Keskusteluja vuokratyöstä. Vuokratyön diskursiivinen rakentuminen Suomessa

1990-luvun alussa lainsäädäntö ja työmarkkinajärjestöt määrittelivät Suomessa, että vuokratyötä tuli käyttää vain tilapäiseen työvoimatarpeeseen, esimerkiksi sijaisuuksiin ja ruuhkahuippuihin. Joillakin aloilla vuokratyö oli työnantajien ja työntekijöiden yhteissopimuksella kielletty. Vaikka vuokratyösuhteet saivat jo 1980-luvulla niin Suomessa kuin kansainvälisestikin maineen työsuhdekeinotteluna, alkoi vuokratyön määrä Suomessa kasvaa 1990-luvun puolivälissä ja erityisesti tultaessa 2000-luvulle. Suomalaiset akateemiset tutkijat eivät ole juuri vuokratyöstä kiinnostuneet. Aiemmat, harvalukuiset tutkimukset ovat keskittyneet lähinnä työyhteisöjen ja työntekijöiden kokemuksiin sekä vuokratyön työehtoihin. Vuokratyö ymmärretäänkin edelleen lähinnä työntekijän subjektiivisena kokemuksena. Vuokratyössä on kuitenkin kysymys paitsi kokemuksista, myös yhteiskunnallisesta valtakamppailusta, jossa diskursiivisin keinoin pyritään vaikuttamaan ilmiöön nimeltä vuokratyö, laajemmin ilmiöön nimeltä työmarkkinat, sekä toisaalta kansalaisten käsityksiin työelämän ”normaalista”. Käsillä oleva tutkimus laajentaa ymmärrystä vuokratyöstä tarkastelemalla ilmiötä lainsäädännön, uutisoinnin ja markkinoinnin rakentamien julkisten käsitysten ja merkityksenantojen kautta. Teoreettisena viitekehyksenä käytän hallinnan ja työprosessin säätelyn teoriaperinteitä. Se, miten työmarkkinoiden muutosta ja uusia työsuhdemuotoja politiikassa, mediassa, lainsäädännössä, tai työpaikan kahvipöytäkeskusteluissa perustellaan ja tehdään ymmärrettäväksi, on samalla työelämään kiinnitettävien arvojen, merkitysten ja toimijuuksien luomista, rajaamista ja kuvailua. Työelämäpuheessa ei siis ole kyse vain talouden lainalaisuuksista, kansantalouden toimivuudesta, tai yritysten kilpailukyvystä, vaan myös ja erityisesti niiden toimijoiden luomisesta, määrittelemisestä ja legitimoimisesta, jotka työelämän kentällä saavat toimia ja tulevat palkituiksi. Säätelyn ja hallinnan näkökulmasta on relevanttia tarkastella millaisilla käsitteillä ja merkityksillä vuokratyötä ilmiönä rakennetaan . Tutkimuskysymyksinä esitän: 1) Miten ja millä perusteilla vuokratyöstä rakennettiin Suomessa legitiimi tapa työllistää ja työllistyä? 2) Millaisia työntekijäideaaleja vuokratyöhön liittyvissä keskusteluissa rakennetaan? Tutkimusaineistona tarkastelen lainsäädäntöön liittyviä dokumentteja, Helsingin Sanomien uutisointia, vuokratyöyritysten markkinointimateriaaleja, sekä vuokratyöyritysten edustajien haastatteluita. Analyysimenetelmänä käytän kriittistä diskurssianalyysia. Tämä menetelmä mahdollistaa puheen ja dokumenttien tarkastelun sosiaalisena toimintana, jolla eri toimijat pyrkivät osallistumaan yhteiskunnassa hyväksyttyjen ja tunnustettujen käsitysten ja toimintavaihtoehtojen rakentamis-, tulkinta- ja määrittelyprosesseihin. Tutkimukseni päätuloksena