Design and Control of Permanent Magnet Synchronous Machine for Hybrid Electric Vehicle

This master’s thesis mainly focuses on the design requirements of an Electric drive for Hybrid car application and its control strategy to achieve a wide speed range. It also emphasises how the control and performance requirements are transformed into its design variables. A parallel hybrid topology is considered where an IC engine and an electric drive share a common crank shaft. A permanent magnet synchronous machine (PMSM) is used as an electric drive machine. Performance requirements are converted into Machine design variables using the vector model of PMSM. Main dimensions of the machine are arrived using analytical approach and Finite Element Analysis (FEA) is used to verify the design and performance. Vector control algorithm was used to control the machine. The control algorithm was tested in a low power PMSM using an embedded controller. A prototype of 10 kW PMSM was built according to the design values. The prototype was tested in the laboratory using a high power converter. Tests were carried out to verify different operating modes. The results were in agreement with the calculations.

Novel Methods for Error Modeling and Parameter Identification of a Redundant Serial-Parallel Hybrid Robot

To obtain the desirable accuracy of a robot, there are two techniques available. The first option would be to make the robot match the nominal mathematic model. In other words, the manufacturing and assembling tolerances of every part would be extremely tight so that all of the various parameters would match the “design” or “nominal” values as closely as possible. This method can satisfy most of the accuracy requirements， but the cost would increase dramatically as the accuracy requirement increases. Alternatively, a more cost-effective solution is to build a manipulator with relaxed manufacturing and assembling tolerances. By modifying the mathematical model in the controller, the actual errors of the robot can be compensated. This is the essence of robot calibration. Simply put, robot calibration is the process of defining an appropriate error model and then identifying the various parameter errors that make the error model match the robot as closely as possible. This work focuses on kinematic calibration of a 10 degree-of-freedom (DOF) redundant serial-parallel hybrid robot. The robot consists of a 4-DOF serial mechanism and a 6-DOF hexapod parallel manipulator. The redundant 4-DOF serial structure is used to enlarge workspace and the 6-DOF hexapod manipulator is used to provide high load capabilities and stiffness for the whole structure. The main objective of the study is to develop a suitable calibration method to improve the accuracy of the redundant serial-parallel hybrid robot. To this end, a Denavit–Hartenberg (DH) hybrid error model and a Product-of-Exponential (POE) error model are developed for error modeling of the proposed robot. Furthermore, two kinds of global optimization methods, i.e. the differential-evolution (DE) algorithm and the Markov Chain Monte Carlo (MCMC) algorithm, are employed to identify the parameter errors of the derived error model. A measurement method based on a 3-2-1 wire-based pose estimation system is proposed and implemented in a Solidworks environment to simulate the real experimental validations. Numerical simulations and Solidworks prototype-model validations are carried out on the hybrid robot to verify the effectiveness, accuracy and robustness of the calibration algorithms.

Laser-TIG hybrid welding process

Joining processes and techniques need to meet the trend of new applications and the development of new materials. The application in connection with thick and thin plates in industrial fields is wide and the joining technology is in very urgent need. The laser-TIG hybrid welding technology can play the respective advantages of both of them. One major advantage of the hybrid laser-TIG welding technology is its efficient use of laser energy. Additionally, it can develop into a high and new advanced welding technology and become a hot spot in both the application and research area. This thesis investigated laser –TIG hybrid welding with the aim of enlightening the reader on its advantages, disadvantages and future areas of improvement. The main objective is to investigate laser-TIG hybrid on the welding of various metals (steels, magnesium, aluminium etc.). In addition, it elaborates on various possible combinations on hybrid laser-TIG welding technology and their benefits. The possibility of using laser-TIG hybrid in welding of thick materials was investigated. The method applied in carrying out this research is by using literature review. The results showed that hybrid laser-TIG is applicable to almost all weldable metals. Also it proves to be effective in welding refractive metals. The possibility of welding with or without filler materials is of economic advantage especially in welding of materials with no filler material. Thick plate’s hybrid laser-TIG welding is showing great prospects although it normally finds its used in welding thin materials in the range of 0.4 to 0.8 mm. The findings show that laser-TIG hybrid welding can be a versatile welding process and therefore will be increasingly used industrially due to its numerous advantages and the development of new TIG arc that enhances its capabilities.

