The Influence of Process Conditions on the Deresination Efficiency in Mechanical Pulp Washing

The aim of this thesis was to produce information for the estimation of the flow balance of wood resin in mechanical pulping and to demonstrate the possibilities for improving the efficiency of deresination in practice. It was observed that chemical changes in wood resin take place only during peroxide bleaching, a significant amount of water dispersed wood resin is retained in the pulp mat during dewatering and the amount of wood resin in the solid phase of the process filtrates is very small. On the basis of this information there exist three parameters related to behaviour of wood resin that determine the flow balance in the process: 1. The liberation of wood resin to the pulp water phase 2. Theretention of water dispersed wood resin in dewatering 3. The proportion of wood resin degraded in the peroxide bleaching The effect of different factors on these parameters was evaluated with the help of laboratory studies and a literature survey. Also, information related to the values of these parameters in existing processes was obtained in mill measurements. With the help of this information, it was possible to evaluate the deresination efficiency and the effect of different factors on this efficiency in a pulping plant that produced low-freeness mechanical pulp. This evaluation showed that the wood resin content of mechanical pulp can be significantly decreased if there exists, in the process, a peroxide bleaching and subsequent washing stage. In the case of an optimal process configuration, as high as a 85 percent deresination efficiency seems to be possible with a water usage level of 8 m3/o.d.t.

Development of fibre recovery process

The fiber recovery process is an essential part of the modern paper mill. It creates the basisfor mill's internal recirculation of the most important raw materials ¿ water and fiber. It is normally also a start point for further treatment of wastewater and if it works efficiently, it offers excellent basis to minimize effluents. This dissertation offers two different approaches to the subject. Firstly a novel save-all disc filter feeding system is developed and presented. This so-called precoat method is tested both in the laboratory and full-scale conditions. In laboratory scale it beats the traditional one clearly, when low freeness pulps are used as a sweetener stock. The full-scale application needs still some development work before it can be implemented to the paper mills. Secondly, the operationenvironment of save-all disc filter is studied mostly in laboratory conditions.The focus of this study is in cases, where low-freeness pulps are used as a sweetener stock of save-all filter. The effects of CSF-value, pressure drop, suspension consistency and retention chemicals to the quantity and quality of the filtrate was studied. Also the filtration resistance of the low freeness pulps was one studied.

Wet Oxidation of Concentrated Wastewaters: Process Combination and Reaction Kinetic Modeling

The accumulation of aqueous pollutants is becoming a global problem. The search for suitable methods and/or combinations of water treatment processes is a task that can slow down and stop the process of water pollution. In this work, the method of wet oxidation was considered as an appropriate technique for the elimination of the impurities present in paper mill process waters. It has been shown that, when combined with traditional wastewater treatment processes, wet oxidation offers many advantages. The combination of coagulation and wet oxidation offers a new opportunity for the improvement of the quality of wastewater designated for discharge or recycling. First of all, the utilization of coagulated sludge via wet oxidation provides a conditioning process for the sludge, i.e. dewatering, which is rather difficult to carry out with untreated waste. Secondly, Fe2(SO4)3, which is employed earlier as a coagulant, transforms the conventional wet oxidation process into a catalytic one. The use of coagulation as the post-treatment for wet oxidation can offer the possibility of the brown hue that usually accompanies the partial oxidation to be reduced. As a result, the supernatant is less colored and also contains a rather low amount of Fe ions to beconsidered for recycling inside mills. The thickened part that consists of metal ions is then recycled back to the wet oxidation system. It was also observed that wet oxidation is favorable for the degradation of pitch substances (LWEs) and lignin that are present in the process waters of paper mills. Rather low operating temperatures are needed for wet oxidation in order to destruct LWEs. The oxidation in the alkaline media provides not only the faster elimination of pitch and lignin but also significantly improves the biodegradable characteristics of wastewater that contains lignin and pitch substances. During the course of the kinetic studies, a model, which can predict the enhancements of the biodegradability of wastewater, was elaborated. The model includes lumped concentrations suchas the chemical oxygen demand and biochemical oxygen demand and reflects a generalized reaction network of oxidative transformations. Later developments incorporated a new lump, the immediately available biochemical oxygen demand, which increased the fidelity of the predictions made by the model. Since changes in biodegradability occur simultaneously with the destruction of LWEs, an attempt was made to combine these two facts for modeling purposes.

