Modeling reaction kinetics and mass transfer in ozonation in water solutions

This dissertation is based on four articles dealing with modeling of ozonation. The literature part of this considers some models for hydrodynamics in bubble column simulation. A literature review of methods for obtaining mass transfer coefficients is presented. The methods presented to obtain mass transfer are general models and can be applied to any gas-liquid system. Ozonation reaction models and methods for obtaining stoichiometric coefficients and reaction rate coefficients for ozonation reactions are discussed in the final section of the literature part. In the first article, ozone gas-liquid mass transfer into water in a bubble column was investigated for different pH values. A more general method for estimation of mass transfer and Henry’s coefficient was developed from the Beltrán method. The ozone volumetric mass transfer coefficient and the Henry’s coefficient were determined simultaneously by parameter estimation using a nonlinear optimization method. A minor dependence of the Henry’s law constant on pH was detected at the pH range 4 - 9. In the second article, a new method using the axial dispersion model for estimation of ozone self-decomposition kinetics in a semi-batch bubble column reactor was developed. The reaction rate coefficients for literature equations of ozone decomposition and the gas phase dispersion coefficient were estimated and compared with the literature data. The reaction order in the pH range 7-10 with respect to ozone 1.12 and 0.51 the hydroxyl ion were obtained, which is in good agreement with literature. The model parameters were determined by parameter estimation using a nonlinear optimization method. Sensitivity analysis was conducted using object function method to obtain information about the reliability and identifiability of the estimated parameters. In the third article, the reaction rate coefficients and the stoichiometric coefficients in the reaction of ozone with the model component p-nitrophenol were estimated at low pH of water using nonlinear optimization. A novel method for estimation of multireaction model parameters in ozonation was developed. In this method the concentration of unknown intermediate compounds is presented as a residual COD (chemical oxygen demand) calculated from the measured COD and the theoretical COD for the known species. The decomposition rate of p-nitrophenol on the pathway producing hydroquinone was found to be about two times faster than the p-nitrophenol decomposition rate on the pathway producing 4- nitrocatechol. In the fourth article, the reaction kinetics of p-nitrophenol ozonation was studied in a bubble column at pH 2. Using the new reaction kinetic model presented in the previous article, the reaction kinetic parameters, rate coefficients, and stoichiometric coefficients as well as the mass transfer coefficient were estimated with nonlinear estimation. The decomposition rate of pnitrophenol was found to be equal both on the pathway producing hydroquinone and on the path way producing 4-nitrocathecol. Comparison of the rate coefficients with the case at initial pH 5 indicates that the p-nitrophenol degradation producing 4- nitrocathecol is more selective towards molecular ozone than the reaction producing hydroquinone. The identifiability and reliability of the estimated parameters were analyzed with the Marcov chain Monte Carlo (MCMC) method. @All rights reserved. No part of the publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior permission of the author.

Highly functional binding surface for miniaturised solid-phase immunoassays. - A spot story -

Several bioaffinity assays are based on the detection of an analyte which is bound on a solid substrate via biochemical interaction. These so called solid phase assays are based on the adhesion of the primary binding partner on a solid surface, which then binds the analyte to be detected. In this thesis work a novel solid phase based assay technology, known as spot technology, was developed. The spot technology is based on combination of high-capacity solid phases, concentrated in a spot format, utilising modified streptavidin molecules and recombinant antibody fragments. The reduction of the solid phase binding surface to a size of a spot enabled denser binding of the target molecules, providing improved signal intensities and signal-to-background ratio when applied in different solid phase immunoassays. Streptavidin-biotin interactions are commonly utilised in numerous different bioaffinity assays and the ultimate nature of streptavidin to bind biotin is among the strongest non-covalent interaction reported between two biomolecules. In this study native core streptavidin was chemically modified to provide polymerised streptavidin molecules with altered adsorption properties. These streptavidin conjugates, when coated onto polystyrene surface, provided enhanced biotin binding capacity and surface stability when compared to a reference coating constructed with native streptavidin. Furthermore, the combination of chemically modified streptavidin, sitespecifically biotinylated antibody fragments and the spot coating technology provided highly dense solid phase coating with improved binding properties. The performance of the spot assay technology was further demonstrated in different immunoassay configurations. Human thyroid stimulating hormone (TSH) and human cardiac troponin I (cTnI) were used as model analytes to show the applicability of the highly sensitive spot-based solid-phase immunoassay for detection of very low levels of analytes. It was demonstrated that the spot technology provided an assay concept with enhanced sensitivity and short turn-around times, characteristics that are highly suitable for point-of-care applications.

