Development of Craniofacial Bone Defect Reconstruction Implant Based on Fibre-Reinforced Composite with Photopolymerisable Resin Systems. Experimental studies in vitro and in vivo.

Reconstruction of defects in the craniomaxillofacial (CMF) area has mainly been based on bone grafts or metallic fixing plates and screws. Particularly in the case of large calvarial and/or craniofacial defects caused by trauma, tumours or congenital malformations, there is a need for reliable reconstruction biomaterials, because bone grafts or metallic fixing systems do not completely fulfill the criteria for the best possible reconstruction methods in these complicated cases. In this series of studies, the usability of fibre-reinforced composite (FRC) was studied as a biostable, nonmetallic alternative material for reconstructing artificially created bone defects in frontal and calvarial areas of rabbits. The experimental part of this work describes the different stages of the product development process from the first in vitro tests with resin-impregnated fibrereinforced composites to the in vivo animal studies, in which this FRC was tested as an implant material for reconstructing different size bone defects in rabbit frontal and calvarial areas. In the first in vitro study, the FRC was polymerised in contact with bone or blood in the laboratory. The polymerised FRC samples were then incubated in water, which was analysed for residual monomer content by using high performance liquid chromatography (HPLC). It was found that this in vitro polymerisation in contact with bone and blood did not markedly increase the residual monomer leaching from the FRC. In the second in vitro study, different adhesive systems were tested in fixing the implant to bone surface. This was done to find an alternative implant fixing system to screws and pins. On the basis of this study, it was found that the surface of the calvarial bone needed both mechanical and chemical treatments before the resinimpregnated FRC could be properly fixed onto it. In three animal studies performed with rabbit frontal bone defects and critical size calvarial bone defect models, biological responses to the FRC implants were evaluated. On the basis of theseevaluations, it can be concluded that the FRC, based on E-glass (electrical glass) fibres forming a porous fibre veil enables the ingrowth of connective tissues to the inner structures of the material, as well as the bone formation and mineralization inside the fibre veil. Bone formation could be enhanced by using bioactive glass granules fixed to the FRC implants. FRC-implanted bone defects healed partly; no total healing of defects was achieved. Biological responses during the follow-up time, at a maximum of 12 weeks, to resin-impregnated composite implant seemed to depend on the polymerization time of the resin matrix of the FRC. Both of the studied resin systems used in the FRC were photopolymerised and the heat-induced postpolymerisation was used additionally.

Developing Service Promise Concept Based on Supply Chain

Diplomityön tavoitteena on analysoida ja kehittää palvelulupauskonseptia toimitusketjuun perustuen Halton Oy:ssä. Työ toteutettiin, koska asiakaslähtöinen liiketoimintatapa on voimakkaasti valtaamassa alaa tuote- ja tuotantopainotteiselta toimintatavalta. Tuotteiden erinomaisuus koetaan markkinoilla yhä useammin itsestään selvyytenä. Prosessien tehokas hallitseminen ja asiakkaan kokeman lisäarvon muodostaminen ovat muodostuneet ratkaisevimmaksi kilpailuedun luojaksi. Toimitusketjun hallinnalla ja sähköisellä kaupankäynnillä on tärkeä rooli tämän kilpailuedun muodostumisessa.Diplomityö käsittelee uuden palvelulupauskonseptin tarjoamia etuja Halton Oy:lle. Työssä pureudutaan toimitusketjun ja sähköisen kaupankäynnin integraatiomahdollisuuksiin. Tarkoituksena on selvittää parhaat mahdolliset kriteerit Haltonin palvelulupauskonseptilleja luoda menetelmät yrityksen materiaalivirtojen sekä uuden konseptin analysoinnille ja kehittämiselle jatkossa.

Investigation ofsolid - state cooler based on electrocaloric effect

Electrocaloric cooling based on ability of material to change temperature by applying an electric field under adiabatic conditions is relatively new and challenging direction of ferroelectrics research. In this work we report about analytical, simulation and experimental data for BaSrTiO3 thin film and bulk ceramic samples. Detailed discussion of a theoretical base of the electrocaloric effect is included. Demonstrated experimental and computational results exemplify rational approach to a problem of solid-state cooler construction.