esitän, että vuokratyöstä muodostui legitiimi tapa työllistää Suomessa 1990-luvulla, koska vuokratyö käsitteellistettiin sekä lainsäädännön että median diskursseissa ennen kaikkea ratkaisuksi työttömyyteen. Toisaalta vuokratyö käsitteellistettiin vain marginaalisten työntekijäryhmien (naiset ja opiskelijat) rooliksi, jolloin se ei liittynyt miesvaltaisten työpaikkojen arkeen. Ratkaisuna työttömyyteen vuokratyö myös samalla luonnollistettiin osaksi yleisempää työmarkkinakehitystä, jolle ”kukaan ei voi mitään”. 2000-luvulla vuokratyö jatkoi voittokulkuaan ja rakentui pysyväksi ilmiöksi, koska työlainsäädännön uudistus institutionalisoi vuokratyön työehtosopimusmenettelyyn, jolloin sen ”salonkikelpoisuus” ja normaalius vahvistettiin. Vaikka työehtosopimusasia oli ratkaisuna merkittävä, nousi vuokratyön osalta itse työehtosopimus tärkeämmäksi kuin sen sisältö. Työehtosopimuksilla ei kuitenkaan pystytty vaikuttamaan esimerkiksi vuokratyöntekijän olemattomaan työsuhdeturvaan. Lisäksi työnantajapuhe käsitteellistää vuokratyön 2000-luvulla ennen kaikkea työmarkkinavaihtoehdoksi, vapautta ja monipuolisia työkokemuksia tarjoavaksi työmarkkinoiden katalysaattoriksi. Vuokratyö on tässä merkitysavaruudessa työntekijöille ”vain” yksi tapa työllistyä ja löytää oma tiensä työmarkkinoille, ei suinkaan työnantajien sanelema pakko. Työntekijöihin kohdistuva hallintapuhe niin mediassa kuin työnantajien haastatteluissakin pyrkii puolestaan rakentamaan ideaalityöntekijäkuvaksi yrittäjämäisen oman elämänsä toimitusjohtajan. Työnantajien diskursseissa kaikuvatkin työntekijään kohdistuva vaatimus itse itsensä ohjaamisesta sekä työntekijäidentiteetin muotoilemisesta joustavuutta, sopeutuvuutta, vaihtelua ja jatkuvaa muutosta vähintäänkin sietäväksi, mutta mieluiten näitä ominaisuuksia jopa aktiivisesti hakevaksi ja arvostavaksi. Työmarkkinoiden toimijana on nimenomaisesti yksilö, jonka mahdollisuudet menestyä ovat vain ja ainoastaan hänen omissa käsissään. Työntekijän roolin korostaminen aktiivisena toimijana ja vuokratyöstä ”oikeita”, norminmukaisia sisältöjä löytävänä pärjääjänä on diskursiivisesti hallittua yritystä ohjata työntekijöitä näkemään sekä itsensä tietynlaisina toimijoina että työmarkkinat tietyllä tavalla toimivina. Vuokratyössä ei ole kyse vain työntekijöiden yksilöllisistä tai yksittäisistä kokemuksista. Vuokratyö on yhteiskunnallisen merkityskamppailun tulos, jossa käyttövoimana ovat toimineet hallinnalliset ja säätelyyn pyrkivät käsitteellistykset työllisyydestä, yksilön valinnasta ja koko yhteiskunnan edusta. Hallinnan ja säätelyn näkökulmasta katsottuna vuokratyö on myös merkinnyt säätelyn liukumista tasa-arvoa, yhdenmukaista kohtelua ja työntekijän suojelua korostavasta viranomaisten ja poliittisten toimijoiden suorittamasta työmarkkinoiden kollektiivisesta säätelystä työnantajien ylläpitämään työntekijän persoonan ja käyttäytymisen hegemoniseen, yksilölliseen säätelyyn.

