Centralized Motion Control of a Linear Tooth Belt Drive: Analysis of the Performance and Limitations

A centralized robust position control for an electrical driven tooth belt drive is designed in this doctoral thesis. Both a cascaded control structure and a PID based position controller are discussed. The performance and the limitations of the system are analyzed and design principles for the mechanical structure and the control design are given. These design principles are also suitable for most of the motion control applications, where mechanical resonance frequencies and control loop delays are present. One of the major challenges in the design of a controller for machinery applications is that the values of the parameters in the system model (parameter uncertainty) or the system model it self (non-parametric uncertainty) are seldom known accurately in advance. In this thesis a systematic analysis of the parameter uncertainty of the linear tooth beltdrive model is presented and the effect of the variation of a single parameter on the performance of the total system is shown. The total variation of the model parameters is taken into account in the control design phase using a Quantitative Feedback Theory (QFT). The thesis also introduces a new method to analyze reference feedforward controllers applying the QFT. The performance of the designed controllers is verified by experimentalmeasurements. The measurements confirm the control design principles that are given in this thesis.

Design and analysis of a transversal-flux switched-reluctance-linear-machine pole-pair

The Switched Reluctance technology is probably best suited for industrial low-speed or zerospeed applications where the power can be small but the torque or the force in linear movement cases might be relatively high. Because of its simple structure the SR-motor is an interesting alternative for low power applications where pneumatic or hydraulic linear drives are to be avoided. This study analyses the basic parts of an LSR-motor which are the two mover poles and one stator pole and which form the “basic pole pair” in linear-movement transversal-flux switchedreluctance motors. The static properties of the basic pole pair are modelled and the basic design rules are derived. The models developed are validated with experiments. A one-sided one-polepair transversal-flux switched-reluctance-linear-motor prototype is demonstrated and its static properties are measured. The modelling of the static properties is performed with FEM-calculations. Two-dimensional models are accurate enough to model the static key features for the basic dimensioning of LSRmotors. Three-dimensional models must be used in order to get the most accurate calculation results of the static traction force production. The developed dimensioning and modelling methods, which could be systematically validated by laboratory measurements, are the most significant contributions of this thesis.

Towards input/output-free modelling of linear infinite-dimensional systems in continuous time

This dissertation describes a networking approach to infinite-dimensional systems theory, where there is a minimal distinction between inputs and outputs. We introduce and study two closely related classes of systems, namely the state/signal systems and the port-Hamiltonian systems, and describe how they relate to each other. Some basic theory for these two classes of systems and the interconnections of such systems is provided. The main emphasis lies on passive and conservative systems, and the theoretical concepts are illustrated using the example of a lossless transfer line. Much remains to be done in this field and we point to some directions for future studies as well.

GAMS MINLP Solver comparisons and some improvements to the AlphaECP algorithm

I doktorsavhandlingen undersöks förmågan att lösa hos ett antal lösare för optimeringsproblem och ett antal svårigheter med att göra en rättvis lösarjämförelse avslöjas. Dessutom framläggs några förbättringar som utförts på en av lösarna som heter GAMS/AlphaECP. Optimering innebär, i det här sammanhanget, att finna den bästa möjliga lösningen på ett problem. Den undersökta klassen av problem kan karaktäriseras som svårlöst och förekommer inom ett flertal industriområden. Målet har varit att undersöka om det finns en lösare som är universellt snabbare och hittar lösningar med högre kvalitet än någon av de andra lösarna. Det kommersiella optimeringssystemet GAMS (General Algebraic Modeling System) och omfattande problembibliotek har använts för att jämföra lösare. Förbättringarna som presenterats har utförts på GAMS/AlphaECP lösaren som baserar sig på skärplansmetoden Extended Cutting Plane (ECP). ECP-metoden har utvecklats främst av professor Tapio Westerlund på Anläggnings- och systemteknik vid Åbo Akademi.

