Nd:YAG Laser Welding of 5083 Aluminium Alloy using Filler Wire

High reflectivity and high thermal conductivity, high vapour pressure of alloyingelements as well as low liquid surface tension and low ionisation potential, make laser welding of aluminium and its alloys a demanding task.Problems that occur during welding are mainly process instabilities of the keyhole and the melt pool, increased plasma formation above the melt pool and loss of alloying elements. These problems lead to unwanted metallurgical defects like hot cracks and porosity in the weld bead andother problems concerning the shape and appearance of the weld bead. In order to minimise the defects and improve the weld quality, the process and beam parameters need to be carefully adjusted along with a consideration concerning the use of filler wire for the welding process. In this work the welding of 3,0 mm thick grade 5083 aluminium alloy plates using a 3,0 kW Nd:YAG laser with grade 5183 filler wire addition is investigated. The plates were welded as butt joints with air gap sizes 0,5 mm, 0,7mm and 1,0 mm. The analysis of the weld beads obtained from the weldedsamples showed that the least imperfections were produced with 0,7 mm air gaps at moderate welding speeds. The analysis also covered the calculation of the melting efficiency and the study of the shape of the weld bead. The melting efficiency was on average around 20 % for the melting process of the welded plates. The weld beads showed the characteristic V-shape of a laser weld and retained this shape during the whole series of experiments.

Effect of Shielding Gases in Laser Welding of Aluminium Alloys

High reflectivity to laser light, alloying element evaporation during high power laser welding makes aluminium alloys highly susceptibility to weld defects such as porosity, cracking and undercutting. The dynamic behaviour of the keyhole, due to fluctuating plasma above the keyhole and the vaporization ofthe alloying elements with in the keyhole, is the key problem to be solved for the improvement of the weld quality and stabilization of the keyhole dynamics isperhaps the single most important development that can broaden the application of laser welding of aluminium alloys. In laser welding, the shielding gas is commonly used to stabilize the welding process, to improve the welded joint features and to protect the welded seam from oxidation. The chemicalcomposition of the shielding gas is a key factor in achieving the final qualityof the welded joints. Wide range of shielding gases varying from the pure gasesto complex mixtures based on helium, argon, nitrogen and carbon dioxide are commercially available. These gas mixtures should be considered in terms of their suitability during laser welding of aluminium alloys to produce quality welds. The main objective of the present work is to study the effect of the shielding gascomposition during laser welding of aluminium alloys. Aluminium alloy A15754 was welded using 3kW Nd-YAG laser (continuous wave mode). The alloy samples were butt welded with different shielding gases (pure and mixture of gases) so that high quality welds with high joint efficiencies could be produced. It was observed that the chemical composition of the gases influenced the final weld quality and properties. In general, the mixture gases, in correct proportions, enabled better utilisation of the properties of the mixing gases, stabilized the welding process and produced better weld quality compared to the pure shielding gases.

Relative Technical Efficiency of European Transportation Systems

Talouden kasvaessa myös tavarankuljetusmäärät kasvavat. Kuljetusjärjestelmät ja niiden sujuva toiminta on erittäin tärkeää taloudellisen kasvun kannalta tällä hetkellä, ja se tulee olemaan yhä tärkeämpää tulevaisuudessa. Tulevaisuudessa tarvitaan kokonaisvaltainen ja selkeästi tehokkaampi kuljetusjärjestelmä, mikäli tulevaisuuden kuljetusvirrat halutaan hoitaa kestävästi. Tässä opinnäytetyössäni tutkin kolmen eurooppalaisen kuljetusjärjestelmän (rautatiet, lentoliikenne ja konttiliikenne meritse) suhteellista teknistä tehokkuutta ja menetelmänä on data envelopment analysis (DEA). Vertailtaessa kuljetusjärjestelmiä löytyi suuria eroja kuljetusmuotojen välille. lentoyhtiöt suoriutuivat huomattavan tasaisesti eli tehokkaiden ja ei-tehokkaiden toimijoiden välillä ei ollut suuria eroja. Rautatiepuolella erot venyivät huomattavan suuriksi niin eri yritysten välillä kuin jopa saman yrityksen sisällä eri vuosina. Pikaisemmassa laivayhtiöiden tarkastelussa erot niiden välillä olivat lähes yhtä pieniä kuin lentoyhtiöiden välillä. Tarkasteltaessa omistajuuden vaikutusta lentoyhtiöiden toiminnassa huomattiin, että yksityisessä omistuksessa olevat yritykset olivat huomattavasti tehokkaampia matkustajien kuljettamisessa. Rahtipuolella merkittäviä eroja ei havaittu. Merkittävät korrelaatiot eri mallien välillä antoivat joitain viitteitä myös kuljetuspoliittiseen päätöksentekoon; investoinnit matkustajienkuljetuksiin raiteilla parantaisivat koko rautatiepuolen teokkuutta, mutta myös samalla lentopuolen matkustajakuljetuksen tehokkuutta.

