Elemental analysis of wood materials by external millibeam thick target PIXE

PIXE (Particle Induce X-ray Emission spectrometry) was used for analysing stem bark and stem wood of Scots pine, Norway spruce and Silver birch. Thick samples were irradiated, in laboratory atmosphere, with 3 MeV protons and the beam current was measured indirectly using a photo multiplicator (PM) tube. Both point scans and bulk analyses were performed with the 1 mm diameter proton beam. In bulk analyses, whole bark and sectors of discs of the stem wood were dry ashed at 550 ˚C. The ashes were homogenised by shaking and prepared to target pellets for PIXE analyses. This procedure generated representative samples to be analysed, but the enrichment also enabled quantification of some additional trace elements. The ash contents obtained as a product of the sample preparation procedure also showed to be of great importance in the evaluation of results in environmental studies. Spot scans from the pith of pine wood outwards, showed clearly highest concentrations of manganese, calcium and zinc in the first spot irradiated, or 2-3 times higher than in the surrounding wood. For stem wood from the crown part of a pine this higher concentration level was found in the first four spots/mms, including the pith and the two following growth rings. Zinc showed increasing concentrations outwards in sapwood of the pine stem, with the over-all lowest concentrations in the inner half of the sapwood. This could indicate emigration of this element from sapwood being under transformation to heartwood. Point scans across sapwood of pine and spruce showed more distinct variations in concentrations relative to hearth wood. Higher concentrations of e.g. zinc, calcium and manganese were found in earlywood than in denser latewood. Very high concentrations of iron and copper were also seen for some earlywood increments. The ash content of stem bark is up to and order higher than for the stem wood. However, when the elemental concentration in ashes of bark and wood of the same disc were compared, these are very similar – this when trees are growing at spots with no anthropogenic contamination from the atmosphere. The largest difference was obtained for calcium which appeared at two times high concentrations in ashes of bark than in ashes of the wood (ratio of 2). Pine bark is often used in monitoring of atmospheric pollution, where concentrations in bark samples are compared. Here an alternative approach is suggested: Bark and the underlying stem wood of a pine trees are dry ashed and analysed. The elemental concentration in the bark ash is then compared to the concentration of the same element in the wood ash. Comparing bark to wood includes a normalisation for the varying availability of an element from the soil at different sites. When this comparison is done for the ashes of the materials, a normalisation is also obtained for the general and locally different enrichment of inorganic elements from wood to bark. Already a ratio >2 between the concentration in the bark ash and the concentration in the wood ash could indicate atmospheric pollution. For monitoring where bark is used, this way of “inwards” comparison is suggested - instead of comparing to results from analyses of bark from other trees (read reference areas), growing at sites with different soil and, locally, different climate conditions. This approach also enables evaluation of atmospheric pollution from sampling of only relative few individual trees –preferable during forest felling.

Biokaasu-, bioetanoli- ja yhdistelmäprosessin energia- ja hiilidioksiditase vertailu

Biojäte soveltuu erinomaisesti biokaasuprosessin raaka-aineeksi sisältämänsä runsaan or-gaanisen aineksen vuoksi. Bioetanoliprosessin raaka-aineeksi se soveltuu, koska biojäte sisäl-tää runsaasti tärkkelystä sekä selluloosaa. Tässä työssä tutkittiin laskennallisesti bioetanoli-, biokaasu- sekä näiden yhdistelmäprosessin energia- ja hiilidioksiditaseita kirjallisuuden tietoihin pohjautuen. Biokaasuprosessista lopputuotteena saatavan biometaanin käyttäminen bensiiniä korvaavana liikennepolttoaineena tuottaa jo pelkästään palamistuotteena syntyvän hiilidioksidin säästöinä 62 kg/tbiojätettä. Energian suhteen biokaasuprosessi on selvästi yliomavaraisin kaikista kolmesta prosessista, vaikka energiankulutukseen huomioidaan myös jalostuksen tarvitsema sähkönku-lutus. Biokaasuprosessissa oma käyttö on alle 20 % lopputuotteen lämpöarvosta, yhdistelmä-prosessin osalta luku on 4 %-yks alhaisempi.