Generic Life Cycle Cost Model and Cost-effective Solutions

Life cycle costing (LCC) practices are spreading from military and construction sectors to wider area of industries. Suppliers as well as customers are demanding comprehensive cost knowledge that includes all relevant cost elements through the life cycle of products. The problem of total cost visibility is being acknowledged and the performance of suppliers is evaluated not just by low acquisition costs of their products, but by total value provided through the life time of their offerings. The main purpose of this thesis is to provide better understanding of product cost structure to the case company. Moreover, comprehensive theoretical body serves as a guideline or methodology for further LCC process. Research includes the constructive analysis of LCC related concepts and features as well as overview of life cycle support services in manufacturing industry. The case study aims to review the existing LCC practices within the case company and provide suggestions for improvements. It includes identification of most relevant life cycle cost elements, development of cost breakdown structure and generic cost model for data collection. Moreover, certain cost-effective suggestions are provided as well. This research should support decision making processes, assessment of economic viability of products, financial planning, sales and other processes within the case company.

Effective Message Design and Media Mix of Senior Mobile Phone in China

The present research focuses on the study of how to design message and select media in advertising to generate customer’s purchase intention towards senior mobile phone in China. The message design concentrates mainly on message framing and fear appeals study while the media selection method is only based on direct matching. For exploring the main research question, the study utilized qualitative methodology. The data collection consisted of a pre-interview questionnaire, interviews, and three sets of experiments. The experiments were designed to test the selected 18 participants’ responses toward different emotional appeals and message framings. The findings illustrate participants’ understanding of senior mobile phone and their media usage habits. Moreover, positive message framing and emotional appeals in advertising are more effective. Gender differences in responding to emotional appeals were explored as well.

Fatigue study of the fillet weld waving on weld toe and the penetration in the weld root based on the effective notch stress approach

The fatigue failure of structures under fluctuating loads in fillet weld joints raises a demand to determine the parameters related to this type of loading. In this study, the stress distribution in the susceptible area of weld toe and weld root in fillet welded models analyzed by finite element method applying FEMAP software. To avoid the geometrical singularity on the path of analytical stress analysis in the toe and root area of a weld model the effective notch stress approach applied by which a proper fictitious rounding that mostly depend on the material of structure is applied. The models with different weld toe waving width and radius are analyzed while the flank angle of weld varied in 45 and 30 degrees. The processed results shows that the waving compare to the straight weld toe makes differences in the value of stress and consequently the stress concentration factor between the tip and depth of the waves in the weld toe which helps to protect the crack of propagation and gives enough time and tools to be informed of the crack initiation in the structure during the periodical observation of structure. In the weld root study the analyses among the models with the welding penetration percentage from non-penetration to the full-penetration shows a slightly increase in the root area stress value which comparing with the stiffening effect of penetration conclude that the half-penetration can make an optimization between the stress increase and stiffening effect of deep penetration.

Eri laskentamenetelmien vertailu hitsatun rakenteen väsymislaskennassa

Tässä työssä tutkittiin eri mitoitusmenetelmien soveltuvuutta hitsattujen rakenteiden vä-symislaskennassa. Käytetyt menetelmät olivat rakenteellinen jännityksen menetelmä, te-hollisen lovijännityksen menetelmä ja murtumismekaniikka. Lisäksi rakenteellisen jänni-tyksen määrittämiseksi käytettiin kolmea eri menetelmää. Menetelmät olivat pintaa pitkin ekstrapolointi, paksuuden yli linearisointi ja Dongin menetelmä. Väsymiskestävyys määritettiin kahdelle hitsiliitoksen yksityiskohdalle. Laskenta tehtiin käyttäen elementtimenetelmää rakenteen 3D-mallille. Tutkittavasta aggregaattirungosta oli olemassa FE-malli mutta alimallinnustekniikkaa hyödyntämällä pystyttiin yksityiskohtai-semmin tutkimaan vain pientä osaa koko rungon mallista. Rakenteellisen jännityksen menetelmä perustuu nimellisiin jännityksiin. Kyseinen mene-telmä ei vaadi geometrian muokkausta. Yleensä rakenteellisen jännityksen menetelmää käytetään hitsin rajaviivan väsymislaskennassa, mutta joissain tapauksissa sitä on käytetty juuren puolen laskennassa. Tässä työssä rakenteellisen jännityksen menetelmää käytettiin myös juuren puolen tutkimisessa. Tehollista lovijännitystä tutkitaan mallintamalla 1 mm fiktiiviset pyöristykset sekä rajaviivalle että juuren puolelle. Murtumismekaniikan so-veltuvuutta tutkittiin käyttämällä Franc2D särön kasvun simulointiohjelmaa. Väsymislaskennan tulokset eivät merkittävästi poikkea eri laskentamenetelmien välillä. Ainoastaan rakenteellisen jännityksen Dongin menetelmällä saadaan poikkeavia tuloksia. Tämä johtuu pääasiassa siitä, että menetelmän laskentaetäisyydestä ei ole tietoa. Raken-teellisen jännityksen menetelmällä, tehollisen lovijännityksen menetelmällä ja murtumis-mekaniikalla saadaan samansuuntaiset tulokset. Suurin ero menetelmien välillä on mal-linnuksen ja laskennan vaatima työmäärä.