Improving the Potentials of Logistics Processes: Identification and Solutions

The importance of logistics for companies is a well known and justified issue. Today, enterprises are developing their logistics processes in order to match their products and services to the requirements of the most important customers. Therefore there is a need for developing analysing tools for logistics and especially for analysing the significance of various customer service elements. The aim of this paper is to propose analytic tools for supporting strategic level logistics decision making by emphasizing service level elements on two levels: (1) to introduce and propose approaches to categorize the developing efforts of logistics and (2) to introduce and/or propose approaches for solving some customer service related strategic level logistics problems. This study consists of two parts. In the first part an overview of the work is presented, and the second part comprises eight research papers on the topic of the study. The overview includes an introduction, where strategic and tactical level logistics problems are discussed and the relation of logistics to marketing and customer service issues is presented. In the first part of the study the objectives, the structure, the research strategy and the contribution of the research are described, and the challenges for future research are discussed. In the second part the three first papers deal with the identification of objectives for logistics while the remaining five papaers concentrate on solving customer service related strategic level logistics problems.

Teollisten palveluiden tarjoajien ja asiakkaan välisen yhteistyösuhteen kehittäminen

Työssä tutkitaan asennetun laitekannan kunnossapitopalveluun perustuvan yritysten välisen yhteistyösuhteen kehittämisen edellytyksiä. Tutkimus pohjautuu teollisten palveluiden, yritysten välisten yhteistyösuhteiden ja palveluiden kehittämisen osatekijöiden ja menestystekijöiden teoreettiseen tarkasteluun, sekä kohdeyrityksille suoritetun kvalitatiivisen haastattelututkimuksen tulosten analysointiin teoreettisen viitekehyksen valossa. Tavoitteena on muodostaa ehjä ja hallittava kokonaisuus monialaisen ongelmakentän kriittisistä osatekijöistä, sekä niiden keskinäisistä kausaliteeteista. Yritysten välisen yhteistyön lähtökohtana on, että kaikki yhteistyön osapuolet saavuttavat toiminnalla hyötyjä omasta näkökulmastaan tarkasteltuna. Yhteistyösuhteen kehittäminen ja yhteisen arvon toteutuminen edellyttää näin ollen, että tarjottavan palvelukokonaisuuden sisältämät potentiaaliset hyödyt ja toisaalta myös niitä vastaavat riskit ymmärretään sekä palveluntarjoajan että asiakkaan organisaatiossa. Yhteistyösuhteen kehittäminen edellyttää edelleen myös, että suhteen kehittymistä ja saavutettavia hyötyjä pystytään mittaamaan relevanttien mittareiden avulla. Tutkimuksessa keskitytään hyötypotentiaalin selvittämisen edellytyksiin, sekä hyötyjen viestimisen haasteisiin molempia osapuolia palvelevasta objektiivisesta näkökulmasta. Haastattelututkimuksessa havaittujen ongelmakohtien pohjalta eritellään kehityskohteita ja ratkaisuehdotuksia päätöksenteon tueksi sekä laajojen palvelukokonaisuuksien ja niihin liittyvän ongelmakentän hahmottamisen ja hallinnan helpottamiseksi.

Happaman hydrometallurgisen PLS-liuoksen puhdistaminen kiintoaineesta kalvosuodatustekniikalla

Tässä diplomityössä tutkittiin keraamisten mikrosuodatuskalvojen soveltuvuutta kiintoaineen erottamiseen happamasta PLS-liuoksesta eri huokoskoon omaavilla mikrosuodatuskalvoilla. Koelaitteistolla suodatettiin puhdasta vettä, kaoliinipitoista vesiliuosta sekä hapanta kuparia, kalsiumia ja kaoliinia sisältävää malliliuosta. Koeajojen tavoitteena oli saada tietoa permeaattivuon maksimimäärästä eri mikrosuodatuskalvoilla sekä tuotteen puhtaudesta. Näiden lisäksi saatiin tietoa kalvojen likaantumisesta ajon aikana. Teoriaosassa käsiteltiin yleisesti kalvosuodatusta, esitettiin yleiset kalvotekniset menetelmät ja sovellukset sekä käytiin läpi tutkimuksia samankaltaisiin kalvoihin ja sovelluksiin liittyen. Lisäksi teoriaosuudessa pohdittiin mahdollisuutta käyttää myös muita, kuin putkimoduulisia mikrosuodatuskalvoja. Myös työhön oleellisena taustana kuuluvaa hydrometallurgiaa tarkasteltiin teoreettiselta kannalta. Puhtaan veden suodatuskoetuloksista havaittiin, että kaikki kalvot jäivät selvästi valmistajan ilmoittamista arvoista. 1,0 µm CoMetas CoMem® kalvon teoreettinen vesivuo on 10 m3/(h bar) ja 3,0 µm CoMetas CoMem® teoreettinen vesivuo on yli 50 m3/(h bar). Näistä parhaimman vuon arvon sai 1,0 µm CoMetas CoMem® mikrosuodatuskalvo. Tämä kalvo oli paras sekä veden suodatuksissa että malliliuoksella tehdyillä suodatuksilla. Malliliuoksella saavutettiin n. 2000 L/(m2 h) paineen ollessa 2,0 bar ja virtausnopeuden ollessa 4,4 m/s. Vastaavat vesiajon tulokset olivat n. 1100 L/(m2 h) paineen ollessa 1,0 bar ja virtausnopeuden 2,9 m/s. Kaikki kolme käytettyä kalvoa pidättivät kaoliiniliuoksen 81–100 %:sesti. Kuparipitoista malliliuosta suodatettaessa pystyttiin vastaavasti erottamaan 77–99 % kiintoaineesta. Koeajoissa kuitenkin havaittiin huomattava vuon arvojen putoaminen, joka johtui kalvon likaantumisesta. Huomioitavaa oli kuitenkin, että hapanta malliliuosta suodatettaessa permeaattivuon arvot olivat kaoliiniliuoksen suodatuksessa saatuja vastaavia arvoja korkeammat.

