Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T-10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 1720 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 5080 KIAS (90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Power-line-communication-based data transmission concept for an LVDC electricity distribution network – Analysis and implementation

Communications play a key role in modern smart grids. New functionalities that make the grids ‘smart’ require the communication network to function properly. Data transmission between intelligent electric devices (IEDs) in the rectifier and the customer-end inverters (CEIs) used for power conversion is also required in the smart grid concept of the low-voltage direct current (LVDC) distribution network. Smart grid applications, such as smart metering, demand side management (DSM), and grid protection applied with communications are all installed in the LVDC system. Thus, besides remote connection to the databases of the grid operators, a local communication network in the LVDC network is needed. One solution applied to implement the communication medium in power distribution grids is power line communication (PLC). There are power cables in the distribution grids, and hence, they may be applied as a communication channel for the distribution-level data. This doctoral thesis proposes an IP-based high-frequency (HF) band PLC data transmission concept for the LVDC network. A general method to implement the Ethernet-based PLC concept between the public distribution rectifier and the customerend inverters in the LVDC grid is introduced. Low-voltage cables are studied as the communication channel in the frequency band of 100 kHz–30 MHz. The communication channel characteristics and the noise in the channel are described. All individual components in the channel are presented in detail, and a channel model, comprising models for each channel component is developed and verified by measurements. The channel noise is also studied by measurements. Theoretical signalto- noise ratio (SNR) and channel capacity analyses and practical data transmission tests are carried out to evaluate the applicability of the PLC concept against the requirements set by the smart grid applications in the LVDC system. The main results concerning the applicability of the PLC concept and its limitations are presented, and suggestion for future research proposed.

The consequences of e-HRM on line managers

The purpose of this research was to provide a deeper insight into the consequences of electronic human resource management (e-HRM) for line managers. The consequences are viewed as used information system (IS) potentials pertaining to the moderate voluntaristic category of consequences. Due to the need to contextualize the research and draw on line managers’ personal experiences, a qualitative approach in a case study setting was selected. The empirical part of the research is loosely based on literature on HRM and e-HRM and it was conducted in an industrial private sector company. In this thesis, method triangulation was utilized, as nine semi-structured interviews, conducted in a European setting, created the main method for data collection and analysis. Other complementary data such as HRM documentation and statistics of e-HRM system usage were utilized as background information to help to put the results into context. E-HRM has partly been taken into use in the case study company. Line managers tend to use e-HRM when a particular task requires it, but they are not familiar with all the features and possibilities which e-HRM has to offer. The advantages of e-HRM are in line with the company’s goals. The advantages are e.g. an transparency of data, process consistency, and having an efficient and easy-to-use tool at one’s disposal. However, several unintended, even contradictory, and mainly negative outcomes can also be identified, such as over-complicated processes, in-security in use of the tool, and the lack of co-operation with HR professionals. The use of e-HRM and managers’ perceptions regarding e-HRM affect the way in which managers perceive the consequences of e-HRM on their work. Overall, the consequences of e-HRM are divergent, even contradictory. The managers who considered e-HRM mostly beneficial to their work found that e-HRM affects their work by providing information and increasing efficiency. Those managers who mostly perceived challenges in e-HRM did not think that e-HRM had affected their role or their work. Even though the perceptions regarding e-HRM and its consequences might reflect the strategies, the distribution of work, and the ways of working in all HRM in general and can’t be generalized as such, this research contributed to the field of e-HRM and it provides new perspectives to e-HRM in the case study organization and in the academic field in general.

Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T- 10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 17−20 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 50−80 KIAS (∼90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Biopolttoaineiden on-line -laadunmittauksen hyödyt energiantuotannossa

