Influence of Travelling Current Linkage Harmonics on Inductance Variation, Torque Ripple and Sensorless Capability of Tooth-Coil Permanent-Magnet Synchronous Machines

This paper introduces an important source of torque ripple in PMSMs with tooth-coil windings (TC-PMSMs). It is theoretically proven that saturation and cross-saturation phenomena caused by the non-synchronous harmonics of the stator current linkage cause a synchronous inductance variation with a particular periodicity. This, in turn, determines the magnitude of the torque ripple and can also deteriorate the performance of signal-injection-based rotor position estimation algorithms. An improved dq- inductance model is proposed. It can be used in torque ripple reduction control schemes and can enhance the self-sensing capabilities of TC-PMSMs

Permanent magnet synchronous generator design solution for large directdrive wind turbines: Thermal behavior of the LC DD-PMSG

Wind is one of the most compelling forms of indirect solar energy. Available now, the conversion of wind power into electricity is and will continue to be an important element of energy self-sufficiency planning. This paper is one in a series intended to report on the development of a new type of generator for wind energy; a compact, high-power, direct-drive permanent magnet synchronous generator (DD-PMSG) that uses direct liquid cooling (LC) of the stator windings to manage Joule heating losses. The main param-eters of the subject LC DD-PMSG are 8 MW, 3.3 kV, and 11 Hz. The stator winding is cooled directly by deionized water, which flows through the continuous hollow conductor of each stator tooth-coil winding. The design of the machine is to a large degree subordinate to the use of these solid-copper tooth-coils. Both steady-state and timedependent temperature distributions for LC DD-PMSG were examined with calculations based on a lumpedparameter thermal model, which makes it possible to account for uneven heat loss distribution in the stator conductors and the conductor cooling system. Transient calculations reveal the copper winding temperature distribution for an example duty cycle during variable-speed wind turbine operation. The cooling performance of the liquid cooled tooth-coil design was predicted via finite element analysis. An instrumented cooling loop featuring a pair of LC tooth-coils embedded in a lamination stack was built and laboratory tested to verify the analytical model. Predicted and measured results were in agreement, confirming the predicted satisfactory operation of the LC DD-PMSG cooling technology approach as a whole.

Heat-transfer improvements in an axial-flux permanent-magnet synchronous machine

Axial-flux machines tend to have cooling difficulties since it is difficult to arrange continuous heat path between the stator stack and the frame. One important reason for this is that no shrink fitting of the stator is possible in an axial-flux machine. Using of liquid-cooled end shields does not alone solve this issue. Cooling of the rotor and the end windings may also be difficult at least in case of two-stator-single-rotor construction where air circulation in the rotor and in the end-winding areas may be difficult to arrange. If the rotor has significant losses air circulation via the rotor and behind the stator yokes should be arranged which, again, weakens the stator cooling. In this paper we study a novel way of using copper bars as extra heat transfer paths between the stator teeth and liquid cooling pools in the end shields. After this the end windings still suffer of low thermal conductivity and means for improving this by high-heat-conductance material was also studied. The design principle of each cooling system is presented in details. Thermal models based on Computational Fluid Dynamics (CFD) are used to analyse the temperature distribution in the machine. Measurement results are provided from different versions of the machine. The results show that significant improvements in the cooling can be gained by these steps.

Study of a vapor-compression air-conditioning system for jetliners

Most modern passenger aeroplanes use air cycle cooling. A high-speed air cycle is a reliable and light option, but not very efficient. This thesis presents research work done to design a novel vapour cooling cycle for aeroplanes. Due to advancements in high-speed permanent magnet motors, the vapour cycle is seen as a competitive option for the air cycle in aeroplanes. The aerospace industry places tighter demands on the weight, reliability and environmental effects of the machinery than those met by conventional chillers, and thus modifications to conventional design are needed. The thesis is divided into four parts: the initial screening of the working fluid, 1-D design and performance values of the compressor, 1-D off-design value predictions of the compressor and the 3-D design of the compressor. The R245fa was selected as the working fluid based the study. The off-design range of the compressor was predicted to be wide and suitable for the application. The air-conditioning system developed is considerably smaller than previous designs using centrifugal compressors.