Numerical Modelling of Combustion and Emission Formation in a Diesel Engine with Different Fuel Injection Characteristics

Päästöjen vähentäminen on ollut viime vuosina tärkeässä osassa polttomoottoreita kehitettäessä.Monet viralliset tahot asettavat uusia tiukempia päästörajoituksia. Päästörajatovat tyypillisesti olleet tiukimmat autoteollisuuden valmistamille pienille nopeakäyntisille diesel-moottoreille, mutta viime aikoina paineita on kohdistunut myös suurempiin keskinopeisiin ja hidaskäyntisiin diesel-moottoreihin. Päästörajat ovat erilaisia riippuen moottorin tyypistä, käytetystä polttoaineesta ja paikasta missä moottoria käytetään johtuen erilaisista paikallisista laeista ja asetuksista. Eniten huomiota diesel-moottorin päästöissä täytyy kohdistaa typen oksideihin, savun muodostukseen sekä partikkeleihin. Laskennallisen virtausmekaniikan (CFD) avulla on hyvät mahdollisuudet tutkia diesel-moottorin sylinterissä tapahtuvia ilmiöitä palamisen aikana. CFD on hyödyllinen työkalu arvioitaessa moottorin suorituskykyä ja päästöjen muodostumista. CFD:llä on mahdollista testata erilaisten parametrien ja geometrioiden vaikutusta ilman kalliita moottorinkoeajoja. CFD:tä voidaan käyttää myös opetustarkoituksessa lisäämään paloprosessin tuntemusta. Tulevaisuudessa palamissimuloinnit CFD:llä tulevat epäilemättä olemaan tärkeä osa moottorin kehityksessä. Tässä diplomityössä on tehty palamissimuloinnit kahteen erilaisilla poittoaineenruiskutuslaitteistoilla varustettuun Wärtsilän keskinopeaan diesel-moottoriin. W46 moottorin ruiskutuslaitteisto on perinteinen mekaanisesti ohjattu pumppusuutin ja W46-CR moottorissa on elektronisesti ohjattu 'common rail' ruiskutuslaitteisto. Näiden moottorien ja käytössä olevien ruiskutusprofiilien lisäksi on simuloinneilla testattu erilaisia uusia ruiskutusprofiileja, jotta erityyppisten profiilien hyvät ja huonot ominaisuudet tulisivat selville. Matalalla kuormalla kiinnostuksen kohteena on nokipäästöjen muodostus ja täydellä kuormalla NOx-päästöjen muodostus ja polttoaineen kulutus. Simulointien tulokset osoittivat, että noen muodostusta matalalla kuormalla voidaan selvästi vähentää monivaiheisella ruiskutuksella, jossa yksi ruiskutusjakso jaetaan kahteen tai useampaan jaksoon. Erityisen tehokas noen vähentämisessä vaikuttaa olevan ns. jälkiruiskutus (post injection). Matalat NOx-päästöt ja hyvä polttoaineen kulutus täydellä kuormalla on mahdollista saavuttaaasteittain nostettavalla ruiskutusnopeudella.

