Influence of surface functionalization on the behavior of silica nanoparticles in biological systems

Personalized nanomedicine has been shown to provide advantages over traditional clinical imaging, diagnosis, and conventional medical treatment. Using nanoparticles can enhance and clarify the clinical targeting and imaging, and lead them exactly to the place in the body that is the goal of treatment. At the same time, one can reduce the side effects that usually occur in the parts of the body that are not targets for treatment. Nanoparticles are of a size that can penetrate into cells. Their surface functionalization offers a way to increase their sensitivity when detecting target molecules. In addition, it increases the potential for flexibility in particle design, their therapeutic function, and variation possibilities in diagnostics. Mesoporous nanoparticles of amorphous silica have attractive physical and chemical characteristics such as particle morphology, controllable pore size, and high surface area and pore volume. Additionally, the surface functionalization of silica nanoparticles is relatively straightforward, which enables optimization of the interaction between the particles and the biological system. The main goal of this study was to prepare traceable and targetable silica nanoparticles for medical applications with a special focus on particle dispersion stability, biocompatibility, and targeting capabilities. Nanoparticle properties are highly particle-size dependent and a good dispersion stability is a prerequisite for active therapeutic and diagnostic agents. In the study it was shown that traceable streptavidin-conjugated silica nanoparticles which exhibit a good dispersibility could be obtained by the suitable choice of a proper surface functionalization route. Theranostic nanoparticles should exhibit sufficient hydrolytic stability to effectively carry the medicine to the target cells after which they should disintegrate and dissolve. Furthermore, the surface groups should stay at the particle surface until the particle has been internalized by the cell in order to optimize cell specificity. Model particles with fluorescently-labeled regions were tested in vitro using light microscopy and image processing technology, which allowed a detailed study of the disintegration and dissolution process. The study showed that nanoparticles degrade more slowly outside, as compared to inside the cell. The main advantage of theranostic agents is their successful targeting in vitro and in vivo. Non-porous nanoparticles using monoclonal antibodies as guiding ligands were tested in vitro in order to follow their targeting ability and internalization. In addition to the targeting that was found successful, a specific internalization route for the particles could be detected. In the last part of the study, the objective was to clarify the feasibility of traceable mesoporous silica nanoparticles, loaded with a hydrophobic cancer drug, being applied for targeted drug delivery in vitro and in vivo. Particles were provided with a small molecular targeting ligand. In the study a significantly higher therapeutic effect could be achieved with nanoparticles compared to free drug. The nanoparticles were biocompatible and stayed in the tumor for a longer time than a free medicine did, before being eliminated by renal excretion. Overall, the results showed that mesoporous silica nanoparticles are biocompatible, biodegradable drug carriers and that cell specificity can be achieved both in vitro and in vivo.

Understanding Online Game Players' Post-adoption Behavior: an Investigation of Social Network Games in China

Retaining players and re-attracting switching players has long been a central topic for SNG providers with regard to the post-adoption stage of playing an online game. However, there has not been much research which has explored players’ post-adoption behavior by incorporating the continuance intention and the switching intention. In addition, traditional IS continuance theories were mainly developed to investigate users’ continued use of utilitarian IS, and thus they may fall short when trying to explain the continued use of hedonic IS. Furthermore, compared to the richer literature on IS continuance, far too little attention has been paid to IS switching, leading to a dearth of knowledge on the subject, despite the increased incidence of the switching phenomenon in the IS field. By addressing the limitations of prior literature, this study seeks to examine the determinants of SNG players’ two different post-adoption behaviors, including the continuance intention and the switching intention. This study takes a positivist approach and uses survey research method to test five proposed research models based on Unified Theory of Acceptance and Use of Technology 2; Use and Gratification Theory; Push-Pull-Mooring model; Cognitive Dissonance Theory; and a self-developed model respectively with empirical data collected from the SNG players of one of the biggest SNG providers in China. A total of 3919 valid responses and 541 valid responses were used to examine the continuance intention and the switching intention, respectively. SEM is utilized as the data analysis method. The proposed research models are supported by the empirical data. The continuance intention is determined by enjoyment, fantasy, escapism, social interaction, social presence, social influence, achievement and habit. The switching intention is determined by enjoyment, satisfaction, subjective norms, descriptive norms, alternative attractiveness, the need for variety, change experience, and adaptation cost. This study contributes to IS theories in three important ways. Firstly, it shows IS switching should be included in IS post-adoption research together with IS continuance. Secondly, a modern IS is usually multi-functional and SNG players have multiple reasons for using a SNG, thus a player’s beliefs about the hedonic, social and utilitarian perceptions of their continued use of the SNG exert significant effects on the continuance intention. Thirdly, the determinants of the switch ing intention mainly exert push, pull, and mooring effects. Players’ beliefs about their current SNG and the available alternatives, as well as their individual characteristics are all significant determinants of the switching intention. SNG players combine these effects in order to formulate the switching intention. Finally, this study presents limitations and suggestions for future research.