Analysis of torque and speed ripple producing non-idealities of frequency converters in electric drives

Electric motors driven by adjustable-frequency converters may produce periodic excitation forces that can cause torque and speed ripple. Interaction with the driven mechanical system may cause undesirable vibrations that affect the system performance and lifetime. Direct drives in sensitive applications, such as elevators or paper machines, emphasize the importance of smooth torque production. This thesis analyses the non-idealities of frequencyconverters that produce speed and torque ripple in electric drives. The origin of low order harmonics in speed and torque is examined. It is shown how different current measurement error types affect the torque. As the application environment, direct torque control (DTC) method is applied to permanent magnet synchronous machines (PMSM). A simulation model to analyse the effect of the frequency converter non-idealities on the performance of the electric drives is created. Themodel enables to identify potential problems causing torque vibrations and possibly damaging oscillations in electrically driven machine systems. The model is capable of coupling with separate simulation software of complex mechanical loads. Furthermore, the simulation model of the frequency converter's control algorithm can be applied to control a real frequency converter. A commercial frequencyconverter with standard software, a permanent magnet axial flux synchronous motor and a DC motor as the load are used to detect the effect of current measurement errors on load torque. A method to reduce the speed and torque ripple by compensating the current measurement errors is introduced. The method is based on analysing the amplitude of a selected harmonic component of speed as a function oftime and selecting a suitable compensation alternative for the current error. The speed can be either measured or estimated, so the compensation method is applicable also for speed sensorless drives. The proposed compensation method is tested with a laboratory drive, which consists of commercial frequency converter hardware with self-made software and a prototype PMSM. The speed and torque rippleof the test drive are reduced by applying the compensation method. In addition to the direct torque controlled PMSM drives, the compensation method can also beapplied to other motor types and control methods.

Sähköisen lineaariservomoottorijärjestelmän dynamiikan simulointi

Työssä johdettiin sähköisen lineaariservomoottorijärjestelmän dynaaminen malli. Lineaarimoottori on keksintönä vanha, mutta vasta viimeaikoina kestomagneettimateriaalien kehittyessä ja halvetessa lineaarimoottorista on tullut varteenotettava vaihtoehto pyörivän moottorin ja lineaarisen liikkeen toteuttavan mekanismin yhdistelmälle. Kestomagnetoituja lineaarimoottoreita käytetään sovelluksissa, joissa tarvitaan tarkkaa paikoitusta ja nopeudella ja kiihtyvyydellä on suuret vaatimukset. Moottorimalli toteutettiin vuorovaikutteisena simulointimallina. Moottorimalli, josta saatiin moottorin voima, rakennettiin MatLabâ 6.0/Simulinkâ –ohjelmalle ja moottoriin kiinnitetyn mekaniikan malli ADAMS 10.0 –ohjelmalle. Mallit on liitetty tämän jälkeen vuorovaikutteiseksi simulointimalliksi. Simuloinnista saatuja tuloksia on verrattu koneautomaation laboratorioon hankitun lineaarimoottorijärjestelmän mitattuihin vasteisiin.

Kestomagneettitahtikonekäytön soveltaminen paperiteollisuuden linjakäytöissä

Tässä työssä tutkitaan kestomagneettitahtimoottorin soveltuvuutta paperiteollisuuden linjakäyttöihin. Aluksi perehdytään taajuusohjatun kestomagneettitahtimoottorin häviöiden syntymiseen ja niiden jakautumiseen. Työssä esitellään kestomagneettitahtimoottorin koon valintaan vaikuttavia tekijöitä ja vertaillaan oikosulkumoottorin ja kestomagneettitahtimoottorin mitoituksen eroja. Lisäksi tarkasteltiin linjakäytön vaihtosuuntaajan ja syöttöryhmän mitoitusta, kun kestomagneettitahtimoottoria käytetään paperiteollisuuden linjakäytössä. Kestomagneettitahtimoottorin virran riippuvuutta kuormituksesta laskettiin ja mitattiin yhden kestomagneettitahtimoottorin virta eri kuormituksilla. Näin voitiin suorittaa vertailu laskennan ja todellisuuden välillä. Mittaus osoitti laskentatavan tarkkuuden. Selvityksessä löydettiin riittävän tarkka laskentatapa, jonka avulla voidaan määrittää linjakäytön invertterin koko.

