"Dov'è la sinistra?" Hemispatial neglect in stroke

As long as the incidence of stroke continues to grow, patients with large right hemisphere lesions suffering from hemispatial neglect will require neuropsychological evaluation and rehabilitation. The inability to process information especially that coming from the left side accompanied by the magnetic orientation to the ipsilesional side represents a real challenge for rehabilitation. This dissertation is concerned with crucial aspects in the clinical neuropsychological practice of hemispatial neglect. In studying the convergence of the visual and behavioural test batteries in the assessment of neglect, nine of the seventeen patients, who completed both the conventional subtests of the Behavioural Inattention Test and the Catherine Bergego Scale assessments, showed a similar severity of neglect and thus good convergence in both tests. However, patients with neglect and hemianopia had poorer scores in the line bisection test and they displayed stronger neglect in behaviour than patients with pure neglect. The second study examined, whether arm activation, modified from the Constraint Induced Movement Therapy, could be applied as neglect rehabilitation alone without any visual training. Twelve acute- or subacute patients were randomized into two rehabilitation groups: arm activation training or traditional voluntary visual scanning training. Neglect was ameliorated significantly or almost significantly in both training groups due to rehabilitation with the effect being maintained for at least six months. In studying the reflections of hemispatial neglect on visual memory, the associations of severity of neglect and visual memory performances were explored. The performances of acute and subacute patients with hemispatial neglect were compared with the performances of matched healthy control subjects. As hypothesized, encoding from the left side and immediate recall of visual material were significantly compromised in patients with neglect. Another mechanism of neglect affecting visual memory processes is observed in delayed visual reproduction. Delayed recall demands that the individual must make a match helped by a cue or it requires a search for relevant material from long-term memory storage. In the case of representational neglect, the search may succeed but the left side of the recollected memory still fails to open. Visual and auditory evoked potentials were measured in 21 patients with hemispatial neglect. Stimuli coming from the left or right were processed differently in both sensory modalities in acute and subacute patients as compared with the chronic patients. The differences equalized during the course of recovery. Recovery from hemispatial neglect was strongly associated with early rehabilitation and with the severity of neglect. Extinction was common in patients with neglect and it did not ameliorate with the recovery of neglect. The presence of pusher symptom hampered amelioration of visual neglect in acute and subacute stroke patients, whereas depression did not have any significant effect in the early phases after the stroke. However, depression had an unfavourable effect on recovery in the chronic phase. In conclusion, the combination of neglect and hemianopia may explain part of the residual behavioural neglect that is no longer evident in visual testing. Further research is needed in order to determine which specific rehabilitation procedures would be most beneficial in patients suffering the combination of neglect and hemianopia. Arm activation should be included in the rehabilitation programs of neglect; this is a useful technique for patients who need bedside treatment in the acute phase. With respect to the deficit in visual memory in association with neglect, the possible mechanisms of lateralized deficit in delayed recall need to be further examined and clarified. Intensive treatment induced recovery in both severe and moderate visual neglect long after the first two to first three months after the stroke.

Techno-Economic Feasibility of Novel On-Line Condition Monitoring Methods in Low Voltage Distribution Networks

The focus in this thesis is to study both technical and economical possibilities of novel on-line condition monitoring techniques in underground low voltage distribution cable networks. This thesis consists of literature study about fault progression mechanisms in modern low voltage cables, laboratory measurements to determine the base and restrictions of novel on-line condition monitoring methods, and economic evaluation, based on fault statistics and information gathered from Finnish distribution system operators. This thesis is closely related to master’s thesis “Channel Estimation and On-line Diagnosis of LV Distribution Cabling”, which focuses more on the actual condition monitoring methods and signal theory behind them.

DFMA Aspects in the Design of a Transfer Line for Off-line Ion Sources

In this thesis, the DFMA is presented and used for the purpose of having a design for a vertical transfer line that can be easily manufactured and assembled. The design of the transfer line, the major components and drawings are presented. The ease of assembly, the costs of manufacturing and differences between the use of steel structure and aluminum are compared. The ALARA principle is followed to minimize the risk of radiation exposure by the means of locating the test ion sources outside the radioactive area.

Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T-10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 1720 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 5080 KIAS (90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Power-line-communication-based data transmission concept for an LVDC electricity distribution network – Analysis and implementation

Communications play a key role in modern smart grids. New functionalities that make the grids ‘smart’ require the communication network to function properly. Data transmission between intelligent electric devices (IEDs) in the rectifier and the customer-end inverters (CEIs) used for power conversion is also required in the smart grid concept of the low-voltage direct current (LVDC) distribution network. Smart grid applications, such as smart metering, demand side management (DSM), and grid protection applied with communications are all installed in the LVDC system. Thus, besides remote connection to the databases of the grid operators, a local communication network in the LVDC network is needed. One solution applied to implement the communication medium in power distribution grids is power line communication (PLC). There are power cables in the distribution grids, and hence, they may be applied as a communication channel for the distribution-level data. This doctoral thesis proposes an IP-based high-frequency (HF) band PLC data transmission concept for the LVDC network. A general method to implement the Ethernet-based PLC concept between the public distribution rectifier and the customerend inverters in the LVDC grid is introduced. Low-voltage cables are studied as the communication channel in the frequency band of 100 kHz–30 MHz. The communication channel characteristics and the noise in the channel are described. All individual components in the channel are presented in detail, and a channel model, comprising models for each channel component is developed and verified by measurements. The channel noise is also studied by measurements. Theoretical signalto- noise ratio (SNR) and channel capacity analyses and practical data transmission tests are carried out to evaluate the applicability of the PLC concept against the requirements set by the smart grid applications in the LVDC system. The main results concerning the applicability of the PLC concept and its limitations are presented, and suggestion for future research proposed.

Determination of collector chemicals from flotation process waters using capillary electrophoresis

Vaahdotusprosessia käytetään yleisesti erottamaan arvokkaita mineraaleja malmeista. Toimiakseen tehokkaasti prosessi tarvitsee kokoojakemikaaleja, joiden tehtävänä on sitoa halutut mineraalit ilmakupliin. Jotta näiden kemikaalien käyttäytymistä prosessissa voitaisiin ymmärtää paremmin ja prosessin ohjausta tehostaa, pitää kokoojia pystyä analysoimaan prosessivesistä. Työn kirjallisuusosassa on koottu ja vertailtu erilaisia kirjallisuudesta löytyneitä analyysimenetelmiä kokoojakemikaaleille. Kokeellisessaosassa on kehitetty kaksi kapillaarielektroforeesimenetelmää näiden kemikaalien tutkimiseen. Menetelmien toteamisrajat tutkituille kemikaaleille olivat seuraavanlaiset: natrium diiosobutylditiofosfaattille (DTP) 2,7 mg/L puhtaassa vedessä ja 6,7 mg/L prosessivedessä; natrium diisobutyldithiofosfinaatille (DTPI) vastaavasti 4,5 mg/L ja 6,7 mg/L; etyyli ksantaatille 0,025 mg/L ja 0,16 mg/L; ja isobutyyli ksantaatille 0,41 mg/L ja 0,62 mg/L. Näitä menetelmiä voidaan tulevaisuudessa kehittää kokoojien hajoamistuotteiden analysointia varten sekä prosessien on-line mittauksiin.

The consequences of e-HRM on line managers

The purpose of this research was to provide a deeper insight into the consequences of electronic human resource management (e-HRM) for line managers. The consequences are viewed as used information system (IS) potentials pertaining to the moderate voluntaristic category of consequences. Due to the need to contextualize the research and draw on line managers’ personal experiences, a qualitative approach in a case study setting was selected. The empirical part of the research is loosely based on literature on HRM and e-HRM and it was conducted in an industrial private sector company. In this thesis, method triangulation was utilized, as nine semi-structured interviews, conducted in a European setting, created the main method for data collection and analysis. Other complementary data such as HRM documentation and statistics of e-HRM system usage were utilized as background information to help to put the results into context. E-HRM has partly been taken into use in the case study company. Line managers tend to use e-HRM when a particular task requires it, but they are not familiar with all the features and possibilities which e-HRM has to offer. The advantages of e-HRM are in line with the company’s goals. The advantages are e.g. an transparency of data, process consistency, and having an efficient and easy-to-use tool at one’s disposal. However, several unintended, even contradictory, and mainly negative outcomes can also be identified, such as over-complicated processes, in-security in use of the tool, and the lack of co-operation with HR professionals. The use of e-HRM and managers’ perceptions regarding e-HRM affect the way in which managers perceive the consequences of e-HRM on their work. Overall, the consequences of e-HRM are divergent, even contradictory. The managers who considered e-HRM mostly beneficial to their work found that e-HRM affects their work by providing information and increasing efficiency. Those managers who mostly perceived challenges in e-HRM did not think that e-HRM had affected their role or their work. Even though the perceptions regarding e-HRM and its consequences might reflect the strategies, the distribution of work, and the ways of working in all HRM in general and can’t be generalized as such, this research contributed to the field of e-HRM and it provides new perspectives to e-HRM in the case study organization and in the academic field in general.

Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T- 10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 17−20 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 50−80 KIAS (∼90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Biopolttoaineiden on-line -laadunmittauksen hyödyt energiantuotannossa

Biopolttoaineet ovat tärkeä energianlähde suomalaisessa energiantuotannossa. Biopoltto- aineille on kuitenkin ominaista laadun vaihtelevuus. Yksi tärkeimmistä laatutekijöistä on kosteus, joka vaikuttaa myös polttoaineen energiasisältöön. Laatutekijät puolestaan vai- kuttavat polttoainekäsittelyyn, polttoprosessiin ja koko laitoksen hyötysuhteeseen. Tämän työn tarkoituksena oli tutkia voisiko biopolttoaineiden online-laadunmittaus tuoda lisäarvoa energiantuotantolaitokselle. Esimerkkinä käytettiin yhtä online-laadunmittaus- sovellusta, InrayFuel-röntgenmittausjärjestelmää. Sillä voidaan seurata biopolttoaineiden kosteutta ja polttoaineen sisältämiä vierasaineita. Työssä on laadittu kustannusanalyysi, jolla pyritään selvittämään, onko nykyisen kertaluontoisen mittausmenetelmän korvaami- nen jatkuvatoimisella kannattavaa. Esimerkkilaitoksena on Etelä-Savon Energian Pur- sialan voimalaitos, jossa röntgenmittausjärjestelmään on testattu. Saatujen tulosten mukaan investoiminen esimerkkimittausjärjestelmään maksaisi itsensä takaisin alle vuodessa. Kun laitoksella pystytään seuraamaan polttoaineen laatua jatkuva- toimisesti, laadunhallinta paranee ja sitä kautta voidaan saavuttaa kustannussäästöjä. Polt- toaineesta johtuvat häiriötilanteet vähenevät, polttoaine on mahdollista optimoida edulli- semmaksi polton kannalta ja poltto-olosuhteita voidaan säätää paremmin, jolloin päästöt vähenevät ja hyötysuhde kasvaa. Työssä käytetty laskenta analysoi kuitenkin hyvin ylei- sellä tasolla, sillä käytössä ei ollut laitoksen omaa taselaskentajärjestelmää. Laskenta siis sisältää paljon oletuksia. Tämän ja rohkaisevien tulosten vuoksi tutkimusta jatkuvatoimi- sen laadunmittauksen hyödyistä kannattaa tehdä enemmän.

Reverse osmosis membrane surface modification: effects on membrane performance

The aim of this thesis was to study the surface modification of reverse osmosis membranes by surfactants and the effect of modification on rejection and flux. The surfactants included anionic and nonionic surfactants. The purpose of membrane modification was to improve pure water permeability with increasing salt rejection. The literature part of the study deals with the basic principles of reverse osmosis technology and factors affecting the membrane performance. Also the membrane surface modification by surfactants and their influence on membrane’s surface properties and efficiency (permeability and salt rejection) were discussed. In the experimental part of the thesis two thin-film composite membranes, Desal AG and LE-4040, were modified on-line with three different surfactants. The effects of process parameters (pressure, pH, and surfactant concentration) on surface modification were also examined. The characteristics of the modified membranes were determined by measuring the membranes’ contact angle and zeta potentials. The zeta potential and contact angle measurements indicate that the surfactants were adsorbed onto the both membranes. However, the adsorption did not effect on membrane’s pure water permeability and salt rejection. Thereby, the surface modification of the Desal AG and LE-4040 membranes by surfactants was not able to improve the membrane’s performance.