Deregulation of Railroads and Future Development Scenarios in Europe - Literature Analysis of Privatization Process Taken Place in US, UK and Sweden

Euroopan unionissa päätettiin jo yli vuosikymmen sitten, että rautatieliiketoiminta vapautetaan kilpailulle. Iso-Britanniasta olimäärä tulla esimerkkivaltio tämän prosessin käyttöönotossa. Pääideana oli säännöstelyn keventäminen, jolloin omistuspohja toimialalla laajenee ja rautateiden infrastruktuuri sekä toiminta parantuvat. Infrastruktuuri on määrä olla yhden organisaation hallinnassa ja raiteiden käyttöoikeus on kaikilla lupaehdot täyttävillä operaattoreilla, jotka kilpailevat keskenään matkustajista ja tavararahdeista. Kuitenkin Yhdysvalloissa ja eräissä Latinalaisen Amerikan maissa kilpailu on vapautettu siten, että rautatieyritys omistaa raideinfrastruktuurin, junat, tavarankuljetus- sekä matkustajavaunut. Iso-Britannian yksityistämistä pidettiin aluksi isonaepäonnistumisena: nopealla aikataululla sovellettiin jäykkiä transaktioperusteisia ulkoistamisstrategioita infrastruktuurin kunnossapitoon, jotka lopulta johtivat junien jatkuviin myöhästymisiin ja muutamaan tuhoisaan onnettomuuteen. Liiketoiminnallisessa mielessäkään ei oikein onnistuttu: infrastruktuurista vastaava yritys jouduttiin listaamaan pois Lontoon pörssistä, ja hallituksen oli pakko luoda tukipaketti pahasti velkaantuneen, vain marginaalisien investointien kohteena olleen yrityksen toimintaa varten (vaikka kapasiteettitarvetta oli markkinoilla). Myös rautatieoperaattorit olivat taloudellisessa ahdingossa ja vain määrätietoisten hallituksen laatimien pelastuspakettien avulla ala nousi syvimmästä kriisistään. Tästä huolimatta näiden negatiivisten sivuvaikutusten ohella koko ala pystyi kasvattamaan kysyntää, niin matkustaja- kuin rahtiliikenteenkin osalta. Vähenevän kysynnän trendi, joka alkoi 1970-luvulla, otti käännöksen parempaan. Toinen eurooppalaismaa, jolla on pitkät kokemukset yksityistämisestä, on Ruotsi. Tämä maatapaus on melko konservatiivinen verrattuna tilanteeseen edellisessä; vain rajattu määrä reittejä on avattu kilpailulle ja sopimukset tehdään kerralla pitkäksi aikaa eteenpäin. Ruotsin säännöstelyn purku osoittautui menestykseksi, koska tuottavuus onollut vakaassa kasvussa ja rautateiden markkinaosuus erityisesti matkustajapuolella on noussut merkittävästi, verrattuna muihin kuljetusmuotoihin. Kuitenkin kilpailua on käytännössä vähän tässä maassa ja parempiatuloksia on lupa odottaa, kun vain säännöstelyn purkaminen jatkuu. Viimeinen tutkimuksemme kohteena oleva maa on Yhdysvallat, joka alistutti rautatiet kilpailulle jo 1980-luvun alussa, käyttäen jo edellä mainittua vertikaalista integraatiota; tämä valinta on taas johtanut hyvin erilaisiin tuloksiin. Vaihtoehtoinen rakenteellinen uudistustapa on suosinut rahtivirtoja matkustajiin nähden, ja lopputuloksena tämä tapaus synnytti yrityksiä huolehtimaan toista näistä kahdesta pääasiakasryhmästä. Viimeaikaiset tulokset tästä yksityistämisprosessista ovat olleet hyviä: jäljellejääneiden yritysten voitot ovat kasvaneet, osinkoja ollaan kyetty jakamaan ja osakkeiden arvostus on noussut. Tässä tutkimusraportissa yritämme kolmen maatapauksen kautta esittää, miten yksityistämisprosessi tulee vaikuttamaan Euroopassa, kun kilpailu rautateillä vapautuu. Me käymmeläpi, mikä näistä kolmesta maaesimerkistä on kaikkein todennäköisin jaesitämme ehdotuksia siihen, miten valtiot voisivat välttää ei-haluttuja sivuvaikutuksia. Kolme maaesimerkkiä, ja lopuksi esitetty lyhyt tilastollinen analyysi osoittavat, että rautateillä on tulevaisuuden potentiaalia Euroopassa, ja kilpailun vapauttaminen on avain tämän potentiaalin realisointiin.

A novel approachfor assessing the fatigue strength of ultrasonic impact treated welded structures.