Hezbollah and Taliban - hybrid adversaries in contemporary conflicts? : views on an adversary from the United States Armed Forces perspective

The experiences of the United States Armed Forces of the wars in Iraq and Afghanistan and Israel Defense Forces in the Second Lebanon War resulted a new term to surface called “hybrid warfare”. It was to describe the complexity of today’s battlefield. The term “hy-brid warfare” was never officially defined nor is it today. The updated version of the US ARMY Field Manual 3-0: Operations (Change 1) from February 22, 2011, introduced and defined “hybrid threat” and thus opened the discussion for hybrid adversary. In this thesis a model is introduced according to which any organization, group or an ad-versary can be examined and evaluated to see whether it qualifies as a hybrid adversary. It is demonstrated by the example of Hezbollah, which is recognized as the best example of an organization utilizing “hybrid warfare” and subsequently categorizing as a hybrid adver-sary. The model will be tested with Afghan Taliban to see whether both the model works and Taliban qualifies as a hybrid adversary or not. According to the model used in this thesis, it is concluded that Taliban does not meet the standards of a hybrid adversary, but with acquisition of standoff weapons it would quickly qualify as one. The model proved to work, and it could be used as a tool by intelligence of-ficers for estimating the threat levels of any group or identifying those groups that are al-ready or are about to develop into a hybrid adversary.

On the effects of new forms of foreign aid

-

Optimization of parameters for fiber laser-MAG hybrid welding in shipbuilding applications

The Arctic region becoming very active area of the industrial developments since it may contain approximately 15-25% of the hydrocarbon and other valuable natural resources which are in great demand nowadays. Harsh operation conditions make the Arctic region difficult to access due to low temperatures which can drop below -50 °C in winter and various additional loads. As a result, newer and modified metallic materials are implemented which can cause certain problems in welding them properly. Steel is still the most widely used material in the Arctic regions due to high mechanical properties, cheapness and manufacturability. Moreover, with recent steel manufacturing development it is possible to make up to 1100 MPa yield strength microalloyed high strength steel which can be operated at temperatures -60 °C possessing reasonable weldability, ductility and suitable impact toughness which is the most crucial property for the Arctic usability. For many years, the arc welding was the most dominant joining method of the metallic materials. Recently, other joining methods are successfully implemented into welding manufacturing due to growing industrial demands and one of them is the laser-arc hybrid welding. The laser-arc hybrid welding successfully combines the advantages and eliminates the disadvantages of the both joining methods therefore produce less distortions, reduce the need of edge preparation, generates narrower heat-affected zone, and increase welding speed or productivity significantly. Moreover, due to easy implementation of the filler wire, accordingly the mechanical properties of the joints can be manipulated in order to produce suitable quality. Moreover, with laser-arc hybrid welding it is possible to achieve matching weld metal compared to the base material even with the low alloying welding wires without excessive softening of the HAZ in the high strength steels. As a result, the laser-arc welding methods can be the most desired and dominating welding technology nowadays, and which is already operating in automotive and shipbuilding industries with a great success. However, in the future it can be extended to offshore, pipe-laying, and heavy equipment industries for arctic environment. CO2 and Nd:YAG laser sources in combination with gas metal arc source have been used widely in the past two decades. Recently, the fiber laser sources offered high power outputs with excellent beam quality, very high electrical efficiency, low maintenance expenses, and higher mobility due to fiber optics. As a result, fiber laser-arc hybrid process offers even more extended advantages and applications. However, the information about fiber or disk laser-arc hybrid welding is very limited. The objectives of the Master’s thesis are concentrated on the study of fiber laser-MAG hybrid welding parameters in order to understand resulting mechanical properties and quality of the welds. In this work only ferrous materials are reviewed. The qualitative methodological approach has been used to achieve the objectives. This study demonstrates that laser-arc hybrid welding is suitable for welding of many types, thicknesses and strength of steels with acceptable mechanical properties along very high productivity. New developments of the fiber laser-arc hybrid process offers extended capabilities over CO2 laser combined with the arc. This work can be used as guideline in hybrid welding technology with comprehensive study the effect of welding parameter on joint quality.