On-line determination of residual collector concentration in flotation process

Valuable minerals can be recovered by using froth flotation. This is a widely used separation technique in mineral processing. In a flotation cell hydrophobic particles attach on air bubbles dispersed in the slurry and rise on the top of the cell. Valuable particles are made hydrophobic by adding collector chemicals in the slurry. With the help of a frother reagent a stable froth forms on the top of the cell and the froth with valuable minerals, i.e. the concentrate, can be removed for further processing. Normally the collector is dosed on the basis of the feed rate of the flotation circuit and the head grade of the valuable metal. However, also the mineral composition of the ore affects the consumption of the collector, i.e. how much is adsorbed on the mineral surfaces. Therefore it is worth monitoring the residual collector concentration in the flotation tailings. Excess usage of collector causes unnecessary costs and may even disturb the process. In the literature part of the Master’s thesis the basics of flotation process and collector chemicals are introduced. Capillary electrophoresis (CE), an analytical technique suitable for detecting collector chemicals, is also reviewed. In the experimental part of the thesis the development of an on-line CE method for monitoring the concentration of collector chemicals in a flotation process and the results of a measurement campaign are presented. It was possible to determine the quality and quantity of collector chemicals in nickel flotation tailings at a concentrator plant with the developed on-line CE method. Sodium ethyl xanthate and sodium isopropyl xanthate residuals were found in the tailings and slight correlation between the measured concentrations and the dosage amounts could be seen.

Software product line for power converters

Työn tilaajana toimi Visedo Oy. Työn tavoitteina oli tutkia Visedo Oy:n ohjelmistokehityksen nykytila, tunnistaa seuraavat parannuskohteet ja antaa ohjeita havaittujen parannuskohteiden korjaamiseksi. Visedo Oy:n tehonmuokkain ohjelmistokehityksen nykytilaa käsiteltiin neljän valitun osa-alueen näkökulmasta: ohjelmistoarkkitehtuurityyli, komponenttipohjainen ohjelmistokehitys, ohjelmistotuotelinjojen kehitysmenetelmät ja ohjelmistovariaatioiden hallinta. Valituilla osa-alueilla havaittujen parannuskohteiden perusteella annettiin korjausehdotuksia: ohjelmistoarkkitehtuurin rakenteeseen, komponenttien jakautumiselle, komponenttien koostamiselle ja komponenttien versioinnille. Lisäksi ehdotettiin uudenlaista ohjelmistotuotelinja rakennetta, joka yhdistää kerros- ja komponenttipohjaiset arkkitehtuurityylit mahdollistaen ominaisuuksiltaan eroavien tehonmuokkain ohjelmistojen hallinnan.

Modification of commercial poly-lactide for extrusion coated food packaging applications