Guilt, shame, emotion regulation, and social cognition: Understanding their associations with preadolescents' social behavior

In this thesis, two negatively valenced emotions are approached as reflecting children’s self-consciousness, namely guilt and shame. Despite the notable role of emotions in the psychological research, empirical research findings on the links between guilt, shame, and children’s social behavior – and particularly aggression – have been modest, inconsistent, and sometimes contradictory. This thesis contains four studies on the associations of guilt, shame, emotion regulation, and social cognitions with children’s social behavior. The longitudinal material of the thesis was collected as a survey among a relatively large amount of Finnish preadolescents. In Study I, the distinctiveness of guilt and shame in children’s social behavior were investigated. The more specific links of emotions and aggressive behavior were explored in Study II, in which emotion regulation and negative emotionality were treated as the moderators between guilt, shame, and children’s aggressive behavior. The role of emotion management was further evaluated in Study III, in which effortful control and anger were treated as the moderators between domain-specific aggressive cognitions and children’s aggressive behavior. In the light of the results from the Studies II and III, it seems that for children with poor emotion management the effects of emotions and social cognitions on aggressive behavior are straight-forward, whereas effective emotion management allows for reframing the situation. Finally, in Study IV, context effects on children’s anticipated emotions were evaluated, such that children were presented a series of hypothetical vignettes, in which the child was acting as the aggressor. Furthermore, the identity of the witnesses and victim’s reactions were systematically manipulated. Children anticipated the most shame in situations, in which all of the class was witnessing the aggressive act, whereas both guilt and shame were anticipated the most in the situations, in which the victim was reacting with sadness. Girls and low-aggressive children were more sensitive to contextual cues than boys and high-aggressive children. Overall, the results of this thesis suggest that the influences of guilt, shame, and social cognition on preadolescents’ aggressive behavior depend significantly on the nature of individual emotion regulation, as well as situational contexts. Both theoretical and practical implications of this study highlight a need to acknowledge effective emotion management as enabling the justification of one’s own immoral behavior.

Studies on membrane properties of cholesterol and 3-beta modified sterol analogs

Cholesterol (Chol) is an important lipid in cellular membranes functioning both as a membrane fluidity regulator, permeability regulator and co-factor for some membrane proteins, e.g. G-protein coupled receptors. It also participates in the formation of signaling platforms and gives the membrane more mechanical strenght to prevent osmotic lysis of the cell. The sterol structure is very conserved and already minor structural modifications can completely abolish its membrane functions. The right interaction with adjacent lipids and the preference of certain lipid structures over others are also key factors in determining the membrane properties of cholesterol. Because of the many important properties of cholesterol it is of value to understand the forces and structural properties that govern the membrane behavior of this sterol. In this thesis we have used established fluorescence spectroscopy methods to study the membrane behavior of both cholesterol and some of its 3β-modified analogs. Using several fluorescent probes we have established how the acyl chain order of the two main lipid species, sphingomyelin (SM) and phosphatidylcholine (PC) affect sterol partitioning as well as characterized the membrane properties of 3β-aminocholesterol and cholesteryl phosphocholine. We concluded that cholesterol prefers SM over PC at equal acyl chain order, indicating that other structural properties besides the acyl chain order are important for sphingomyelin-sterol interactions. A positive charge at the 3β position only caused minor changes in the sterol membrane behavior compared to cholesterol. A large phosphocholine head group caused a disruption in membrane packing together with other membrane lipids with large head groups, but was also able to form stable fluid bilayers together with ceramide and cholesterol. The Ability of the large head group sterol to form bilayers together with ceramide was further explored in the last paper where cholesteryl phosphocholine/ceramide (Chol-PC/Cer) complexes were successfully used to transfer ceramide into cultured cells.

