Rovakaira Oy:n keskijänniteverkon kehittämissuunnitelma toimitusvarmuuskriteeristön näkökulmasta

Diplomityössä tavoitteena on etsiä teknistaloudellisimmat ratkaisut sekä tutkia niiden vaikutuksia sähkönjakeluverkoston käyttövarmuuteen ja luotettavuuteen toimitusvarmuuskriteeristön näkökulmasta. Lisäksi työssä esitetään uusi tunnusluku kriteeristön ylityksestä aiheutuvan haitan arvostukseen. Merkittävä osa Rovakaira Oy:n keskijänniteverkosta joudutaan uusimaan lähivuosikymmeninä teknistaloudellisen pitoajan täyttyessä. Verkon uusiminen antaa mahdollisuuden toteuttaa verkkoa nykyisiin vaatimuksiin paremmin sopivilla ratkaisuilla. Kehitysvaihtoehtoina vertaillaan johdon tien varteen siirtoa, maastokatkaisijoiden lisäämistä, pienitehoisten ja päättyvien haarajohtojen korvaamista 1 kV tekniikalla sekä pienoissähköaseman kannattavuutta. Työssä tarkastellaan yksityiskohtaisemmin Sodankylän käyttövarmuuden parantamista sähköasemavian aikana ja alueen kuormituksenkasvuun varautumista.

Energy storage in electric drive system

In recent years the environmental issues and the energy saving have become increasingly import in modern society where industry is the major emission factor and energy consumer. Generally, most of the total energy consumption is caused by electrical drives used in industrial applications and thus improving the performance of electrical drives give an opportunity to improve the energy efficiency. In this Master Thesis improving the energy efficiency in different electrical drives is clarified with different cases: regenerative braking in the electric grid or recovery of the braking energy into an energy storage. In addition, as an example, the energy consumption of an elevator is analyzed by measurements. From these measurement results it can be estimated how much the share of the standby energy consumption is from the total energy consumption and how much regenerative energy is available. The latter part of the thesis concentrates on determination of the properties of lithium iron phosphate battery with measurements.

Marketing Plan of Electric Vehicle Charging Solutions to USA

The purpose of the Thesis was to evaluate the business environment of electrical vehicle charging equipment (EVSE) in USA, find the key issues of entering the US EVSE markets and to form a marketing plan for possible market entry. The external market research analyzed the environment, customers, competitors and demand of EVSEs. In the internal analysis the focus was on resources and capabilities, offering, performance, business relations and US related issues. The research about the business environment was done using already available information from market studies and seminars. In external analysis there were also two semi-structured interviews from market experts used. The internal analysis was done mostly by interviews, but also company’s internal data sources were used. The interviews were semi-constructed and included eight interviewees from each part of EVSE value chain. The research findings were analyzed using SWOT analysis, which was converted to a so called TOWS matrix for extracting strategies. As a result of the Thesis, valuable information about the US markets and their requirements for EVSEs was gained. By matching the strengths of the case company and market requirements, customer segmentation and targeting were done and a marketing plan was constructed for the case company to help their management to evaluate the feasibility of possible market entry and investments to USA.

Design of Pulsed Electroacoustic Measurement System for Space Charge Characterisation

Pulsed electroacoustic (PEA) method is a commonly used non-destructive technique for investigating space charges. It has been developed since early 1980s. These days there is continuing interest for better understanding of the influence of space charge on the reliability of solid electrical insulation under high electric field. The PEA method is widely used for space charge profiling for its robust and relatively inexpensive features. The PEA technique relies on a voltage impulse used to temporarily disturb the space charge equilibrium in a dielectric. The acoustic wave is generated by charge movement in the sample and detected by means of a piezoelectric film. The spatial distribution of the space charge is contained within the detected signal. The principle of such a system is already well established, and several kinds of setups have been constructed for different measurement needs. This thesis presents the design of a PEA measurement system as a systems engineering project. The operating principle and some recent developments are summarised. The steps of electrical and mechanical design of the instrument are discussed. A common procedure for measuring space charges is explained and applied to verify the functionality of the system. The measurement system is provided as an additional basic research tool for the Corporate Research Centre of ABB (China) Ltd. It can be used to characterise flat samples with thickness of 0.2–0.5 mm under DC stress. The spatial resolution of the measurement is 20 μm.