Jatkuvan äänitehojakautuman algoritmi pitkien käytävien äänikenttien mallintamiseen

JÄKÄLA-algoritmi (Jatkuvan Äänitehojakautuman algoritmi Käytävien Äänikenttien LAskentaan) ja sen NUMO- ja APPRO-laskentayhtälöt perustuvat käytävällä olevan todellisen äänilähteen kuvalähteiden symmetriaan. NUMO on algoritmin numeerisen ratkaisun ja APPRO likiarvoratkaisun laskentayhtälö. Algoritmia johdettaessa oletettiin, että absorptiomateriaali oli jakautunut tasaisesti käytävän ääntä heijastaville pinnoille. Suorakaiteen muotoisen käytävän kuvalähdetason muunto jatkuvaksi äänitehojakautumaksi sisältää kolme muokkausvaihetta. Aluksi suorakaiteen kuvalähdetaso muunnetaan neliön muotoiseksi. Seuraavaksi neliön muotoisen kuvalähdetason samanarvoiset kuvalähteet siirretään koordinaattiakselille diskreetiksi kuvalähdejonoksi. Lopuksi kuvalähdejono muunnetaan jatkuvaksi äänitehojakautumaksi, jolloin käytävän vastaanottopisteen äänenpainetaso voidaan laskea integroimalla jatkuvan äänitehojakautuman yli. JÄKÄLA-algoritmin validiteetin toteamiseksi käytettiin testattua kaupallista AKURI-ohjelmaa. AKURI-ohjelma antoi myös hyvän käsityksen siitä, miten NUMO- ja APPRO-yhtälöillä lasketut arvot mahdollisesti eroavat todellisilla käytävillä mitatuista arvoista. JÄKÄLA-algoritmin NUMO- ja APPRO-yhtälöitä testattiin myös vertaamalla niiden antamia tuloksia kolmen erityyppisen käytävän äänenpainetasomittauksiin. Tässä tutkimuksessa on osoitettu, että akustisen kuvateorian pohjalta on mahdollista johtaa laskenta-algoritmi, jota voidaan soveltaa pitkien käytävien äänikenttien pika-arvioinnissa paikan päällä. Sekä teoreettinen laskenta että käytännön äänenpainetasomittaukset todellisilla käytävillä osoittivat, että JÄKÄLA-algoritmin yhtälöiden ennustustarkkuus oli erinomainen ideaalikäytävillä ja hyvä niillä todellisilla käytävillä, joilla ei ollut ääntä heijastavia rakenteita. NUMO- ja APPRO-yhtälöt näyttäisivät toimivan hyvin käytävillä, joiden poikkileikkaus oli lähes neliön muotoinen ja joissa pintojen suurin absorptiokerroin oli korkeintaan kymmenen kertaa pienintä absorptiokerrointa suurempi. NUMO- ja APPRO-yhtälöiden suurin puute on, etteivät ne ota huomioon pintojen erilaisia absorptiokertoimia eivätkä esineistä heijastuvia ääniä. NUMO- ja APPRO- laskentayhtälöt poikkesivat mitatuista arvoista eniten käytävillä, joilla kahden vastakkaisen pinnan absorptiokerroin oli hyvin suuri ja toisen pintaparin hyvin pieni, ja käytävillä, joissa oli massiivisia, ääntä heijastavia pilareita ja palkkeja. JÄKÄLA-algoritmin NUMO- ja APPRO-yhtälöt antoivat tutkituilla käytävillä kuitenkin selvästi tarkempia arvoja kuin Kuttruffin likiarvoyhtälö ja tilastollisen huoneakustiikan perusyhtälö. JÄKÄLA-algoritmin laskentatarkkuutta on testattu vain neljällä todellisella käytävällä. Algoritmin kehittämiseksi tulisi jatkossa käytävän vastakkaisia pintoja ja niiden absorptiokertoimia käsitellä laskennassa pareittain. Algoritmin validiteetin varmistamiseksi on mittauksia tehtävä lisää käytävillä, joiden absorptiomateriaalien jakautumat poikkeavat toisistaan.

