Kommunikaatio ja tiedonsiirto etätyössä

Tutkimuksen tavoitteena oli selvittää etätyönteon vaikutuksia kommunikaatioon ja tiedonsiirtoon. Teoriaosuudessa tutkitaan akateemista keskustelua aiemmin mainittujen aiheiden parissa. Tutkimus on laadultaan kvalitatiivinen ja se toteutettiin puolistrukturoiduilla teemahaastatteluilla. Tutkimuksen havainnot noudattivat pitkälti teoriaosuudessa esiin nousseita linjoja, mutta muun muassa inhimillisten tekijöiden merkitys kommunikaatiohalukkuuteen nousi vahvasti esiin. Tämän lisäksi etätyön ajallisella määrällä, etätyönteon sijainnilla sekä yleisellä organisaatiotasoisella suhtautumisella etätyöhön todettiin olevan merkitystä kommunikaation ja siten myös tiedonsiirron laatuun, tiheyteen ja määrään.

Fetal alcohol spectrum disorders in Finnish children and adolescents : diagnosis, cognition, behavior, adaptation and brain metabolic alterations

Alcohol consumption during pregnancy can potentially affect the developing fetus in devastating ways, leading to a range of physical, neurological, and behavioral alterations most accurately termed Fetal Alcohol Spectrum Disorders (FASD). Despite the fact that it is a preventable disorder, prenatal alcohol exposure today constitutes a leading cause of intellectual disability in the Western world. In Western countries where prevalence studies have been performed the rates of FASD exceed, for example, autism spectrum disorders, Down’s syndrome and cerebral palsy. In addition to the direct effects of alcohol, children and adolescents with FASD are often exposed to a double burden in life, as their neurological sequelae are accompanied by adverse living surroundings exposing them to further environmental risk. However, children with FASD today remain remarkably underdiagnosed by the health care system. This thesis forms part of a larger multinational research project, The Collaborative Initiative on Fetal Alcohol Spectrum Disorders (the CIFASD), initiated by the National Institute of Alcohol Abuse and Alcoholism (NIAAA) in the U.S.A. The general aim of the present thesis was to examine a cohort of children and adolescents growing up with fetal alcohol-related damage in Finland. The thesis consists of five studies with a broad focus on diagnosis, cognition, behavior, adaptation and brain metabolic alterations in children and adolescents with FASD. The participants consisted of four different groups: one group with histories of prenatal exposure to alcohol, the FASD group; one IQ matched contrast group mostly consisting of children with specific learning disorder (SLD); and two typically-developing control groups (CON1 and CON2). Participants were identified through medical records, random sampling from the Finnish national population registry and email alerts to students. Importantly, the participants in the present studies comprise a group of very carefully clinically characterized children with FASD as the studies were performed in close collaboration with leading experts in the field (Prof. Edward Riley and Prof. Sarah Mattson, Center for Behavioral Teratology, San Diego State University, U.S.A; Prof. Eugene Hoyme, Sanford School of Medicine, University of South Dakota, U.S.A.). In the present thesis, the revised Institute of Medicine diagnostic criteria for FASD were tested on a Finnish population and found to be a reliable tool for differentiating among the subgroups of FASD. A weighted dysmorphology scoring system