Liikennebiokaasun tuotannon ja käytön ulkoiset kustannukset Pohjois-Karjalassa

Työn tavoitteena oli selvittää liikennebiokaasuntuotannon ja käytön vaikutus liikenteen ulkoi-siin kustannuksiin Pohjois-Karjalassa. Biokaasua tuotetaan Joensuussa Kuhasalon jäteveden-puhdistamolla sekä Kontiosuon jäteasemalla, Kiteellä biokaasua tuotetaan BioKympin yh-teismädätyslaitoksessa. Lisäksi laskennassa huomioitiin yhden maatilakokoluokan biokaasun-tuotanto. Työssä selvitettiin kaksi skenaariota liikennebiokaasun tuotantomääräksi vuodelle 2015. Liikennebiokaasua voitaisiin tuottaa optimiskenaarion mukaan 3 426 MWh ja maksimi-tuotantoskenaarion mukaan 21 532 MWh. Liikennebiokaasun käytön vaikutukset liikenteen päästöihin laskettiin vuodelle 2015 ja vuo-delle 2020, jolloin liikennebiokaasua käytettäisiin 10 % liikenteen energiantarpeesta Pohjois-Karjalassa. Hiilidioksidipäästöt vähenevät vuoden 2020 tilanteessa samassa suhteessa kuin liikennebiokaasu korvaa fossiilisia polttoaineita. Muista päästöistä merkittävimmät päästövä-hennykset saatiin kun vuoden 2010 dieselautot muutettaisiin biokaasuautoiksi, tällöin hiuk-kaspäästöt alenisivat jopa 18 % vuoden 2010 päästöistä. Lisäksi selvitettiin liikenteen päästöjen pienenemisen vaikutus liikenteen aiheuttamiin ulkoisiin kustannuksiin. Laskettavat ulkoiset kustannukset olivat ilmastonmuutos, pakokaasupäästöt sekä energiariippuvuus. Pakokaasupäästöjen aiheuttamat ulkoiset kustannukset olivat vuonna 2010 noin 7 miljoonaa euroa. Liikennebiokaasua käyttävästä ajoneuvotyypistä riippuen ulkoiset kustannukset laskevat vuoden 2020 tilanteessa 10–16 % vuoden 2010 kustannuksista. Ilmastonmuutoksen ulkoiset kustannukset vuodelle 2010 olivat 9,5 miljoonaa euroa. Biokaasun käytön avulla kustannuksissa voitaisiin säästää 910 000 euroa vuonna 2020. Ener-giariippuvuuden hinta öljynkäytöstä oli vuonna 2010 noin 4,2 miljoonaa euroa ja vuonna 2020 kustannukset voisivat laskea 450 000 euroa.

Modelling of calciner in post-combustion carbon capture process

Climate change has given an impetus to research and developed new technologies to reduce significantly carbon dioxide emissions in energy production in the developed countries. The major pollution source, fossil fuels, will be used as an energy source for many decades, which provides the demand for carbon capture and storage technologies. Over recent years many new technologies has been developed and one of the most promising is calcium-looping in post-combustion carbon capture process, which use carbonation-calcination cycle to capture carbon dioxide from the flue gas of a combustion process. First pilot plant for calcium-looping process has been built in Oviedo, Spain. In this study, a three-dimensional model has been created for the calciner, which is one of the two fluidized bed reactors needed for the process. The calciner is a regenerator where the captured carbon dioxide is removed from the calcium material and then collected after the reactor. Thesis concentrates in creating the calciner 3D-model frame with CFB3D-program and testing the model with two different example cases. Used input parameters and calciner geometry are Oviedo pilot plant design parameters. The calculation results give information about the process and show that pilot plant calciner should perform as planned. This Master’s Thesis is done in participation to EU FP7 project CaOling.