It is commonly observed that complex fabricated structures subject tofatigue loading fail at the welded joints. Some problems can be corrected by proper detail design but fatigue performance can also be improved using post-weld improvement methods. In general, improvement methods can be divided into two main groups: weld geometry modification methods and residual stress modification methods. The former remove weld toe defects and/or reduce the stress concentrationwhile the latter introduce compressive stress fields in the area where fatigue cracks are likely to initiate. Ultrasonic impact treatment (UIT) is a novel post-weld treatment method that influences both the residual stress distribution andimproves the local geometry of the weld. The structural fatigue strength of non-load carrying attachments in the as-welded condition has been experimentally compared to the structural fatigue strength of ultrasonic impact treated welds. Longitudinal attachment specimens made of two thicknesses of steel S355 J0 have been tested for determining the efficiency of ultrasonic impacttreatment. Treated welds were found to have about 50% greater structural fatigue strength, when the slope of the S-N-curve is three. High mean stress fatigue testing based on the Ohta-method decreased the degree of weld improvement only 19%. This indicated that the method could be also applied for large fabricated structures operating under high reactive residual stresses equilibrated within the volume of the structure. The thickness of specimens has no significant effect tothe structural fatigue strength. The fatigue class difference between 5 mm and 8 mm specimen was only 8%. It was hypothesized that the UIT method added a significant crack initiation period to the total fatigue life of the welded joints. Crack initiation life was estimated by a local strain approach. Material parameters were defined using a modified Uniform Material Law developed in Germany. Finite element analysis and X-ray diffraction were used to define, respectively, the stress concentration and mean stress. The theoretical fatigue life was found to have good accuracy comparing to experimental fatigue tests.The predictive behaviour of the local strain approach combined with the uniformmaterial law was excellent for the joint types and conditions studied in this work.

Competitive Analysis of the Northwest Russian Transport Logistics Cluster – Finnish Perspective

Tutkimus tarkastelee Luoteis-Venäjän liikennelogistiikkaklusteria. Tarkoitus on selvittää klusterin nykyinen rakenne ja kilpailukyky sekä klusterin tarjoamat liiketoimintamahdollisuudet suomalaisille logistiikkayrityksille. Työssä käsitellään neljää perusliikennemuotoa: rautatie-, maantie-, meri- ja sisävesi-, sekä ilmaliikennettä. Tutkimuksen aineisto on kerätty tutkimusta varten laadituista kyselyistä, haastatteluista sekä aiemmin julkaistusta materiaalista. Venäjä on suunnitellut kehittävänsä voimakkaasti liikenneinfrastruktuuria, mm. julkaisemalla protektionistisen liikennestrategiasuunnitelman. Ongelmana ovat olleet toteutukset, jotka ovat jääneet yleensä puutteellisiksi. Tällä hetkellä todellista kilpailukykyä löytyy ainoastaan rautatieliikenteestä, muut kolme liikennemuotoa omaavat potentiaalisen kilpailukyvyn. Venäjällä on mahdollisuus hyötyä laajasta pinta-alastaan Aasian ja Euroopan liikenteen yhdistäjänä. Yksi konkreettisimmista esimerkeistä on Trans Siperian rautatie, joka kaipaisi vielä lisäkehitystä. Suomi on toiminut Venäjän liikenteessä arvotavaran kauttakulkumaana, vuonna 2003 noin 30–40 % Venäjän tuonnin arvosta kulki Suomen kautta. Venäjälle tullaan tuomaan arvotavaraa vielä useita vuosia, mutta reittien osalta kilpailu on tiukentunut. Suomalaisten yritysten liiketoimintamahdollisuuksiin esitetään kaksi mallia: kauttakulkuliikenteen lisäarvologistiset (VAL) operaatiot Suomessa tai etabloituminen Venäjän logistisiin ketjuihin. Suomalaisten olisi syytä parantaa yhteistyötään yritysten ja yliopistojen ym. koulutuslaitosten välillä. Myös yhteistyökumppaneiden hakeminen esimerkiksi Ruotsista voisi tuoda merkittäviä etuja. Suomalaista osaamista voitaisiin hyödyntää parhaiten etabloitumalla Venäjän markkinoille, esimerkiksi keskittymällä Venäjän logististen ketjujen johtamiseen. Myös VAL palveluiden johtamiseen Venäjällä olisi erittäin hyvä tilaisuus, koska Venäjän oma tietotaito logistiikassa ei ole vielä kehittynyt kansainväliselle tasolle, mutta kustannustaso on alhaisempi kuin Suomessa.