Biopolttoaineet ovat tärkeä energianlähde suomalaisessa energiantuotannossa. Biopoltto- aineille on kuitenkin ominaista laadun vaihtelevuus. Yksi tärkeimmistä laatutekijöistä on kosteus, joka vaikuttaa myös polttoaineen energiasisältöön. Laatutekijät puolestaan vai- kuttavat polttoainekäsittelyyn, polttoprosessiin ja koko laitoksen hyötysuhteeseen. Tämän työn tarkoituksena oli tutkia voisiko biopolttoaineiden online-laadunmittaus tuoda lisäarvoa energiantuotantolaitokselle. Esimerkkinä käytettiin yhtä online-laadunmittaus- sovellusta, InrayFuel-röntgenmittausjärjestelmää. Sillä voidaan seurata biopolttoaineiden kosteutta ja polttoaineen sisältämiä vierasaineita. Työssä on laadittu kustannusanalyysi, jolla pyritään selvittämään, onko nykyisen kertaluontoisen mittausmenetelmän korvaami- nen jatkuvatoimisella kannattavaa. Esimerkkilaitoksena on Etelä-Savon Energian Pur- sialan voimalaitos, jossa röntgenmittausjärjestelmään on testattu. Saatujen tulosten mukaan investoiminen esimerkkimittausjärjestelmään maksaisi itsensä takaisin alle vuodessa. Kun laitoksella pystytään seuraamaan polttoaineen laatua jatkuva- toimisesti, laadunhallinta paranee ja sitä kautta voidaan saavuttaa kustannussäästöjä. Polt- toaineesta johtuvat häiriötilanteet vähenevät, polttoaine on mahdollista optimoida edulli- semmaksi polton kannalta ja poltto-olosuhteita voidaan säätää paremmin, jolloin päästöt vähenevät ja hyötysuhde kasvaa. Työssä käytetty laskenta analysoi kuitenkin hyvin ylei- sellä tasolla, sillä käytössä ei ollut laitoksen omaa taselaskentajärjestelmää. Laskenta siis sisältää paljon oletuksia. Tämän ja rohkaisevien tulosten vuoksi tutkimusta jatkuvatoimi- sen laadunmittauksen hyödyistä kannattaa tehdä enemmän.

On-line determination of residual collector concentration in flotation process

Valuable minerals can be recovered by using froth flotation. This is a widely used separation technique in mineral processing. In a flotation cell hydrophobic particles attach on air bubbles dispersed in the slurry and rise on the top of the cell. Valuable particles are made hydrophobic by adding collector chemicals in the slurry. With the help of a frother reagent a stable froth forms on the top of the cell and the froth with valuable minerals, i.e. the concentrate, can be removed for further processing. Normally the collector is dosed on the basis of the feed rate of the flotation circuit and the head grade of the valuable metal. However, also the mineral composition of the ore affects the consumption of the collector, i.e. how much is adsorbed on the mineral surfaces. Therefore it is worth monitoring the residual collector concentration in the flotation tailings. Excess usage of collector causes unnecessary costs and may even disturb the process. In the literature part of the Master’s thesis the basics of flotation process and collector chemicals are introduced. Capillary electrophoresis (CE), an analytical technique suitable for detecting collector chemicals, is also reviewed. In the experimental part of the thesis the development of an on-line CE method for monitoring the concentration of collector chemicals in a flotation process and the results of a measurement campaign are presented. It was possible to determine the quality and quantity of collector chemicals in nickel flotation tailings at a concentrator plant with the developed on-line CE method. Sodium ethyl xanthate and sodium isopropyl xanthate residuals were found in the tailings and slight correlation between the measured concentrations and the dosage amounts could be seen.

Software product line for power converters

Työn tilaajana toimi Visedo Oy. Työn tavoitteina oli tutkia Visedo Oy:n ohjelmistokehityksen nykytila, tunnistaa seuraavat parannuskohteet ja antaa ohjeita havaittujen parannuskohteiden korjaamiseksi. Visedo Oy:n tehonmuokkain ohjelmistokehityksen nykytilaa käsiteltiin neljän valitun osa-alueen näkökulmasta: ohjelmistoarkkitehtuurityyli, komponenttipohjainen ohjelmistokehitys, ohjelmistotuotelinjojen kehitysmenetelmät ja ohjelmistovariaatioiden hallinta. Valituilla osa-alueilla havaittujen parannuskohteiden perusteella annettiin korjausehdotuksia: ohjelmistoarkkitehtuurin rakenteeseen, komponenttien jakautumiselle, komponenttien koostamiselle ja komponenttien versioinnille. Lisäksi ehdotettiin uudenlaista ohjelmistotuotelinja rakennetta, joka yhdistää kerros- ja komponenttipohjaiset arkkitehtuurityylit mahdollistaen ominaisuuksiltaan eroavien tehonmuokkain ohjelmistojen hallinnan.