proved to be a valuable additional adjunct in quantification of growth deficits and dysmorphic features in children with FASD (Study 1). The purpose of Study 2 was to clarify the relationship between alcohol-related dysmorphic features and general cognitive capacity. Results showed a significant correlation between dysmorphic features and cognitive capacity, suggesting that children with more severe growth deficiency and dysmorphic features have more cognitive limitations. This association was, however, only moderate, indicating that physical markers and cognitive capacity not always go hand in hand in individuals with FASD. Behavioral problems in the FASD group proved substantial compared to the typically developing control group. In Study 3 risk and protective factors associated with behavioral problems in the FASD group were explored further focusing on diagnostic and environmental factors. Two groups with elevated risks for behavioral problems emerged: length of time spent in residential care and a low dysmorphology score proved to be the most pervasive risk factor for behavioral problems. The results underscore the clinical importance of appropriate services and care for less visibly alcohol affected children and highlight the need to attend to children with FASD being raised in institutions. With their background of early biological and psychological impairment compounded with less opportunity for a close and continuous caregiver relationship, such children seem to run an especially great risk of adverse life outcomes. Study 4 focused on adaptive abilities such as communication, daily living skills and social skills, in other words skills that are important for gradually enabling an independent life, maintain social relationships and allow the individual to become integrated into society. The results showed that adaptive abilities of children and adolescents growing up with FASD were significantly compromised compared to both typically-developing peers and IQ-matched children with SLD. Clearly different adaptive profiles were revealed where the FASD group performed worse than the SLD group, who in turn performed worse than the CON1 group. Importantly, the SLD group outperformed the FASD group on adaptive behavior in spite of comparable cognitive levels. This is the first study to compare adaptive abilities in a group of children and adolescents with FASD relative to both a contrast group of IQ-matched children with SLD and to a group of typically-developing peers. Finally, in Study 5, through magnetic resonance spectroscopic imaging (MRS) evidence of longstanding neurochemical alterations were observed in adolescents and young adults with FASD related to alcohol exposure in utero 14-20 years earlier. Neurochemical alterations were seen in several brain areas: in frontal and parietal cortices, corpus callosum, thalamus and frontal white matter areas as well as in the cerebellar dentate nucleus. The findings are compatible with neuropsychological findings in FASD. Glial cells seemed to be more affected than neurons. In conclusion, more societal efforts and resources should be focused on recognizing and diagnosing FASD, and supporting subgroups with elevated risk of poor outcome. Without adequate intervention children and adolescents with FASD run a great risk of marginalization and social maladjustment, costly not only to society but also to the lives of the many young people with FASD.