Designing of statically loaded sheet metal structures

The goal of this thesis is to give information to machine designers about how to design and size sheet metal structures and joints. Generally, the designing object is to lighten structures. To design structures that are light and can carry loads more effectively, designers have to be updated of new manufacturing techniques and new designing methods and criterions. With knowledge of this thesis, a designer can recognize objects and methods plus how and where it is possible to apply these new more effectively load carrying structures. The thesis gives answers to questions of corrosion and material planning, goes into joint types and manufacturing techniques of sheet metal structures. One of the main issues is to develop designers world of ideas to design right kind of products with new lasertechniques.

The effects of some variables on CO2 laser-MAG hybrid welding

The CO2-laser-MAG hybrid welding process has been shown to be a productive choice for the welding industry, being used in e.g. the shipbuilding, pipe and beam manufacturing, and automotive industries. It provides an opportunity to increase the productivity of welding of joints containing air gaps compared with autogenous laser beam welding, with associated reductions in distortion and marked increases in welding speeds and penetration in comparison with both arc and autogenous laser welding. The literature study indicated that the phenomena of laser hybrid welding are mostly being studied using bead-on-plate welding or zero air gap configurations. This study shows it very clearly that the CO2 laser-MAG hybrid welding process is completely different, when there is a groove with an air gap. As in case of industrial use it is excepted that welding is performed for non-zero grooves, this study is of great importance for industrial applications. The results of this study indicate that by using a 6 kW CO2 laser-MAG hybrid welding process, the welding speed may also be increased if an air gap is present in the joint. Experimental trials indicated that the welding speed may be increased by 30-82% when compared with bead-on-plate welding, or welding of a joint with no air gap i.e. a joint prepared as optimum for autogenous laser welding. This study demonstrates very clearly, that the separation of the different processes, as well as the relative configurations of the processes (arc leading or trailing) affect welding performance significantly. These matters influence the droplet size and therefore the metal transfer mode, which in turn determined the resulting weld quality and the ability to bridge air gaps. Welding in bead-onplate mode, or of an I butt joint containing no air gap joint is facilitated by using a leading torch. This is due to the preheating effect of the arc, which increases the absorptivity of the work piece to the laser beam, enabling greater penetration and the use of higher welding speeds. With an air gap present, air gap bridging is more effectively achieved by using a trailing torch because of the lower arc power needed, the wider arc, and the movement of droplets predominantly towards the joint edges. The experiments showed, that the mode of metal transfer has a marked effect on gap bridgeability. Transfer of a single droplet per arc pulse may not be desirable if an air gap is present, because most of the droplets are directed towards the middle of the joint where no base material is present. In such cases, undercut is observed. Pulsed globular and rotational metal transfer modes enable molten metal to also be transferred to the joint edges, and are therefore superior metal transfer modes when bridging air gaps. It was also found very obvious, that process separation is an important factor in gap bridgeability. If process separation is too large, the resulting weld often exhibits sagging, or no weld may be formed at all as a result of the reduced interaction between the component processes. In contrast, if the processes are too close to one another, the processing region contains excess molten metal that may create difficulties for the keyhole to remain open. When the distance is optimised - i.e. a separation of 0-4 mm in this study, depending on the welding speed and beam-arc configuration - the processes act together, creating beneficial synergistic effects. The optimum process separation when using a trailing torch was found to be shorter (0-2 mm) than when a leading torch is used (2-4 mm); a result of the facilitation of weld pool motion when the latter configuration is adopted. This study demonstrates, that the MAG process used has a strong effect on the CO2-laser-MAG hybrid welding process. The laser beam welding component is relatively stable and easy to manage, with only two principal processing parameters (power and welding speed) needing to be adjusted. In contrast, the MAG process has a large number of processing parameters to optimise, all of which play an important role in the interaction between the laser beam and the arc. The parameters used for traditional MAG welding are often not optimal in achieving the most appropriate mode of metal transfer, and weld quality in laser hybrid welding, and must be optimised if the full range of benefits provided by hybrid welding are to be realised.