Monimoottorikäyttöjen suojaukset, mitoitus ja ohjeistus

Työssä tutkitaan pienitehoisen monimoottoritaajuusmuuttajakäytön yhteismuotovirtojen aiheuttamia ongelmia. Työn tavoitteena on muodostaa monimoottorikäyttöjen toteuttajille opastus, jonka avulla sähkökäytön suunnittelun alkuvaiheessa voidaan ottaa huomioon monimoottorikäytön erikoistarpeita. Työn teoriaosuudessa esitellään taajuusmuuttajan vaihtosuuntaustekniikan aiheuttamia ongelmia, moottorikaapelin mallintamista ja vertaillaan ongelmien ratkaisukeinoja pienitehoisten taajuusmuuttajien näkökulmasta. Yhteismuotoista virtaa tutkitaan mittaamalla rakennetulla monimoottorikäytöllä sekä simuloimalla vaihdellen kaapelin pituutta ja moottorien lukumäärää. Mittaamalla vertaillaan myös virran suodatusratkaisuja. Muodostettu simulointimalli on hyvin yksinkertainen ja luotettavammat virta-arvot saadaankin mittauksella. Kuitenkin työn perusteella voidaan antaa ohjeita monimoottorikäytön suunnittelulle. Esimerkiksi jokaiselle moottorille täytyy suunnitella erillinen suojaus ja taajuusmuuttaja on syytä mitoittaa todellisen kuormavirran mukaan. Yhteismuotoisen virran aiheuttamat ongelmat ovat sitä pienempiä, mitä vähemmän moottoreita on rinnakkain ja mitä lyhyempi moottorikaapelien yhteispituus on.

Design and Control of Permanent Magnet Synchronous Machine for Hybrid Electric Vehicle

This master’s thesis mainly focuses on the design requirements of an Electric drive for Hybrid car application and its control strategy to achieve a wide speed range. It also emphasises how the control and performance requirements are transformed into its design variables. A parallel hybrid topology is considered where an IC engine and an electric drive share a common crank shaft. A permanent magnet synchronous machine (PMSM) is used as an electric drive machine. Performance requirements are converted into Machine design variables using the vector model of PMSM. Main dimensions of the machine are arrived using analytical approach and Finite Element Analysis (FEA) is used to verify the design and performance. Vector control algorithm was used to control the machine. The control algorithm was tested in a low power PMSM using an embedded controller. A prototype of 10 kW PMSM was built according to the design values. The prototype was tested in the laboratory using a high power converter. Tests were carried out to verify different operating modes. The results were in agreement with the calculations.

Aging based maintenance and reinvestment scheduling of electric distribution

The maintenance of electric distribution network is a topical question for distribution system operators because of increasing significance of failure costs. In this dissertation the maintenance practices of the distribution system operators are analyzed and a theory for scheduling maintenance activities and reinvestment of distribution components is created. The scheduling is based on the deterioration of components and the increasing failure rates due to aging. The dynamic programming algorithm is used as a solving method to maintenance problem which is caused by the increasing failure rates of the network. The other impacts of network maintenance like environmental and regulation reasons are not included to the scope of this thesis. Further the tree trimming of the corridors and the major disturbance of the network are not included to the problem optimized in this thesis. For optimizing, four dynamic programming models are presented and the models are tested. Programming is made in VBA-language to the computer. For testing two different kinds of test networks are used. Because electric distribution system operators want to operate with bigger component groups, optimal timing for component groups is also analyzed. A maintenance software package is created to apply the presented theories in practice. An overview of the program is presented.