Victims’ status at international and hybrid criminal courts : victims’ status as witnesses, victim participants/civil parties and reparations claimants

Bestraffning av internationella brott vid internationella och hybrida straffrättsliga domstolar har traditionellt och huvudsakligen grundat sig på principen om retributiv (vedergällande) rättvisa och ackusatorisk process snarare än återuppbyggande rättvisa och en inkvisitorisk modell. Därav har brottsoffrens ställning vid dessa straffrättsliga domstolar begränsat sig till den som innehas av vittnen vid Tribunalen som behandlar brott som begåtts i det forna Jugoslavien (ICTY), Internationella krigsförbrytartribunalen för Rwanda (ICTR) och Specialdomstolen för Sierra Leone (SCSL). Internationella brottmålsdomstolen (ICC), å sin sida, har medfört en viktig förändring gällande brottsoffrens ställning i internationella straffrättsliga fora, vilket innebär att de från att ha betraktats endast i egenskap av vittnen nu även har en rätt att delta och lämna sina synpunkter (i egenskap av brottsofferdeltagare) samt kräva gottgörelse. Denna trend har fortsatt inom området för internationell straffrätt, vilket manifesterats vid hybridtribunaler som tillsatts efter ICC såsom Kambodjadomstolen (ECCC) vid vilken brottsoffer kan agera civilrättsliga parter och Specialdomstolen för Libanon (STL) där brottsoffer kan inneha en deltagande roll. Den föreliggande studien behandlar två huvudsakliga frågeställningar, av vilka den första lyder: Vilken ställning tillskrivs brottsoffren vid internationella domstolar och hybridtribunaler? I detta hänseende argumenterar författaren, sammanfattningsvis, för att brottsoffrens ställning vid internationella straffrättsliga domstolar och hybridtribunaler huvudsakligen tar sig uttryck på tre sätt, d.v.s. som brottsoffer i egenskap av vittnen, som brottsoffer i egenskap av deltagande brottsoffer/civilrättsliga parter samt som brottsoffer som kräver gottgörelse. Den andra frågeställningen för denna studie lyder: På vilket sätt fungerar brottsoffrens ställning som vittnen, brottsofferdeltagande/civilrättsliga parter och gottgörelsekrävande vid internationella och hybrida straffrättsliga domstolar? -------------------------------------------------------------------------------------------------------------------------------------------------- Kansainvälisten rikosten rankaiseminen kansainvälisissä rikostuomioistuimissa ja hybridituomioistuimissa on perinteisesti enimmäkseen perustunut retributiivisen oikeuden ja akkusatorisen menetelmän soveltamiseen pikemmin kuin restoratiivisen oikeuden ja inkvisitorisen menetelmän soveltamiseen. Niinpä uhrien asema kansainvälisissä rikostuomioistuimissa ja hybridituomioistuimissa on rajoittunut todistajan asemaan entisen Jugoslavian kansainvälisessä sotarikostuomioistuimessa (ICTY), Ruandan kansainvälisessä sotarikostuomioistuimessa (ICTR) ja Sierra Leonen erikoistuomioistuimessa (SCSL). Kansainvälisen rikostuomioistuimen (ICC) perustaminen on kuitenkin merkinnyt tärkeää muutosta uhrien asemaan kansainvälisen rikosoikeuden alalla siten, että kun uhrit aiemmin nähtiin vain todistajina, heillä on nyt myös mahdollisuus tuoda esiin omat näkökantansa (osallistumisoikeus) ja vaatia hyvitystä. Tämä suuntaus on jatkunut kansainvälisen rikosoikeuden alalla ICC:n jälkeen perustetuissa hybridituomioistuimissa, kuten Kambodzhan erityistuomioistuimessa (ECCC), missä uhrit voivat olla asianosaisen asemassa, sekä Libanonin erityistuomioistuimessa (STL), missä uhrit voivat osallistua prosessiin. Tämä tutkimus käsittelee kahta keskeistä kysymystä. Ensinnäkin: Mikä on rikoksen uhrien asema kansainvälisissä rikostuomioistuimissa ja hybridituomioistuimissa? Tutkimuksessa päädytään mm. siihen, että uhrien asema kansainvälisissä rikostuomioistuimissa ja hybridituomioistuimissa voi koostua pääosin kolmesta ulottuvuudesta eli uhrit todistajina, uhrit prosessiin osallistujina/asianosaisina ja uhrit hyvityksen hakijoina. Tutkimuksen toinen keskeinen kysymys on: Miten uhrien asema todistajina, prosessiin osallistujina/ asianosaisina ja hyvityksen hakijoina toimii kansainvälisissä rikostuomioistuimissa ja hybridituomioistuimissa?

