VVER-440 Thermal Hydraulics as a Computer Code Validation Challenge

This thesis concentrates on the validation of a generic thermal hydraulic computer code TRACE under the challenges of the VVER-440 reactor type. The code capability to model the VVER-440 geometry and thermal hydraulic phenomena specific to this reactor design has been examined and demonstrated acceptable. The main challenge in VVER-440 thermal hydraulics appeared in the modelling of the horizontal steam generator. The major challenge here is not in the code physics or numerics but in the formulation of a representative nodalization structure. Another VVER-440 specialty, the hot leg loop seals, challenges the system codes functionally in general, but proved readily representable. Computer code models have to be validated against experiments to achieve confidence in code models. When new computer code is to be used for nuclear power plant safety analysis, it must first be validated against a large variety of different experiments. The validation process has to cover both the code itself and the code input. Uncertainties of different nature are identified in the different phases of the validation procedure and can even be quantified. This thesis presents a novel approach to the input model validation and uncertainty evaluation in the different stages of the computer code validation procedure. This thesis also demonstrates that in the safety analysis, there are inevitably significant uncertainties that are not statistically quantifiable; they need to be and can be addressed by other, less simplistic means, ultimately relying on the competence of the analysts and the capability of the community to support the experimental verification of analytical assumptions. This method completes essentially the commonly used uncertainty assessment methods, which are usually conducted using only statistical methods.

Safety and outcome of coronary interventions with special reference to anticoagulation and stent type

University of Turku, Faculty of Medicine, Department of Cardiology and Cardiovascular Medicine, Doctoral Programme of Clinical Investigation, Heart Center, Turku University Hospital, Turku, Finland Division of Internal Medicine, Department of Cardiology, Seinäjoki Central Hospital, Seinäjoki, Finland Heart Center, Satakunta Central Hospital, Pori, Finland Annales Universitatis Turkuensis Painosalama Oy, Turku, Finland 2015 Antithrombotic therapy during and after coronary procedures always entails the challenging establishment of a balance between bleeding and thrombotic complications. It has been generally recommended to patients on long-term warfarin therapy to discontinue warfarin a few days prior to elective coronary angiography or intervention to prevent bleeding complications. Bridging therapy with heparin is recommended for patients at an increased risk of thromboembolism who require the interruption of anticoagulation for elective surgery or an invasive procedure. In study I, consecutive patients on warfarin therapy referred for diagnostic coronary angiography were compared to control patients with a similar disease presentation without warfarin. The strategy of performing coronary angiography during uninterrupted therapeutic warfarin anticoagulation appeared to be a relatively safe alternative to bridging therapy, if the international normalized ratio level was not on a supratherapeutic level. In-stent restenosis remains an important reason for failure of long-term success after a percutaneous coronary intervention (PCI). Drug-eluting stents (DES) reduce the problem of restenosis inherent to bare metal stents (BMS). However, a longer delay in arterial healing may extend the risk of stent thrombosis (ST) far beyond 30 days after the DES implantation. Early discontinuation of antiplatelet therapy has been the most important predisposing factor for ST. In study II, patients on long-term oral anticoagulant (OAC) underwent DES or BMS stenting with a median of 3.5 years’follow-up. The selective use of DESs with a short triple therapy seemed to be safe in OAC patients, since late STs were rare even without long clopidogrel treatment. Major bleeding and cardiac events were common in this patient group irrespective of stent type. In order to help to predict the bleeding risk in patients on OAC, several different bleeding risk scorings have been developed. Risk scoring systems have also been used also in the setting of patients undergoing a PCI. In study III, the predictive value of an outpatient bleeding risk index (OBRI) to identify patients at high risk of bleeding was analysed. The bleeding risk seemed not to modify periprocedural or long-term treatment choices in patients on OAC after a percutaneous coronary intervention. Patients with a high OBRI often had major bleeding episodes, and the OBRI may be suitable for risk evaluation in this patient group. Optical coherence tomography (OCT) is a novel technology for imaging intravascular coronary arteries. OCT is a light-based imaging modality that enables a 12–18 µm tissue axial resolution to visualize plaques in the vessel, possible dissections and thrombi as well as, stent strut appositions and coverage, and to measure the vessel lumen and lesions. In study IV, 30 days after titanium-nitride-oxide (TITANOX)-coated stent implantation, the binary stent strut coverage was satisfactory and the prevalence of malapposed struts was low as evaluated by OCT. Long-term clinical events in patients treated with (TITANOX)-coated bio-active stents (BAS) and paclitaxel-eluting stents (PES) in routine clinical practice were examined in study V. At the 3-year follow-up, BAS resulted in better long-term outcome when compared with PES with an infrequent need for target vessel revascularization. Keywords: anticoagulation, restenosis, thrombosis, bleeding, optical coherence tomography, titanium