Poly-L-lactide (PLLA) is a widely used sustainable and biodegradable alternative to replace synthetic non-degradable plastic materials in the packaging industry. Conversely, its processing properties are not always optimal, e.g. insufficient melt strength at higher temperatures (necessary in extrusion coating processes). This thesis reports on research to improve properties of commercial PLLA grade (3051D from NatureWorks), to satisfy and extend end-use applications, such as food packaging by blending with modified PLLA. Adjustment of the processability by chain branching of commercial poly-L-lactide initiated by peroxide was evaluated. Several well-defined branched structures with four arms (sPLLA) were synthesized using pentaerythritol as a tetra-functional initiator. Finally, several block copolymers consisting of polyethylene glycol and PLLA (i.e. PEGLA) were produced to obtain a well extruded material with improved heat sealing properties. Reactive extrusion of poly-L-lactide was carried out in the presence of 0.1, 0.3 and 0.5 wt% of various peroxides [tert-butyl-peroxybenzoate (TBPB), 2,5-dimethyl-2,5-(tert-butylperoxy)-hexane (Lupersol 101; LOL1) and benzoyl peroxide (BPO)] at 190C. The peroxide-treated PLLAs showed increased complex viscosity and storage modulus at lower frequencies, indicating the formation of branched/cross linked architectures. The material property changes were dependent on the peroxide, and the used peroxide concentration. Gel fraction analysis showed that the peroxides, afforded different gel contents, and especially 0.5 wt% peroxide, produced both an extremely high molar mass, and a cross linked structure, not perhaps well suited for e.g. further use in a blending step. The thermal behavior was somewhat unexpected as the materials prepared with 0.5 wt% peroxide showed the highest ability for crystallization and cold crystallization, despite substantial cross linking. The peroxide-modified PLLA, i.e. PLLA melt extruded with 0.3 wt% of TBPB and LOL1 and 0.5 wt% BPO was added to linear PLLA in ratios of 5, 15 and 30 wt%. All blends showed increased zero shear viscosity, elastic nature (storage modulus) and shear sensitivity. All blends remained amorphous, though the ability of annealing was improved slightly. Extrusion coating on paperboard was conducted with PLLA, and peroxide-modified PLLA blends (90:10). All blends were processable, but only PLLA with 0.3 wt% of LOL1 afforded a smooth high quality surface with improved line speed. Adhesion levels between fiber and plastic, as well as heat seal performance were marginally reduced compared with pure 3051D. The water vapor transmission measurements (WVTR) of the blends containing LOL1 showed acceptable levels, only slightly lower than for comparable PLLA 3051D. A series of four-arm star-shaped poly-L-lactide (sPLLA) with different branch length was synthesized by ring opening polymerization (ROP) of L-lactide using pentaerythritol as initiator and stannous octoate as catalyst. The star-shaped polymers were further blended with its linear resin and studied for their melt flow and thermal properties. Blends containing 30 wt% of sPLLA with low molecular weight (30 wt%; Mwtotal: 2500 g mol-1 and 15000 g mol-1) showed lower zero shear viscosity and significantly increased shear thinning, while at the same time slightly increased crystallization of the blend. However, the amount of crystallization increased significantly with the higher molecular weight sPLLA, therefore the star-shaped structure may play a role as nucleating agent. PLLA-polyethylene glycol–PLLA triblock copolymers (PEGLA) with different PLLA block length were synthesized and their applicability as blends with linear PLLA (3051D NatureWorks) was investigated with the intention of improving heat-seal and adhesion properties of extrusion-coated paperboard. PLLA-PEG-PLLA was obtained by ring opening polymerization (ROP) of L-lactide using PEG (molecular weight 6000 g mol-1) as an initiator, and stannous octoate as catalyst. The structures of the PEGLAs were characterized by proton nuclear magnetic resonance spectroscopy (1H-NMR). The melt flow and thermal properties of all PEGLAs and their blends were evaluated using dynamic rheology, and differential scanning calorimeter (DSC). All blends containing 30 wt% of PEGLAs showed slightly higher zero shear viscosity, higher shear thinning and increased melt elasticity (based on tan delta). Nevertheless, no significant changes in thermal properties were distinguished. High molecular weight PEGLAs were used in extrusion coating line with 3051D without problems.

Vibration analysis of a power take-off line

Gear rattle is a phenomenon that occurs when idling or lightly loaded gears collide due to engine’s torque fluctuations. This behaviour is related to vibration behaviour of the transmission system. Aim of this master’s thesis is to evaluate Adams and Adams/Machinery as a simulation tools for modelling the rattle e ect in a transmission system. A case study of tractor’s power take-o driveline, suspected to be prone to rattle, is performed in this work. Modelling methods used by Adams in this type of study are presented in the theory section while simulation model build with the software during this work is presented in the results. The Machinery toolbox is used to create gears and bearings while other model components are created with standard Adams tool set. Geometries and excitations are exported from other softwares. Results were obtained from multiple variations of a base model. These result sets and literature review suggest that Adams/Machinery may not be the most suitable tool for rattle analysis. While the system behaviour was partially captured, for accurate modelling user-written routines must be used which may be more easily performed with other tools. Further research about this topic is required.

Post-transaction brand and model line-up integration in the automotive industry: Case studies of European companies as target of acquisitions by Chinese and Indian multinational corporations