Vauhtikausi. Autoilun sukupuoli 1920-luvun Suomessa

The Age of Speed:Automobility’s Gender in the 1920s Finland The aim of this study is to analyze the connections between automobility and gender in Finland in the 1920s. In this study it is argued that the 1920s was the significant era in the Finnish history of automobility when many of the long-lasting gendered notions and cultural understandings were constructed. This study combines cultural history of technology with gender analysis. As the previous research on gender and technology has recognized, technology is a significant site of gender negotiations. Both from the cultural historical perspective and a gender perspective it is important to understand both technology and gender as cultural constructions. They were linked together and constructed each other. In other words: technology shapes gender and gender shapes technology. Historians of technology like Nina Lerman, Ruth Oldenziel and Arwen Mohun have argued that both gender and technology are about power: social, cultural, economic and political. In this study automobility means technology that can be analyzed in layers of identity, structures, institutions and representations. The source material consists of various types of historical sources, magazines and journals, advertisements, archival material together with films and literature. In the previous studies of the history of automobility gender has often been neglected. The term “gender” has also quite often been misunderstood. Some studies in the field have only focused on the early female drivers. However, far too little attention has been paid to the question, why automobility was considered as masculine sphere only. This study aims to give new insights to the previous interpretations of the history of automobility. As in various other countries also in Finland, the decade of the 1920s is characterized as a period of “modern times.” It was also the era of the automobiles. Although the number of cars in Finland was still low compared to the other European countries and the USA, in press, films and literature, images of automobiles and new women – and men – on the wheel became as an emblem of a new era. The thesis consists of three main chapters. The first main chapter focuses on the conflicts between drivers and non-drivers. The study shows how in the debate of the automobility “a driver” was constantly referred as a man and “a pedestrian” accordingly a woman, even though in the reality there were as much men and women walking on the streets and the roads. Thus, the public debate constructed and reconstructed the gendered traffic system where men were playing the key role. The second main chapter of the study analyses the automobile clubs and the cultural representations. The chapter answers the question how the concept of a driver was gendered. The Automobile clubs and the organizations of professional drivers were in a significant role in developing the early history of traffic in Finland. The Finnish Automobile Club (Suomen Automobiili Klubi, founded in 1919) was the oldest and the most powerful of all automobile organizations. The Finnish Automobile Club accepted women as members from the very beginning. The membership was strictly limited to the upper class and the very first female members were wives and daughters of the male members. However, Doctor of medicine and surgery 316 Karolina Eskelin (1867-1936) the founding member of the Club was an exception to that convention. The male members of the Finnish Automobile Club attended official international meetings and consulted Finnish authorities in traffic and road questions, whereas, female members joined car trips, picnics and social gatherings arranged by the club. Few young female members of the club drove in races and gross-country-tours. The cultural representations of drivers in the Finnish media in the 1920s both deconstructed and reconstructed the concept of gender. In Finnish press in general, motoring was seen as male dominated area. Men were represented as the experts of the automobility. The drivers’ uniforms and the automobile clubs underlined professionalism and expertise which, thus, got masculine meaning. Women were beautiful accessories in the car ads, but they were also becoming a new consumer group in the market. The representations of the female and the male drivers influenced and shaped actively the understandings of femininity and masculinity. In the third main chapter the analysis focuses on the automobile as an artifact.The automobile was considered as an artifact that primarily belonged to the masculine domain. However, the representations of the automobiles were ambivalent. The automobile was both masculine and feminine depending on the context. The representations of the automobile were also used to construct the discourse of heteronormativity.

Integration of Torrefaction with Steam Power Plant

Torrefaction is one of the pretreatment technologies to enhance the fuel characteristics of biomass. The efficient and continuous operation of a torrefaction reactor, in the commercial scale, demands a secure biomass supply, in addition to adequate source of heat. Biorefinery plants or biomass-fuelled steam power plants have the potential to integrate with the torrefaction reactor to exchange heat and mass, using available infrastructure and energy sources. The technical feasibility of this integration is examined in this study. A new model for the torrefaction process is introduced and verified by the available experimental data. The torrefaction model is then integrated in different steam power plants to simulate possible mass and energy exchange between the reactor and the plants. The performance of the integrated plant is investigated for different configurations and the results are compared.

Mitigation possibilities to Greenhouse gas emissions from power production in India

Global warming is assertively the greatest environmental challenge for humans of 21st century. It is primarily caused by the anthropogenic greenhouse gas (GHG) that trap heat in the atmosphere. Because of which, the GHG emission mitigation, globally, is a critical issue in the political agenda of all high-profile nations. India, like other developing countries, is facing this threat of climate change while dealing with the challenge of sustaining its rapid economic growth. India’s economy is closely connected to its natural resource base and climate sensitive sectors like water, agriculture and forestry. Due to Climate change the quality and distribution of India’s natural resources may transform and lead to adverse effects on livelihood of its people. Therefore, India is expected to face a major threat due to the projected climate change. This study proposes possible solutions for GHG emission mitigation that are specific to the power sector of India. The methods discussed here will take Indian power sector from present coal dominant ideology to a system, centered with renewable energy sources. The study further proposes a future scenario for 2050, based on the present Indian government policies and global energy technologies advancements.