Reluktanssiverkkomalli kestomagneettitahtikoneen staattisen ilmavälivuontiheyden mallinnukseen

Kaikissa pyörivissä sähkömoottoreissa vääntömomentin tuoton kannalta olennainen magneettivuo kulkee staattorin ja roottorin välillä ilmavälin kautta. Ilmaväli mallinnetaan koneensuunnittelun yhteydessä tämän vuoksi tarkasti. Elementtimenetelmällä voidaan analysoida moottoreita varsin tarkasti, mutta menetelmän käyttö vie paljon aikaa ja sovittaminen muihin laskentaympäristöihin on usein hankalaa. Tämän vuoksi voidaan käyttää riittävän tarkkuuden omaavia analyyttisiä laskentamenetelmiä, joiden sovittaminen muihin ohjelmaympäristöihin on helpompaa kuin elementtimenetelmää käytettäessä. Diplomityössä kehitetään reluktanssiverkkomalli kestomagneettien aikaansaaman ilmavälivuontiheyden mallintamiseen kestomagneettitahtikoneille, joissa on pinta-asennetut kestomagneetit. Kehitetyn reluktanssiverkkomallin toimivuutta vertaillaan muihin ilmavälivuontiheyden laskentamenetelmiin.

Sähköisen liikkeenohjauskäytön mitoitus, käyttöönoton dokumentointi ja pakkauslinjasovellukset

Frequency converters have started to gain new market areas in the field of motion control applications. The communication and control properties of frequency converters have reached the properties of traditional servo amplifiers during the past few years. In this thesis a motion control system was examined. This particular system consists of frequency converters, permanent magnet synchronous motors and linear belt drives. The properties and prerequisites for packing are discussed. A test setup was build and measurement sets were done to examine the performance of the system. Speed and accuracy measurements were done in all three dimensions. Based on the measurement results applicability of the system for packing industry was evaluated.

On the Analysis and Control of a Linear Synchronous Servomotor with a Flexible Load

Industry's growing need for higher productivity is placing new demands on mechanisms connected with electrical motors, because these can easily lead to vibration problems due to fast dynamics. Furthermore, the nonlinear effects caused by a motor frequently reduce servo stability, which diminishes the controller's ability to predict and maintain speed. Hence, the flexibility of a mechanism and its control has become an important area of research. The basic approach in control system engineering is to assume that the mechanism connected to a motor is rigid, so that vibrations in the tool mechanism, reel, gripper or any apparatus connected to the motor are not taken into account. This might reduce the ability of the machine system to carry out its assignment and shorten the lifetime of the equipment. Nonetheless, it is usually more important to know how the mechanism, or in other words the load on the motor, behaves. A nonlinear load control method for a permanent magnet linear synchronous motor is developed and implemented in the thesis. The purpose of the controller is to track a flexible load to the desired velocity reference as fast as possible and without awkward oscillations. The control method is based on an adaptive backstepping algorithm with its stability ensured by the Lyapunov stability theorem. As a reference controller for the backstepping method, a hybrid neural controller is introduced in which the linear motor itself is controlled by a conventional PI velocity controller and the vibration of the associated flexible mechanism is suppressed from an outer control loop using a compensation signal from a multilayer perceptron network. To avoid the local minimum problem entailed in neural networks, the initial weights are searched for offline by means of a differential evolution algorithm. The states of a mechanical system for controllers are estimated using the Kalman filter. The theoretical results obtained from the control design are validated with the lumped mass model for a mechanism. Generalization of the mechanism allows the methods derived here to be widely implemented in machine automation. The control algorithms are first designed in a specially introduced nonlinear simulation model and then implemented in the physical linear motor using a DSP (Digital Signal Processor) application. The measurements prove that both controllers are capable of suppressing vibration, but that the backstepping method is superior to others due to its accuracy of response and stability properties.