Syntyykö Suomeen puulaaksoja - Suomen puutuoteteollisuuden pk-yritysten tila ja tulevaisuus

Metsäteollisuus on tullut Suomeen ulkomaisen pääoman ja tietotaidon avulla vajaat kaksisataa vuotta sitten. Se on toiminut melkein koko jatkosodan jälkeisen ajan suojatussa ympäristössä ja ulkomaisesta kilpailusta riippumattomassa toimintaympäristössä. Kuten Porter ja muut ovat todistaneet, tällainen toimintaympäristö ei kehitä kansainvälisesti kilpailukykyistä teollisuutta globaaleilla markkinoilla. Liittyminen Euroopan unioniin ja sittemmin Euroopan rahaliittoon saattoi puunjalostusteollisuuden täysin uudenlaiseen kilpailutilanteeseen. Sama tapahtui myös alan pk-yrityksille, jotka olivat joutuneet toimimaan heikosti kilpailluilla raaka-ainemarkkinoilla. Tutkimus on tulevaisuudentutkimus, jossa tutkimusongelmia lähestytään kolmen teorian avulla. Porterin klusteriteoria tarjoaa mahdollisuuden arvioida metsäteollisuutta sekä kokonaisuutena että toimivana monimuotoisena organisaationa, jossa kustannukset ja hinta muodostuvat arvoketjun toimijoiden osakustannuksista. Bionomiateoria eli darvinistinen talousteoria testaa suomalaisen puunjalostusteollisuuden pk-yritysten kilpailukykyä ja paineita hakeutua edullisemmille toiminta- alueille. Evoluutioteoria tarkastelee sukupolvenvaihdoksen problematiikkaa. Sukupolvenvaihdoksen onnistuminen muodostuu puutoimialan elämän ja kuoleman kysymykseksi. Tämä on etenkin pk-yrityksiä kohtaava ongelma. Asiaa selvitettiin Mauno Rintalan suorittamalla kyselytutkimuksella Puuteollisuusyrittäjien jäsenistön keskuudessa. Ongelma johtuu suurista sodan jälkeen syntyneistä ikäluokista. Nämä vuosina 1945– 50 syntyneet ovat siirtymässä eläkkeelle vuosien 2005 ja 2015 välillä. Kyseisissä ikäluokissa yritystiheys on noin kaksi kertaa suurempi kuin sen jälkeisissä ikäluokissa. Suoritetun kyselyn sekä muiden suomalaisten ja kansainvälisten tutkimusten perusteella näyttää siltä, että eläkkeelle siirryttäessä vain noin 30 %:lla yrityksistä on jatkaja tiedossa suvusta tai lähipiiristä. Tämä merkitsee sitä, että 70 % eläköityvän ikäluokan omistamista yrityksistä poistuu pysyvästi markkinoilta. Suomessa poistuma merkitsee noin 40 % koko yritysvarannosta eli noin 80 000 yritystä. Tilastot toimivien yritysten määrästä ovat kuitenkin hyvin ristiriitaisia, joten todellista määrää on mahdoton arvioida. Noin suuren määrän poistuminen markkinoilta uhkaa jo hyvinvointivaltion perusrakenteita. Tutkimustulos edellyttää nopeita toimenpiteitä teollisten pkyritysten pelastamiseksi ja säilyttämiseksi Suomessa. Sukupolvenvaihdoksen onnistuminen on tässä prosessissa ensiarvoisessa asemassa. Kaikkien edellä mainittujen yritysten poistuminen markkinoilta edellyttäisi noin 400 000 uuden yrityksen perustamista, koska ainoastaan noin 20 % yrityksistä selviää ensimmäiset kolme vuotta. Tutkimukseen perustuen esitetään prosessimalli sukupolvenvaihdoksen suorittamiseksi. Suomen tärkeimmissä kilpailijamaissa valtioiden metsäomistus on määräävässä asemassa. Meillä metsät ovat yksityisessä omistuksessa ja vain pieni osa valtion omistuksessa. Puumarkkinat toimivat markkinatalouden ehdoilla ilman valtion ohjausta. Ongelmaksi on kehittymässä puun saanti. Metsänomistus on sukupolvien myötä hajaantunut hyvin pieniksi metsälöiksi. Nykyiset metsänomistajat asuvat kaupungeissa ja ovat pääosin palkkatyössä. He eivät ole samalla tavoin riippuvaisia puutuloista kuin heidän esi-isänsä. Metsäverotuksen uudistuminen lisää puun saannin epävarmuutta. Se on muuttumassa pinta-alaverotuksesta puun myynnin verotukseen. Puun myynti on vilkasta ennen järjestelmien vaihtumista ja vähäisempää sen jälkeen. Myös näitä ongelmia on pyritty ratkomaan uudenlaisen metsänomistusmallin avulla. Puuteollisuus on hyvin vanha teollisuudenala. Raaka-aine muodostaa määräävän osan kustannuksista. Muutokset ovat hitaita ja todelliset innovaatiot pitkäkestoisia. Uusia innovaatioita tapahtuu harvoin. Kannattavuutta parannetaan tuoteprosessien ja arvoketjujen kehittämisen kautta. Yhteiskunnan osuus alan kehittämisessä ja säilyttämisessä on ratkaiseva. Asioiden moninaisuus tekee tutkimuksen vaikeaksi, mutta sitäkin tärkeämmäksi kansantalouden kannalta. Tällaisissa suurissa murroksissa korostuu kaikkien päättävien tahojen henkinen valmius ja tahto tehdä oikeita ratkaisuja oikeaan aikaan.