The probabilistic risk analysis of external hazards of an interim storage for spent nuclear fuel

Tässä diplomityössä tehtiin Olkiluodon ydinvoimalaitoksella sijaitsevan käytetyn ydinpolttoaineen allasvarastointiin perustuvan välivaraston todennäköisyysperustainen ulkoisten uhkien riskianalyysi. Todennäköisyysperustainen riskianalyysi (PRA) on yleisesti käytetty riskien tunnistus- ja lähestymistapa ydinvoimalaitoksella. Työn tarkoituksena oli laatia täysin uusi ulkoisten uhkien PRA-analyysi, koska Suomessa ei ole aiemmin tehty vastaavanlaisia tämän tutkimusalueen riskitarkasteluja. Riskitarkastelun motiivina ovat myös maailmalla tapahtuneiden luonnonkatastrofien vuoksi korostunut ulkoisten uhkien rooli käytetyn ydinpolttoaineen välivarastoinnin turvallisuudessa. PRA analyysin rakenne pohjautui tutkimuksen alussa luotuun metodologiaan. Analyysi perustuu mahdollisten ulkoisten uhkien tunnistamiseen pois lukien ihmisen aikaansaamat tahalliset vahingot. Tunnistettujen ulkoisten uhkien esiintymistaajuuksien ja vahingoittamispotentiaalin perusteella ulkoiset uhat joko karsittiin pois tutkimuksessa määriteltyjen karsintakriteerien avulla tai analysoitiin tarkemmin. Tutkimustulosten perusteella voitiin todeta, että tiedot hyvin harvoin tapahtuvista ulkoisista uhista ovat epätäydellisiä. Suurinta osaa näistä hyvin harvoin tapahtuvista ulkoisista uhista ei ole koskaan esiintynyt eikä todennäköisesti koskaan tule esiintymään Olkiluodon vaikutusalueella tai edes Suomessa. Esimerkiksi salaman iskujen ja öljyaltistuksen roolit ja vaikutukset erilaisten komponenttien käytettävyyteen ovat epävarmasti tunnettuja. Tutkimuksen tuloksia voidaan pitää kokonaisuudessaan merkittävinä, koska niiden perusteella voidaan osoittaa ne ulkoiset uhat, joiden vaikutuksia olisi syytä tutkia tarkemmin. Yksityiskohtaisempi tietoisuus hyvin harvoin esiintyvistä ulkoisista uhista tarkentaisi alkutapahtumataajuuksien estimaatteja.

On Innovative Search: the use of internal and external sources of innovation among Finnish innovators

This dissertation explores the use of internal and external sources of knowledge in modern innovation processes. It builds on a framework that combines theories such as a behavioural theory of the firm, the evolutionary theory of economic change, and modern approaches to strategic management. It follows the recent increase in innovation research focusing on the firm-level examination of innovative activities instead of traditional industry-level determinants. The innovation process is seen as a problem- and slack- driven search process, which can take several directions in terms of organizational boundaries in the pursuit of new knowledge and other resources. It thus draws on recent models of technological change, according to which firms nowadays should build their innovative activities on both internal and external sources of innovation rather than relying solely on internal resources. Four different research questions are addressed, all of which are empirically investigated via a rich dataset covering Finnish innovators collected by Statistics Finland. Firstly, the study examines how the nature of problems shapes the direction of any search for new knowledge. In general it demonstrates that the nature of the problem does affect the direction of the search, although under resource constraints firms tend to use external rather than internal sources of knowledge. At the same time, it shows that those firms that are constrained in terms of finance seem to search both internally and externally. Secondly, the dissertation investigates the relationships between different kinds of internal and external sources of knowledge in an attempt to find out where firms should direct their search in order to exploit the potential of a distributed innovation process. The concept of complementarities is applied in this context. The third research question concerns how the use of external knowledge sources – openness to external knowledge – influences the financial performance of firms. Given the many advantages of openness presented in the current literature, the focus is on how it shapes profitability. The results reveal a curvilinear relationship between profitability and openness (taking an inverted U-shape), the implication being that it pays to be open up to a certain point, but being too open to external sources may be detrimental to financial performance. Finally, the dissertation addresses some challenges in CISbased innovation research that have received relatively little attention in prior studies. The general aim is to underline the fact that comprehensive understanding of the complex process of technological change requires the constant development of methodological approaches (in terms of data and measures, for example). All the empirical analyses included in the dissertation are based on the Finnish CIS (Finnish Innovation Survey 1998-2000).