Vibration analysis of a power take-off line

Gear rattle is a phenomenon that occurs when idling or lightly loaded gears collide due to engine’s torque fluctuations. This behaviour is related to vibration behaviour of the transmission system. Aim of this master’s thesis is to evaluate Adams and Adams/Machinery as a simulation tools for modelling the rattle e ect in a transmission system. A case study of tractor’s power take-o driveline, suspected to be prone to rattle, is performed in this work. Modelling methods used by Adams in this type of study are presented in the theory section while simulation model build with the software during this work is presented in the results. The Machinery toolbox is used to create gears and bearings while other model components are created with standard Adams tool set. Geometries and excitations are exported from other softwares. Results were obtained from multiple variations of a base model. These result sets and literature review suggest that Adams/Machinery may not be the most suitable tool for rattle analysis. While the system behaviour was partially captured, for accurate modelling user-written routines must be used which may be more easily performed with other tools. Further research about this topic is required.

Post-transaction brand and model line-up integration in the automotive industry: Case studies of European companies as target of acquisitions by Chinese and Indian multinational corporations

Corporations practice company acquisitions in order to create shareholder’s value. During the last few decades, the companies in emerging markets have become active in the acquisition business. During the last decade, large and significant acquisitions have occurred especially in automotive industry. While domestic markets have become too competitive and companies are lacking required capabilities, they seek possibilities to expand into Western markets by attaining valuable assets through acquisitions of developed country corporations. This study discusses the issues and characteristics of these acquisitions through case studies. The purpose of this study was to identify the acquisition motives and strategies for post-transaction brand and product integration as well as analyze the effect of the motives to the integration strategy. The cases chosen for the research were Chinese Geely acquiring Swedish Volvo in 2010 and Indian Tata Motors buying British Jaguar Land Rover in 2008. The main topics were chosen according to their significance for companies in automotive industry as well as those are most visible parts for consumers. The study is based on qualitative case study methods, analyzing secondary data from academic papers and news articles as well as companies’ own announcements e.g. stock exchange and press releases. The study finds that the companies in the cases mainly possessed asset-seeking and market-seeking motives. In addition, the findings refer to rather minimal post-acquisition brand and product integration strategies. Mainly the parent companies left the target company autonomous to make their own business strategies and decisions. The most noticeable integrations were in the product development and production processes. Through restructuring the product architectures, the companies were able to share components and technology between product families and brands, which results in cutting down costs and in increase of profitability and efficiency. In the Geely- Volvo case, the strategy focused more on component sharing and product development know-how, whereas in Tata Motors-Jaguar Land Rover case, the main actions were to cut down costs through component sharing and combine production and distribution networks especially in Asian markets. However, it was evident that in both cases the integration and technology sharing were executed cautiously to prevent on harming the valuable image of the luxury brand. This study has concluded that the asset-seeking motives have significant influence on the posttransaction brand and model line-up integration strategies. By taking a cautious approach in acquiring assets, such as luxury brand, the companies in the cases have implemented a successful post-acquisition strategy and managed to create value for the shareholders at least in short-term. Yritykset harjoittavat yritysostoja luodakseen osakkeenomistajille lisäarvoa. Viimeisten muutamien vuosikymmenien aikana yritykset kehittyvissä maissa ovat myös aktivoituneet yritysostoissa. Viimeisen vuosikymmenen aikana erityisesti autoteollisuudessa on esiintynyt suuria ja merkittäviä yritysostoja. Koska kilpailu kotimaan markkinoilla on kiristynyt ja yritykset ovat vailla vaadittavia valmiuksia, ne etsivät mahdollisuuksiaan laajentaa länsimaisiin markkinoihin hankkimalla arvokkaita etuja kehittyneiden maiden yrityksistä yritysostojen avulla. Tämä tutkimus pohtii näiden yritysostojen olennaisia kysymyksiä ja ominaisuuksia casetutkimuksien kautta. Tutkimuksen tarkoitus oli tunnistaa sekä yritysostojen motiiveja ja brändi- ja mallisto-integraation strategioita että analysoida kyseisten motiivien vaikutusta integraatiostrategiaan. Tapaus-tutkimuksiksi valittiin kiinalaisen Geelyn yritysosto ruotsalaisesta Volvosta vuonna 2010 ja intialaisen Tata Motorsin yritysosto englantilaisesta Jaguar Land Roverista vuonna 2008. Tutkimus on kvalitatiivinen case-tutkimus ja siinä analysoidaan toissijaista tietoa sekä akateemisten ja uutisartikkeleiden että yritysten omien ilmoitusten, kuten pörssi- ja lehdistötiedotteiden, kautta. Tutkimuksen tulokset osoittavat, että tutkittujen yritysten toiminnat perustuivat motiiveihin, joita ajoivat etujen and uusien markkinoiden tarve. Sen lisäksi tutkimustulokset osoittivat, että yritysoston jälkeinen brändi- ja mallisto-integraatio pidettiin minimaalisena. Pääasiallisesti kohdeyrityksille jätettiin autonomia tehdä omat liikkeenjohdolliset päätökset yritysstrategioihin liittyen. Huomattavimmat integraatiot koskivat tuotekehityksellisiä ja tuotannollisia prosesseja. Kehittämällä uudelleen tuotearkkitehtuureja, yritykset pystyivät jakamaan komponentteja ja teknologiaa tuoteperheiden ja brändien välillä. Tämä mahdollisti kustannusleikkauksia sekä kannattavuuden ja tehokkuuden parantamista. Geely-Volvo –tapauksessa integraatiostrategia keskittyi komponenttien jakamiseen yhteisten tuotearkkitehtuurien avulla ja tuotekehityksen ammattitaitoon, kun taas Tata Motors-JLR –tapauksessa päätoiminnat olivat kustannuksien leikkaus sekä tuotannon ja jakeluverkoston yhdistäminen erityisesti Aasian maissa. Yhteistä yrityskaupoissa oli, että brändi- ja mallisto-integraatio sekä teknologian jakaminen suoritettiin varoen ehkäistäkseen arvokkaiden luksus-brändien tuotekuvan vahingoittamista. Tutkimuksen lopputulokset osoittavat, että yrityskaupan motiiveilla on huomattava vaikutus brändija mallisto-integraation strategiaan. Toteuttamalla varovaista lähestymistapaa luksus-brändin hankinnassa ja integraatiossa, yritykset ovat onnistuneet luomaan lisäarvoa osakkeenomistajille vähintään lyhyellä aikavälillä.