Modelling of ultrasound assisted mixing in Newtonian and non-Newtonian liquids

The purpose of this work is to obtain a better understanding of behaviour of possible ultrasound appliance on fluid media mixing. The research is done in the regard to Newtonian and non-Newtonian fluids. The process of ultrasound appliance on liquids is modelled in COMSOL Multiphysics software. The influence of ultrasound using is introduced as waveform equation. Turbulence modelling is fulfilled by the k-ε model in Newtonian fluid. The modeling of ultrasound assisted mixing in non-Newtonian fluids is based on the power law. To verify modelling results two practical methods are used: Particle Image Velocimetry and measurements of mixing time. Particle Image Velocimetry allows capturing of velocity flow field continuously and presents detailed depiction of liquid dynamics. The second way of verification is the comparison of mixing time of homogeneity. Experimentally achievement of mixing time is done by conductivity measurements. In modelling part mixing time is achieved by special module of COMSOL Multiphysics – the transport of diluted species. Both practical and modelling parts show similar radial mechanism of fluid flow under ultrasound appliance – from the horn tip fluid moves to the bottom and along the walls goes back. Velocity profiles are similar in modelling and experimental part in the case of Newtonian fluid. In the case of non-Newtonian fluid velocity profiles do not agree. The development track of ultrasound-assisted mixing modelling is presented in the thesis.

Potential and Challenges of Analog Reconfigurable Computation in Modern and Future CMOS

In this work, the feasibility of the floating-gate technology in analog computing platforms in a scaled down general-purpose CMOS technology is considered. When the technology is scaled down the performance of analog circuits tends to get worse because the process parameters are optimized for digital transistors and the scaling involves the reduction of supply voltages. Generally, the challenge in analog circuit design is that all salient design metrics such as power, area, bandwidth and accuracy are interrelated. Furthermore, poor flexibility, i.e. lack of reconfigurability, the reuse of IP etc., can be considered the most severe weakness of analog hardware. On this account, digital calibration schemes are often required for improved performance or yield enhancement, whereas high flexibility/reconfigurability can not be easily achieved. Here, it is discussed whether it is possible to work around these obstacles by using floating-gate transistors (FGTs), and analyze problems associated with the practical implementation. FGT technology is attractive because it is electrically programmable and also features a charge-based built-in non-volatile memory. Apart from being ideal for canceling the circuit non-idealities due to process variations, the FGTs can also be used as computational or adaptive elements in analog circuits. The nominal gate oxide thickness in the deep sub-micron (DSM) processes is too thin to support robust charge retention and consequently the FGT becomes leaky. In principle, non-leaky FGTs can be implemented in a scaled down process without any special masks by using “double”-oxide transistors intended for providing devices that operate with higher supply voltages than general purpose devices. However, in practice the technology scaling poses several challenges which are addressed in this thesis. To provide a sufficiently wide-ranging survey, six prototype chips with varying complexity were implemented in four different DSM process nodes and investigated from this perspective. The focus is on non-leaky FGTs, but the presented autozeroing floating-gate amplifier (AFGA) demonstrates that leaky FGTs may also find a use. The simplest test structures contain only a few transistors, whereas the most complex experimental chip is an implementation of a spiking neural network (SNN) which comprises thousands of active and passive devices. More precisely, it is a fully connected (256 FGT synapses) two-layer spiking neural network (SNN), where the adaptive properties of FGT are taken advantage of. A compact realization of Spike Timing Dependent Plasticity (STDP) within the SNN is one of the key contributions of this thesis. Finally, the considerations in this thesis extend beyond CMOS to emerging nanodevices. To this end, one promising emerging nanoscale circuit element - memristor - is reviewed and its applicability for analog processing is considered. Furthermore, it is discussed how the FGT technology can be used to prototype computation paradigms compatible with these emerging two-terminal nanoscale devices in a mature and widely available CMOS technology.

Working fluid selection and design of small-scale waste heat recovery systems based on organic Rankine cycles