Supporting knowledge creation and sharing in the early phases of the strategic innovation process

The driving forces of technology and globalization continuously transform the business landscape in a way which undermines the existing strategies and innovations of organizations. The challenge for organizations is to establish such conditions where they are able to create new knowledge for innovative business ideas in interaction between other organizations and individuals. Innovation processes continuously need new external stimulations and seek new ideas, new information and knowledge locating more and more outside traditional organizational boundaries. In several studies, the early phases of the innovation process have been considered as the most critical ones. During these phases, the innovation process can emerge or conclude. External knowledge acquirement and utilization are noticed to be important at this stage of the innovation process giving information about the development of future markets and needs for new innovative businessideas. To make it possible, new methods and approaches to manage proactive knowledge creation and sharing activities are needed. In this study, knowledge creation and sharing in the early phases of the innovation process has been studied, and the understanding of knowledge management in the innovation process in an open and collaborative context advanced. Furthermore, the innovation management methods in this study are combined in a novel way to establish an open innovation process and tested in real-life cases. For these purposes two complementary and sequentially applied group work methods - the heuristic scenario method and the idea generation process - are examined by focusing the research on the support of the open knowledge creation and sharing process. The research objective of this thesis concerns two doctrines: the innovation management including the knowledge management, and the futures research concerning the scenario paradigm. This thesis also applies the group decision support system (GDSS) in the idea generation process to utilize the converged knowledge during the scenario process.

Mobile Communications within the European Union: The Role of Location in the Evolution and Forecasting of the Diffusion Process

In the European Union, the importance of mobile communications was realized early on. The process of mobile communications becoming ubiquitous has taken time, as the innovation of mobile communications diffused into the society. The aim of this study is to find out how the evolution and spatial patterns of the diffusion of mobile communications within the European Union could be taken into account in forecasting the diffusion process. There is relatively lot of research of innovation diffusion on the individual (micro) andthe country (macro) level, if compared to the territorial level. Territorial orspatial diffusion refers either to the intra-country or inter-country diffusionof an innovation. In both settings, the dif- fusion of a technological innovation has gained scarce attention. This study adds knowledge of the diffusion between countries, focusing especially on the role of location in this process. The main findings of the study are the following: The penetration rates of the European Union member countries have become more even in the period of observation, from the year 1981 to 2000. The common digital GSM system seems to have hastened this process. As to the role of location in the diffusion process, neighboring countries have had similar diffusion processes. They can be grouped into three, the Nordic countries, the central and southern European countries, and the remote southern European countries. The neighborhood effect is also domi- nating in thegravity model which is used for modeling the adoption timing of the countries. The subsequent diffusion within a country, measured by the logistic model in Finland, is af- fected positively by its economic situation, and it seems to level off at some 92 %. Considering the launch of future mobile communications systemsusing a common standard should implicate an equal development between the countries. The launching time should be carefully selected as the diffusion is probably delayed in economic downturns. The location of a country, measured by distance, can be used in forecasting the adoption and diffusion. Fi- nally, the result of penetration rates becoming more even implies that in a relatively homoge- nous set of countries, such as the European Union member countries, the estimated final pene- tration of a single country can be used for approximating the penetration of the others. The estimated eventual penetration of Finland, some 92 %, should thus also be the eventual level for all the European Union countries and for the European Union as a whole.

Welding time models for cost calculations in the early stages of the design process

It is generally accepted that between 70 and 80% of manufacturing costs can be attributed to design. Nevertheless, it is difficult for the designer to estimate manufacturing costs accurately, especially when alternative constructions are compared at the conceptual design phase, because of the lack of cost information and appropriate tools. In general, previous reports concerning optimisation of a welded structure have used the mass of the product as the basis for the cost comparison. However, it can easily be shown using a simple example that the use of product mass as the sole manufacturing cost estimator is unsatisfactory. This study describes a method of formulating welding time models for cost calculation, and presents the results of the models for particular sections, based on typical costs in Finland. This was achieved by collecting information concerning welded products from different companies. The data included 71 different welded assemblies taken from the mechanical engineering and construction industries. The welded assemblies contained in total 1 589 welded parts, 4 257 separate welds, and a total welded length of 3 188 metres. The data were modelled for statistical calculations, and models of welding time were derived by using linear regression analysis. Themodels were tested by using appropriate statistical methods, and were found to be accurate. General welding time models have been developed, valid for welding in Finland, as well as specific, more accurate models for particular companies. The models are presented in such a form that they can be used easily by a designer, enabling the cost calculation to be automated.