Kunnossapito-ohjelman rakentaminen RCM - menetelmän avulla

Työn tarkoituksena oli luoda UPM Kaukaan sellutehtaan kaustisointi- ja meesauunialueelle kunnossapito-ohjelma, RCM eli luotettavuuskeskeinen kunnossapitomenetelmää käyttäen. Tavoitteena oli luoda ennakkohuolto-ohjelma, joka pohjautuu laitekriittisyyksiin sekä optimoida kohdealueen laitteiden varaosien varastointia. Perustaksi työlle luotiin uusi kriittisyysluokittelumalli, joka perustuu PSK 6800 standardiin. Tarvittavien ennakkohuoltotoimenpiteiden määrittämisen apuna käytettiin toimenpiteiden määritysmatriisia. Varaosavaraston optimointia varten luotiin varaosien varastointitarpeen määritysmatriisi. Prosessin suorittamisessa korostui laaja ja osaava projektiryhmä, jonka avulla asioiden läpikäynnissä oli tarvittavat tiedot saatavilla. Projektiryhmässä oli mukana sekä kunnossapidon että käytön henkilöitä. Kunnossapito-ohjelmasta muodostui erittäin kattava. Seisokkia vaativat toimenpiteet ovat aikataulutettu siten, että niitä suoritetaan tasaisesti vuoden aikana. Uusien huoltorivien ansiosta alueen kunnossapito selkeytyy paljon.

Recovery of biomass-derived valuable compounds using chromatographic and membrane separations

Utilization of biomass-based raw materials for the production of chemicals and materials is gaining an increasing interest. Due to the complex nature of biomass, a major challenge in its refining is the development of efficient fractionation and purification processes. Preparative chromatography and membrane filtration are selective, energy-efficient separation techniques which offer a great potential for biorefinery applications. Both of these techniques have been widely studied. On the other hand, only few process concepts that combine the two methods have been presented in the literature. The aim of this thesis was to find the possible synergetic effects provided by combining chromatographic and membrane separations, with a particular interest in biorefinery separation processes. Such knowledge could be used in the development of new, more efficient separation processes for isolating valuable compounds from complex feed solutions that are typical for the biorefinery environment. Separation techniques can be combined in various ways, from simple sequential coupling arrangements to fully-integrated hybrid processes. In this work, different types of combined separation processes as well as conventional chromatographic separation processes were studied for separating small molecules such as sugars and acids from biomass hydrolysates and spent pulping liquors. The combination of chromatographic and membrane separation was found capable of recovering high-purity products from complex solutions. For example, hydroxy acids of black liquor were successfully recovered using a novel multistep process based on ultrafiltration and size-exclusion chromatography. Unlike any other separation process earlier suggested for this challenging separation task, the new process concept does not require acidification pretreatment, and thus it could be more readily integrated into a pulp-mill biorefinery. In addition to the combined separation processes, steady-state recycling chromatography, which has earlier been studied for small-scale separations of high-value compounds only, was found a promising process alternative for biorefinery applications. In comparison to conventional batch chromatography, recycling chromatography provided higher product purity, increased the production rate and reduced the chemical consumption in the separation of monosaccharides from biomass hydrolysates. In addition, a significant further improvement in the process performance was obtained when a membrane filtration unit was integrated with recycling chromatography. In the light of the results of this work, separation processes based on combining membrane and chromatographic separations could be effectively applied for different biorefinery applications. The main challenge remains in the development of inexpensive separation materials which are resistant towards harsh process conditions and fouling.

Neutronisäteilylle altistuminen käytetyn polttoaineen siirrossa Olkiluodon voimalaitoksella