Flexible multibody dynamics and intelligent control of a hydraulically driven hybrid redundant robot machine

The assembly and maintenance of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel (VV) is highly challenging since the tasks performed by the robot involve welding, material handling, and machine cutting from inside the VV. The VV is made of stainless steel, which has poor machinability and tends to work harden very rapidly, and all the machining operations need to be carried out from inside of the ITER VV. A general industrial robot cannot be used due to its poor stiffness in the heavy duty machining process, and this will cause many problems, such as poor surface quality, tool damage, low accuracy. Therefore, one of the most suitable options should be a light weight mobile robot which is able to move around inside of the VV and perform different machining tasks by replacing different cutting tools. Reducing the mass of the robot manipulators offers many advantages: reduced material costs, reduced power consumption, the possibility of using smaller actuators, and a higher payload-to-robot weight ratio. Offsetting these advantages, the lighter weight robot is more flexible, which makes it more difficult to control. To achieve good machining surface quality, the tracking of the end effector must be accurate, and an accurate model for a more flexible robot must be constructed. This thesis studies the dynamics and control of a 10 degree-of-freedom (DOF) redundant hybrid robot (4-DOF serial mechanism and 6-DOF 6-UPS hexapod parallel mechanisms) hydraulically driven with flexible rods under the influence of machining forces. Firstly, the flexibility of the bodies is described using the floating frame of reference method (FFRF). A finite element model (FEM) provided the Craig-Bampton (CB) modes needed for the FFRF. A dynamic model of the system of six closed loop mechanisms was assembled using the constrained Lagrange equations and the Lagrange multiplier method. Subsequently, the reaction forces between the parallel and serial parts were used to study the dynamics of the serial robot. A PID control based on position predictions was implemented independently to control the hydraulic cylinders of the robot. Secondly, in machining, to achieve greater end effector trajectory tracking accuracy for surface quality, a robust control of the actuators for the flexible link has to be deduced. This thesis investigates the intelligent control of a hydraulically driven parallel robot part based on the dynamic model and two schemes of intelligent control for a hydraulically driven parallel mechanism based on the dynamic model: (1) a fuzzy-PID self-tuning controller composed of the conventional PID control and with fuzzy logic, and (2) adaptive neuro-fuzzy inference system-PID (ANFIS-PID) self-tuning of the gains of the PID controller, which are implemented independently to control each hydraulic cylinder of the parallel mechanism based on rod length predictions. The serial component of the hybrid robot can be analyzed using the equilibrium of reaction forces at the universal joint connections of the hexa-element. To achieve precise positional control of the end effector for maximum precision machining, the hydraulic cylinder should be controlled to hold the hexa-element. Thirdly, a finite element approach of multibody systems using the Special Euclidean group SE(3) framework is presented for a parallel mechanism with flexible piston rods under the influence of machining forces. The flexibility of the bodies is described using the nonlinear interpolation method with an exponential map. The equations of motion take the form of a differential algebraic equation on a Lie group, which is solved using a Lie group time integration scheme. The method relies on the local description of motions, so that it provides a singularity-free formulation, and no parameterization of the nodal variables needs to be introduced. The flexible slider constraint is formulated using a Lie group and used for modeling a flexible rod sliding inside a cylinder. The dynamic model of the system of six closed loop mechanisms was assembled using Hamilton’s principle and the Lagrange multiplier method. A linearized hydraulic control system based on rod length predictions was implemented independently to control the hydraulic cylinders. Consequently, the results of the simulations demonstrating the behavior of the robot machine are presented for each case study. In conclusion, this thesis studies the dynamic analysis of a special hybrid (serialparallel) robot for the above-mentioned special task involving the ITER and investigates different control algorithms that can significantly improve machining performance. These analyses and results provide valuable insight into the design and control of the parallel robot with flexible rods.