Demand for the use of energy systems, entailing high efficiency as well as availability to harness renewable energy sources, is a key issue in order to tackling the threat of global warming and saving natural resources. Organic Rankine cycle (ORC) technology has been identified as one of the most promising technologies in recovering low-grade heat sources and in harnessing renewable energy sources that cannot be efficiently utilized by means of more conventional power systems. The ORC is based on the working principle of Rankine process, but an organic working fluid is adopted in the cycle instead of steam. This thesis presents numerical and experimental results of the study on the design of small-scale ORCs. Two main applications were selected for the thesis: waste heat re- covery from small-scale diesel engines concentrating on the utilization of the exhaust gas heat and waste heat recovery in large industrial-scale engine power plants considering the utilization of both the high and low temperature heat sources. The main objective of this work was to identify suitable working fluid candidates and to study the process and turbine design methods that can be applied when power plants based on the use of non-conventional working fluids are considered. The computational work included the use of thermodynamic analysis methods and turbine design methods that were based on the use of highly accurate fluid properties. In addition, the design and loss mechanisms in supersonic ORC turbines were studied by means of computational fluid dynamics. The results indicated that the design of ORC is highly influenced by the selection of the working fluid and cycle operational conditions. The results for the turbine designs in- dicated that the working fluid selection should not be based only on the thermodynamic analysis, but requires also considerations on the turbine design. The turbines tend to be fast rotating, entailing small blade heights at the turbine rotor inlet and highly supersonic flow in the turbine flow passages, especially when power systems with low power outputs are designed. The results indicated that the ORC is a potential solution in utilizing waste heat streams both at high and low temperatures and both in micro and larger scale appli- cations.

Numerical simulation of two-chamber plasma sources using finite element method

Numerical simulation of plasma sources is very important. Such models allows to vary different plasma parameters with high degree of accuracy. Moreover, they allow to conduct measurements not disturbing system balance.Recently, the scientific and practical interest increased in so-called two-chamber plasma sources. In one of them (small or discharge chamber) an external power source is embedded. In that chamber plasma forms. In another (large or diffusion chamber) plasma exists due to the transport of particles and energy through the boundary between chambers.In this particular work two-chamber plasma sources with argon and oxygen as active mediums were onstructed. This models give interesting results in electric field profiles and, as a consequence, in density profiles of charged particles.

Promoting Growth in the Use of Bioenergy in Europe by Converting Existing Coal-Fired Power Plants to Biomass

Repowering existing power plants by replacing coal with biomass might offer an interesting option to ease the transition from fossil fuels to renewable energy sources and promote a fur-ther expansion of bioenergy in Europe, on account of the potential to decrease greenhouse gas emissions, as well as other pollutants (SOx, NOx, etcetera). In addition, a great part of the appeal of repowering projects comes from the opportunity to reuse the vast existing invest-ment and infrastructure associated with coal-based power generation. Even so, only a limited number of experiences with repowering are found. Therefore, efforts are required to produce technical and scientific evidence to determine whether said technology might be considered feasible for its adoption within European conditions. A detailed evaluation of the technical and economic aspects of this technology constitutes a powerful tool for decision makers to define the energy future for Europe. To better illustrate this concept, a case study is analyzed. A Slovakian pulverized coal plant was used as the basis for determining the effects on perfor-mance, operation, maintenance and cost when fuel is shifted to biomass. It was found that biomass fuel properties play a crucial role in plant repowering. Furthermore, results demon-strate that this technology offers renewable energy with low pollutant emissions at the cost of reduced capacity, relatively high levelized cost of electricity and sometimes, a maintenance-intensive operation. Lastly, regardless of the fact that existing equipment can be reutilized for the most part, extensive additions/modifications may be required to ensure a safe operation and an acceptable performance.

Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Reducing auxiliary power of a fluid bed boiler island

The aim of this thesis is to find and analyze different methods which reduce fluid bed boilers’ auxiliary power consumption. The objective is to examine the effects and feasibility of these methods. The literature part explains how fluid bed boilers work and what are the main sources of auxiliary power consumption. Designs and operation of these equipment are presented. The literature part also discusses the basics of auxiliary power consumption reduction and introduces four low pressure drop constructions. The experimental part inspects six different methods. Effects of these methods on the auxiliary power consumption are calculated and their impacts on the operation of the boiler are modeled. Calculations show that reasonable changes can reduce fluid bed boiler’s auxiliary power consumption by 2,1-10,2 %. Biggest reductions come from lower air coefficients, smaller bed a-level pressures and lower primary/secondary air –ratios. Models showed no problems with the smaller bed a-level pressures. With the lower air coefficients and smaller primary/secondary air –ratios the models showed a significant increase in the carbon monoxide levels.