Control of a line robot system with Embedded Linux

Many, if not all, aspects of our everyday lives are related to computers and control. Microprocessors and wireless communications are involved in our lives. Embedded systems are an attracting field because they combine three key factors, small size, low power consumption and high computing capabilities. The aim of this thesis is to study how Linux communicates with the hardware, to answer the question if it is possible to use an operating system like Debian for embedded systems and finally, to build a Mechatronic real time application. In the thesis a presentation of Linux and the Xenomai real time patch is given, the bootloader and communication with the hardware is analyzed. BeagleBone the evaluation board is presented along with the application project consisted of a robot cart with a driver circuit, a line sensor reading a black line and two Xbee antennas. It makes use of Xenomai threads, the real time kernel. According to the obtained results, Linux is able to operate as a real time operating system. The issue of future research is the area of embedded Linux is also discussed.

Evaluation of the Efficiency of Line-Start Permanent-Magnet Machines as a Function of the Operating Temperature

The standard squirrel-cage induction machine has nearly reached its maximum efficiency. In order to further increase the energy efficiency of electrical machines, the use of permanent magnets in combination with the robust design and the line start capability of the induction machine is extensively investigated. Many experimental designs have been suggested in literature, but recently, these line-start permanent-magnet machines (LSPMMs) have become off-the-shelf products available in a power range up to 7.5 kW. The permanent magnet flux density is a function of the operating temperature. Consequently, the temperature will affect almost every electrical quantity of the machine, including current, torque, and efficiency. In this paper, the efficiency of an off-the-shelf 4-kW three-phase LSPMM is evaluated as a function of the temperature by both finite-element modeling and by practical measurements. In order to obtain stator, rotor, and permanent magnet temperatures, lumped thermal modeling is used.