Corporations practice company acquisitions in order to create shareholder’s value. During the last few decades, the companies in emerging markets have become active in the acquisition business. During the last decade, large and significant acquisitions have occurred especially in automotive industry. While domestic markets have become too competitive and companies are lacking required capabilities, they seek possibilities to expand into Western markets by attaining valuable assets through acquisitions of developed country corporations. This study discusses the issues and characteristics of these acquisitions through case studies. The purpose of this study was to identify the acquisition motives and strategies for post-transaction brand and product integration as well as analyze the effect of the motives to the integration strategy. The cases chosen for the research were Chinese Geely acquiring Swedish Volvo in 2010 and Indian Tata Motors buying British Jaguar Land Rover in 2008. The main topics were chosen according to their significance for companies in automotive industry as well as those are most visible parts for consumers. The study is based on qualitative case study methods, analyzing secondary data from academic papers and news articles as well as companies’ own announcements e.g. stock exchange and press releases. The study finds that the companies in the cases mainly possessed asset-seeking and market-seeking motives. In addition, the findings refer to rather minimal post-acquisition brand and product integration strategies. Mainly the parent companies left the target company autonomous to make their own business strategies and decisions. The most noticeable integrations were in the product development and production processes. Through restructuring the product architectures, the companies were able to share components and technology between product families and brands, which results in cutting down costs and in increase of profitability and efficiency. In the Geely- Volvo case, the strategy focused more on component sharing and product development know-how, whereas in Tata Motors-Jaguar Land Rover case, the main actions were to cut down costs through component sharing and combine production and distribution networks especially in Asian markets. However, it was evident that in both cases the integration and technology sharing were executed cautiously to prevent on harming the valuable image of the luxury brand. This study has concluded that the asset-seeking motives have significant influence on the posttransaction brand and model line-up integration strategies. By taking a cautious approach in acquiring assets, such as luxury brand, the companies in the cases have implemented a successful post-acquisition strategy and managed to create value for the shareholders at least in short-term. Yritykset harjoittavat yritysostoja luodakseen osakkeenomistajille lisäarvoa. Viimeisten muutamien vuosikymmenien aikana yritykset kehittyvissä maissa ovat myös aktivoituneet yritysostoissa. Viimeisen vuosikymmenen aikana erityisesti autoteollisuudessa on esiintynyt suuria ja merkittäviä yritysostoja. Koska kilpailu kotimaan markkinoilla on kiristynyt ja yritykset ovat vailla vaadittavia valmiuksia, ne etsivät mahdollisuuksiaan laajentaa länsimaisiin markkinoihin hankkimalla arvokkaita etuja kehittyneiden maiden yrityksistä yritysostojen avulla. Tämä tutkimus pohtii näiden yritysostojen olennaisia kysymyksiä ja ominaisuuksia casetutkimuksien kautta. Tutkimuksen tarkoitus oli tunnistaa sekä yritysostojen motiiveja ja brändi- ja mallisto-integraation strategioita että analysoida kyseisten motiivien vaikutusta integraatiostrategiaan. Tapaus-tutkimuksiksi valittiin kiinalaisen Geelyn yritysosto ruotsalaisesta Volvosta vuonna 2010 ja intialaisen Tata Motorsin yritysosto englantilaisesta Jaguar Land Roverista vuonna 2008. Tutkimus on kvalitatiivinen case-tutkimus ja siinä analysoidaan toissijaista tietoa sekä akateemisten ja uutisartikkeleiden että yritysten omien ilmoitusten, kuten pörssi- ja lehdistötiedotteiden, kautta. Tutkimuksen tulokset osoittavat, että tutkittujen yritysten toiminnat perustuivat motiiveihin, joita ajoivat etujen and uusien markkinoiden tarve. Sen lisäksi tutkimustulokset osoittivat, että yritysoston jälkeinen brändi- ja mallisto-integraatio pidettiin minimaalisena. Pääasiallisesti kohdeyrityksille jätettiin autonomia tehdä omat liikkeenjohdolliset päätökset yritysstrategioihin liittyen. Huomattavimmat integraatiot koskivat tuotekehityksellisiä ja tuotannollisia prosesseja. Kehittämällä uudelleen tuotearkkitehtuureja, yritykset pystyivät jakamaan komponentteja ja teknologiaa tuoteperheiden ja brändien välillä. Tämä mahdollisti kustannusleikkauksia sekä kannattavuuden ja tehokkuuden parantamista. Geely-Volvo –tapauksessa integraatiostrategia keskittyi komponenttien jakamiseen yhteisten tuotearkkitehtuurien avulla ja tuotekehityksen ammattitaitoon, kun taas Tata Motors-JLR –tapauksessa päätoiminnat olivat kustannuksien leikkaus sekä tuotannon ja jakeluverkoston yhdistäminen erityisesti Aasian maissa. Yhteistä yrityskaupoissa oli, että brändi- ja mallisto-integraatio sekä teknologian jakaminen suoritettiin varoen ehkäistäkseen arvokkaiden luksus-brändien tuotekuvan vahingoittamista. Tutkimuksen lopputulokset osoittavat, että yrityskaupan motiiveilla on huomattava vaikutus brändija mallisto-integraation strategiaan. Toteuttamalla varovaista lähestymistapaa luksus-brändin hankinnassa ja integraatiossa, yritykset ovat onnistuneet luomaan lisäarvoa osakkeenomistajille vähintään lyhyellä aikavälillä.