The Rejection of Prioritarianism

Since the late 1990’s, a group of moral doctrines called prioritarianism has received a lot of interest from many moral philosophers. Many contemporary moral philosophers are attracted to prioritarianism to such an extent that they can be called prioritarians. In this book, however, I reject prioritarianism, including not only “pure” prioritarianism but also hybrid prioritarian views which mix one or more non-prioritarian elements with prioritarianism. This book largely revolves around certain problems and complications of prioritarianism and its particular forms. Those problems and complications are connected to risk, impartiality, the arbitrariness of prioritarian weightings and possible future individuals. On the one hand, I challenge prioritarianism through targeted objections to various specific forms of prioritarianism. All those targeted objections are connected to risk or possible future individuals. It seems to me that together they give good grounds for believing that prioritarianism is not the way to go. On the other hand, I challenge prioritarianism by pointing out and discussing certain general problems of prioritarianism. Those general problems are connected to impartiality and the arbitrariness of prioritarian weightings. They may give additional grounds for believing that all prioritarian views should be rejected. Prioritarianism can be seen as a type of weighted utilitarianism and thus as an extension of utilitarianism. Utilitarianism is morally ultimately concerned, and morally ultimately concerned only, with some kind of maximization of utility or expected utility. Prioritarianism, on the other hand, is morally ultimately concerned, and morally ultimately concerned only, with some kind of maximization of priority-weighted utility, expected priority-weighted utility or priority-weighted expected utility. Thus prioritarianism, unlike utilitarianism, is a distribution-sensitive moral view. Besides rejecting prioritarianism, I reject also various other distribution-sensitive moral views in this book. However, I do not reject distribution-sensitivity in morality, as I end up endorsing a type of distribution-sensitive hybrid utilitarianism which mixes non-utilitarian elements with utilitarianism.

Reinventing the third way : towards new forms of economic and democratic conduct

Avhandlingen studerar samspelet mellan det politiska och det ekonomiska systemet genom det föregående seklet, med speciellt fokus på den nyliberala omdaning som utspelats de senaste tre årtiondena. Med en liberaliserad ekonomi och en individualiserad människa måste också det politiska systemet utformas på ett annat sätt. Gradvisa förändringar har varit synliga, som den växande nätverksorganiseringen, dvs. att olika typer av utvecklingspolitik allt mer genomförs som ett samspel mellan samhällssektorerna, istället för att enbart utföras av den offentliga sektorn som tidigare. Genom fyra fallstudier i Österbotten demonstreras hur arenor för samverkan kan konstrueras i enlighet med vad den aktuella frågan kräver. Ett exempel är det innovationsnätverk som skapats i Karleby-Jakobstad-regionen, där offentliga och privata intressenter deltar, och som samtidigt bryter traditionella administrativa gränser. Ett annat mer negativt exempel är omstruktureringsprocessen i Kaskö-regionen eft er Metsä-Botnia-fabrikens nedläggning, där småkommunproblemet tillsammans med att den privata intressenten inte haft skyldighet att samverka lett till att en tillräckligt regionalt förankrad arena för en långsiktig utvecklingspolitik inte har kunnat skapas. Det här visar på trögheten i det finska systemet, där en stark enhetsstat och en splittrad kommunal nivå ur ett historiskt perspektiv hindrat flexibla anpassningar till samhällsförändringar. Avhandlingen visar att nätverksorganiseringen bör vara en integrerad del av de representativa strukturerna för att kunna påverka processernas utfall. Avhandlingen visar framförallt att deltagande och funktionellt definierade regionala och lokala arenor har stor potential, både ekonomiskt och demokratiskt. Det handlar om att skapa en kultur med aktiverade och engagerade medborgare, vilket står i kontrast till det allt mer passiverande representativa systemet. ---------------------------------------- Väitöskirja tutkii viime vuosisadan poliittisen ja taloudellisen järjestelmän vuorovaikutusta keskittyen erityisesti kolmen viimeisen vuosikymmenen uusliberaaliseen muutokseen. Talouden liberalisoituminen ja ihmisen individualisoituminen edellyttävät myös poliittisen järjestelmän mukautumista. Asteittaisia muutoksia on ollut havaittavissa, kuten kasvava verkosto-organisaatio, toisin sanoen eri alojen kehityspolitiikkaa toteutetaan yhä enemmän eri yhteiskuntasektoreiden vuorovaikutuksena, kun aikaisemmin ainoastaan julkinen sektori vastasi kehityspolitiikan toteuttamisesta. Pohjanmaan maakunnan neljän tapaustutkimuksen avulla osoitetaan, miten vuorovaikutusareena voidaan rakentaa kulloinkin ajankohtaisen asiakokonaisuuden ympärille. Tästä esimerkkinä on Kokkola-Pietarsaari –alueen innovaatioverkosto, johon osallistuvat sekä julkiset että yksityiset sidosryhmät ja joka samalla rikkoo perinteisiä hallinnollisia rajoja. Toinen, kielteisempi esimerkki on Kaskisten alueen rakennemu utosprosessi Metsä-Botnian tehtaan sulkemisen jälkeen. Siellä pienkuntaongelma yhdistettynä siihen, että yksityinen sidosryhmä ei ole ollut velvollinen tekemään yhteistyötä, on johtanut siihen, että ei ole kyetty luomaan alueen pitkäaikaiseen kehittämiseen sitoutunutta vuorovaikutusareenaa. Tämä osoittaa suomalaisen järjestelmän kankeuden, jossa historiallisesta näkökulmasta vahva yhtenäinen valtio ja hajanainen kuntataso estävät joustavan yhteiskuntamuutoksiin sopeutumisen. Väitöskirja osoittaa, että verkosto-organisaation on oltava yhteiskunnassa vaikuttaviin rakenteisiin integroitu osa, jotta se voi vaikuttaa prosessien tuloksiin. Väitöskirja osoittaa ennen kaikkea, että osallistuvilla ja toiminnallisesti määritellyillä alueellisilla ja paikallisilla areenoilla on suuri taloudellinen ja demokraattinen potentiaali. Passivoivan edustavan järjestelmän tilalle on luotava aktiivisten ja tavoitteisiin sitoutuneiden kansalaisten vuorovaikutusjärjestelmä.