Behavior of black liquor nitrogen in combustion : formation of cyanate

The Kraft pulping process is the dominant chemical pulping process in the world. Roughly 195 million metric tons of black liquor are produced annually as a by-product from the Kraft pulping process. Black liquor consists of spent cooking chemicals and dissolved organics from the wood and can contain up to 0.15 wt% nitrogen on dry solids basis. The cooking chemicals from black liquor are recovered in a chemical recovery cycle. Water is evaporated in the first stage of the chemical recovery cycle, so the black liquor has a dry solids content of 65-85% prior to combustion. During combustion of black liquor, a portion of the black liquor nitrogen is volatilized, finally forming N2 or NO. The rest of the nitrogen remains in the char as char nitrogen. During char conversion, fixed carbon is burned off leaving the pulping chemicals as smelt, and the char nitrogen forms mostly smelt nitrogen (cyanate, OCN-). Smelt exits the recovery boiler and is dissolved in water. The cyanate from smelt decomposes in the presence of water, forming NH3, which causes nitrogen emissions from the rest of the chemical recovery cycle. This thesis had two focuses: firstly, to determine how the nitrogen chemistry in the recovery boiler is affected by modification of black liquor; and secondly, to find out what causes cyanate formation during thermal conversion, and which parameters affect cyanate formation and decomposition during thermal conversion of black liquor. The fate of added biosludge nitrogen in chemical recovery was determined in Paper I. The added biosludge increased the nitrogen content of black liquor. At the pulp mill, the added biosludge did not increase the NO formation in the recovery boiler, but instead increased the amount of cyanate in green liquor. The increased cyanate caused more NH3 formation, which increased the NCG boiler’s NO emissions. Laboratory-scale experiments showed an increase in both NO and cyanate formation after biosludge addition. Black liquor can be modified, for example by addition of a solid biomass to increase the energy density of black liquor, or by separation of lignin from black liquor by precipitation. The precipitated lignin can be utilized in the production of green chemicals or as a fuel. In Papers II and III, laboratory-scale experiments were conducted to determine the impact of black liquor modification on NO and cyanate formation. Removal of lignin from black liquor reduced the nitrogen content of the black liquor. In most cases NO and cyanate formation decreased with increasing lignin removal; the exception was NO formation from lignin lean soda liquors. The addition of biomass to black liquor resulted in a higher nitrogen content fuel mixture, due to the higher nitrogen content of biomass compared to black liquor. More NO and cyanate were formed from the fuel mixtures than from pure black liquor. The increased amount of formed cyanate led to the hypothesis that black liquor is catalytically active and converts a portion of the nitrogen in the mixed fuel to cyanate. The mechanism behind cyanate formation during thermal conversion of black liquor was not clear before this thesis. Paper IV studies the cyanate formation of alkali metal loaded fuels during gasification in a CO2 atmosphere. The salts K2CO3, Na2CO3, and K2SO4 all promoted char nitrogen to cyanate conversion during gasification, while KCl and CaCO3 did not. It is now assumed that cyanate is formed when alkali metal carbonate or an active intermediate of alkali metal carbonate (e.g. -CO2K) reacts with the char nitrogen forming cyanate. By testing different fuels (bark, peat, and coal), each of which had a different form of organic nitrogen, it was concluded that the form of organic nitrogen in char also has an impact on cyanate formation. Cyanate can be formed during pyrolysis of black liquor, but at temperatures 900°C or above, the formed cyanate will decompose. Cyanate formation in gasifying conditions with different levels of CO2 in the atmosphere was also studied. Most of the char nitrogen was converted to cyanate during gasification at 800-900°C in 13-50% CO2 in N2, and only 5% of the initial fuel nitrogen was converted to NO during char conversion. The formed smelt cyanate was stable at 800°C 13% CO2, while it decomposed at 900°C 13% CO2. The cyanate decomposition was faster at higher temperatures and in oxygen-containing atmospheres than in an inert atmosphere. The presence of CO2 in oxygencontaining atmospheres slowed down the decomposition of cyanate. This work will provide new information on how modification of black liquor affects the nitrogen chemistry during thermal conversion of black liquor and what causes cyanate formation during thermal conversion of black liquor. The formation and decomposition of cyanate was studied in order to provide new data, which would be useful in modeling of nitrogen chemistry in the recovery boiler.