Strategic external deployment of intellectual assets

Globalization, pervasiveness of technology and ICT, and the buildup of information societies and policies have lead to a growing abundance of knowledge and highly educated labour supply that is distributed widely. These changes have shifted the foundation of competitiveness to valuable knowledge resources which are now distributed widely across the globe, across actors in the value chain and across educated individuals in multiple organizations. Against this backdrop, the paradigm of open innovation (OI) has emerged as a new response to managing the increased amount of boundary-spanning knowledge flows in and out of the innovation process. The outbound mode of open innovation, that is to say the external exploitation of knowledge assets outside of the firm’s own products and services, has been the less-researched aspect of the concept and so far typically seen as concerning the outlicensing of unused technological assets to generate additional revenue. Given that open innovation is essentially a framework for the holistic structuring and management of crossboundary knowledge flows to improve a firm’s innovative performance, a close integration to corporate strategy seems imperative in order to fully benefit from it. Integrating open innovation to strategy leads to elevating its role from a fringe activity to a central innovation management issue that needs to be systematically managed. Building a structure that allows effective management necessitates linking open innovation activities to each phase of the innovation process. Previously, the connection between outbound OI and the earlier stages of innovation has not been studied. The thesis finds that connecting outbound OI to the entire innovation process of the firm, including the fuzzy front end of innovation, is critical for attaining strategic objectives and to the successful implementation and management of the activity. The practical purpose for the research is to enable companies to fully utilize their potential for outbound open innovation and to be able to implement and manage it from a strategic standpoint.

Surface transformation hardening of carbon steel with high power fiber laser

This study investigated the surface hardening of steels via experimental tests using a multi-kilowatt fiber laser as the laser source. The influence of laser power and laser power density on the hardening effect was investigated. The microhardness analysis of various laser hardened steels was done. A thermodynamic model was developed to evaluate the thermal process of the surface treatment of a wide thin steel plate with a Gaussian laser beam. The effect of laser linear oscillation hardening (LLOS) of steel was examined. An as-rolled ferritic-pearlitic steel and a tempered martensitic steel with 0.37 wt% C content were hardened under various laser power levels and laser power densities. The optimum power density that produced the maximum hardness was found to be dependent on the laser power. The effect of laser power density on the produced hardness was revealed. The surface hardness, hardened depth and required laser power density were compared between the samples. Fiber laser was briefly compared with high power diode laser in hardening medium-carbon steel. Microhardness (HV0.01) test was done on seven different laser hardened steels, including rolled steel, quenched and tempered steel, soft annealed alloyed steel and conventionally through-hardened steel consisting of different carbon and alloy contents. The surface hardness and hardened depth were compared among the samples. The effect of grain size on surface hardness of ferritic-pearlitic steel and pearlitic-cementite steel was evaluated. In-grain indentation was done to measure the hardness of pearlitic and cementite structures. The macrohardness of the base material was found to be related to the microhardness of the softer phase structure. The measured microhardness values were compared with the conventional macrohardness (HV5) results. A thermodynamic model was developed to calculate the temperature cycle, Ac1 and Ac3 boundaries, homogenization time and cooling rate. The equations were numerically solved with an error of less than 10-8. The temperature distributions for various thicknesses were compared under different laser traverse speed. The lag of the was verified by experiments done on six different steels. The calculated thermal cycle and hardened depth were compared with measured data. Correction coefficients were applied to the model for AISI 4340 steel. AISI 4340 steel was hardened by laser linear oscillation hardening (LLOS). Equations were derived to calculate the overlapped width of adjacent tracks and the number of overlapped scans in the center of the scanned track. The effect of oscillation frequency on the hardened depth was investigated by microscopic evaluation and hardness measurement. The homogeneity of hardness and hardened depth with different processing parameters were investigated. The hardness profiles were compared with the results obtained with conventional single-track hardening. LLOS was proved to be well suitable for surface hardening in a relatively large rectangular area with considerable depth of hardening. Compared with conventional single-track scanning, LLOS produced notably smaller hardened depths while at 40 and 100 Hz LLOS resulted in higher hardness within a depth of about 0.6 mm.