Chelating Adsorbents in Purification of Hydrometallurgical Solutions

In this thesis, equilibrium and dynamic sorption properties of weakly basic chelating adsorbents were studied to explain removal of copper, nickel from a concentrated zinc sulfate solution in a hydrometallurgical process. Silica-supported chelating composites containing either branched poly(ethyleneimine) (BPEI) or 2-(aminomethyl)pyridine (AMP) as a functional group were used. The adsorbents are commercially available from Purity Systems Inc, USA as WP-1® and CuWRAM®, respectively. The fundamental interactions between the adsorbents, sulfuric acid and metal sulfates were studied in detail and the results were used to find the best conditions for removal of copper and nickel from an authentic ZnSO4 process solution. In particular, the effect of acid concentration and temperature on the separation efficiency was considered. Both experimental and modeling aspectswere covered in all cases. Metal sorption is considerably affected by the chemical properties of the studied adsorbents and by the separation conditions. In the case of WP-1, acid affinity is so high that column separation of copper, nickel and zinc has to be done using the adsorbent in base-form. On the other hand, the basicity of CuWRAM is significantly lower and protonated adsorbent can be used. Increasing temperature decreases the basicity and the metals affinity of both adsorbents, but the uptake capacities remain practically unchanged. Moreover, increasing temperature substantially enhances intra-particle mass transport and decreases viscosities thus allowing significantly higher feed flow rates in the fixed-bed separation. The copper selectivity of both adsorbents is very high even in the presence of a 250-fold excess of zinc. However, because of the basicity of WP-1, metal precipitation is a serious problem and therefore only CuWRAM is suitable for the practical industrial application. The optimum temperature for copper removal appears to be around 60 oC and an alternative solution purification method is proposed. The Ni/Zn selectivity of both WP-1 and CuWRAM is insufficient for removal of the very small amounts of nickel present in the concentrated ZnSO4 solution.

Managing the Pricing of Integrated Solutions in Export Partnerships

Little research has been conducted to guide the management of marketing variables, such as pricing, in systems business context. Furthermore, given that international partnering has become a popular mode of operation for SMEs, the objective of the current thesis was to explore the scantly researched topic of managing the pricing of integrated solutions in an export partnership. Specifically, the thesis synthesizes literature findings from the three areas of export pricing, systems business, and export partnerships. The empirical section of the study consists of a qualitative single-case study of a Finnish systems integrator that has recently launched its export operations. Primary data was collected by conducting four interviews of the case company’s managers and by organizing one group interview session. The study findings indicate that a systems integrator’s pricing strategy in an export partnership can be very multidimensional and dependant on international pricing environment and partner characteristics, that an export partnership appears to have unique implications on a systems integrator’s pricing process, and that customer value –based pricing strategies might be particularly suited to pricing integrated solutions.