Tässä työssä on tutkittu OL1/OL2-ydinvoimalaitosten käytetyn polttoaineen siirrossa aiheutuvaa altistusta neutronisäteilylle. Käytetty polttoaine siirretään vedellä täytetyssä käytetyn polttoaineen siirtosäiliössä Castor TVO:ssa OL1/OL2-laitoksilta käytetyn polttoaineen varastolle. Siirtotyön aikana useat eri ammattiryhmiin kuuluvat henkilöt työskentelevät siirtosäiliön välittömässä läheisyydessä, altistuen käytetystä polttoaineesta emittoituvalle fotoni- ja neutronisäteilylle. Aikaisemmista neutronisäteilyannosten mittauksista on todettu, ettei jatkuvalle altistuksen seurannalle ole ollut tarvetta. Tämän työn tarkoitus on selvittää teoreettisilla laskelmilla siirtotyöhön osallistuvan henkilön mahdollisuus saada kirjausrajan ylittävä annos neutronisäteilyä. Neutronisäteilyn annosnopeudet siirtosäiliötä ympäröivässä tilassa on laskettu yhdysvaltalaisella Monte Carlo-menetelmään perustuvalla MCNP-ohjelmalla. MCNP:llä mallinnettiin siirtosäiliö, siirtosäiliön sisältämä polttoaine ja ympäröivä tila kolmella jäähtymisajalla ja kolmella keskimääräisellä maksimipoistopalamalla. Polttoainenippujen isotooppikonsentraatiot ja säteilylähteiden voimakkuudet on laskettu Studsvik SNF-ohjelmalla. Simuloinnin perusteella voidaan todeta, ettei neutronisäteilyannosten jatkuvalle seurannalle ole tarvetta käytetyn polttoaineen siirrossa. Vaikka neutronisäteilyn annosnopeudet voivat nousta siirtosäiliön läheisyydessä suhteellisen suuriksi, ovat siirtosäiliön lähellä tehtävät työt niin lyhytaikaisia, että kirjausrajan ylitystä voidaan pitää hyvin epätodennäköisenä. Johtopäätökset varmistetaan työssä suunnitellulla mittausjärjestelyllä.

Selective leaching of multimetal tailings

Depletion of high grade mineral resources, tightening of environmental regulations and the environmental impact of acid mine drainage caused by sulfidic minerals continuously increase the interest in processing tailings and other mine waste. Treating waste requires additional capital and operational input, but the decrease in size and need of tailings ponds and permits decrease the overall costs. Treatment and utilization of the tailings could also bring added revenue by the recovery of valuables. Leaching of metal sulfides is very demanding and time consuming and hence process conditions need to be carefully optimized. The leaching of sulfides is affected by for example the choice of leaching agent, its concentration and temperature, pH, the redox potential, pressure, pulp density and particle size distribution. With reference to the mine case study the leaching of nickel and copper sulfides, especially the primary minerals pentlandite and chalcopyrite were investigated. Leaching behavior and recoveries for nickel, copper and iron were found out by sulfuric and citric acid leaching experiments using tailings samples of high and low sulfur content. Moderate recoveries were obtained and citric acid seemed more attractive. Increase in temperature and decrease in pulp density had positive effect on the recovery and pH was also proven to have a significant effect on the recovery of valuables. The rate determining step was determined through kinetic modeling in case of all valuables separately. Leaching was controlled by diffusion. The investigated multimetal tailing showed moderate potential in recovering of metal valuables from low grade tailing deposits. The process conditions should however be further optimized.

PDM system functions and utilizations analysis to improve efficiency of sheet metal product design and manufacturing

This study will concentrate on Product Data Management (PDM) systems, and sheet metal design features and classification. In this thesis, PDM is seen as an individual system which handles all product-related data and information. The meaning of relevant data is to take the manufacturing process further with fewer errors. The features of sheet metals are giving more information and value to the designed models. The possibility of implementing PDM and sheet metal features recognition are the core of this study. Their integration should make the design process faster and manufacturing-friendly products easier to design. The triangulation method is the basis for this research. The sections of this triangle are: scientific literature review, interview using the Delphi method and the author’s experience and observations. The main key findings of this study are: (1) the area of focus in triangle (the triangle of three different point of views: business, information exchange and technical) depends on the person’s background and their role in the company, (2) the classification in the PDM system (and also in the CAD system) should be done using the materials, tools and machines that are in use in the company and (3) the design process has to be more effective because of the increase of industrial production, sheet metal blank production and the designer’s time spent on actual design and (4) because Design For Manufacture (DFM) integration can be done with CAD-programs, DFM integration with the PDM system should also be possible.