Acidic dissolution of iron oxides and regeneration of a ceramic filter medium

The dewatering of iron ore concentrates requires large capacity in addition to producing a cake with low moisture content. Such large processes are commonly energy intensive and means to lower the specific energy consumption are needed. Ceramic capillary action disc filters incorporate a novel filter medium enabling the harnessing of capillary action, which results in decreased energy consumption in comparison to traditional filtration technologies. As another benefit, the filter medium is mechanically and chemically more durable than, for example, filter cloths and can, thus, withstand harsh operating conditions and possible regeneration better than other types of filter media. In iron ore dewatering, the regeneration of the filter medium is done through a combination of several techniques: (1) backwashing, (2) ultrasonic cleaning, and (3) acid regeneration. Although it is commonly acknowledged that the filter medium is affected by slurry particles and extraneous compounds, published research, especially in the field of dewatering of mineral concentrates, is scarce. Whereas the regenerative effect of backwashing and ultrasound are more or less mechanical, regeneration with acids is based on chemistry. The chemistry behind the acid regeneration is, naturally, dissolution. The dissolution of iron oxide particles has been extensively studied over several decades but those studies may not necessarily be directly applicable in the regeneration of the filter medium which has undergone interactions with the slurry components. The aim of this thesis was to investigate if free particle dissolution indeed correlates with the regeneration of the filter medium. For this purpose, both free particle dissolution and dissolution of surface adhered particles were studied. The focus was on acidic dissolution of iron oxide particles and on the study of the ceramic filter medium used in the dewatering of iron ore concentrates. The free particle dissolution experiments show that the solubility of synthetic fine grained iron oxide particles in oxalic acid could be explained through linear models accounting for the effects of temperature and acid concentration, whereas the dissolution of a natural magnetite is not so easily explained by such models. In addition, the kinetic experiments performed both support and contradict the work of previous authors: the suitable kinetic model here supports previous research suggesting solid state reduction to be the reaction mechanism of hematite dissolution but the formation of a stable iron oxalate is not supported by the results of this research. Several other dissolution mechanisms have also been suggested for iron oxide dissolution in oxalic acid, indicating that the details of oxalate promoted reductive dissolution are not yet agreed and, in this respect, this research offers added value to the community. The results of the regeneration experiments with the ceramic filter media show that oxalic acid is highly effective in removing iron oxide particles from the surface of the filter medium. The dissolution of those particles did not, however, exhibit the expected behaviour, i.e. complete dissolution. The results of this thesis show that although the regeneration of the ceramic filter medium with acids incorporates the dissolution of slurry particles from the surface of the filter medium, the regeneration cannot be assessed purely based upon free particle dissolution. A steady state, dependent on temperature and on the acid concentration, was observed in the dissolution of particles from the surface even though the limit of solubility of free iron oxide particles had not been reached. Both the regeneration capacity and efficiency, with regards to the removal of iron oxide particles, was found to be temperature dependent, but was not affected by the acid concentration. This observation further suggests that the removal of the surface adhered particles does not follow the dissolution of free particles, which do exhibit a dependency on the acid concentration. In addition, changes in the permeability and in the pore structure of the filter medium were still observed after the bulk concentration of dissolved iron had reached a steady state. Consequently, the regeneration of the filter medium continued after the dissolution of particles from the surface had ceased. This observation suggests that internal changes take place at the final stages of regeneration. The regeneration process could, in theory, be divided into two, possibly overlapping, stages: (1) dissolution of surface-adhered particles, and (2) dissolution of extraneous compounds from within the pore structure. In addition to the fundamental knowledge generated during this thesis, tools to assess the effects of parameters on the regeneration of the ceramic filter medium are needed. It has become clear that the same tools used to estimate the dissolution of free particles cannot be used to estimate the regeneration of a filter medium unless only a robust characterisation of the order of regeneration efficiency is needed.