Evaluation of an eLearning pilot course based on user experiences: corporate case study

Diplomityön tavoitteena oli arvioida sähköisen oppimisen soveltuvuutta kohdeyrityksessä ja selvittää, voidaanko luokkahuonekoulutusta korvata sähköisen oppimisen kursseilla. Tietojärjestelmän raportoinnista tehtiin sähköisen oppimisen kurssi, joka oli koekäytössä. Koekäytön jälkeen tehtiin käyttäjäkysely, kerättiin käyttötietoja kurssista ja tehtiin haastatteluja. Koekäyttäjien kokemuksista tehdyn arvioinnin perusteella sähköinen oppiminen soveltuu käytettäväksi selkeiden asioiden koulutukseen kohdeyrityksessä, mutta se ei voi kokonaan korvata luokkahuonekoulutusta. Luokkahuonekoulutuksessa tulisi keskittyä monimutkaisempiin asioihin ja ongelmanratkaisuun. Positiivisten tulosten perusteella sähköisen oppimisen kehittämistä päätettiin jatkaa yrityksessä. Sähköisen oppimisen kurssin avulla saadaan kustannussäästöjä kohdeyrityksessä, kun käyttäjämäärä on suurempi kuin 66. Jos koko koekäytössä olleen kurssin kohdeyleisö suorittaa kurssin sähköisesti, ovat kustannukset vain noin 15% vastaavista kustannuksista luokkahuoneessa järjestettynä. Lisäksi sähköisen oppimisen tehokkuutta tutkittiin ja koekäytössä olleen kurssin arvioitiin olevan positiivinen työssä kehitetyn Consensus-mallin mukaan.

Transfer pricing tool development process based on valve package production costs

Tämän diplomityön päätavoitteena oli parantaa kehitetyn kustannusperusteisen siirtohinnoittelutyökalun ominaisuuksia osastokohtaisen kustannusarviointiprosessin käyttöön. Työ on vaikeutunut lähimenneisyyden heikosta hintakyselyiden vastauskyvystä. Työn pääongelmana oli kerätä luotettavaa tuotannonohjausjärjestelmän kustannusaineistoa osittain vanhentuneista vakioventtiilien koneistus- ja materiaalitiedosta. Tutkimuksessa käytetyt tärkeimmät tutkimusmenetelmät voidaan jakaa siirtohinnoittelu- ja kustannusarvioprosessien kirjallisuustutkimukseen, kenttäanalyysiin ja nykyisen Microsoft Excel –siirtohinnoittelutyökalun kehittämiseen eri osastojen rajapinnassa. Siirtohinnoittelumenetelmät ovat yleisesti jaettu kustannus-, markkina- ja neuvotteluperusteisiin malleihin, jotka harvoin sellaisenaan kohtaavat siirtohinnoittelulle asetetut tavoitteet. Tämä ratkaisutapa voi johtaa tilanteisiin, jossa kaksi erillistä menetelmää sulautuvat yhteen. Lisäksi varsinaiseen siirtohinnoittelujärjestelmään yleensä vaikuttavat useat sisäiset ja ulkoiset tekijät. Lopullinen siirtohinnoittelumenetelmä tulisi ehdottomasti tukea myös yrityksen visiota ja muita liiketoiminnalle asetettuja strategioita. Työn tuloksena saatiin laajennettu Microsoft Excel –sovellus, joka vaatii sekä vuosittaista että kuukausittaista erikoisventtiilimateriaalien hinta- ja toimitusaikatietojen päivittämistä. Tämä ratkaisutapa ehdottomasti parantaa kustannusarviointiprosessia, koska myös alihankkijatietoja joudutaan tutkimaan systemaattisesti. Tämän jälkeen koko siirtohinnoitteluprosessia voidaan kehittää muuntamalla kokoonpano- ja testaustyövaiheiden kustannusrakennetta toimintoperustaisen kustannuslaskentamallin mukaiseksi.

GPS-signal Source Based on Direct Digital Synthesis

This thesis presents the design and implementation of a GPS-signal source suitable for receiver measurements. The developed signal source is based on direct digital synthesis which generates the intermediate frequency. The intermediate frequency is transfered to the final frequency with the aid of an Inphase/Quadrature modulator. The modulating GPS-data was generated with MATLAB. The signal source was duplicated to form a multi channel source. It was shown that, GPS-signals ment for civil navigation are easy to generate in the laboratory. The hardware does not need to be technically advanced if navigation with high level of accuracy is not needed. It was also shown that, the Inphase/Quadrature modulator can function as a single side band upconverter even with a high intermediate frequency. This concept reduces the demands required for output filtering.