Between Dugin’s Eurasianism and Mahan’s Sea Power Concept: Russia’s Geopolitical Discourse within Foucault’s ‘Discursive Tree’ before and After the Incorporation of the Crimea

The fall of 2013 could be characterized as a crossroad in the geopolitics of Eastern Europe, namely Ukraine. Two rivalry geopolitical projects have been developing throughout the post-Cold War years, and it seems that they reached a collision point in Ukraine; a country whose authorities have been for long switching sides between the European Union and the Russian Federation in their foreign policy commitments. The refusal/postponing to sign the Association Agreement with Brussels, an expected event by a large category of the Ukrainian society, by Yanukovich’s government led to the outset of the latter; and brought a pro-Western, anti-Russian government in Kyiv. It seems that Ukraine, after those events, has embarked definitively on the path of integration into the West (European Union and possibly NATO). The Russian Federation, who has been throughout Putin’s years engaged into the re-integration of post-Soviet space, reacted to these developments in an assertive manner by violating borders, agreements and the territorial integrity of Ukraine. Thus, the incorporation of the Crimea into the Russian Federation is the first in its kind in the post-Soviet space, despite the existence of various other conflicts that broke out in the region after the Soviet Union broke up. I will investigate in this thesis the nature of what will be labelled, in this work, the Crimean issue. I argue that the incorporation of the Crimean peninsula into the Russian Federation marks a new era in Russian geopolitical thinking that shapes, to a far extent, Russian foreign policy. Discourse analysis will be the methodological basis for this study, with a special focus on Michel Foucault’s Archaeology of Knowledge. The innovation that this research brings is the fact that it discusses Russian geopolitical discourse within the scope of Foucault’s ‘discursive tree’, with a reference to the Crimean issue. A wide range of primary sources will be consulted in this study such as presidential addresses to the Federal Assembly (2000-2014), Foreign Policy Concepts of the Russian Federation (2000, 2008), Russian maritime doctrines, as wells as Dugin’s Osnovy Geopolitiki (Foundations of Geopolitics), Mahan’s (The Influence of Sea Power Upon History, 1660–1783) and other Eurasianism related literature.

POLITICAL RISK IN FOREIGN DIRECT INVESTMENT IN THE RUSSIAN ELECTRIC POWER SECTOR

Russia approved ambitious reform plan for the electricity sector in 2001 including privatisation of the country’s huge thermal generation assets. So far the sector had suffered from power shortages, aging infrastructure, substantial electricity losses, and weak productivity and profitability numbers. There was obvious need for foreign investments and technologies. The reform was rather successful; the generation assets were privatised in auctions in 2007-2008 and three European energy companies, E.On, Enel and Fortum, invested in and obtained together over 10% of the Russian production assets. The novelty of these foreign investments serves unique object for the study. The political risk is involved in the FDI due to the industry’s social and economic importance. The research’s objective was to identify and analyse the political risk that foreign investors face in the Russian electricity sector. The research had qualitative study method and the empirical data was collected by interviewing. The research’s theoretical framework was based on the existing political risk theories and it focused to understand the Russian government in relation to the country’s stability and define both macro-level and micro-level sources of political risk for the foreign direct investments in the sector. The research concludes that the centralised and obscure political decision-making, economic constriction, high level of governmental control in economy and corruption form the country’s internal macro-level risk sources for the foreign investors in the sector. Additionally the retribution due to the companies’ home country actions, possible violent confrontations at the Russian borders and the currency instability are externally originated risk sources. In the electricity industry there is risk of tightened governmental control and increased regulation and taxation. Similarly the company-level risk sources link to the unreformed heating sector, bargaining with the authorities, diplomatic stress between host and home countries and to companies and government’s divergent perspective for the profit-making. The research stresses the foreign companies’ ability to cope with the characteristics of Russian political environment. In addition to frequent political and market risk assessment, the companies need to focus on currency protection against rouble’s rate fluctuation and actively build good company-citizenship in the country. Good relationship is needed with the Russian political authorities. The political risk identification and the research’s conclusive framework also enable political risk study assessments for other industries in Russia

Screening of power to gas projects

The purpose of this thesis was the screening of power to gas projects worldwide and reviewing the technologies used and applications for the end products. This study focuses solely on technical solutions and feasibility, economical profitability is excluded. With power grids having larger penetrations of intermittent sources such as solar and wind power, the demand and production cannot be balanced in conventional methods. Technologies for storing electric power in times of surplus production are needed, and the concept called power to gas is a solution for this problem. A total of 57 projects mostly located in Europe were reviewed by going through publications, presentations and project web pages. Hydrogen is the more popular end product over methane. Power to gas is a viable concept when power production from intermittent sources needs to be smoothed and time shifted, when carbon free fuels are produced for vehicles and when chemical industry needs carbon neutral raw materials.