Effective Social Intranet. Case: Mobile Routing Business Unit, Tellabs

The purpose of this thesis is to examine what the normative, effective social Intranet solution is for Tellabs Mobile Routing business unit in terms of sharing knowledge more openly and effectively, fostering innovation, and improving team spirit and positive employee experience. Additionally, these aspects are researched from the intra- and inter-organizational points of view. The research is based on previous literature and empirical interviews. Based on these two items, an eight-fold recommendation proposal was created to change the current Intranet to become an effective social Intranet.

FE-analyysin soveltaminen S960 QC teräksisen I-profiilin äärikestävyyden määrittämisessä

Tässä työssä tutkittiin FE-analyysin soveltamista S960 QC teräksisen I-profiilin kestävyyden määrittämisessä. Työn tavoitteena oli tarkastella nykyisten suunnitteluohjeiden soveltuvuutta ultralujille teräksille ja koota ohjemateriaali I-profiilin optimoimisesta sekä FE-analyysin hyö-dyntämisestä I-profiilin staattisen ja dynaamisen kestävyyden määrittämisessä. I-profiili mitoitettiin ja optimoitiin Eurokoodi 3:ssa esitettyjen PL3 mukaisten mitoitusohjeiden avulla. Rakenteelle suoritettiin Eurokoodi 3:n ja IIW:n mukaiset lommahdus-, kiepahdus- ja vä-symiskestävyystarkastelut. Väsymistarkastelussa sovellettiin nimellisen jännityksen, rakenteelli-sen jännityksen ja tehollisen lovijännityksen menetelmiä sekä murtumismekaniikkaa. Rakenteel-lisen jännityksen menetelmässä sovellettiin lisäksi lineaarista ja parabolista pintaa pitkin ekstra-polointia, paksuuden yli linearisointia sekä Dong:in menetelmää. Lommahdus-, kiepahdus- ja väsymistarkasteluissa hyödynnettiin analyyttistä laskentaa, FE-analyysiä sekä Frank2d sovellusta. Tarkastelujen perusteella voidaan todeta, että analyyttisillä menetelmillä saadaan numeerisia me-netelmiä varmemmalla puolella olevia tuloksia. Lommahdustarkastelussa ero tulosten välillä on suurimmillaan 8 % ja kiepahdustarkastelussa suurimmillaan 20 % mutta väsymistarkastelussa saadut tulokset eroavat keskenään huomattavasti. Väsymistarkastelussa tehollisen lovijännityksen menetelmällä sekä rakenteellisen jännityksen menetelmän Dong:in menetelmällä saadaan huo-mattavasti muita menetelmiä pidempiä kestoikiä, kun taas yksinkertaisemmilla menetelmillä saa-dut kestoiät ovat lyhyempiä. Rakenteen kestävyyden määrittäminen analyyttisillä menetelmillä on melko helppoa, mutta tu-lokset ovat monesti liian konservatiivisia. FE-analyysillä saadaan puolestaan hyvin tarkkoja tu-loksia mallin ollessa yksityiskohtainen. Mallintaminen on kuitenkin aikaa ja resursseja vievää ja vaatii käyttökokemusta. FE-analyysin mahdolliset hyödyt on aina arvioitava tapauskohtaisesti tarkasteltavan geometrian, kuormitusten ja reunaehtojen perusteella.