Research of wood fuel market in Ukraine and the Republic of Belarus

The goal of the present work was to describe the wood fuel market of Ukraine and the Republic of Belarus, to estimate wood fuel potential and to research opportunities of wood fuel trading. Nowadays the wood waste, wood residues and by-products are becoming more and more potential raw materials for energy production. Against the background of unstable prices of traditional energy sources and environmental degradation, European States are planning to get 12% of energy from alternative sources already in 2010. Wastes of wood-working and agricultural productions are such sources. At present time the most popular wood biofuels are wood pellets, briquettes, wood chips and logs. Ukraine and the Republic of Belarus have a rather big potential of wood fuel resources. But wood fuels markets of these countries are on the entry level and quite disorganized. There is almost no domestic usage of wood biofuel. All produced pellets, briquettes as well as wood chips and logs go to the export, but the volumes are not high at present time. Ukraine and the Republic of Belarus have a very suitable geographical location. The most promising directions of wood fuel trading are developed wood fuel markets of Northern countries, Austria, Germany as well as actively developing markets of Poland and Hungary. At the long distance truck and sea transportation are the most appropriate. At a short distance cheap transportation by rail is more suitable. Thereby export is a potential opportunity for development of wood fuel production and in the future for usage in the researched countries.

The effects of real time control of welding parameters on weld quality in plasma arc keyhole welding

Joints intended for welding frequently show variations in geometry and position, for which it is unfortunately not possible to apply a single set of operating parameters to ensure constant quality. The cause of this difficulty lies in a number of factors, including inaccurate joint preparation and joint fit up, tack welds, as well as thermal distortion of the workpiece. In plasma arc keyhole welding of butt joints, deviations in the gap width may cause weld defects such as an incomplete weld bead, excessive penetration and burn through. Manual adjustment of welding parameters to compensate for variations in the gap width is very difficult, and unsatisfactory weld quality is often obtained. In this study a control system for plasma arc keyhole welding has been developed and used to study the effects of the real time control of welding parameters on gap tolerance during welding of austenitic stainless steel AISI 304L. The welding tests demonstrated the beneficial effect of real time control on weld quality. Compared with welding using constant parameters, the maximum tolerable gap width with an acceptable weld quality was 47% higher when using the real time controlled parameters for a plate thickness of 5 mm. In addition, burn through occurred with significantly larger gap widths when parameters were controlled in real time. Increased gap tolerance enables joints to be prepared and fit up less accurately, saving time and preparation costs for welding. In addition to the control system, a novel technique for back face monitoring is described in this study. The test results showed that the technique could be successfully applied for penetration monitoring when welding non magnetic materials. The results also imply that it is possible to measure the dimensions of the plasma efflux or weld root, and use this information in a feedback control system and, thus, maintain the required weld quality.

Real-Time Simulation of Mobile and Industrial Machines Using the Multibody Simulation Approach

This thesis introduces a real-time simulation environment based on the multibody simulation approach. The environment consists of components that are used in conventional product development, including computer aided drawing, visualization, dynamic simulation and finite element software architecture, data transfer and haptics. These components are combined to perform as a coupled system on one platform. The environment is used to simulate mobile and industrial machines at different stages of a product life time. Consequently, the demands of the simulated scenarios vary. In this thesis, a real-time simulation environment based on the multibody approach is used to study a reel mechanism of a paper machine and a gantry crane. These case systems are used to demonstrate the usability of the real-time simulation environment for fault detection purposes and in the context of a training simulator. In order to describe the dynamical performance of a mobile or industrial machine, the nonlinear equations of motion must be defined. In this thesis, the dynamical behaviour of machines is modelled using the multibody simulation approach. A multibody system may consist of rigid and flexible bodies which are joined using kinematic joint constraints while force components are used to describe the actuators. The strength of multibody dynamics relies upon its ability to describe nonlinearities arising from wearing of the components, friction, large rotations or contact forces in a systematic manner. For this reason, the interfaces between subsystems such as mechanics, hydraulics and control systems of the mechatronic machine can be defined and analyzed in a straightforward manner.