Together Everyone Achieves More? Herding Behavior in the Finnish Stock Market

This thesis examines whether or not Finnish stock markets has herding behavior. Sample data is from 2004 to 2013. Including total of 2516 market days. Market wide herding, up and down market herding, extreme price movement herding and turnover volume herding are measured in this thesis. Methods used in this thesis are cross-sectional absolute dispersion and cross-sectional standard deviation. This thesis found no signs of herding in the Finnish stock market.

Forecasting financial weather - can we foresee market sentiment? Spectrum of stock price behavior - NYSE case study

The desire to create a statistical or mathematical model, which would allow predicting the future changes in stock prices, was born many years ago. Economists and mathematicians are trying to solve this task by applying statistical analysis and physical laws, but there are still no satisfactory results. The main reason for this is that a stock exchange is a non-stationary, unstable and complex system, which is influenced by many factors. In this thesis the New York Stock Exchange was considered as the system to be explored. A topological analysis, basic statistical tools and singular value decomposition were conducted for understanding the behavior of the market. Two methods for normalization of initial daily closure prices by Dow Jones and S&P500 were introduced and applied for further analysis. As a result, some unexpected features were identified, such as a shape of distribution of correlation matrix, a bulk of which is shifted to the right hand side with respect to zero. Also non-ergodicity of NYSE was confirmed graphically. It was shown, that singular vectors differ from each other by a constant factor. There are for certain results no clear conclusions from this work, but it creates a good basis for the further analysis of market topology.

Hygro-elasto-plastic behavior of planar orthotropic material

The mechanical and hygroscopic properties of paper and board are factors affecting the whole lifecycle of a product, including paper/board quality, production, converting, and material and energy savings. The progress of shrinkage profiles, loose edges of web, baggy web causing wrinkling and misregistration in printing are examples of factors affecting runnability and end product quality in the drying section and converting processes, where paper or board is treated as a moving web. The structural properties and internal stresses or plastic strain differences built up during production also cause the end-product defects related to distortion of the shape of the product such as sheet or box. The objective of this work was to construct a model capable of capturing the characteristic behavior of hygroscopic orthotropic material under moisture change, during different external in-plane stretch or stress conditions. Two independent experimental models were constructed: the elasto-plastic material model and the hygroexpansivity-shrinkage model. Both describe the structural properties of the sheet with a fiber orientation probability distribution, and both are functions of the dry solids content and fiber orientation anisotropy index. The anisotropy index, introduced in this work, simplifies the procedure of determining the constitutive parameters of the material model and the hygroexpansion coefficients in different in-plane directions of the orthotropic sheet. The mathematically consistent elasto-plastic material model and the dry solids content dependent hygroexpansivity have been constructed over the entire range from wet to dry. The presented elastoplastic and hygroexpansivity-shrinkage models can be used in an analytical approach to estimate the plastic strain and shrinkage in simple one-dimensional cases. For studies of the combined and more complicated effects of hygro-elasto-plastic behavior, both models were implemented in a finite element program for a numerical solution. The finite element approach also offered possibilities for studying different structural variations of orthotropic planar material, as well as local buckling behavior and internal stress situations of the sheet or web generated by local strain differences. A comparison of the simulation examples presented in this work to results published earlier confirms that the hygro-elasto-plastic model provides at least qualitatively reasonable estimates. The application potential of the hygro-elasto-plastic model is versatile, including several phenomena and defects appearing in the drying, converting and end-use conditions of the paper or board webs and products, or in other corresponding complex planar materials.

Permanent magnet synchronous generator design solution for large directdrive wind turbines: Thermal behavior of the LC DD-PMSG