Characterisation of Laser Beam and Paper Material Interaction

It is known already from 1970´s that laser beam is suitable for processing paper materials. In this thesis, term paper materials mean all wood-fibre based materials, like dried pulp, copy paper, newspaper, cardboard, corrugated board, tissue paper etc. Accordingly, laser processing in this thesis means all laser treatments resulting material removal, like cutting, partial cutting, marking, creasing, perforation etc. that can be used to process paper materials. Laser technology provides many advantages for processing of paper materials: non-contact method, freedom of processing geometry, reliable technology for non-stop production etc. Especially packaging industry is very promising area for laser processing applications. However, there are only few industrial laser processing applications worldwide even in beginning of 2010´s. One reason for small-scale use of lasers in paper material manufacturing is that there is a shortage of published research and scientific articles. Another problem, restraining the use of laser for processing of paper materials, is colouration of paper material i.e. the yellowish and/or greyish colour of cut edge appearing during cutting or after cutting. These are the main reasons for selecting the topic of this thesis to concern characterization of interaction of laser beam and paper materials. This study was carried out in Laboratory of Laser Processing at Lappeenranta University of Technology (Finland). Laser equipment used in this study was TRUMPF TLF 2700 carbon dioxide laser that produces a beam with wavelength of 10.6 μm with power range of 190-2500 W (laser power on work piece). Study of laser beam and paper material interaction was carried out by treating dried kraft pulp (grammage of 67 g m-2) with different laser power levels, focal plane postion settings and interaction times. Interaction between laser beam and dried kraft pulp was detected with different monitoring devices, i.e. spectrometer, pyrometer and active illumination imaging system. This way it was possible to create an input and output parameter diagram and to study the effects of input and output parameters in this thesis. When interaction phenomena are understood also process development can be carried out and even new innovations developed. Fulfilling the lack of information on interaction phenomena can assist in the way of lasers for wider use of technology in paper making and converting industry. It was concluded in this thesis that interaction of laser beam and paper material has two mechanisms that are dependent on focal plane position range. Assumed interaction mechanism B appears in range of average focal plane position of 3.4 mm and 2.4 mm and assumed interaction mechanism A in range of average focal plane position of 0.4 mm and -0.6 mm both in used experimental set up. Focal plane position 1.4 mm represents midzone of these two mechanisms. Holes during laser beam and paper material interaction are formed gradually: first small hole is formed to interaction area in the centre of laser beam cross-section and after that, as function of interaction time, hole expands, until interaction between laser beam and dried kraft pulp is ended. By the image analysis it can be seen that in beginning of laser beam and dried kraft pulp material interaction small holes off very good quality are formed. It is obvious that black colour and heat affected zone appear as function of interaction time. This reveals that there still are different interaction phases within interaction mechanisms A and B. These interaction phases appear as function of time and also as function of peak intensity of laser beam. Limit peak intensity is the value that divides interaction mechanism A and B from one-phase interaction into dual-phase interaction. So all peak intensity values under limit peak intensity belong to MAOM (interaction mechanism A one-phase mode) or to MBOM (interaction mechanism B onephase mode) and values over that belong to MADM (interaction mechanism A dual-phase mode) or to MBDM (interaction mechanism B dual-phase mode). Decomposition process of cellulose is evolution of hydrocarbons when temperature is between 380- 500°C. This means that long cellulose molecule is split into smaller volatile hydrocarbons in this temperature range. As temperature increases, decomposition process of cellulose molecule changes. In range of 700-900°C, cellulose molecule is mainly decomposed into H2 gas; this is why this range is called evolution of hydrogen. Interaction in this range starts (as in range of MAOM and MBOM), when a small good quality hole is formed. This is due to “direct evaporation” of pulp via decomposition process of evolution of hydrogen. And this can be seen can be seen in spectrometer as high intensity peak of yellow light (in range of 588-589 nm) which refers to temperature of ~1750ºC. Pyrometer does not detect this high intensity peak since it is not able to detect physical phase change from solid kraft pulp to gaseous compounds. As interaction time between laser beam and dried kraft pulp continues, hypothesis is that three auto ignition processes occurs. Auto ignition of substance is the lowest temperature in which it will spontaneously ignite in a normal atmosphere without an external source of ignition, such as a flame or spark. Three auto ignition processes appears in range of MADM and MBDM, namely: 1. temperature of auto ignition of hydrogen atom (H2) is 500ºC, 2. temperature of auto ignition of carbon monoxide molecule (CO) is 609ºC and 3. temperature of auto ignition of carbon atom (C) is 700ºC. These three auto ignition processes leads to formation of plasma plume which has strong emission of radiation in range of visible light. Formation of this plasma plume can be seen as increase of intensity in wavelength range of ~475-652 nm. Pyrometer shows maximum temperature just after this ignition. This plasma plume is assumed to scatter laser beam so that it interacts with larger area of dried kraft pulp than what is actual area of beam cross-section. This assumed scattering reduces also peak intensity. So result shows that assumably scattered light with low peak intensity is interacting with large area of hole edges and due to low peak intensity this interaction happens in low temperature. So interaction between laser beam and dried kraft pulp turns from evolution of hydrogen to evolution of hydrocarbons. This leads to black colour of hole edges.