Novel Robot Solutions for Carrying out Field Joint Welding and Machining in the Assembly of the Vacuum Vessel of ITER

It is necessary to use highly specialized robots in ITER (International Thermonuclear Experimental Reactor) both in the manufacturing and maintenance of the reactor due to a demanding environment. The sectors of the ITER vacuum vessel (VV) require more stringent tolerances than normally expected for the size of the structure involved. VV consists of nine sectors that are to be welded together. The vacuum vessel has a toroidal chamber structure. The task of the designed robot is to carry the welding apparatus along a path with a stringent tolerance during the assembly operation. In addition to the initial vacuum vessel assembly, after a limited running period, sectors need to be replaced for repair. Mechanisms with closed-loop kinematic chains are used in the design of robots in this work. One version is a purely parallel manipulator and another is a hybrid manipulator where the parallel and serial structures are combined. Traditional industrial robots that generally have the links actuated in series are inherently not very rigid and have poor dynamic performance in high speed and high dynamic loading conditions. Compared with open chain manipulators, parallel manipulators have high stiffness, high accuracy and a high force/torque capacity in a reduced workspace. Parallel manipulators have a mechanical architecture where all of the links are connected to the base and to the end-effector of the robot. The purpose of this thesis is to develop special parallel robots for the assembly, machining and repairing of the VV of the ITER. The process of the assembly and machining of the vacuum vessel needs a special robot. By studying the structure of the vacuum vessel, two novel parallel robots were designed and built; they have six and ten degrees of freedom driven by hydraulic cylinders and electrical servo motors. Kinematic models for the proposed robots were defined and two prototypes built. Experiments for machine cutting and laser welding with the 6-DOF robot were carried out. It was demonstrated that the parallel robots are capable of holding all necessary machining tools and welding end-effectors in all positions accurately and stably inside the vacuum vessel sector. The kinematic models appeared to be complex especially in the case of the 10-DOF robot because of its redundant structure. Multibody dynamics simulations were carried out, ensuring sufficient stiffness during the robot motion. The entire design and testing processes of the robots appeared to be complex tasks due to the high specialization of the manufacturing technology needed in the ITER reactor, while the results demonstrate the applicability of the proposed solutions quite well. The results offer not only devices but also a methodology for the assembly and repair of ITER by means of parallel robots.

Biopolttoaineiden lisäämismahdollisuudet kaukolämmön tuotannossa pienen kokoluokan tuotantolaitoksissa Lahden seudulla

Tämä diplomityö on tehty IMMU-hankkeeseen, jossa selvitetään konkreettisia keinoja ilmastonmuutoksen hillintään Lahden seudulla. Diplomityössä tarkastellaan mahdollisuuksia lisätä biopolttoaineita pienen kokoluokan kaukolämmön tuotantolaitoksissa. Teoria osuuden pohjalta luodaan skenaariot Nastolaan ja Vääksyyn (Asikkala). Skenaarioissa tarkastellaan biopolttoaineiden lisäämisen vaikutuksia kasvihuonekaasu- ja hiukkaspäästöihin käyttämällä elinkaariarviointimenetelmää. Taloudellisia seikkoja tarkastellaan laskemalla takaisinmaksuaikoja eri biolaitosratkaisuille nettonykyarvomenetelmällä. Tutkimuksen tuloksena saatiin, että kasvihuonekaasupäästöt tuotannon elinkaaren ajalta vähenevät eniten tuottamalla kaukolämmön perustuotanto Nastolassa ja Vääksyssä bio-CHP-laitoksella haketta polttamalla. Kiinteitä biopolttoaineita poltettaessa tulevat kuitenkin suurimmat hiukkaspäästöt, mikä vaikuttaa asuinympäristön viihtyvyyteen tuotantolaitoksen läheisyydessä. Bio-CHP-laitoksen investointikustannukset ovat suurimmat ja takaisinmaksuaika pisin. Nastolan kulutusperusteisiä päästöjä pystytään vähentämään eniten investoimalla biolämpölaitokseen tai bio-CHP-laitokseen. Päästöjä Nastolassa pystyttäisiin kyseisillä investoinneilla vähentämään enimmillään 6,4 %. Lahti energian kokonaispäästöjä pystyttäisiin enimmillään vähentämään noin 1,6 %. Johtopäätöksenä tutkimuksesta voidaan sanoa, että kasvihuonekaasupäästöjä pystytään vähentämään investointien avulla. Toiset ratkaisut ovat vain kalliimpia kuin toiset. Lisäksi kiinteitä biopolttoaineita käytettäessä jotkut poltto-ominaisuudet voivat heiketä esim. verrattuna maakaasun polttoon. Biopolttoaineiden lisäämisellä kuitenkin päästään irti riippuvuudesta fossiilisiin polttoaineisiin kuten öljyyn ja maakaasuun. Investointeja tehdessä on vaikea sanoa suoraan, mikä vaihtoehto on paras tapa tuottaa kaukolämpöä. Investointipäätöksiä tehdessä päätökseen vaikuttaa se, mitä tuotannon ominaispiirteitä painotetaan eniten.