Applying the principles of life cycle assessment and costing in process modeling to examine profit-making capability

Static process simulation has traditionally been used to model complex processes for various purposes. However, the use of static processsimulators for the preparation of holistic examinations aiming at improving profit-making capability requires a lot of work because the production of results requires the assessment of the applicability of detailed data which may be irrelevant to the objective. The relevant data for the total assessment gets buried byirrelevant data. Furthermore, the models do not include an examination of the maintenance or risk management, and economic examination is often an extra property added to them which can be performed with a spreadsheet program. A process model applicable to holistic economic examinations has been developed in this work. The model is based on the life cycle profit philosophy developed by Hagberg and Henriksson in 1996. The construction of the model has utilized life cycle assessment and life cycle costing methodologies with a view to developing, above all, a model which would be applicable to the economic examinations of complete wholes and which would require the need for information focusing on aspects essential to the objectives. Life cycle assessment and costing differ from each other in terms of the modeling principles, but the features of bothmethodologies can be used in the development of economic process modeling. Methods applicable to the modeling of complex processes can be examined from the viewpoint of life cycle methodologies, because they involve the collection and management of large corpuses of information and the production of information for the needs of decision-makers as well. The results of the study shows that on the basis of the principles of life cycle modeling, a process model can be created which may be used to produce holistic efficiency examinations on the profit-making capability of the production line, with fewer resources thanwith traditional methods. The calculations of the model are based to the maximum extent on the information system of the factory, which means that the accuracyof the results can be improved by developing information systems so that they can provide the best information for this kind of examinations.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Studies on coordination of systems development process

This thesis examines coordination of systems development process in a contemporary software producing organization. The thesis consists of a series of empirical studies in which the actions, conceptions and artifacts of practitioners are analyzed using a theory-building case study research approach. The three phases of the thesis provide empirical observations on different aspects of systemsdevelopment. In the first phase is examined the role of architecture in coordination and cost estimation in multi-site environment. The second phase involves two studies on the evolving requirement understanding process and how to measure this process. The third phase summarizes the first two phases and concentrates on the role of methods and how practitioners work with them. All the phases provide evidence that current systems development method approaches are too naïve in looking at the complexity of the real world. In practice, development is influenced by opportunity and other contingent factors. The systems development processis not coordinated using phases and tasks defined in methods providing universal mechanism for managing this process like most of the method approaches assume.Instead, the studies suggest that managing systems development process happens through coordinating development activities using methods as tools. These studies contribute to the systems development methods by emphasizing the support of communication and collaboration between systems development participants. Methods should not describe the development activities and phases in a detail level, butshould include the higher level guidance for practitioners on how to act in different systems development environments.

Optimizing the Testing Process in Module Testing – Functional Testing Interface

Today's business environment has become increasingly unexpected and fast changing because of the global competition. This new environment requires the companies to organize their control differently, e.g. by logistic process thinking. Logistic process thinking in software engineering applies the principles of production process to immaterial products. Processes must be optimized, so that every phase adds value to the customer, and the lead times can be cut shorter to meet the new customer requirements. The purpose of this thesis is to examine and optimize the testing processes of software engineering concentrating on module testing, functional testing and their interface. The concept of logistic process thinking is introduced through production process, value added model and process management. Also theory of testing based on literature is presented, concentrating on module testing and functional testing. The testing processes of the Case Company are presented together with the project models in which they are implemented. The real life practices in module testing and functional testing and their interface are examined through interviews. These practices are analyzed against the processes and the testing theory, through which ideas for optimizing the testing process are introduced. The project world of the Case Company is also introduced together with two example testing projects in different life cycle phases. The examples give a view of how much effort of the project is put in different types of testing.