Influence of Heat Treatment on Strength Properties of Finger-jointed Components

The purpose for the thesis was to study the thermo treatment of finger-jointed wood. The thesis concentrated on examining the tensile and bending strength of finger-jointed and thermo treated wood. The aim was to find out how different treatment temperature levels and adhesives influence the strength of wood that has been finger-jointed before heat treatment. Secondary objectives were to examine the influence of the treatment time at one temperature, determine differences in the strength between the joints in heartwood and sapwood, examine the visual appearance of the finger joints after the treatment and establish possibilities to reach a characteristic strength level corresponding to C14. Only minor differences in strength properties were measured between the finger-jointed wood treatments II and III. A greater difference was shown between these two treatment temperatures I, which lead to reduced strength. The average strength of joints glued with adhesive 2 was higher after treatments II and III compared to those glued with the adhesive 1. At the treatment temperature I, the adhesive 1 strength properties were at the same level compared to the adhesive 2 or better. There were not any significant differences.

Usability of laser–arc hybrid welding processes in industrial applications

Metal industries producing thick sections have shown increasing interest in the laser–arc hybrid welding process because of its clear advantages compared with the individual processes of autogenous laser welding and arc welding. One major benefit of laser–arc hybrid welding is that joints with larger gaps can be welded with acceptable quality compared to autogenous laser welding. The laser-arc hybrid welding process has good potential to extend the field of applications of laser technology, and provide significant improvements in weld quality and process efficiency in manufacturing applications. The objective of this research is to present a parameter set-up for laser–arc hybrid welding processes, introduce a methodical comparison of the chosen parameters, and discuss how this technology may be adopted in industrial applications. The research describes the principles, means and applications of different types of laser–arc hybrid welding processes. Conducted experiment processing variables are presented and compared using an analytical model which can also be used for predictive simulations. The main argument in this thesis is that profound understanding of the advanced technology of laser-arc hybrid welding will help improve the productivity of welding in industrial applications. Based on a review of the current knowledge base, important areas for further research are also identified. This thesis consists of two parts. The first part introduces the research topic and discusses laser–arc hybrid welding by characterizing its mechanism and most important variables. The second part comprises four research papers elaborating on the performance of laser– arc hybrid welding in the joining of metals. The study uses quantitative and qualitative research methods which include in-depth, interpretive analyses of results from a number of research groups. In the interpretive analysis, the emphasis is placed on the relevance and usefulness of the investigative results drawn from other research publications. The results of this study contribute to research on laser–arc hybrid welding by increasing understanding of how old and new perspectives on laser–arc hybrid welding are evidenced in industry. The research methodology applied permits continued exploration of how laser–arc hybrid welding and various process factors influence the overall quality of the weld. Thestudy provides a good foundation for future research, creates improved awareness of the laser–arc hybrid welding process, and assists the metal industry to maximize welding productivity.

Modeling and Analysis of Noise and Interconnects for On-Chip Communication Link Design

This thesis considers modeling and analysis of noise and interconnects in onchip communication. Besides transistor count and speed, the capabilities of a modern design are often limited by on-chip communication links. These links typically consist of multiple interconnects that run parallel to each other for long distances between functional or memory blocks. Due to the scaling of technology, the interconnects have considerable electrical parasitics that affect their performance, power dissipation and signal integrity. Furthermore, because of electromagnetic coupling, the interconnects in the link need to be considered as an interacting group instead of as isolated signal paths. There is a need for accurate and computationally effective models in the early stages of the chip design process to assess or optimize issues affecting these interconnects. For this purpose, a set of analytical models is developed for on-chip data links in this thesis. First, a model is proposed for modeling crosstalk and intersymbol interference. The model takes into account the effects of inductance, initial states and bit sequences. Intersymbol interference is shown to affect crosstalk voltage and propagation delay depending on bus throughput and the amount of inductance. Next, a model is proposed for the switching current of a coupled bus. The model is combined with an existing model to evaluate power supply noise. The model is then applied to reduce both functional crosstalk and power supply noise caused by a bus as a trade-off with time. The proposed reduction method is shown to be effective in reducing long-range crosstalk noise. The effects of process variation on encoded signaling are then modeled. In encoded signaling, the input signals to a bus are encoded using additional signaling circuitry. The proposed model includes variation in both the signaling circuitry and in the wires to calculate the total delay variation of a bus. The model is applied to study level-encoded dual-rail and 1-of-4 signaling. In addition to regular voltage-mode and encoded voltage-mode signaling, current-mode signaling is a promising technique for global communication. A model for energy dissipation in RLC current-mode signaling is proposed in the thesis. The energy is derived separately for the driver, wire and receiver termination.