Roles of leadership in complex environments : Enhancing Knowledge Flows in Organisational Constellations through Practice-Based Innovation Processes

Global challenges, complexity and continuous uncertainty demand development of leadership approaches, employees and multi-organisation constellations. Current leadership theories do not sufficiently address the needs of complex business environments. First of all, before successful leadership models can be applied in practice, leadership needs to shift from the industrial age to the knowledge era. Many leadership models still view leadership solely through the perspective of linear process thinking. In addition, there is not enough knowledge or experience in applying these newer models in practice. Leadership theories continue to be based on the assumption that leaders possess or have access to all the relevant knowledge and capabilities to decide future directions without external advice. In many companies, however, the workforce consists of skilled professionals whose work and related interfaces are so challenging that the leaders cannot grasp all the linked viewpoints and cross-impacts alone. One of the main objectives of this study is to understand how to support participants in organisations and their stakeholders to, through practice-based innovation processes, confront various environments. Another aim is to find effective ways of recognising and reacting to diverse contexts, so companies and other stakeholders are better able to link to knowledge flows and shared value creation processes in advancing joint value to their customers. The main research question of this dissertation is, then, to seek understanding of how to enhance leadership in complex environments. The dissertation can, on the whole, be characterised as a qualitative multiple-case study. The research questions and objectives were investigated through six studies published in international scientific journals. The main methods applied were interviews, action research and a survey. The empirical focus was on Finnish companies, and the research questions were examined in various organisations at the top levels (leaders and managers) and bottom levels (employees) in the context of collaboration between organisations and cooperation between case companies and their client organisations. However, the emphasis of the analysis is the internal and external aspects of organisations, which are conducted in practice-based innovation processes. The results of this study suggest that the Cynefin framework, complexity leadership theory and transformational leadership represent theoretical models applicable to developing leadership through practice-based innovation. In and of themselves, they all support confronting contemporary challenges, but an implementable method for organisations may be constructed by assimilating them into practice-based innovation processes. Recognition of diverse environments, their various contexts and roles in the activities and collaboration of organisations and their interest groups is ever-more important to achieving better interaction in which a strategic or formal status may be bypassed. In innovation processes, it is not necessarily the leader who is in possession of the essential knowledge; thus, it is the role of leadership to offer methods and arenas where different actors may generate advances. Enabling and supporting continuous interaction and integrated knowledge flows is of crucial importance, to achieve emergence of innovations in the activities of organisations and various forms of collaboration. The main contribution of this dissertation relates to applying these new conceptual models in practice. Empirical evidence on the relevance of different leadership roles in practice-based innovation processes in Finnish companies is another valuable contribution. Finally, the dissertation sheds light on the significance of combining complexity science with leadership and innovation theories in research.

Viilunkuivaajan tuotantotehokkuuden kehittäminen

Mekaanisen metsäteollisuuden tuotteiden kiristyvä globaali kilpailu ja jatkuva kustannusten kasvaminen kiristyvillä markkinoilla aiheuttavat jatkuvaa tuotannon tehostamisen tarvetta. Käyntiaikojen maksimoinnilla ja tuotantokoneiden käyttöasteen nostamisella haetaan hintaetua sekä toimituskapasiteetin maksimointia kilpailussa asiakkaista myös tulevaisuutta silmälläpitäen. Vanerin tuotantoprosessiin osaprosessina kuuluva viilun kuivaus on tehtaan tuotannon pullonkaula. Kuivauskoneen tuotannollisten häiriöiden syiden selvittämisillä ja käyntiajan lisäämisellä on suora tuotannollinen vaikutus. Tutkimuksessa löydettiin mahdollisia parannuskohteita tuotantolaitteisiin. Käsiteltävän aiheen ollessa aiemmin kirjallisuudessa käsittelemätön, jouduttiin kehitys- ja parannustoimenpiteissä tekemään suoraviivaisia syy- ja seuraussuhteisiin perustuvia ratkaisuja. Vaihtoehdoista etsittiin toiminnaltaan mahdollisimman yksinkertaisia sekä hankinta- ja käyttökustannuksiltaan kustannustehokkaita ratkaisuja.