Electrical Safety of Island Operated Low Voltage DC Network

Today, renewable energy technologies and modern power electronics have made it feasible to implement low voltage direct current (LVDC) microgrids (MGs) ca-pable to island operation. Such LVDC networks are particularly useful in remote areas. However, there are still pending issues in island operated LVDC MGs like electrical safety and controlled operation, which should be addressed before wide-scale implementation. This thesis is focused on the overall protection of an island operated LVDC network concept, including protection against electrical shocks, mains equipment protection and protection of photovoltaic (PV) power sources and battery energy storage systems (BESSs). The topic is approached through ex-amination of the safety hazards and the appropriate methods to protect against them, comprising considerations for earthing system selection and realisation of the protection system.

Accelerating food safety and quality control: The use of antibody engineering techniques in the detec-tion of low-molecular weight food contaminants

The increased awareness and evolved consumer habits have set more demanding standards for the quality and safety control of food products. The production of foodstuffs which fulfill these standards can be hampered by different low-molecular weight contaminants. Such compounds can consist of, for example residues of antibiotics in animal use or mycotoxins. The extremely small size of the compounds has hindered the development of analytical methods suitable for routine use, and the methods currently in use require expensive instrumentation and qualified personnel to operate them. There is a need for new, cost-efficient and simple assay concepts which can be used for field testing and are capable of processing large sample quantities rapidly. Immunoassays have been considered as the golden standard for such rapid on-site screening methods. The introduction of directed antibody engineering and in vitro display technologies has facilitated the development of novel antibody based methods for the detection of low-molecular weight food contaminants. The primary aim of this study was to generate and engineer antibodies against low-molecular weight compounds found in various foodstuffs. The three antigen groups selected as targets of antibody development cause food safety and quality defects in wide range of products: 1) fluoroquinolones: a family of synthetic broad-spectrum antibacterial drugs used to treat wide range of human and animal infections, 2) deoxynivalenol: type B trichothecene mycotoxin, a widely recognized problem for crops and animal feeds globally, and 3) skatole, or 3-methyindole is one of the two compounds responsible for boar taint, found in the meat of monogastric animals. This study describes the generation and engineering of antibodies with versatile binding properties against low-molecular weight food contaminants, and the consecutive development of immunoassays for the detection of the respective compounds.

Development and Effect Analysis of the Asteri Consultative Auditing Process - Safety and Security Management in Educational Institutions