Readout architectures for hybrid pixel detector readout chips

The original contribution of this thesis to knowledge are novel digital readout architectures for hybrid pixel readout chips. The thesis presents asynchronous bus-based architecture, a data-node based column architecture and a network-based pixel matrix architecture for data transportation. It is shown that the data-node architecture achieves readout efficiency 99% with half the output rate as a bus-based system. The network-based solution avoids “broken” columns due to some manufacturing errors, and it distributes internal data traffic more evenly across the pixel matrix than column-based architectures. An improvement of > 10% to the efficiency is achieved with uniform and non-uniform hit occupancies. Architectural design has been done using transaction level modeling (TLM) and sequential high-level design techniques for reducing the design and simulation time. It has been possible to simulate tens of column and full chip architectures using the high-level techniques. A decrease of > 10 in run-time is observed using these techniques compared to register transfer level (RTL) design technique. Reduction of 50% for lines-of-code (LoC) for the high-level models compared to the RTL description has been achieved. Two architectures are then demonstrated in two hybrid pixel readout chips. The first chip, Timepix3 has been designed for the Medipix3 collaboration. According to the measurements, it consumes < 1 W/cm^2. It also delivers up to 40 Mhits/s/cm^2 with 10-bit time-over-threshold (ToT) and 18-bit time-of-arrival (ToA) of 1.5625 ns. The chip uses a token-arbitrated, asynchronous two-phase handshake column bus for internal data transfer. It has also been successfully used in a multi-chip particle tracking telescope. The second chip, VeloPix, is a readout chip being designed for the upgrade of Vertex Locator (VELO) of the LHCb experiment at CERN. Based on the simulations, it consumes < 1.5 W/cm^2 while delivering up to 320 Mpackets/s/cm^2, each packet containing up to 8 pixels. VeloPix uses a node-based data fabric for achieving throughput of 13.3 Mpackets/s from the column to the EoC. By combining Monte Carlo physics data with high-level simulations, it has been demonstrated that the architecture meets requirements of the VELO (260 Mpackets/s/cm^2 with efficiency of 99%).

Twelve "daughters of Herodias" in as many forms of dress: famous Salomes and their costumes

Kollaasi Salomea esittäneistä oopperalaulajista: Henny Dima, Josephine von Hubbenet, Fanchette Verhunk, Signe von Rappe, Mme. Isnardon, Agnes Klebe, Malvine Kann, Kruszelnicka, Aino Ackté, Emma Destinn, Anna Sutter, Thyra Larsen.