Carbon Nanotubes as Material for Supercapacitor Electrodes

Electrochemical double-layer supercapacitors have an intermediate position between rechargeable batteries, which can store high amounts of energy, and dielectric capacitors, which have high output power. Supercapacitors are widely suggested to be used in automobiles (recuperation during braking, facilitate engine starting, electric stabilization of the system), industry (forklifts, elevators), hybrid off-road machinery and also in consumer electronics. Supercapacitor electrodes require highly porous material. Typically, activated carbon is used. Specific surface area of activated carbon is approximately 1000 m2 per gram. Carbon nanotubes represent one of prospective materials. According to numerous studies this material allows to improve the properties of supercapacitors. The task of this Master‘s Thesis was to test multiwalled carbon nanotubes and become confident with the testing methods.

Oxidation rates of carbon and nitrogen in char residues from solid fuels

Computational fluid dynamics (CFD) modeling is an important tool in designing new combustion systems. By using CFD modeling, entire combustion systems can be modeled and the emissions and the performance can be predicted. CFD modeling can also be used to develop new and better combustion systems from an economical and environmental point of view. In CFD modeling of solid fuel combustion, the combustible fuel is generally treated as single fuel particles. One of the limitations with the CFD modeling concerns the sub-models describing the combustion of single fuel particles. Available models in the scientific literature are in many cases not suitable as submodels for CFD modeling since they depend on a large number of input parameters and are computationally heavy. In this thesis CFD-applicable models are developed for the combustion of single fuel particles. The single particle models can be used to improve the combustion performance in various combustion devices or develop completely new technologies. The investigated fields are oxidation of carbon (C) and nitrogen (N) in char residues from solid fuels. Modeled char-C oxidation rates are compared to experimental oxidation rates for a large number of pulverized solid fuel chars under relevant combustion conditions. The experiments have been performed in an isothermal plug flow reactor operating at 1123-1673 K and 3-15 vol.% O2. In the single particle model, the char oxidation is based on apparent kinetics and depends on three fuel specific parameters: apparent pre-exponential factor, apparent activation energy, and apparent reaction order. The single particle model can be incorporated as a sub-model into a CFD code. The results show that the modeled char oxidation rates are in good agreement with experimental char oxidation rates up to around 70% of burnout. Moreover, the results show that the activation energy and the reaction order can be assumed to be constant for a large number of bituminous coal chars under conditions limited by the combined effects of chemical kinetics and pore diffusion. Based on this, a new model based on only one fuel specific parameter is developed (Paper III). The results also show that reaction orders of bituminous coal chars and anthracite chars differ under similar conditions (Paper I and Paper II); reaction orders of bituminous coal chars were found to be one, while reaction orders of anthracite chars were determined to be zero. This difference in reaction orders has not previously been observed in the literature and should be considered in future char oxidation models. One of the most frequently used comprehensive char oxidation models could not explain the difference in the reaction orders. In the thesis (Paper II), a modification to the model is suggested in order to explain the difference in reaction orders between anthracite chars and bituminous coal chars. Two single particle models are also developed for the NO formation and reduction during the oxidation of single biomass char particles. In the models the char-N is assumed to be oxidized to NO and the NO is partly reduced inside the particle. The first model (Paper IV) is based on the concentration gradients of NO inside and outside the particle and the second model is simplified to such an extent that it is based on apparent kinetics and can be incorporated as a sub-model into a CFD code (Paper V). Modeled NO release rates from both models were in good agreement with experimental measurements from a single particle reactor of quartz glass operating at 1173-1323 K and 3-19 vol.% O2. In the future, the models can be used to reduce NO emissions in new combustion systems.