Save Consumers Time and Money: Thou Shall Not Forget Digital Native Big Data Consumers

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Sustainable linguistic repository built on DSpace

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Repository sustainability

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Membrane development for oil contaminated water treatments

The aim of this Master’s thesis study was to develop a membrane for oil contaminated water treatments. Oily wastewaters are a big problem to environment and therefore it is important to find an efficient method for their treatment. There are several treatment methods, but one of the most promising methods is membrane filtration. In the theoretical part of this study the membrane technology and polymeric membrane preparation with phase inversion and membrane modification methods was discussed. It was also told about the most important properties of the membranes. Oily waters, their treatment methods and oily wastewater sources were discussed more specifically. In the experimental part membranes from cellulose acetate were prepared and membranes were modified with two different methods. Modification methods were surface modification and polymer mixing. The modification purpose was to make membranes more hydrophilic and increase surface charge, which can reduce fouling. Membranes were characterized by determining zeta potential, contact angle, oil retention, pure water permeability, pressure-normalized flux and fouling. It were used both synthetic and real spent oil-water emulsion in membrane filtration. Surface modification resulted membranes, which had better properties than unmodified membrane. The amount of substance used in surface modification affected a lot to membrane properties, so it would be necessary to try different amounts of substance to develop the best membrane for oil-water emulsion treatment.

Säteilysuojelu käytetyn ydinpolttoaineen kapselointi- ja loppusijoituslaitoksella

Suomen ydinenergialaki vaatii ydinenergian käytössä syntyvän ydinjätteen käsittelyn ja varastoinnin sekä loppusijoittamisen Suomeen. Fortumin ja TVO:n ydinvoimalaitoksissa syntyvä käytetty ydinpolttoaine tullaan kapseloimaan ja loppusijoittamaan Olkiluotoon rakennettavassa kapselointi- ja loppusijoituslaitoksessa. Tämän työn tavoitteena on muodostaa kokonaiskuva kapselointi- ja loppusijoituslaitoksen säteilysuojelusta aikaisemmin tehtyjen selvitysten ja suunnitelmien perusteella. Kapselointilaitoksella käytetty ydinpolttoaine suljetaan kuparikapseleihin, jotka loppusijoitetaan maan alle loppusijoituslaitoksella. Työn aluksi kuvataan loppusijoitusmenetelmä ja kapselointi- ja loppusijoituslaitoksen käyttötoiminta. Tämän jälkeen käsitellään lainsäädäntöä ja viranomaisohjeita, jotka ohjaavat ydinlaitosten säteilysuojelua. Seuraavaksi käsitellään kapselointi- ja loppusijoituslaitoksella olevia säteilylähteitä. Lisäksi työssä käsitellään kapselointi- ja loppusijoituslaitokselle suunniteltua valvonta-aluetta ja sen säteilyolosuhteiden mukaista vyöhykejakoa. Työssä saatiin tulokseksi kokonaiskuva kapselointi- ja loppusijoituslaitoksen säteilysuojelusta. Kokonaiskuvan muodostamisen lisäksi laadittiin alustavia suunnitelmia käyttötoiminnan säteilysuojelun järjestämisestä. Lisäksi laadittiin ehdotuksia valvonta-alueen tarkemmista rajoista loppusijoituslaitoksella sekä havaittiin laitosten säteilysuojeluun liittyviä ongelmia ja esitettiin ratkaisuja niihin. Ongelmaksi osoittautui muun muassa, että kapselointi- ja loppusijoituslaitoksen valvonta-alueiden luonteiden eroa ei ollut huomioitu suunnitelmissa. Lisäksi todettiin, että nykyisin ydinlaitoksilla käytössä oleva valvonta-alueen vyöhykejako ei vastaa kapselointi- ja loppusijoituslaitosten tarpeita. Näihin esitettiin ratkaisuiksi laitosten välille perustettavaa kenkärajaa ja uuden korkeamman säteilyvyöhykkeen käyttöönottoa.