Active inverter output filtering methods

Frequency converters are widely used in the industry to enable better controllability and efficiency of variable speed AC motor drives. Despite these advantages, certain challenges concerning the inverter and motor interfacing have been present for decades. As insulated gate bipolar transistors entered the market, the inverter output voltage transition rate significantly increased compared with their predecessors. Inverters operate based on pulse width modulation of the output voltage, and the steep voltage edge fed by the inverter produces a motor terminal overvoltage. The overvoltage causes extra stress to the motor insulation, which may lead to a prematuremotor failure. The overvoltage is not generated by the inverter alone, but also by the sum effect of the motor cable length and the impedance mismatch between the cable and the motor. Many solutions have been shown to limit the overvoltage, and the mainstream products focus on passive filters. This doctoral thesis studies an alternative methodology for motor overvoltage reduction. The focus is on minimization of the passive filter dimensions, physical and electrical, or better yet, on operation without any filter. This is achieved by additional inverter control and modulation. The studied methods are implemented on different inverter topologies, varying in nominal voltage and current.For two-level inverters, the studied method is termed active du/dt. It consists of a small output LC filter, which is controlled by an independent modulator. The overvoltage is limited by a reduced voltage transition rate. For multilevel inverters, an overvoltage mitigation method operating without a passive filter, called edge modulation, is implemented. The method uses the capability of the inverter to produce two switching operations in the same direction to cancel the oscillating voltages of opposite phases. For parallel inverters, two methods are studied. They are both intended for two-level inverters, but the first uses individual motor cables from each inverter while the other topology applies output inductors. The overvoltage is reduced by interleaving the switching operations to produce a similar oscillation accumulation as with the edge modulation. The implementation of these methods is discussed in detail, and the necessary modifications to the control system of the inverter are presented. Each method is experimentally verified by operating industrial frequency converters with the modified control. All the methods are found feasible, and they provide sufficient overvoltage protection. The limitations and challenges brought about by the methods are discussed.

Design of an amplifier and an instrumentation setup for a harsh environment heat flux measurement application – case axial flux electric machine

Measurement is a tool for researching. Therefore, it is important that the measuring process is carried out correctly, without distorting the signal or the measured event. Researches of thermoelectric phenomena have been focused more on transverse thermoelectric phenomena during recent decades. Transverse Seebeck effect enables to produce thinner and faster heat flux sensor than before. Studies about transverse Seebeck effect have so far focused on materials, so in this Master’s Thesis instrumentation of transverse Seebeck effect based heat flux sensor is studied, This Master’s Thesis examines an equivalent circuit of transverse Seebeck effect heat flux sensors, their connectivity to electronics and choosing and design a right type amplifier. The research is carried out with a case study which is Gradient Heat Flux Sensors and an electrical motor. In this work, a general equivalent circuit was presented for the transverse Seebeck effect-based heat flux sensor. An amplifier was designed for the sensor of the case study, and the solution was produced for the measurement of the local heat flux of the electric motor to improve the electromagnetic compatibility.

Energy Efficiency of a Diesel-Electric MobileWorking Machine

The power demand of many mobile working machines such as mine loaders, straddle carriers and harvesters varies significantly during operation, and typically, the average power demand of a working machine is considerably lower than the demand for maximum power. Consequently, for most of the time, the diesel engine of a working machine operates at a poor efficiency far from its optimum efficiency range. However, the energy efficiency of dieseldriven working machines can be improved by electric hybridization. This way, the diesel engine can be dimensioned to operate within its optimum efficiency range, and the electric drive with its energy storages responds to changes in machine loading. A hybrid working machine can be implemented in many ways either as a parallel hybrid, a series hybrid or a combination of these two. The energy efficiency of hybrid working machines can be further enhanced by energy recovery and reuse. This doctoral thesis introduces the component models required in the simulation model of a working machine. Component efficiency maps are applied to the modelling; the efficiency maps for electrical machines are determined analytically in the whole torque–rotational speed plane based on the electricalmachine parameters. Furthermore, the thesis provides simulation models for parallel, series and parallel-series hybrid working machines. With these simulation models, the energy consumption of the working machine can be analysed. In addition, the hybridization process is introduced and described. The thesis provides a case example of the hybridization and dimensioning process of a working machine, starting from the work cycle of the machine. The selection and dimensioning of the hybrid system have a significant impact on the energy consumption of a hybrid working machine. The thesis compares the energy consumption of a working machine implemented by three different hybrid systems (parallel, series and parallel-series) and with different component dimensions. The payback time of a hybrid working machine and the energy storage lifetime are also estimated in the study.