A Technology Intelligence Process for a High Technology Company

Tämä diplomityö määrittelee teknologiaseurantaprosessin, jolla korkean teknologian yritys voi ohjata toimintaansa. Korkean teknologian yrityksille on olennaista seurata teknologian kehitystä. Tällaiset yritykset tarvitsevat hyvin määritellyn järjestelmän, jolla ne voivat seurata ja ennustaa teknologista kehitystä.Työssä esitetään, että teknologiaseuranta ja kilpailuseuranta (competitive intelligence) ovat business intelligencen osa-alueita, jotka täydentävät ja tukevat toisiaan. Tärkeä havainto on, että business intelligence -prosessi on ennen kaikkea organisaation oppimisprosessi. Tästä seuraa, että minkä tahansa BI-prosessin tulisi perustua niihin prosesseihin, joiden avulla organisaatiot oppivat. Työssä esitetään myös, miten business intelligence, tietojohtaminen (knowledge management) ja organisaatioiden oppiminen liittyvät toisiinsa.Teknologiaseuranta on elintärkeä toiminto korkean teknologian yritykselle; sitä tarvitaan monella strategisen johtamisen osa-alueella, ainakin teknologia-, markkinointi- ja henkilöstöjohtamisessa. Teknologiaseurannan havaitaan myös olevan korkean teknologian yritykselle erittäin tärkeä ydinosaamisalue, jota ei voi kokonaan ulkoistaa.Työssä esitellään teknologiaseurantaprosessi, joka perustuu yleiselle business intelligence -prosessille ja siitä johdetulle kilpailuseurantaprosessille. Työssä myös esitetään ehdotus siitä, kuinka teknologiaseuranta voitaisiin järjestää korkean teknologian yrityksessä. Esitetty ratkaisu perustuu Community of practice -käsitteeseen. Community of practice on vapaaehtoisuuteen perustuva tiimi, jonka jäseniä yhdistää kiinnostus johonkin asiaan ja oppimishalu. Esimerkkiyrityksessä on tunnistettu selkeä tarve yhtenäiseen ja koordinoituun teknologiaseurantaan. Työssä esitetään alustava teknologiaseurantaprosessi esimerkkiyritykselle ja tunnistetaan teknologiaseurantaprosessin asiakkaat ja tekijät.

The Development of an Internal Testing Process for a Bluetooth Product

BlueGiga Technologies on uusi Bluetooth -teknologiaa soveltava pk-yritys. Yrityksen tuotekehitysprosessia täydentämään tarvittiin testausprosessi. Testausprosessin luominen oli haastavaa, koska Bluetooth -teknologia on uutta ja yritys on vielä nuori. Lisäksi se integroi kovo- ja ohjelmistokomponentteja tuotteissaan. Testaus aloitettiin evaluoimalla standardinmukaista tapaa dokumentoida testit. Tämän jälkeen tutkittiin BlueGigan ohjelmistokehitysprosessin suhdetta olemassa oleviin ohjelmistokehitysprosesseihin. Samanaikaisesti perehdyttiin Bluetooth -kvalifikaation testaukselle asettamiin vaatimuksiin. Tämän seurauksena TTCN:ää kokeiltiin helppolukuisen testitapauksen määrittelyssä. Käyttötapauksiin perustuvan testauksen sopivuutta Wireless Remote Access Platform:in (WRAP) testaamiseen arvioitiin kokeilemalla sitä Man-to-Machine -käyttötapauksen testaamisessa. Yllämainittujen tehtävien aikana kerätyn tiedon ja hankittujen kokemusten pohjalta laadittiin testausprosessi, joka kattaa yksikkö-, integraatio- ja järjestelmätason testauksen. Painopiste on järjestelmätason testauksessa. Prosessi määrittelee myös vastuuhenkilön tai -henkilöt eri testaustasoille.

The Analysis of The Logistics Process between Finland and Russia in An EMS Company