Behavior of black liquor nitrogen in combustion : formation of cyanate

The Kraft pulping process is the dominant chemical pulping process in the world. Roughly 195 million metric tons of black liquor are produced annually as a by-product from the Kraft pulping process. Black liquor consists of spent cooking chemicals and dissolved organics from the wood and can contain up to 0.15 wt% nitrogen on dry solids basis. The cooking chemicals from black liquor are recovered in a chemical recovery cycle. Water is evaporated in the first stage of the chemical recovery cycle, so the black liquor has a dry solids content of 65-85% prior to combustion. During combustion of black liquor, a portion of the black liquor nitrogen is volatilized, finally forming N2 or NO. The rest of the nitrogen remains in the char as char nitrogen. During char conversion, fixed carbon is burned off leaving the pulping chemicals as smelt, and the char nitrogen forms mostly smelt nitrogen (cyanate, OCN-). Smelt exits the recovery boiler and is dissolved in water. The cyanate from smelt decomposes in the presence of water, forming NH3, which causes nitrogen emissions from the rest of the chemical recovery cycle. This thesis had two focuses: firstly, to determine how the nitrogen chemistry in the recovery boiler is affected by modification of black liquor; and secondly, to find out what causes cyanate formation during thermal conversion, and which parameters affect cyanate formation and decomposition during thermal conversion of black liquor. The fate of added biosludge nitrogen in chemical recovery was determined in Paper I. The added biosludge increased the nitrogen content of black liquor. At the pulp mill, the added biosludge did not increase the NO formation in the recovery boiler, but instead increased the amount of cyanate in green liquor. The increased cyanate caused more NH3 formation, which increased the NCG boiler’s NO emissions. Laboratory-scale experiments showed an increase in both NO and cyanate formation after biosludge addition. Black liquor can be modified, for example by addition of a solid biomass to increase the energy density of black liquor, or by separation of lignin from black liquor by precipitation. The precipitated lignin can be utilized in the production of green chemicals or as a fuel. In Papers II and III, laboratory-scale experiments were conducted to determine the impact of black liquor modification on NO and cyanate formation. Removal of lignin from black liquor reduced the nitrogen content of the black liquor. In most cases NO and cyanate formation decreased with increasing lignin removal; the exception was NO formation from lignin lean soda liquors. The addition of biomass to black liquor resulted in a higher nitrogen content fuel mixture, due to the higher nitrogen content of biomass compared to black liquor. More NO and cyanate were formed from the fuel mixtures than from pure black liquor. The increased amount of formed cyanate led to the hypothesis that black liquor is catalytically active and converts a portion of the nitrogen in the mixed fuel to cyanate. The mechanism behind cyanate formation during thermal conversion of black liquor was not clear before this thesis. Paper IV studies the cyanate formation of alkali metal loaded fuels during gasification in a CO2 atmosphere. The salts K2CO3, Na2CO3, and K2SO4 all promoted char nitrogen to cyanate conversion during gasification, while KCl and CaCO3 did not. It is now assumed that cyanate is formed when alkali metal carbonate or an active intermediate of alkali metal carbonate (e.g. -CO2K) reacts with the char nitrogen forming cyanate. By testing different fuels (bark, peat, and coal), each of which had a different form of organic nitrogen, it was concluded that the form of organic nitrogen in char also has an impact on cyanate formation. Cyanate can be formed during pyrolysis of black liquor, but at temperatures 900°C or above, the formed cyanate will decompose. Cyanate formation in gasifying conditions with different levels of CO2 in the atmosphere was also studied. Most of the char nitrogen was converted to cyanate during gasification at 800-900°C in 13-50% CO2 in N2, and only 5% of the initial fuel nitrogen was converted to NO during char conversion. The formed smelt cyanate was stable at 800°C 13% CO2, while it decomposed at 900°C 13% CO2. The cyanate decomposition was faster at higher temperatures and in oxygen-containing atmospheres than in an inert atmosphere. The presence of CO2 in oxygencontaining atmospheres slowed down the decomposition of cyanate. This work will provide new information on how modification of black liquor affects the nitrogen chemistry during thermal conversion of black liquor and what causes cyanate formation during thermal conversion of black liquor. The formation and decomposition of cyanate was studied in order to provide new data, which would be useful in modeling of nitrogen chemistry in the recovery boiler.

