description of fatigue behavior. Tensile residual stresses are detrimental and will reduce the fatigue life and compressive residual stresses will increase it. The residual stresses follow the yield strength of base or filler material and the components made of high strength steel are typically thin, where the role of distortion is emphasizing.

Reusing repository data: migration of data between repositories

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Characteristics of urban heat island (UHI) in a high latitude coastal city - a case study of Turku, SW Finland

The term urban heat island (UHI) refers to the common situation in which the city is warmer than its rural surroundings. In this dissertation, the local climate, and especially the UHI, of the coastal city of Turku (182,000 inh.), SW Finland, was studied in different spatial and temporal scales. The crucial aim was to sort out the urban, topographical and water body impact on temperatures at different seasons and times of the day. In addition, the impact of weather on spatiotemporal temperature differences was studied. The relative importance of environmental factors was estimated with different modelling approaches and a large number of explanatory variables with various spatial scales. The city centre is the warmest place in the Turku area. Temperature excess relative to the coldest sites, i.e. rural areas about 10 kilometers to the NE from the centre, is on average 2 °C. Occasionally, the UHI intensity can be even 10 °C. The UHI does not prevail continuously in the Turku area, but occasionally the city centre can be colder than its surroundings. Then the term urban cool island or urban cold island (UCI) is used. The UCI is most common in daytime in spring and in summer, whereas during winter the UHI prevails throughout the day. On average, the spatial temperature differences are largest in summer, whereas the single extreme values are often observed in winter. The seasonally varying sea temperature causes the shift of relatively warm areas towards the coast in autumn and inland in spring. In the long term, urban land use was concluded to be the most important factor causing spatial temperature differences in the Turku area. The impact was mainly a warming one. The impact of water bodies was emphasised in spring and autumn, when the water temperature was relatively cold and warm, respectively. The impact of topography was on average the weakest, and was seen mainly in proneness of relatively low-lying places for cold air drainage during night-time. During inversions, however, the impact of topography was emphasised, occasionally outperforming those of urban land use and water bodies.

Concentration of hydrogen peroxide and improving its energy efficiency

Distillation is a unit operation of process industry, which is used to separate a liquid mixture into two or more products and to concentrate liquid mixtures. A drawback of the distillation is its high energy consumption. An increase in energy and raw material prices has led to seeking ways to improve the energy efficiency of distillation. In this Master's Thesis, these ways are studied in connection with the concentration of hydrogen peroxide at the Solvay Voikkaa Plant. The aim of this thesis is to improve the energy efficiency of the concentration of the Voikkaa Plant. The work includes a review of hydrogen peroxide and its manufacturing. In addition, the fundamentals of distillation and its energy efficiency are reviewed. An energy analysis of the concentration unit of Solvay Voikkaa Plant is presented in the process development study part. It consists of the current and past information of energy and utility consumptions, balances, and costs. After that, the potential ways to improve the energy efficiency of the distillation unit at the factory are considered and their feasibility is evaluated technically and economically. Finally, proposals to improve the energy efficiency are suggested. Advanced process control, heat integration and energy efficient equipment are the most potential ways to carry out the energy efficient improvements of the concentration at the Solvay Voikkaa factory. Optimization of the reflux flow and the temperatures of the overhead condensers can offer immediate savings in the energy and utility costs without investments. Replacing the steam ejector system with a vacuum pump would result in savings of tens of thousands of euros per year. The heat pump solutions, such as utilizing a mechanical vapor recompression or thermal vapor recompression, are not feasible due to the high investment costs and long pay back times.

Successful IFRS standard change implementation process after the initial IFRS implementation

The main objective of the study was to form a strategic process model and project management tool to help IFRS change implementation projects in the future. These research results were designed based on the theoretical framework of Total Quality Management and leaning on the facts that were collected during the empirical case study of IAS 17 change. The us-age of the process oriented approach in IFRS standard change implementation after the initial IFRS implementation is rationalized with the following arguments: 1) well designed process tools lead to optimization of resources 2) With the help of process stages and related tasks it is easy to ensure the efficient way of working and managing the project as well as make sure to include all necessary stakeholders to the change process. This research is following the qualitative approach and the analysis is in describing format. The first part of the study is a literature review and the latter part has been conducted as a case study. The data has been col-lected in the case company with interviews and observation. The main findings are a process model for IFRS standard change process and a check-list formatted management tool for up-coming IFRS standard change projects. The process flow follows the main cornerstones in IASB’s standard setting process and the management tool has been divided to stages accordingly.