Position sensorless electrically excited synchronous motor drive for industrial use based on direct flux linkage and torque control

Synchronous machines with an AC converter are used mainly in large drives, for example in ship propulsion drives as well as in rolling mill drives in steel industry. These motors are used because of their high efficiency, high overload capacity and good performance in the field weakening area. Present day drives for electrically excited synchronous motors are equipped with position sensors. Most drives for electrically excited synchronous motors will be equipped with position sensors also in future. This kind of drives with good dynamics are mainly used in metal industry. Drives without a position sensor can be used e.g. in ship propulsion and in large pump and blower drives. Nowadays, these drives are equipped with a position sensor, too. The tendency is to avoid a position sensor if possible, since a sensor reduces the reliability of the drive and increases costs (latter is not very significant for large drives). A new control technique for a synchronous motor drive is a combination of the Direct Flux Linkage Control (DFLC) based on a voltage model and a supervising method (e.g. current model). This combination is called Direct Torque Control method (DTC). In the case of the position sensorless drive, the DTC can be implemented by using other supervising methods that keep the stator flux linkage origin centered. In this thesis, a method for the observation of the drift of the real stator flux linkage in the DTC drive is introduced. It is also shown how this method can be used as a supervising method that keeps the stator flux linkage origin centered in the case of the DTC. In the position sensorless case, a synchronous motor can be started up with the DTC control, when a method for the determination of the initial rotor position presented in this thesis is used. The load characteristics of such a drive are not very good at low rotational speeds. Furthermore, continuous operation at a zero speed and at a low rotational speed is not possible, which is partly due to the problems related to the flux linkage estimate. For operation in a low speed area, a stator current control method based on the DFLC modulator (DMCQ is presented. With the DMCC, it is possible to start up and operate a synchronous motor at a zero speed and at low rotational speeds in general. The DMCC is necessary in situations where high torque (e.g. nominal torque) is required at the starting moment, or if the motor runs several seconds at a zero speed or at a low speed range (up to 2 Hz). The behaviour of the described methods is shown with test results. The test results are presented for the direct flux linkage and torque controlled test drive system with a 14.5 kVA, four pole salient pole synchronous motor with a damper winding and electric excitation. The static accuracy of the drive is verified by measuring the torque in a static load operation, and the dynamics of the drive is proven in load transient tests. The performance of the drive concept presented in this work is sufficient e.g. for ship propulsion and for large pump drives. Furthermore, the developed methods are almost independent of the machine parameters.

Development of beam and plate finite elements based on the absolute nodal coordinate formulation

The focus of this dissertation is to develop finite elements based on the absolute nodal coordinate formulation. The absolute nodal coordinate formulation is a nonlinear finite element formulation, which is introduced for special requirements in the field of flexible multibody dynamics. In this formulation, a special definition for the rotation of elements is employed to ensure the formulation will not suffer from singularities due to large rotations. The absolute nodal coordinate formulation can be used for analyzing the dynamics of beam, plate and shell type structures. The improvements of the formulation are mainly concentrated towards the description of transverse shear deformation. Additionally, the formulation is verified by using conventional iso-parametric solid finite element and geometrically exact beam theory. Previous claims about especially high eigenfrequencies are studied by introducing beam elements based on the absolute nodal coordinate formulation in the framework of the large rotation vector approach. Additionally, the same high eigenfrequency problem is studied by using constraints for transverse deformation. It was determined that the improvements for shear deformation in the transverse direction lead to clear improvements in computational efficiency. This was especially true when comparative stress must be defined, for example when using elasto-plastic material. Furthermore, the developed plate element can be used to avoid certain numerical problems, such as shear and curvature lockings. In addition, it was shown that when compared to conventional solid elements, or elements based on nonlinear beam theory, elements based on the absolute nodal coordinate formulation do not lead to an especially stiff system for the equations of motion.

Modelling mean above and below ground litter production based on yield tables

Selective papers of the workshop on "Development of models and forest soil surveys for monitoring of soil carbon", Koli, Finland, April 5-9 2006.

On convergence of transforms based on parabolic scaling

This thesis studies properties of transforms based on parabolic scaling, like Curvelet-, Contourlet-, Shearlet- and Hart-Smith-transform. Essentially, two di erent questions are considered: How these transforms can characterize H older regularity and how non-linear approximation of a piecewise smooth function converges. In study of Hölder regularities, several theorems that relate regularity of a function f : R2 → R to decay properties of its transform are presented. Of particular interest is the case where a function has lower regularity along some line segment than elsewhere. Theorems that give estimates for direction and location of this line, and regularity of the function are presented. Numerical demonstrations suggest also that similar theorems would hold for more general shape of segment of low regularity. Theorems related to uniform and pointwise Hölder regularity are presented as well. Although none of the theorems presented give full characterization of regularity, the su cient and necessary conditions are very similar. Another theme of the thesis is the study of convergence of non-linear M ─term approximation of functions that have discontinuous on some curves and otherwise are smooth. With particular smoothness assumptions, it is well known that squared L2 approximation error is O(M-2(logM)3) for curvelet, shearlet or contourlet bases. Here it is shown that assuming higher smoothness properties, the log-factor can be removed, even if the function still is discontinuous.