Työn tavoitteena oli selventää Elcoteqin Suomen ja Venäjän välisten yksiköiden logistista prosessia ja erityisesti siihen liittyviä ongelmia. Työ on tehty Elcoteqin Engineering Services yksikköön, jossa ei tyypillisesti ole ollut asiaan liittyvää tietoa. Pääasiallisena työmenetelmänä olivat haastattelut sekä tutustuminen logistiseen putkeen käytännössä. Myös kirjallisuudella oli oma osansa, sekä tullaukseen että asiaan liittyvien teorioiden osalta. Teorioita ja käytännön kokemuksia yhdistäen edettiin analysointiin ja vertailuun, jonka perusteella annettiin suosituksia tulevia projekteja silmällä pitäen. Myös tulevaisuuden odotuksia on käsitelty yleisellä tasolla, lähinnä liittyen erilaisten kehitysohjelmien tarjoamiin mahdollisuuksiin. Logistiikka Suomen ja Venäjän välillä on huomattavasti monimutkaisempaa kuin ensisilmäyksellä näyttää. Ongelmia on niin rajanylityksen, tullauksen kuin lisenssiprosessinkin kanssa. Asioiden kehittämiseksi on kuitenkin paljon tehtävissä, kehityspotentiaali on valtava. Vahvaa panostusta liiketoiminnan kehittämiseksi Venäjällä on jatkettava, vaikka siihen liittyvät ongelmat välillä tuntuvatkin ylivoimaisen suurilta. Erityisen turhauttavia ovat asiat, joihin ei pystytä vaikuttamaan. Työn edetessä tuli kuitenkin esiin uusia näkökulmia, joita ei aiemmin ole otettu huomioon. Tuotteiden valintaan on jatkossa kiinnitettävä enemmän huomiota. Silti myös kuljetuksen ja rajanylityksen nopeuttamisen tutkimista on edelleen jatkettava.

Requirements Management in the Software Development Process

Ohjelmistokehitys on monimutkainen prosessi. Yksi keskeisistä tekijöistä siinä on ohjelmistolle asetettavat vaatimukset. Näitä vaatimuksia on hyvin monenlaisia, ja eri tasoisia; toivotusta toiminnallisuudesta hyvinkin yksityiskohtaisiin vaatimuksiin. Näiden vaatimusten hallinta on myöskin hyvin monitahoista, vaikkakin se on kirjallisuudessa esitetty selkeänä prosessissa, joka on sarja toisistaan erottuviavaiheita. Työn painopiste oli näiden vaatimusten muutoksen ja valmiiseen ohjelmistoon kohdistuvan palautteen hallinnassa, ja kuinka vaatimustenhallintaohjelmisto voisi olla avuksi näissä prosesseissa. Vaatimustenhallintatyökalun käyttö ei sinällään ratkaise mitään ongelmia, mutta se suo puitteet parantaa vaatimusten hallitsemista. Työkalun käytöstä on muun muassa seuraavia etuja: vaatimusten keskitetty varastointi, käyttäjäoikeuksien määrittely koskien eri käyttäjiä ja heidän pääsyään näkemään tai muuttamaan tietoa, muutoksenhallintaprosessin hallinta, muutosten vaikutuksen analysointi ja jäljitettävyys ja pääsy tietoihin web-selaimella.

Development of Special Pumps Repair Process

Tässä diplomityössä käsitellään erikoispumppujen korjausprosessia teollisuuspumppujen korjauksiin erikoistuneessa konepajassa. Työn pääasiallinen tarkoitus on tuotantoprosessin kehittäminen ja tuotantovaiheiden esitteleminen. Tavoitteen taustalla on pyrkimys entisestään parantaa palvelukykyä ja asiakastyytyväisyyttä.Kolme eri keinoa päätavoitteen saavuttamiseksi ovat tuotannon suunnittelun ja ohjauksen kehittäminen, työssä käsiteltyjen pumpputyyppien korjausprosessien läpäisyaikojen lyhentäminen sekä korjausvaiheiden määrittely ja esittely vaihe vaiheelta. Työssä käsiteltyjä erikoispumpputyyppejä ovat imupumput, monijaksopumput sekä pysty/potkuripumput.Tuotannonsuunnittelun ja -ohjauksen kehittämiseksi sekä läpäisyaikojen lyhentämiseksi työssä etsittiin vaihtoehtoisia toimintatapoja. Kolmas tavoite, eli korjausvaiheiden määrittely, toteutettiin esittelemällä korjausprosessin vaiheet käsitellyillä pumpputyypeillä.Tuloksena saatiin keinoja tuotannon suunnittelun ja hallinnan kehittämiseksi. Useimmat keinot koskevat toimintatapojen selkiyttämistä. Myös keinoja läpäisyaikojen lyhentämiseksi löydettiin. Tietyllä imupumpputyypillä ja -koolla läpäisyajan lyheneminen oli 25 % ja osalla monijaksopumpuista jopa 75 %. Tulokset saavutetaan varastoimalla tiettyjä komponentteja, joilla on pitkä valmistus- tai korjausaika. Pysty/potkuripumppujen korjauksen läpäisyaikaa ei saatu lyhennettyä työn rajausten puitteissa Näiden tulosten lisäksi korjausprosessin toimintatavat määriteltiin.