Learning information technology business in a changing industry landscape. Introducing Team Entrepreneurship in Renewing Bachelor Education in Renewing Bachelor Education in Information

Speed, uncertainty and complexity are increasing in the business world all the time. When knowledge and skills become quickly irrelevant, new challenges are set for information technology (IT) education. Meta-learning skills – learning how to learn rapidly - and innovation skills have become more essential than single technologies or other specific issues. The drastic changes in the information and communications technology (ICT) sector have caused a need to reconsider how IT Bachelor education in Universities of Applied Sciences should be organized and employed to cope with the change. The objective of the study was to evaluate how a new approach to IT Bachelor education, the ICT entrepreneurship study path (ICT-ESP) fits IT Bachelor education in a Finnish University of Applied Sciences. This kind of educational arrangement has not been employed elsewhere in the context of IT Bachelor education. The study presents the results of a four-year period during which IT Bachelor education was renewed in a Finnish University of Applied Sciences. The learning environment was organized into an ICT-ESP based on Nonaka’s knowledge theory and Kolb’s experiental learning. The IT students who studied in the ICT-ESP established a cooperative and learned ICT by running their cooperative at the University of Applied Sciences. The students (called team entrepreneurs) studied by reading theory in books and other sources of explicit information, doing projects for their customers, and reflecting in training sessions on what was learnt by doing and by studying the literature. Action research was used as the research strategy in this study. Empirical data was collected via theme-based interviews, direct observation, and participative observation. Grounded theory method was utilized in the data analysis and the theoretical sampling was used to guide the data collection. The context of the University of Applied Sciences provided a good basis for fostering team entrepreneurship. However, the results showed that the employment of the ICT-ESP did not fit into the IT Bachelor education well enough. The ICT-ESP was cognitively too tough for the team entrepreneurs because they had two different set of rules to follow in their studies. The conventional courses engaged lot of energy which should have been spent for professional development in the ICT-ESP. The amount of competencies needed in the ICT-ESP for professional development was greater than those needed for any other ways of studying. The team entrepreneurs needed to develop skills in ICT, leadership and self-leadership, team development and entrepreneurship skills. The entrepreneurship skills included skills on marketing and sales, brand development, productization, and business administration. Considering the three-year time the team entrepreneurs spent in the ICT-ESP, the challenges were remarkable. Changes to the organization of IT Bachelor education are also suggested in the study. At first, it should be admitted that the ICT-ESP produces IT Bachelors with a different set of competencies compared to the conventional way of educating IT Bachelors. Secondly, the number of courses on general topics in mathematics, physics, and languages for team entrepreneurs studying in the ICTESP should be reconsidered and the conventional course-based teaching of the topics should be reorganized to support the team coaching process of the team entrepreneurs with their practiceoriented projects. Third, the upcoming team entrepreneurs should be equipped with relevant information about the ICT-ESP and what it would require in practice to study as a team entrepreneur. Finally, the upcoming team entrepreneurs should be carefully selected before they start in the ICT-ESP to have a possibility to eliminate solo players and those who have a too romantic view of being a team entrepreneur. The results gained in the study provided answers to the original research questions and the objectives of the study were met. Even though the IT degree programme was terminated during the research process, the amount of qualitative data gathered made it possible to justify the interpretations done.