The Finnish legislation requires for a safe and secure learning environment. However, the comprehensive, risk based safety and security management (SSM) and the management commitment in the implementation and development of the SSM are not mentioned in the legislation. Multiple institutions, operators and researchers have studied and developed safety and security in educational institutions over the past decade. Typically the approach has been fragmented and without bringing up the importance of the comprehensive SSM. The development needs of the safety and security operations in universities have been studied. However, in universities of applied sciences (UASs) and in elementary schools (ESs), the performance level, strengths and weaknesses of the comprehensive SSM have not been studied. The objective of this study was to develop the comprehensive, risk based SSM of educational institutions by developing the new Asteri consultative auditing process and study its effects on auditees. Furthermore, the performance level in the comprehensive SSM in UASs and ESs were studied using Asteri and the TUTOR model developed by the Keski-Uusimaa Department for Rescue Services. In addition, strengths, development needs and differences were identified. In total, 76 educational institutions were audited between the years 2011 and 2014. The study is based on logical empiricism, and an observational applied research design was used. Auditing, observation and an electronic survey were used for data collection. Statistical analysis was used to analyze the collected information. In addition, thematic analysis was used to analyze the development areas of the organizations mentioned by the respondents in the survey. As one of the main contributions, this research presents the new Asteri consultative auditing process. Organizations with low performance levels on the audited subject benefit the most from the Asteri consultative auditing process. Asteri may be usable in many different types of audits, not only in SSM audits. As a new result, this study provides new knowledge on attitudes related to auditing. According to the research findings, auditing may generate negative attitudes and the auditor should take them into account when planning and preparing for audits. Negative attitudes can be compensated by producing added value, objectivity and positivity for the audit and, thus, improve the positive effects of auditing on knowledge and skills. Moreover, as the results of this study shows, auditing safety and security issues do not increase feelings of insecurity, but rather increase feelings of safety and security when using the new Asteri consultative auditing process with the TUTOR model. The results showed that the SSM in the audited UASs was statistically significantly more advanced than that in the audited ESs. However, there is still room for improvement in the ESs and the UASs as the approach to the SSM was fragmented. It can be assumed that the majority of Finnish UASs and ESs do not likely meet the basic level of the comprehensive, risk based the SSM.

Failure modes of passive decay heat removing safety systems of modern nuclear power plants

The purpose of this master’s thesis is to gain an understanding of passive safety systems’ role in modern nuclear reactors projects and to research the failure modes of passive decay heat removal safety systems which use phenomenon of natural circulation. Another purpose is to identify the main physical principles and phenomena which are used to establish passive safety tools in nuclear power plants. The work describes passive decay heat removal systems used in AES-2006 project and focuses on the behavior of SPOT PG system. The descriptions of the main large-scale research facilities of the passive safety systems of the AES-2006 power plant are also included. The work contains the calculations of the SPOT PG system, which was modeled with thermal-hydraulic system code TRACE. The dimensions of the calculation model are set according to the dimensions of the real SPOT PG system. In these calculations three parameters are investigated as a function of decay heat power: the pressure of the system, the natural circulation mass flow rate around the closed loop, and the level of liquid in the downcomer. The purpose of the calculations is to test the ability of the SPOT PG system to remove the decay heat from the primary side of the nuclear reactor in case of failure of one, two, or three loops out of four. The calculations show that three loops of the SPOT PG system have adequate capacity to provide the necessary level of safety. In conclusion, the work supports the view that passive systems could be widely spread in modern nuclear projects.

Finnish Maritime Personnel's Conceptions on Safety Management and Safety Culture

The purpose of this thesis is to explore Finnish maritime personnel’s conceptions of safety management and its relationship with the concept of safety culture. In addition, the aim is to evaluate the impact of the ISM Code on the prevailing safety culture in the Finnish shipping business. A total of 94 interviewees and seven Finnish shipping companies were involved in this study. Thematic interviews were applied as the main research method for the study. The results were analysed qualitatively. The results indicate that maritime safety culture can simultaneously demonstrate features of integration, differentiation and ambiguity. Basically, maritime personnel have a positive attitude towards safety management systems since they consider safety management beneficial and essential in general. However, the study also found considerable criticism among the interviewees. The interviewed maritime personnel did not criticise the ISM Code as such, yet they criticised the way the ISM Code has been applied in practise. In order to understand the multiple perspectives of safety culture more comprehensively, multiple theoretical perspectives and methodological approaches are needed. This study indicates that safety culture and the impacts of the ISM Code should not be unambiguously studied solely quantitative methods or qualitative methods. By examining safety culture from several methodological and theoretical perspectives, one may gain a more versatile and holistic overview of safety culture.