Energy Efficiency Consideration in Electric Vehicle Transmission

This study is a survey of benefits and drawbacks of embedding a variable gearbox instead of a single reduction gear in electric vehicle powertrain from efficiency point of view. Losses due to a pair of spur gears meshing with involute teeth are modeled on the base of Coulomb’s law and fluid mechanics. The model for a variable gearbox is fulfilled and further employed in a complete vehicle simulation. Simulation model run for a single reduction gear then the results are taken as benchmark for other types of commonly used transmissions. Comparing power consumption, which is obtained from simulation model, shows that the extra load imposed by variable transmission components will shade the benefits of efficient operation of electric motor. The other accomplishment of this study is a combination of modified formulas that led to a new methodology for power loss prediction in gear meshing which is compatible with modern design and manufacturing technology.

Electric field control of magnetism in hydrid ferromagnetic / ferroelectric materials

Väisälän palkinnon 2012 saaja.

Power-line-communication-based data transmission concept for an LVDC electricity distribution network – Analysis and implementation

Communications play a key role in modern smart grids. New functionalities that make the grids ‘smart’ require the communication network to function properly. Data transmission between intelligent electric devices (IEDs) in the rectifier and the customer-end inverters (CEIs) used for power conversion is also required in the smart grid concept of the low-voltage direct current (LVDC) distribution network. Smart grid applications, such as smart metering, demand side management (DSM), and grid protection applied with communications are all installed in the LVDC system. Thus, besides remote connection to the databases of the grid operators, a local communication network in the LVDC network is needed. One solution applied to implement the communication medium in power distribution grids is power line communication (PLC). There are power cables in the distribution grids, and hence, they may be applied as a communication channel for the distribution-level data. This doctoral thesis proposes an IP-based high-frequency (HF) band PLC data transmission concept for the LVDC network. A general method to implement the Ethernet-based PLC concept between the public distribution rectifier and the customerend inverters in the LVDC grid is introduced. Low-voltage cables are studied as the communication channel in the frequency band of 100 kHz–30 MHz. The communication channel characteristics and the noise in the channel are described. All individual components in the channel are presented in detail, and a channel model, comprising models for each channel component is developed and verified by measurements. The channel noise is also studied by measurements. Theoretical signalto- noise ratio (SNR) and channel capacity analyses and practical data transmission tests are carried out to evaluate the applicability of the PLC concept against the requirements set by the smart grid applications in the LVDC system. The main results concerning the applicability of the PLC concept and its limitations are presented, and suggestion for future research proposed.

Economical potential of controlling charging of electric vehicles by using price signal

The number of electric vehicles grows continuously and the implementation of charging electric vehicles is an important issue for the future. Increasing amount of electric vehicles can cause problems to distribution grid by increasing peak load. Currently charging of electric vehicles is uncontrolled, but as the amount of electric vehicles grows, smart charg-ing (controlled charging) will be one possible solution to handle this situation. In this thesis smart charging of electric vehicles is examined from electricity retailers` point of view. The purpose is to find out plausible saving potentials of smart charging, when it´s controlled by price signal. Saving potential is calculated by comparing costs of price signal controlled charging and uncontrolled charging.

Process modeling method for electric accessories manufacturing enterprise

The theoretical research of the study focused to business process management and business process modeling, the goal was to found a new business process modeling method for electrical accessories manufacturing enterprise. The focus was to find few options for business process modeling methods where company could have chosen the best one for its needs The study was carried out as a qualitative research with an action study and a case study as the most important ways collect data. In the empirical part of the study examples of company’s processes modeled with the new modeling method and process modeling process are presented. The new way of modeling processes improves especially visual presentation of the processes and improves the understanding how employees should work in the organizational interfaces of the process and in the interfaces between different processes. The results of the study is a new unified way to model company’s processes, which makes it easier to understand and create the process models. This improved readability makes it possible to reduce the costs that were created from the unclear old process models.