Eddy-current losses in rotor surface mounted permanent magnets

The aim of the work is to study the existing analytical calculation procedures found in literature to calculate the eddy-current losses in surface mounted permanent magnets within PMSM application. The most promising algorithms are implemented with MATLAB software under the dimensional data of LUT prototype machine. In addition finite elements analyze, utilized with help of Flux 2D software from Cedrat Ltd, is applied to calculate the eddy-current losses in permanent magnets. The results obtained from analytical methods are compared with numerical results.

Electrical machine in a Hybrid Electrical Vehicle

Hybrid electric vehicles (HEV) have attracted very much attention during the latest years. Increasing environmental concern and an increase in fuel prices are key factors for the growing interest towards the HEV. In a hybrid electric vehicle the power train consists of both a mechanical power system and an electric power transmission system. The major subsystems in the mechanical power system are the internal combustion engine which powers the vehicle; electric power transmission including an energy storage, power electronic inverter, hybrid control system; the electric motor drive that runs either in the generating mode or in the motoring mode to process the power flow between the energy storage and the electrical machine. This research includes two advanced electric motors for a parallel hybrid: induction machine and permanent magnets synchronous machine. In the thesis an induction motor and a permanent magnet motor are compared as propulsion motors. Electric energy storages are also studied.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.

Kestomagneettitahtikonekäyttöjen erot

Permanent magnet drives with nominal power over 10 kW were not a cost-sufficient system 25 years ago due to high material expenses. The improvements in motor drives, the rise in competition and the tightening of standards and regulations have caused that the PM-drives are more and more common in the over 10 kW nominal power range. The goal of this thesis is to research the performance in relation to nominal power of a PM-drive technique that is vastly increasing its popularity in fan related devices. The studied motor technique brushless direct current drive (BLDC) consists of a voltage source inverter, permanent motor and six-step-control. The reference drive is a brushless alternating current drive (BLAC) which consists of a VSI, PM and a hysteresis control. As a conclusion there are no major obstacles that would impede the BLDC-drive technique from expanding to larger power stages. The following factors must be taken into consideration when designing a BLDC-drive: motor’s current change rate, inverter switching frequency, motor’s nominal electric frequency, phase inductance and the current handling capability of the inverter. The fluctuating material costs create instability to the end prices of PM-motors that can in the worst case lead to diminished interest towards BLDC- and PM-drives in general.

Kestomagnetoidun roottorin mekaniikkasuunnittelu ja -analysointi

Työssä kehitettiin suurnopeuskäyttöön soveltuva kestomagnetoitu roottori olemassa olevan induktiokoneen staattorirunkoon. Kehitystyön tarkoituksena oli selvittää roottorin mekaaniset raja-arvot, kuten maksimi kehänopeus. Samalla otettiin kantaa myös tarvittaviin analysointi- ja mitoitusmenetelmiin. Maksimi kehänopeuden, laakeroinnin ja roottorin skaalattavuuden selvittäminen edellytti myös tarkkaa materiaaliselvitystä ja optimointia. Tästä syystä työn aikana tehtiin tiivistä yhteistyötä materiaalitoimittajien kanssa. Työn tuloksena syntyi uusi menetelmä toteuttaa radiaalisen magneettivuon luova kestomagneettiroottori 200 m/s kehänopeudelle. Suunniteltua roottoriratkaisua käytetään testausroottorina, jolla selvitetään valmistuksen, kokoonpanon ja sähkötehon rajoitteet käytännössä. Suunnittelutyö edellyttikin jatkuvaa iterointia sähkösuunnittelun ja roottorin osien valmistajien kanssa, jotta löydettiin paras kompromissiratkaisu roottorin prototyyppiin. Tämän seurauksena saatiin luotua varsin tarkat suunnittelu- ja analysointiraja-arvot kestomagneettiroottorin tuotteistettavia versioita varten.