Wind is one of the most compelling forms of indirect solar energy. Available now, the conversion of wind power into electricity is and will continue to be an important element of energy self-sufficiency planning. This paper is one in a series intended to report on the development of a new type of generator for wind energy; a compact, high-power, direct-drive permanent magnet synchronous generator (DD-PMSG) that uses direct liquid cooling (LC) of the stator windings to manage Joule heating losses. The main param-eters of the subject LC DD-PMSG are 8 MW, 3.3 kV, and 11 Hz. The stator winding is cooled directly by deionized water, which flows through the continuous hollow conductor of each stator tooth-coil winding. The design of the machine is to a large degree subordinate to the use of these solid-copper tooth-coils. Both steady-state and timedependent temperature distributions for LC DD-PMSG were examined with calculations based on a lumpedparameter thermal model, which makes it possible to account for uneven heat loss distribution in the stator conductors and the conductor cooling system. Transient calculations reveal the copper winding temperature distribution for an example duty cycle during variable-speed wind turbine operation. The cooling performance of the liquid cooled tooth-coil design was predicted via finite element analysis. An instrumented cooling loop featuring a pair of LC tooth-coils embedded in a lamination stack was built and laboratory tested to verify the analytical model. Predicted and measured results were in agreement, confirming the predicted satisfactory operation of the LC DD-PMSG cooling technology approach as a whole.

Psychological well-being of the parents and child development, behavior, and quality of life in very low birth weight infants

The parents of premature infants, especially the mothers, are at increased risk for distress. Infants born prematurely are at risk for developmental problems. The aim of this study was to investigate whether the psychological well-being of both parents is associated with child development in very low birth weight (VLBW, ≤1500g) children. The burden of prematurity-related morbidity to the children and to the family was also assessed. A cohort of 201 VLBW infants born during 2001–2006 in the Turku University Hospital, Finland, and their parents were studied (I–IV). One study included a control group (n=166) of full-term infants (IV). The psychological well-being of the parents was evaluated by assessments of depressive symptoms, parenting stress, the sense of coherence and general family functioning. Cognitive, behavioral, and socio-emotional development, and the health-related quality of life (HRQoL) of the children were determined when the children were 2 to 8 years old. The psychological well-being of the parents was associated with the cognitive, behavioral and social development of the VLBW children. The VLBW infants with prematurity-related morbidities had a poorer HRQoL and the general functioning of the family was inferior compared to the control children and their families. 64.5% of the VLBW children survived without morbidities. Most of the VLBW children did not have significant behavior problems (93%), had normal social skills (63%), had no emotional problems (64%), and had no problems in executive functioning (62%). Only 3% of the surviving VLBW infants had significant cognitive delay. In conclusion, the depressive symptoms and stress of the parents can be risk factors for disadvantageous child development, while a strong sense of coherence can be protective. Parents of the premature children with developmental delays might also experience more depressive symptoms and stress than other parents. Prematurity-related morbidities were a burden to the VLBW child as well as to the family.

Explaining the intention to play and behavior of playing sports betting games of young Finnish adults : an application of the theory of planned behavior

The aim of this Master’s Thesis was to examine the determinants of intention and behavior of playing sports betting games in order to explain the intention to play in a more precise way and to be able to understand the behavior of playing. The theory of planned behavior was applied in explaining the intention of young Finnish adults aged 18 to 34. A quantitative research method was applied and an online survey was sent to the students of Lappeenranta University of Technology and to the subscribers of Urheilulehti in order to reach a sample that present the young population of Finland. The theory of the study focused on the theory of planned behavior and its antecedents, attitude towards behavior, subjective norms, perceived behavioral control as well as motivation. By analyzing the data, causal relationships were found through which the explanation of intention was possible. The results showed that attitude towards playing, subjective norms, perceived behavioral control and motivation impact the formation of intention significantly. The results also indicated that intention impacts significantly to the playing frequency.

Effects of Fabrication Processes on the Behavior of S960 Ultra High Strength Steel (UHSS)

Strenx® 960 MC is a direct quenched type of Ultra High Strength Steel (UHSS) with low carbon content. Although this material combines high strength and good ductility, it is highly sensitive towards fabrication processes. The presence of stress concentration due to structural discontinuity or notch will highlight the role of these fabrication effects on the deformation capacity of the material. Due to this, a series of tensile tests are done on both pure base material (BM) and when it has been subjected to Heat Input (HI) and Cold Forming (CF). The surface of the material was dressed by laser beam with a certain speed to study the effect of HI while the CF is done by bending the specimen to a certain angle prior to tensile test. The generated results illustrate the impact of these processes on the deformation capacity of the material, specially, when the material has HI experience due to welding or similar processes. In order to compare the results with those of numerical simulation, LS-DYNA explicit commercial package has been utilized. The generated results show an acceptable agreement between experimental and numerical simulation outcomes.